| /* |
| * This file is part of the coreboot project. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| /* |
| * This file initializes the CPU cores for voltage and frequency settings |
| * in the different power states. |
| */ |
| /* |
| |
| checklist (functions are in this file if no source file named) |
| Fam10 Bios and Kernel Development Guide #31116, rev 3.48, April 22, 2010 |
| |
| 2.4.2.6 Requirements for p-states |
| |
| 1.- F3x[84:80] According to table 100 : prep_fid_change |
| |
| 2.- COF/VID : |
| 2.4.2.9.1 Steps 1,3-6 and warning for 2,7 if they apply |
| fixPsNbVidBeforeWR(...) |
| 2.4.2.9.1 Step 8 enable_fid_change |
| We do this for all nodes, I don't understand BKDG 100% on |
| whether this is or isn't meant by "on the local |
| processor". Must be OK. |
| 2.4.2.9.1 Steps 9-10 (repeat 1-7 and reset) romstage.c/init_cpus ? |
| 2.4.2.9.1 Steps 11-12 init_fidvid_stage2 |
| 2.4.2.9.2 DualPlane PVI : Not supported, don't know how to detect, |
| needs specific circuitry. |
| |
| 3.- 2.4.2.7 dualPlaneOnly(dev) |
| |
| 4.- 2.4.2.8 applyBoostFIDOffset(dev, nodeid) |
| |
| 5.- enableNbPState1(dev) |
| |
| 6.- 2.4.1.7 |
| a) UpdateSinglePlaneNbVid() |
| b) setVSRamp(), called from prep_fid_change |
| c) prep_fid_change |
| d) improperly, for lack of voltage regulator details?, |
| F3xA0[PsiVidEn] in defaults.h |
| F3xA0[PsiVid] in init_cpus.c AMD_SetupPSIVID_d (before prep_fid_change) |
| |
| 7.- TODO (Core Performance Boost is only available in revision E cpus, and we |
| don't seem to support those yet, at least they don't have any |
| constant in amddefs.h ) |
| |
| 8.- FIXME ? Transition to min Pstate according to 2.4.2.15.3 is required |
| by 2.4.2.6 after warm reset. But 2.4.2.15 states that it is not required |
| if the warm reset is issued by coreboot to update NbFid. So it is required |
| or not ? How can I tell who issued warm reset ? |
| coreboot transitions to P0 instead, which is not recommended, and does |
| not follow 2.4.2.15.2 to do so. |
| |
| 9.- TODO Requires information on current delivery capability |
| (depends on mainboard and maybe power supply ?). One might use a config |
| option with the maximum number of Amperes that the board can deliver to CPU. |
| |
| 10.- [Multiprocessor] TODO 2.4.2.12 |
| [Uniprocessor] FIXME ? We call setPStateMaxVal() in init_fidvid_stage2, |
| but not sure this is what is meant by "Determine the valid set of |
| P-states based on enabled P-states indicated |
| in MSRC001_00[68:64][PstateEn]" in 2.4.2.6-10 |
| |
| 11.- finalPstateChange() from init_fidvid_Stage2 (BKDG says just "may", anyway) |
| |
| 12.- generate ACPI for p-states. |
| generated in powernow_acpi.c amd_generate_powernow() |
| |
| "must also be completed" |
| |
| a.- PllLockTime set in ruleset in defaults.h |
| BKDG says set it "If MSRC001_00[68:64][CpuFid] is different between |
| any two enabled P-states", but since it does not say "only if" |
| I guess it is safe to do it always. |
| |
| b.- prep_fid_change(...) |
| |
| */ |
| |
| #include <console/console.h> |
| #include <cpu/amd/msr.h> |
| #include <device/pci_ops.h> |
| #include <stdint.h> |
| #include <northbridge/amd/amdht/AsPsDefs.h> |
| #include <stdlib.h> |
| |
| static inline void print_debug_fv(const char *str, u32 val) |
| { |
| #if CONFIG(SET_FIDVID_DEBUG) |
| printk(BIOS_DEBUG, "%s%x\n", str, val); |
| #endif |
| } |
| |
| static inline void print_debug_fv_8(const char *str, u8 val) |
| { |
| #if CONFIG(SET_FIDVID_DEBUG) |
| printk(BIOS_DEBUG, "%s%02x\n", str, val); |
| #endif |
| } |
| |
| static inline void print_debug_fv_64(const char *str, u32 val, u32 val2) |
| { |
| #if CONFIG(SET_FIDVID_DEBUG) |
| printk(BIOS_DEBUG, "%s%x%x\n", str, val, val2); |
| #endif |
| } |
| |
| struct fidvid_st { |
| u32 common_fid; |
| }; |
| |
| static void enable_fid_change(u8 fid) |
| { |
| u32 dword; |
| u32 nodes; |
| pci_devfn_t dev; |
| int i; |
| |
| nodes = get_nodes(); |
| |
| for (i = 0; i < nodes; i++) { |
| dev = NODE_PCI(i, 3); |
| dword = pci_read_config32(dev, 0xd4); |
| dword &= ~0x1F; |
| dword |= (u32) fid & 0x1F; |
| dword |= 1 << 5; // enable |
| pci_write_config32(dev, 0xd4, dword); |
