google/asuka: Add as a variant of glados
Add google/asuka (Dell Chromebook 13 3380) as a variant of
glados Skylake reference board:
- add asuka-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/asuka, verify correct functionality
Change-Id: I591578fea2514a28c75177835807c3f250904577
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27421
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
diff --git a/src/mainboard/google/glados/variants/asuka/devicetree.cb b/src/mainboard/google/glados/variants/asuka/devicetree.cb
new file mode 100644
index 0000000..cbd8b01
--- /dev/null
+++ b/src/mainboard/google/glados/variants/asuka/devicetree.cb
@@ -0,0 +1,288 @@
+chip soc/intel/skylake
+
+ # Enable deep Sx states
+ register "deep_s3_enable_ac" = "0"
+ register "deep_s3_enable_dc" = "0"
+ register "deep_s5_enable_ac" = "1"
+ register "deep_s5_enable_dc" = "1"
+ register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"
+
+ # GPE configuration
+ # Note that GPE events called out in ASL code rely on this
+ # route. i.e. If this route changes then the affected GPE
+ # offset bits also need to be changed.
+ register "gpe0_dw0" = "GPP_B"
+ register "gpe0_dw1" = "GPP_D"
+ register "gpe0_dw2" = "GPP_E"
+
+ # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
+ register "gen1_dec" = "0x00fc0801"
+ register "gen2_dec" = "0x000c0201"
+
+ # Enable "Intel Speed Shift Technology"
+ register "speed_shift_enable" = "1"
+
+ # Enable DPTF
+ register "dptf_enable" = "1"
+
+ # FSP Configuration
+ register "EnableAzalia" = "1"
+ register "DspEnable" = "1"
+ register "IoBufferOwnership" = "3"
+ register "SmbusEnable" = "1"
+ register "ScsEmmcEnabled" = "1"
+ register "ScsEmmcHs400Enabled" = "1"
+ register "ScsSdCardEnabled" = "0"
+ register "InternalGfx" = "1"
+ register "SkipExtGfxScan" = "1"
+ register "Device4Enable" = "1"
+ register "HeciEnabled" = "0"
+ register "SaGv" = "3"
+ register "SerialIrqConfigSirqEnable" = "1"
+ register "PmConfigSlpS3MinAssert" = "2" # 50ms
+ register "PmConfigSlpS4MinAssert" = "4" # 4s
+ register "PmConfigSlpSusMinAssert" = "3" # 4s
+ register "PmConfigSlpAMinAssert" = "3" # 2s
+ register "PmTimerDisabled" = "1"
+
+ register "pirqa_routing" = "PCH_IRQ11"
+ register "pirqb_routing" = "PCH_IRQ10"
+ register "pirqc_routing" = "PCH_IRQ11"
+ register "pirqd_routing" = "PCH_IRQ11"
+ register "pirqe_routing" = "PCH_IRQ11"
+ register "pirqf_routing" = "PCH_IRQ11"
+ register "pirqg_routing" = "PCH_IRQ11"
+ register "pirqh_routing" = "PCH_IRQ11"
+
+ # VR Settings Configuration for 5 Domains
+ #+----------------+-------+-------+-------------+-------------+-------+
+ #| Domain/Setting | SA | IA | Ring Sliced | GT Unsliced | GT |
+ #+----------------+-------+-------+-------------+-------------+-------+
+ #| Psi1Threshold | 20A | 20A | 20A | 20A | 20A |
+ #| Psi2Threshold | 4A | 5A | 5A | 5A | 5A |
+ #| Psi3Threshold | 1A | 1A | 1A | 1A | 1A |
+ #| Psi3Enable | 1 | 1 | 1 | 1 | 1 |
+ #| Psi4Enable | 1 | 1 | 1 | 1 | 1 |
+ #| ImonSlope | 0 | 0 | 0 | 0 | 0 |
+ #| ImonOffset | 0 | 0 | 0 | 0 | 0 |
+ #| IccMax | 7A | 34A | 34A | 35A | 35A |
+ #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | 1.52V |
+ #+----------------+-------+-------+-------------+-------------+-------+
+ register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
+ .vr_config_enable = 1,
+ .psi1threshold = VR_CFG_AMP(20),
+ .psi2threshold = VR_CFG_AMP(4),
+ .psi3threshold = VR_CFG_AMP(1),
+ .psi3enable = 1,
+ .psi4enable = 1,
+ .imon_slope = 0x0,
+ .imon_offset = 0x0,
+ .icc_max = VR_CFG_AMP(7),
+ .voltage_limit = 1520,
+ }"
+
+ register "domain_vr_config[VR_IA_CORE]" = "{
+ .vr_config_enable = 1,
+ .psi1threshold = VR_CFG_AMP(20),
+ .psi2threshold = VR_CFG_AMP(5),
+ .psi3threshold = VR_CFG_AMP(1),
+ .psi3enable = 1,
+ .psi4enable = 1,
+ .imon_slope = 0x0,
+ .imon_offset = 0x0,
+ .icc_max = VR_CFG_AMP(34),
+ .voltage_limit = 1520,
+ }"
+
+ register "domain_vr_config[VR_RING]" = "{
+ .vr_config_enable = 1,
+ .psi1threshold = VR_CFG_AMP(20),
+ .psi2threshold = VR_CFG_AMP(5),
+ .psi3threshold = VR_CFG_AMP(1),
+ .psi3enable = 1,
