diff --git a/src/soc/intel/baytrail/southcluster.c b/src/soc/intel/baytrail/southcluster.c
index dcc48e9..45c588a 100644
--- a/src/soc/intel/baytrail/southcluster.c
+++ b/src/soc/intel/baytrail/southcluster.c
@@ -28,9 +28,8 @@
 #include "chip.h"
 #include <acpi/acpigen.h>
 
-static inline void
-add_mmio_resource(struct device *dev, int i, unsigned long addr,
-		  unsigned long size)
+static inline void add_mmio_resource(struct device *dev, int i, unsigned long addr,
+				     unsigned long size)
 {
 	mmio_resource(dev, i, addr >> 10, size >> 10);
 }
@@ -58,8 +57,7 @@
 		return 0;
 
 	/* Is it entirely contained? */
-	if (base >= LPC_DEFAULT_IO_RANGE_LOWER &&
-	    (base + size) < LPC_DEFAULT_IO_RANGE_UPPER)
+	if (base >= LPC_DEFAULT_IO_RANGE_LOWER && (base + size) < LPC_DEFAULT_IO_RANGE_UPPER)
 		return 1;
 
 	/* This will return not in range for partial overlaps */
@@ -70,8 +68,7 @@
  * Note: this function assumes there is no overlap with the default LPC device's
  * claimed range: LPC_DEFAULT_IO_RANGE_LOWER -> LPC_DEFAULT_IO_RANGE_UPPER.
  */
-static void sc_add_io_resource(struct device *dev, int base, int size,
-			       int index)
+static void sc_add_io_resource(struct device *dev, int base, int size, int index)
 {
 	struct resource *res;
 
@@ -113,11 +110,6 @@
 	sc_add_io_resources(dev);
 }
 
-static void sc_rtc_init(void)
-{
-	cmos_init(rtc_failure());
-}
-
 /*
  * The UART hardware loses power while in suspend. Because of this the kernel
  * can hang because it doesn't re-initialize serial ports it is using for
@@ -176,15 +168,14 @@
 	/* Route SCI to IRQ9 */
 	write32(actl, (read32(actl) & ~SCIS_MASK) | SCIS_IRQ9);
 
-	sc_rtc_init();
+	cmos_init(rtc_failure());
 
 	if (config->disable_slp_x_stretch_sus_fail) {
 		printk(BIOS_DEBUG, "Disabling slp_x stretching.\n");
-		write32(gen_pmcon1,
-			read32(gen_pmcon1) | DIS_SLP_X_STRCH_SUS_UP);
+		write32(gen_pmcon1, read32(gen_pmcon1) | DIS_SLP_X_STRCH_SUS_UP);
+
 	} else {
-		write32(gen_pmcon1,
-			read32(gen_pmcon1) & ~DIS_SLP_X_STRCH_SUS_UP);
+		write32(gen_pmcon1, read32(gen_pmcon1) & ~DIS_SLP_X_STRCH_SUS_UP);
 	}
 
 	if (acpi_is_wakeup_s3())
@@ -200,7 +191,7 @@
 {
 	void *func_dis  = (void *)(PMC_BASE_ADDRESS + FUNC_DIS);
 	void *func_dis2 = (void *)(PMC_BASE_ADDRESS + FUNC_DIS2);
-	uint32_t mask = 0;
+	uint32_t mask  = 0;
 	uint32_t mask2 = 0;
 
 	switch (dev->path.pci.devfn) {
@@ -475,8 +466,7 @@
 
 		/* Ensure memory, io, and bus master are all disabled */
 		reg16 = pci_read_config16(dev, PCI_COMMAND);
-		reg16 &= ~(PCI_COMMAND_MASTER |
-			   PCI_COMMAND_MEMORY | PCI_COMMAND_IO);
+		reg16 &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO);
 		pci_write_config16(dev, PCI_COMMAND, reg16);
 
 		/* Place device in D3Hot */
@@ -522,7 +512,7 @@
 	.read_resources		= sc_read_resources,
 	.set_resources		= pci_dev_set_resources,
 	.acpi_inject_dsdt	= southcluster_inject_dsdt,
-	.write_acpi_tables      = acpi_write_hpet,
+	.write_acpi_tables	= acpi_write_hpet,
 	.init			= sc_init,
 	.enable			= southcluster_enable_dev,
 	.scan_bus		= scan_static_bus,
@@ -546,7 +536,7 @@
 	void *gcs = (void *)(RCBA_BASE_ADDRESS + GCS);
 	void *gen_pmcon2 = (void *)(PMC_BASE_ADDRESS + GEN_PMCON2);
 	void *etr = (void *)(PMC_BASE_ADDRESS + ETR);
-	u8 *spi = (u8 *)SPI_BASE_ADDRESS;
+	uint8_t *spi = (uint8_t *)SPI_BASE_ADDRESS;
 	struct spi_config cfg;
 
 	/* Set the lock enable on the BIOS control register */