| printk(BIOS_DEBUG, "FID Change Node:%02x, F3xD4: %08x\n", i, |
| dword); |
| } |
| } |
| |
| static void applyBoostFIDOffset(pci_devfn_t dev, uint32_t nodeid) |
| { |
| // BKDG 2.4.2.8 |
| // Fam10h revision E only, but E is apparently not supported yet, therefore untested |
| if ((cpuid_edx(0x80000007) & CPB_MASK) |
| && ((cpuid_ecx(0x80000008) & NC_MASK) == 5) ) { |
| u32 core = get_node_core_id_x().coreid; |
| u32 asymetricBoostThisCore = ((pci_read_config32(dev, 0x10C) >> (core*2))) & 3; |
| msr_t msr = rdmsr(PSTATE_0_MSR); |
| u32 cpuFid = msr.lo & PS_CPU_FID_MASK; |
| cpuFid = cpuFid + asymetricBoostThisCore; |
| msr.lo &= ~PS_CPU_FID_MASK; |
| msr.lo |= cpuFid; |
| wrmsr(PSTATE_0_MSR, msr); |
| } else if (is_fam15h()) { |
| uint32_t dword = pci_read_config32(NODE_PCI(nodeid, 4), 0x15c); |
| uint8_t boost_count = (dword >> 2) & 0x7; |
| if (boost_count > 0) { |
| /* Enable boost */ |
| dword &= ~0x3; |
| dword |= 0x1; |
| pci_write_config32(NODE_PCI(nodeid, 4), 0x15c, dword); |
| } |
| } |
| } |
| |
| static void enableNbPState1(pci_devfn_t dev) |
| { |
| uint64_t cpuRev = mctGetLogicalCPUID(0xFF); |
| if (cpuRev & AMD_FAM10_C3) { |
| u32 nbPState = (pci_read_config32(dev, 0x1F0) & NB_PSTATE_MASK); |
| if ( nbPState){ |
| u32 nbVid1 = (pci_read_config32(dev, 0x1F4) & NB_VID1_MASK) >> NB_VID1_SHIFT; |
| u32 i; |
| for (i = nbPState; i < NM_PS_REG; i++) { |
| msr_t msr = rdmsr(PSTATE_0_MSR + i); |
| if (msr.hi & PS_EN_MASK ) { |
| msr.hi |= NB_DID_M_ON; |
| msr.lo &= NB_VID_MASK_OFF; |
| msr.lo |= ( nbVid1 << NB_VID_POS); |
| wrmsr(PSTATE_0_MSR + i, msr); |
| } |
| } |
| } |
| } |
| } |
| |
| static u8 setPStateMaxVal(pci_devfn_t dev) |
| { |
| u8 i, maxpstate=0; |
| for (i = 0; i < NM_PS_REG; i++) { |
| msr_t msr = rdmsr(PSTATE_0_MSR + i); |
| if (msr.hi & PS_IDD_VALUE_MASK) { |
| msr.hi |= PS_EN_MASK; |
| wrmsr(PSTATE_0_MSR + i, msr); |
| } |
| if (msr.hi & PS_EN_MASK) { |
| maxpstate = i; |
| } |
| } |
| //FIXME: CPTC2 and HTC_REG should get max per node, not per core ? |
| u32 reg = pci_read_config32(dev, CPTC2); |
| reg &= PS_MAX_VAL_MASK; |
| reg |= (maxpstate << PS_MAX_VAL_POS); |
| pci_write_config32(dev, CPTC2,reg); |
| return maxpstate; |
| } |
| |
| static void dualPlaneOnly(pci_devfn_t dev) |
| { |
| // BKDG 2.4.2.7 |
| |
| uint64_t cpuRev = mctGetLogicalCPUID(0xFF); |
| if ((mctGetProcessorPackageType() == AMD_PKGTYPE_AM3_2r2) |
| && (cpuRev & (AMD_DR_Cx | AMD_DR_Ex))) { |
| if ((pci_read_config32(dev, 0x1FC) & DUAL_PLANE_ONLY_MASK) |
| && (pci_read_config32(dev, 0xA0) & PVI_MODE)) { |
| if (cpuid_edx(CPUID_EXT_PM) & CPB_MASK) { |
| // revision E only, but E is apparently not supported yet, therefore untested |
| msr_t minPstate = rdmsr(PSTATE_1_MSR); |
| wrmsr(PSTATE_1_MSR, rdmsr(PSTATE_4_MSR)); |
| wrmsr(PSTATE_4_MSR, minPstate); |
| } else { |
| msr_t msr; |
| msr.lo=0; msr.hi=0; |
| wrmsr(PSTATE_0_MSR, rdmsr(PSTATE_4_MSR)); |
| wrmsr(PSTATE_4_MSR, msr); |
| } |
| |
| //FIXME: CPTC2 and HTC_REG should get max per node, not per core ? |
| u8 maxpstate = setPStateMaxVal(dev); |
| |
| u32 reg = pci_read_config32(dev, HTC_REG); |
| reg &= HTC_PS_LMT_MASK; |
| reg |= (maxpstate << PS_LIMIT_POS); |
| pci_write_config32(dev, HTC_REG,reg); |
| } |
| } |
| } |
| |
| static int vidTo100uV(u8 vid) |
| { |
| // returns voltage corresponding to vid in tenths of mV, i.e. hundreds of uV |
| // BKDG #31116 rev 3.48 2.4.1.6 |
| int voltage; |
| if (vid >= 0x7c) { |
| voltage = 0; |
| } else { |
| voltage = (15500 - (125*vid)); |
| } |
| return voltage; |
| } |
| |
| static void setVSRamp(pci_devfn_t dev) |
| { |
| /* BKDG r31116 2010-04-22 2.4.1.7 step b F3xD8[VSRampTime] |
| * If this field accepts 8 values between 10 and 500 us why |
| * does page 324 say "BIOS should set this field to 001b." |
| * (20 us) ? |
| * Shouldn't it depend on the voltage regulators, mainboard |
| * or something ? |
| */ |
| u32 dword; |
| dword = pci_read_config32(dev, 0xd8); |
| dword &= VSRAMP_MASK; |
| dword |= VSRAMP_VALUE; |
| pci_write_config32(dev, 0xd8, dword); |
| } |
| |
| static void recalculateVsSlamTimeSettingOnCorePre(pci_devfn_t dev) |
| { |
| u8 pviModeFlag; |
| u8 highVoltageVid, lowVoltageVid, bValue; |
| u16 minimumSlamTime; |
| u16 vSlamTimes[7] = { 1000, 2000, 3000, 4000, 6000, 10000, 20000 }; /* Reg settings scaled by 100 */ |
| u32 dtemp; |
| msr_t msr; |
| |
| /* This function calculates the VsSlamTime using the range of possible |
| * voltages instead of a hardcoded 200us. |
| * Note: his function is called only from prep_fid_change, |
| * and that from init_cpus.c finalize_node_setup() |
| * (after set AMD MSRs and init ht ) |
| */ |
| |
| /* BKDG r31116 2010-04-22 2.4.1.7 step b F3xD8[VSSlamTime] */ |
| /* Calculate Slam Time |
| * Vslam = (mobileCPU?0.2:0.4)us/mV * (Vp0 - (lowest out of Vpmin or Valt)) mV |
| * In our case, we will scale the values by 100 to avoid |
| * decimals. |
| */ |
| |
| /* Determine if this is a PVI or SVI system */ |
| if (is_fam15h()) { |
| pviModeFlag = 0; |
| } else { |
| dtemp = pci_read_config32(dev, 0xa0); |
| |
| if (dtemp & PVI_MODE) |
| pviModeFlag = 1; |
| else |
| pviModeFlag = 0; |
| } |
| |
| /* Get P0's voltage */ |
| /* MSRC001_00[68:64] are not programmed yet when called from |
| prep_fid_change, one might use F4x1[F0:E0] instead, but |
| theoretically MSRC001_00[68:64] are equal to them after |
| reset. */ |
| msr = rdmsr(PSTATE_0_MSR); |
| highVoltageVid = (u8) ((msr.lo >> PS_CPU_VID_SHFT) & 0x7F); |
| if (!(msr.hi & 0x80000000)) { |
| printk(BIOS_ERR,"P-state info in MSRC001_0064 is invalid !!!\n"); |
| highVoltageVid = (u8) ((pci_read_config32(dev, 0x1E0) |
| >> PS_CPU_VID_SHFT) & 0x7F); |
| } |
| |
| /* If SVI, we only care about CPU VID. |
| * If PVI, determine the higher voltage b/t NB and CPU |
| */ |
| if (pviModeFlag) { |
| bValue = (u8) ((msr.lo >> PS_NB_VID_SHFT) & 0x7F); |
| if (highVoltageVid > bValue) |
| highVoltageVid = bValue; |
| } |
| |
| /* Get PSmax's index */ |
| msr = rdmsr(PS_LIM_REG); |
| bValue = (u8) ((msr.lo >> PS_MAX_VAL_SHFT) & BIT_MASK_3); |
| |
| /* Get PSmax's VID */ |
| msr = rdmsr(PSTATE_0_MSR + bValue); |
| lowVoltageVid = (u8) ((msr.lo >> PS_CPU_VID_SHFT) & 0x7F); |
| if (!(msr.hi & 0x80000000)) { |
| printk(BIOS_ERR, "P-state info in MSR%8x is invalid !!!\n", |
| PSTATE_0_MSR + bValue); |
| lowVoltageVid = (u8) ((pci_read_config32(dev, 0x1E0+(bValue*4)) |
| >> PS_CPU_VID_SHFT) & 0x7F); |
| } |
| |
| /* If SVI, we only care about CPU VID. |
| * If PVI, determine the higher voltage b/t NB and CPU |
| * BKDG 2.4.1.7 (a) |
| */ |
| if (pviModeFlag) { |
| bValue = (u8) ((msr.lo >> PS_NB_VID_SHFT) & 0x7F); |
| if (lowVoltageVid > bValue) |
| lowVoltageVid = bValue; |
| } |
| |
| /* Get AltVID */ |
| dtemp = pci_read_config32(dev, 0xdc); |
| bValue = (u8) (dtemp & BIT_MASK_7); |
| |
| /* Use the VID with the lowest voltage (higher VID) */ |
| if (lowVoltageVid < bValue) |
| lowVoltageVid = bValue; |
| |
| u8 mobileFlag = get_platform_type() & AMD_PTYPE_MOB; |
| minimumSlamTime = (mobileFlag?2:4) * (vidTo100uV(highVoltageVid) - vidTo100uV(lowVoltageVid)); /* * 0.01 us */ |
| |
| |
| /* Now round up to nearest register setting. |
| * Note that if we don't find a value, we |
| * will fall through to a value of 7 |
| */ |
| for (bValue = 0; bValue < 7; bValue++) { |
| if (minimumSlamTime <= vSlamTimes[bValue]) |
| break; |
| } |
| |
| /* Apply the value */ |
| dtemp = pci_read_config32(dev, 0xD8); |
| dtemp &= VSSLAM_MASK; |
| dtemp |= bValue; |
| pci_write_config32(dev, 0xd8, dtemp); |
| } |
| |
| static u32 nb_clk_did(uint8_t node, uint64_t cpuRev, uint8_t procPkg) { |
| uint8_t link0isGen3 = 0; |
| uint8_t offset; |
| if (AMD_CpuFindCapability(node, 0, &offset)) { |
| link0isGen3 = (AMD_checkLinkType(node, offset) & HTPHY_LINKTYPE_HT3 ); |
| } |
| /* FIXME: NB_CLKDID should be 101b for AMD_DA_C2 in package |
| S1g3 in link Gen3 mode, but I don't know how to tell |
| package S1g3 from S1g4 */ |
| if ((cpuRev & AMD_DA_C2) && (procPkg & AMD_PKGTYPE_S1gX) |
| && link0isGen3) { |
| return 5; /* divide clk by 128*/ |
| } else { |
| return 4; /* divide clk by 16 */ |
| } |
| } |
| |
| |
| static u32 power_up_down(int node, u8 procPkg) { |
| uint32_t dword=0; |
| /* from CPU rev guide #41322 rev 3.74 June 2010 Table 26 */ |
| u8 singleLinkFlag = ((procPkg == AMD_PKGTYPE_AM3_2r2) |
| || (procPkg == AMD_PKGTYPE_S1gX) |
| || (procPkg == AMD_PKGTYPE_ASB2)); |
| |
| if (singleLinkFlag) { |
| /* |
| * PowerStepUp=01000b - 50nS |
| * PowerStepDown=01000b - 50ns |
| */ |
| dword |= PW_STP_UP50 | PW_STP_DN50; |
| } else { |
| uint32_t dispRefModeEn = (pci_read_config32(NODE_PCI(node,0),0x68) >> 24) & 1; |
| uint32_t isocEn = 0; |
| int j; |
| for (j=0; (j<4) && (!isocEn); j++ ) { |
| u8 offset; |
| if (AMD_CpuFindCapability(node, j, &offset)) { |
| isocEn = (pci_read_config32(NODE_PCI(node,0),offset+4) >>12) & 1; |
| } |
| } |
| |
| if (is_fam15h()) { |
| /* Family 15h always uses 100ns for multilink processors */ |
| dword |= PW_STP_UP100 | PW_STP_DN100; |
| } else if (dispRefModeEn || isocEn) { |
| dword |= PW_STP_UP50 | PW_STP_DN50; |
| } else { |
| /* get number of cores for PowerStepUp & PowerStepDown in server |
| * 1 core - 400nS - 0000b |
| * 2 cores - 200nS - 0010b |
| * 3 cores - 133nS -> 100nS - 0011b |
| * 4 cores - 100nS - 0011b |
| */ |
| switch (get_core_num_in_bsp(node)) { |
| case 0: |
| dword |= PW_STP_UP400 | PW_STP_DN400; |
| break; |
| case 1: |
| case 2: |
| dword |= PW_STP_UP200 | PW_STP_DN200; |
| break; |
| case 3: |
| dword |= PW_STP_UP100 | PW_STP_DN100; |
| break; |
| default: |
| dword |= PW_STP_UP100 | PW_STP_DN100; |
| break; |
| } |
| } |
| } |
| |
| return dword; |
| } |
| |
| static void config_clk_power_ctrl_reg0(uint8_t node, uint64_t cpuRev, uint8_t procPkg) { |
| |
| pci_devfn_t dev = NODE_PCI(node, 3); |
| |
| /* Program fields in Clock Power/Control register0 (F3xD4) */ |
| |
| /* set F3xD4 Clock Power/Timing Control 0 Register |
| * NbClkDidApplyAll=1b |
| * NbClkDid=100b or 101b |
| * PowerStepUp= "platform dependent" |
| * PowerStepDown= "platform dependent" |
| * LinkPllLink=01b |
| * ClkRampHystCtl=HW default |
| * ClkRampHystSel=1111b |
| */ |
| uint32_t dword= pci_read_config32(dev, 0xd4); |
| dword &= CPTC0_MASK; |
| dword |= NB_CLKDID_ALL | LNK_PLL_LOCK | CLK_RAMP_HYST_SEL_VAL; |
| dword |= (nb_clk_did(node,cpuRev,procPkg) << NB_CLKDID_SHIFT); |
| |
| dword |= power_up_down(node, procPkg); |
| |
| pci_write_config32(dev, 0xd4, dword); |
| |
| } |
| |
| static void config_power_ctrl_misc_reg(pci_devfn_t dev, uint64_t cpuRev, |
| uint8_t procPkg) |
| { |
| /* check PVI/SVI */ |
| uint32_t dword = pci_read_config32(dev, 0xa0); |
| |
| /* BKDG r31116 2010-04-22 2.4.1.7 step b F3xA0[VSSlamVidMod] */ |
| /* PllLockTime and PsiVidEn set in ruleset in defaults.h */ |
| if (dword & PVI_MODE) { /* PVI */ |
| /* set slamVidMode to 0 for PVI */ |
| dword &= VID_SLAM_OFF; |
| } else { /* SVI */ |
| /* set slamVidMode to 1 for SVI */ |
| dword |= VID_SLAM_ON; |
| } |
| /* set the rest of A0 since we're at it... */ |
| |
| if (cpuRev & (AMD_DA_Cx | AMD_RB_C3 )) { |
| dword |= NB_PSTATE_FORCE_ON; |
| } // else should we clear it ? |
| |
| |
| if ((procPkg == AMD_PKGTYPE_G34) || (procPkg == AMD_PKGTYPE_C32) ) { |
| dword |= BP_INS_TRI_EN_ON; |
| } |
| |
| /* TODO: look into C1E state and F3xA0[IdleExitEn]*/ |
| #if 0 |
| if (cpuRev & AMD_FAM10_C3) { |
| dword |= SVI_HIGH_FREQ_ON; |
| } |
| #endif |
| pci_write_config32(dev, 0xa0, dword); |
| } |
| |
| static void config_nb_syn_ptr_adj(pci_devfn_t dev, uint64_t cpuRev) |
| { |
| /* Note the following settings are additional from the ported |
| * function setFidVidRegs() |
| */ |
| /* adjust FIFO between nb and core clocks to max allowed |
| values (min latency) */ |
| uint32_t nbPstate = pci_read_config32(dev,0x1f0) & NB_PSTATE_MASK; |
| uint8_t nbSynPtrAdj; |
| if ((cpuRev & (AMD_DR_Bx | AMD_DA_Cx | AMD_FAM15_ALL) ) |
| || ((cpuRev & AMD_RB_C3) && (nbPstate != 0))) { |
| nbSynPtrAdj = 5; |
| } else { |
| nbSynPtrAdj = 6; |
| } |
| |
| uint32_t dword = pci_read_config32(dev, 0xdc); |
| dword &= ~NB_SYN_PTR_ADJ_MASK; |
| dword |= nbSynPtrAdj << NB_SYN_PTR_ADJ_POS; |
| /* NbsynPtrAdj set to 5 or 6 per BKDG (needs reset) */ |
| pci_write_config32(dev, 0xdc, dword); |
| } |
| |
| static void config_acpi_pwr_state_ctrl_regs(pci_devfn_t dev, uint64_t cpuRev, |
| uint8_t procPkg) |
| { |
| if (is_fam15h()) { |
| /* Family 15h BKDG Rev. 3.14 D18F3x80 recommended settings */ |
| pci_write_config32(dev, 0x80, 0xe20be281); |
| |
| /* Family 15h BKDG Rev. 3.14 D18F3x84 recommended settings */ |
| pci_write_config32(dev, 0x84, 0x01e200e2); |
| } else { |
| /* step 1, chapter 2.4.2.6 of AMD Fam 10 BKDG #31116 Rev 3.48 22.4.2010 */ |
| uint32_t dword; |
| uint32_t c1= 1; |
| if (cpuRev & (AMD_DR_Bx)) { |
| // will coreboot ever enable cache scrubbing ? |
| // if it does, will it be enough to check the current state |
| // or should we configure for what we'll set up later ? |
| dword = pci_read_config32(dev, 0x58); |
| uint32_t scrubbingCache = dword & |
| ( (0x1F << 16) // DCacheScrub |
| | (0x1F << 8) ); // L2Scrub |
| if (scrubbingCache) { |
| c1 = 0x80; |
| } else { |
| c1 = 0xA0; |
| } |
| } else { // rev C or later |
| // same doubt as cache scrubbing: ok to check current state ? |
| dword = pci_read_config32(dev, 0xdc); |
| uint32_t cacheFlushOnHalt = dword & (7 << 16); |
| if (!cacheFlushOnHalt) { |
| c1 = 0x80; |
| } |
| } |
| dword = (c1 << 24) | (0xE641E6); |
| pci_write_config32(dev, 0x84, dword); |
| |
| /* FIXME: BKDG Table 100 says if the link is at a Gen1 |
| * frequency and the chipset does not support a 10us minimum LDTSTOP |
| * assertion time, then { If ASB2 && SVI then smaf001 = F6h else |
| * smaf001=87h. } else ... I hardly know what it means or how to check |
| * it from here, so I bluntly assume it is false and code here the else, |
| * which is easier |
| */ |
| |
| uint32_t smaf001 = 0xE6; |
| if (cpuRev & AMD_DR_Bx ) { |
| smaf001 = 0xA6; |
| } else { |
| #if 0 |
| if (cpuRev & (AMD_RB_C3 | AMD_DA_C3)) { |
| smaf001 = 0xF6; |
| } |
| #endif |
| } |
| uint32_t fidvidChange = 0; |
| if (((cpuRev & AMD_DA_Cx) && (procPkg & AMD_PKGTYPE_S1gX)) |
| || (cpuRev & AMD_RB_C3) ) { |
| fidvidChange=0x0B; |
| } |
| dword = (0xE6 << 24) | (fidvidChange << 16) |
| | (smaf001 << 8) | 0x81; |
| pci_write_config32(dev, 0x80, dword); |
| } |
| } |
| |
| void prep_fid_change(void) |
| { |
| u32 dword; |
| u32 nodes; |
| pci_devfn_t dev; |
| int i; |
| |
| /* This needs to be run before any Pstate changes are requested */ |
| |
| nodes = get_nodes(); |
| |
| for (i = 0; i < nodes; i++) { |
| printk(BIOS_DEBUG, "Prep FID/VID Node:%02x\n", i); |
| dev = NODE_PCI(i, 3); |
| uint64_t cpuRev = mctGetLogicalCPUID(0xFF); |
| u8 procPkg = mctGetProcessorPackageType(); |
| |
| setVSRamp(dev); |
| /* BKDG r31116 2010-04-22 2.4.1.7 step b F3xD8[VSSlamTime] */ |
| /* Figure out the value for VsSlamTime and program it */ |
| recalculateVsSlamTimeSettingOnCorePre(dev); |
| |
| config_clk_power_ctrl_reg0(i,cpuRev,procPkg); |
| |
| config_power_ctrl_misc_reg(dev,cpuRev,procPkg); |
| config_nb_syn_ptr_adj(dev,cpuRev); |
| |
| config_acpi_pwr_state_ctrl_regs(dev,cpuRev,procPkg); |
| |
| dword = pci_read_config32(dev, 0x80); |
| printk(BIOS_DEBUG, " F3x80: %08x\n", dword); |
| dword = pci_read_config32(dev, 0x84); |
| printk(BIOS_DEBUG, " F3x84: %08x\n", dword); |
| dword = pci_read_config32(dev, 0xd4); |
| printk(BIOS_DEBUG, " F3xD4: %08x\n", dword); |
| dword = pci_read_config32(dev, 0xd8); |
| printk(BIOS_DEBUG, " F3xD8: %08x\n", dword); |
| dword = pci_read_config32(dev, 0xdc); |
| printk(BIOS_DEBUG, " F3xDC: %08x\n", dword); |
| } |
| } |
| |
| static void waitCurrentPstate(u32 target_pstate) { |
| msr_t initial_msr = rdmsr(TSC_MSR); |
| msr_t pstate_msr = rdmsr(PS_STS_REG); |
| msr_t tsc_msr; |
| u8 timedout; |
| |
| /* paranoia ? I fear when we run fixPsNbVidBeforeWR we can enter a |
| * P1 that is a copy of P0, therefore has the same NB DID but the |
| * TSC will count twice per tick, so we have to wait for twice the |
| * count to achieve the desired timeout. But I'm likely to |
| * misunderstand this... |
| */ |
| u32 corrected_timeout = ((pstate_msr.lo==1) |
| && (!(rdmsr(PSTATE_1_MSR).lo & NB_DID_M_ON))) ? |
| WAIT_PSTATE_TIMEOUT*2 : WAIT_PSTATE_TIMEOUT; |
| msr_t timeout; |
| |
| timeout.lo = initial_msr.lo + corrected_timeout; |
| timeout.hi = initial_msr.hi; |
| if ( (((u32)0xffffffff) - initial_msr.lo) < corrected_timeout ) { |
| timeout.hi++; |
| } |
| |
| // assuming TSC ticks at 1.25 ns per tick (800 MHz) |
| do { |
| pstate_msr = rdmsr(PS_STS_REG); |
| tsc_msr = rdmsr(TSC_MSR); |
| timedout = (tsc_msr.hi > timeout.hi) |
| || ((tsc_msr.hi == timeout.hi) && (tsc_msr.lo > timeout.lo )); |
| } while ( (pstate_msr.lo != target_pstate) && (! timedout) ); |
| |
| if (pstate_msr.lo != target_pstate) { |
| msr_t limit_msr = rdmsr(PS_LIM_REG); |
| printk(BIOS_ERR, "*** APIC ID %02x: timed out waiting for P-state %01x. Current P-state %01x P-state current limit MSRC001_0061=%08x %08x\n", |
| cpuid_ebx(0x00000001) >> 24, target_pstate, pstate_msr.lo, limit_msr.hi, limit_msr.lo); |
| |
| do { // should we just go on instead ? |
| pstate_msr = rdmsr(PS_STS_REG); |
| } while (pstate_msr.lo != target_pstate); |
| } |
| } |
| |
| static void set_pstate(u32 nonBoostedPState) { |
| msr_t msr; |
| uint8_t skip_wait; |
| |
| // Transition P0 for calling core. |
| msr = rdmsr(PS_CTL_REG); |
| |
| msr.lo = nonBoostedPState; |
| wrmsr(PS_CTL_REG, msr); |
| |
| if (is_fam15h()) { |
| /* Do not wait for the first (even) set of cores to transition on Family 15h systems */ |
| if ((cpuid_ebx(0x00000001) & 0x01000000)) |
| skip_wait = 0; |
| else |
| skip_wait = 1; |
| } else { |
| skip_wait = 0; |
| } |
| |
| if (!skip_wait) { |
| /* Wait for core to transition to P0 */ |
| waitCurrentPstate(nonBoostedPState); |
| } |
| } |
| |
| static void UpdateSinglePlaneNbVid(void) |
| { |
| u32 nbVid, cpuVid; |
| u8 i; |
| msr_t msr; |
| |
| /* copy higher voltage (lower VID) of NBVID & CPUVID to both */ |
| for (i = 0; i < 5; i++) { |
| msr = rdmsr(PSTATE_0_MSR + i); |
| nbVid = (msr.lo & PS_CPU_VID_M_ON) >> PS_CPU_VID_SHFT; |
| cpuVid = (msr.lo & PS_NB_VID_M_ON) >> PS_NB_VID_SHFT; |
| |
| if (nbVid != cpuVid) { |
| if (nbVid > cpuVid) |
| nbVid = cpuVid; |
| |
| msr.lo = msr.lo & PS_BOTH_VID_OFF; |
| msr.lo = msr.lo | (u32) ((nbVid) << PS_NB_VID_SHFT); |
| msr.lo = msr.lo | (u32) ((nbVid) << PS_CPU_VID_SHFT); |
| wrmsr(PSTATE_0_MSR + i, msr); |
| } |
| } |
| } |
| |
| static void fixPsNbVidBeforeWR(u32 newNbVid, u32 coreid, u32 dev, u8 pviMode) |
| { |
| msr_t msr; |
| u8 startup_pstate; |
| |
| /* This function sets NbVid before the warm reset. |
| * Get StartupPstate from MSRC001_0071. |
| * Read Pstate register pointed by [StartupPstate]. |
| * and copy its content to P0 and P1 registers. |
| * Copy newNbVid to P0[NbVid]. |
| * transition to P1 on all cores, |
| * then transition to P0 on core 0. |
| * Wait for MSRC001_0063[CurPstate] = 000b on core 0. |
| * see BKDG rev 3.48 2.4.2.9.1 BIOS NB COF and VID Configuration |
| * for SVI and Single-Plane PVI Systems |
| */ |
| |
| msr = rdmsr(MSR_COFVID_STS); |
| startup_pstate = (msr.hi >> (32 - 32)) & 0x07; |
| |
| /* Copy startup pstate to P1 and P0 MSRs. Set the maxvid for |
| * this node in P0. Then transition to P1 for corex and P0 |
| * for core0. These setting will be cleared by the warm reset |
| */ |
| msr = rdmsr(PSTATE_0_MSR + startup_pstate); |
| wrmsr(PSTATE_1_MSR, msr); |
| wrmsr(PSTATE_0_MSR, msr); |
| |
| /* missing step 2 from BDKG , F3xDC[PstateMaxVal] = |
| * max(1,F3xDC[PstateMaxVal] ) because it would take |
| * synchronization between cores and we don't think |
| * PstatMaxVal is going to be 0 on cold reset anyway ? |
| */ |
| if (!(pci_read_config32(dev, 0xdc) & (~PS_MAX_VAL_MASK))) { |
| printk(BIOS_ERR,"F3xDC[PstateMaxVal] is zero. Northbridge voltage setting will fail. fixPsNbVidBeforeWR in fidvid.c needs fixing. See AMD # 31116 rev 3.48 BKDG 2.4.2.9.1\n"); |
| }; |
| |
| msr.lo &= ~0xFE000000; // clear nbvid |
| msr.lo |= (newNbVid << 25); |
| wrmsr(PSTATE_0_MSR, msr); |
| |
| if (pviMode) { /* single plane*/ |
| UpdateSinglePlaneNbVid(); |
| } |
| |
| // Transition to P1 for all APs and P0 for core0. |
| set_pstate(1); |
| |
| if (coreid == 0) { |
| set_pstate(0); |
| } |
| |
| /* missing step 7 (restore PstateMax to 0 if needed) because |
| * we skipped step 2 |
| */ |
| |
| } |
| |
| static u32 needs_NB_COF_VID_update(void) |
| { |
| u8 nb_cof_vid_update; |
| u8 nodes; |
| u8 i; |
| |
| if (is_fam15h()) |
| return 0; |
| |
| /* If any node has nb_cof_vid_update set all nodes need an update. */ |
| nodes = get_nodes(); |
| nb_cof_vid_update = 0; |
| for (i = 0; i < nodes; i++) { |
| uint64_t cpuRev = mctGetLogicalCPUID(i); |
| u32 nbCofVidUpdateDefined = (cpuRev & (AMD_FAM10_LT_D)); |
| if (nbCofVidUpdateDefined |
| && (pci_read_config32(NODE_PCI(i, 3), 0x1FC) |
| & NB_COF_VID_UPDATE_MASK)) { |
| nb_cof_vid_update = 1; |
| break; |
| } |
| } |
| return nb_cof_vid_update; |
| } |
| |
| static u32 init_fidvid_core(u32 nodeid, u32 coreid) |
| { |
| pci_devfn_t dev; |
| u32 vid_max; |
| u32 fid_max = 0; |
| u8 nb_cof_vid_update = needs_NB_COF_VID_update(); |
| u8 pvimode; |
| u32 reg1fc; |
| |
| /* Steps 1-6 of BIOS NB COF and VID Configuration |
| * for SVI and Single-Plane PVI Systems. BKDG 2.4.2.9 #31116 rev 3.48 |
| */ |
| dev = NODE_PCI(nodeid, 3); |
| if (is_fam15h()) |
| pvimode = 0; |
| else |
| pvimode = pci_read_config32(dev, PW_CTL_MISC) & PVI_MODE; |
| reg1fc = pci_read_config32(dev, 0x1FC); |
| |
| if (nb_cof_vid_update) { |
| vid_max = (reg1fc & SINGLE_PLANE_NB_VID_MASK ) >> SINGLE_PLANE_NB_VID_SHIFT; |
| fid_max = (reg1fc & SINGLE_PLANE_NB_FID_MASK ) >> SINGLE_PLANE_NB_FID_SHIFT; |
| |
| if (!pvimode) { /* SVI, dual power plane */ |
| vid_max = vid_max - ((reg1fc & DUAL_PLANE_NB_VID_OFF_MASK ) >> DUAL_PLANE_NB_VID_SHIFT ); |
| fid_max = fid_max + ((reg1fc & DUAL_PLANE_NB_FID_OFF_MASK ) >> DUAL_PLANE_NB_FID_SHIFT ); |
| } |
| /* write newNbVid to P-state Reg's NbVid always if NbVidUpdatedAll=1 */ |
| fixPsNbVidBeforeWR(vid_max, coreid, dev, pvimode); |
| |
| /* fid setup is handled by the BSP at the end. */ |
| |
| } else { /* ! nb_cof_vid_update */ |
| /* Use max values */ |
| if (pvimode) |
| UpdateSinglePlaneNbVid(); |
| } |
| |
| return ((nb_cof_vid_update << 16) | (fid_max << 8)); |
| |
| } |
| |
| static void init_fidvid_ap(u32 apicid, u32 nodeid, u32 coreid) |
| { |
| u32 send; |
| |
| printk(BIOS_DEBUG, "FIDVID on AP: %02x\n", apicid); |
| |
| send = init_fidvid_core(nodeid, coreid); |
| send |= (apicid << 24); // ap apicid |
| |
| // Send signal to BSP about this AP max fid |
| // This also indicates this AP is ready for warm reset (if required). |
| lapic_write(LAPIC_MSG_REG, send | F10_APSTATE_RESET); |
| } |
| |
| static u32 calc_common_fid(u32 fid_packed, u32 fid_packed_new) |
| { |
| u32 fidmax; |
| u32 fidmax_new; |
| |
| fidmax = (fid_packed >> 8) & 0xFF; |
| |
| fidmax_new = (fid_packed_new >> 8) & 0xFF; |
| |
| if (fidmax > fidmax_new) { |
| fidmax = fidmax_new; |
| } |
| |
| fid_packed &= 0xFF << 16; |
| fid_packed |= (fidmax << 8); |
| fid_packed |= fid_packed_new & (0xFF << 16); // set nb_cof_vid_update |
| |
| return fid_packed; |
| } |
| |
| static void init_fidvid_bsp_stage1(u32 ap_apicid, void *gp) |
| { |
| u32 readback = 0; |
| u32 timeout = 1; |
| |
| struct fidvid_st *fvp = gp; |
| int loop; |
| |
| print_debug_fv("Wait for AP stage 1: ap_apicid = ", ap_apicid); |
| |
| loop = 100000; |
| while (--loop > 0) { |
| if (lapic_remote_read(ap_apicid, LAPIC_MSG_REG, &readback) != 0) |
| continue; |
| if (((readback & 0x3f) == F10_APSTATE_RESET) |
| || (is_fam15h() && ((readback & 0x3f) == F10_APSTATE_ASLEEP))) { |
| timeout = 0; |
| break; /* target ap is in stage 1 */ |
| } |
| } |
| |
| if (timeout) { |
| printk(BIOS_DEBUG, "%s: timed out reading from ap %02x\n", |
| __func__, ap_apicid); |
| return; |
| } |
| |
| print_debug_fv("\treadback = ", readback); |
| |
| fvp->common_fid = calc_common_fid(fvp->common_fid, readback); |
| |
| print_debug_fv("\tcommon_fid(packed) = ", fvp->common_fid); |
| |
| } |
| |
| static void fixPsNbVidAfterWR(u32 newNbVid, u8 NbVidUpdatedAll,u8 pviMode) |
| { |
| msr_t msr; |
| u8 i; |
| u8 StartupPstate; |
| |
| /* BKDG 2.4.2.9.1 11-12 |
| * This function copies newNbVid to NbVid bits in P-state |
| * Registers[4:0] if its NbDid bit=0, and IddValue!=0 in case of |
| * NbVidUpdatedAll =0 or copies newNbVid to NbVid bits in |
| * P-state Registers[4:0] if its IddValue!=0 in case of |
| * NbVidUpdatedAll=1. Then transition to StartPstate. |
| */ |
| |
| /* write newNbVid to P-state Reg's NbVid if its NbDid=0 */ |
| for (i = 0; i < 5; i++) { |
| msr = rdmsr(PSTATE_0_MSR + i); |
| /* NbDid (bit 22 of P-state Reg) == 0 or NbVidUpdatedAll = 1 */ |
| if ( (msr.hi & PS_IDD_VALUE_MASK) |
| && (msr.hi & PS_EN_MASK) |
| &&(((msr.lo & PS_NB_DID_MASK) == 0) || NbVidUpdatedAll)) { |
| msr.lo &= PS_NB_VID_M_OFF; |
| msr.lo |= (newNbVid & 0x7F) << PS_NB_VID_SHFT; |
| wrmsr(PSTATE_0_MSR + i, msr); |
| } |
| } |
| |
| /* Not documented. Would overwrite Nb_Vids just copied |
| * should we just update cpu_vid or nothing at all ? |
| */ |
| if (pviMode) { //single plane |
| UpdateSinglePlaneNbVid(); |
| } |
| /* For each core in the system, transition all cores to StartupPstate */ |
| msr = rdmsr(MSR_COFVID_STS); |
| StartupPstate = msr.hi & 0x07; |
| |
| /* Set and wait for StartupPstate to set. */ |
| set_pstate(StartupPstate); |
| |
| } |
| |
| static void finalPstateChange(void) |
| { |
| /* Enable P0 on all cores for best performance. |
| * Linux can slow them down later if need be. |
| * It is safe since they will be in C1 halt |
| * most of the time anyway. |
| */ |
| set_pstate(0); |
| } |
| |
| void init_fidvid_stage2(u32 apicid, u32 nodeid) |
| { |
| msr_t msr; |
| pci_devfn_t dev; |
| u32 reg1fc; |
| u32 dtemp; |
| u32 nbvid; |
| u8 nb_cof_vid_update = needs_NB_COF_VID_update(); |
| u8 NbVidUpdateAll; |
| u8 pvimode; |
| |
| /* After warm reset finish the fid/vid setup for all cores. */ |
| |
| /* If any node has nb_cof_vid_update set all nodes need an update. */ |
| |
| dev = NODE_PCI(nodeid, 3); |
| if (is_fam15h()) |
| pvimode = 0; |
| else |
| pvimode = (pci_read_config32(dev, 0xA0) >> 8) & 1; |
| reg1fc = pci_read_config32(dev, 0x1FC); |
| nbvid = (reg1fc >> 7) & 0x7F; |
| NbVidUpdateAll = (reg1fc >> 1) & 1; |
| |
| if (nb_cof_vid_update) { |
| if (!pvimode) { /* SVI */ |
| nbvid = nbvid - ((reg1fc >> 17) & 0x1F); |
| } |
| /* write newNbVid to P-state Reg's NbVid if its NbDid=0 */ |
| fixPsNbVidAfterWR(nbvid, NbVidUpdateAll,pvimode); |
| } else { /* !nb_cof_vid_update */ |
| if (pvimode) |
| UpdateSinglePlaneNbVid(); |
| } |
| dtemp = pci_read_config32(dev, 0xA0); |
| dtemp &= PLLLOCK_OFF; |
| dtemp |= PLLLOCK_DFT_L; |
| pci_write_config32(dev, 0xA0, dtemp); |
| |
| dualPlaneOnly(dev); |
| applyBoostFIDOffset(dev, nodeid); |
| enableNbPState1(dev); |
| |
| finalPstateChange(); |
| |
| if (!is_fam15h()) { |
| /* Set TSC to tick at the P0 ndfid rate */ |
| msr = rdmsr(HWCR_MSR); |
| msr.lo |= 1 << 24; |
| wrmsr(HWCR_MSR, msr); |
| } |
| } |
| |
| |
| #if CONFIG(SET_FIDVID_STORE_AP_APICID_AT_FIRST) |
| struct ap_apicid_st { |
| u32 num; |
| // it could use 256 bytes for 64 node quad core system |
| u8 apicid[NODE_NUMS * 4]; |
| }; |
| |
| static void store_ap_apicid(unsigned int ap_apicid, void *gp) |
| { |
| struct ap_apicid_st *p = gp; |
| |
| p->apicid[p->num++] = ap_apicid; |
| |
| } |
| #endif |
| |
| |
| int init_fidvid_bsp(u32 bsp_apicid, u32 nodes) |
| { |
| #if CONFIG(SET_FIDVID_STORE_AP_APICID_AT_FIRST) |
| struct ap_apicid_st ap_apicidx; |
| u32 i; |
| #endif |
| struct fidvid_st fv; |
| |
| printk(BIOS_DEBUG, "FIDVID on BSP, APIC_id: %02x\n", bsp_apicid); |
| |
| /* Steps 1-6 of BIOS NB COF and VID Configuration |
| * for SVI and Single-Plane PVI Systems. |
| */ |
| fv.common_fid = init_fidvid_core(0, 0); |
| |
| print_debug_fv("BSP fid = ", fv.common_fid); |
| |
| #if CONFIG(SET_FIDVID_STORE_AP_APICID_AT_FIRST) && \ |
| !CONFIG(SET_FIDVID_CORE0_ONLY) |
| /* For all APs (We know the APIC ID of all APs even when the APIC ID |
| is lifted) remote read from AP LAPIC_MSG_REG about max fid. |
| Then calculate the common max fid that can be used for all |
| APs and BSP */ |
| ap_apicidx.num = 0; |
| |
| for_each_ap(bsp_apicid, CONFIG_SET_FIDVID_CORE_RANGE, -1, store_ap_apicid, &ap_apicidx); |
| |
| for (i = 0; i < ap_apicidx.num; i++) { |
| init_fidvid_bsp_stage1(ap_apicidx.apicid[i], &fv); |
| } |
| #else |
| for_each_ap(bsp_apicid, CONFIG(SET_FIDVID_CORE0_ONLY), -1, init_fidvid_bsp_stage1, &fv); |
| #endif |
| |
| print_debug_fv("common_fid = ", fv.common_fid); |
| |
| if (fv.common_fid & (1 << 16)) { /* check nb_cof_vid_update */ |
| |
| // Enable the common fid and other settings. |
| enable_fid_change((fv.common_fid >> 8) & 0x1F); |
| |
| // nbfid change need warm reset, so reset at first |
| return 1; |
| } |
| |
| return 0; // No FID/VID changes. Don't reset |
| } |