+ .psi4enable = 1,
+ .imon_slope = 0x0,
+ .imon_offset = 0x0,
+ .icc_max = VR_CFG_AMP(34),
+ .voltage_limit = 1520,
+ }"
+
+ register "domain_vr_config[VR_GT_UNSLICED]" = "{
+ .vr_config_enable = 1,
+ .psi1threshold = VR_CFG_AMP(20),
+ .psi2threshold = VR_CFG_AMP(5),
+ .psi3threshold = VR_CFG_AMP(1),
+ .psi3enable = 1,
+ .psi4enable = 1,
+ .imon_slope = 0x0,
+ .imon_offset = 0x0,
+ .icc_max = VR_CFG_AMP(35),
+ .voltage_limit = 1520,
+ }"
+
+ register "domain_vr_config[VR_GT_SLICED]" = "{
+ .vr_config_enable = 1,
+ .psi1threshold = VR_CFG_AMP(20),
+ .psi2threshold = VR_CFG_AMP(5),
+ .psi3threshold = VR_CFG_AMP(1),
+ .psi3enable = 1,
+ .psi4enable = 1,
+ .imon_slope = 0x0,
+ .imon_offset = 0x0,
+ .icc_max = VR_CFG_AMP(35),
+ .voltage_limit = 1520,
+ }"
+
+ # Enable Root port 1
+ register "PcieRpEnable[0]" = "1"
+ # Enable CLKREQ#
+ register "PcieRpClkReqSupport[0]" = "1"
+ # RP 1 uses SRCCLKREQ1#
+ register "PcieRpClkReqNumber[0]" = "1"
+
+ register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port 1
+ register "usb2_ports[1]" = "USB2_PORT_MID(OC2)" # Card Reader
+ register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth
+ register "usb2_ports[4]" = "USB2_PORT_MID(OC2)" # Type-A Port (board)
+ register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera
+ register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # PIC MCU
+ register "usb2_ports[8]" = "USB2_PORT_LONG(OC3)" # Type-A Port (board)
+
+ register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C Port 1
+ register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Card Reader
+ register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port (board)
+ register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port (board)
+
+ register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" # I2C4 is 1.8V
+
+ # Must leave UART0 enabled or SD/eMMC will not work as PCI
+ register "SerialIoDevMode" = "{
+ [PchSerialIoIndexI2C0] = PchSerialIoPci,
+ [PchSerialIoIndexI2C1] = PchSerialIoPci,
+ [PchSerialIoIndexI2C2] = PchSerialIoDisabled,
+ [PchSerialIoIndexI2C3] = PchSerialIoDisabled,
+ [PchSerialIoIndexI2C4] = PchSerialIoPci,
+ [PchSerialIoIndexI2C5] = PchSerialIoDisabled,
+ [PchSerialIoIndexSpi0] = PchSerialIoDisabled,
+ [PchSerialIoIndexSpi1] = PchSerialIoDisabled,
+ [PchSerialIoIndexUart0] = PchSerialIoPci,
+ [PchSerialIoIndexUart1] = PchSerialIoDisabled,
+ [PchSerialIoIndexUart2] = PchSerialIoSkipInit,
+ }"
+
+ # PL2 override 25W
+ register "tdp_pl2_override" = "25"
+
+ # Send an extra VR mailbox command for the PS4 exit issue
+ register "SendVrMbxCmd" = "2"
+
+ # Lock Down
+ register "common_soc_config" = "{
+ .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT,
+ }"
+
+ device cpu_cluster 0 on
+ device lapic 0 on end
+ end
+ device domain 0 on
+ device pci 00.0 on end # Host Bridge
+ device pci 02.0 on end # Integrated Graphics Device
+ device pci 14.0 on end # USB xHCI
+ device pci 14.1 off end # USB xDCI (OTG)
+ device pci 14.2 on end # Thermal Subsystem
+ device pci 15.0 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0001""
+ register "desc" = ""ELAN Touchscreen""
+ register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)"
+ device i2c 10 on end
+ end
+ end # I2C #0
+ device pci 15.1 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0000""
+ register "desc" = ""ELAN Touchpad""
+ register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)"
+ register "wake" = "GPE0_DW0_05"
+ device i2c 15 on end
+ end
+ end # I2C #1
+ device pci 15.2 off end # I2C #2
+ device pci 15.3 off end # I2C #3
+ device pci 16.0 on end # Management Engine Interface 1
+ device pci 16.1 off end # Management Engine Interface 2
+ device pci 16.2 off end # Management Engine IDE-R
+ device pci 16.3 off end # Management Engine KT Redirection
+ device pci 16.4 off end # Management Engine Interface 3
+ device pci 17.0 off end # SATA
+ device pci 19.0 on end # UART #2
+ device pci 19.1 off end # I2C #5
+ device pci 19.2 on
+ chip drivers/i2c/nau8825
+ register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)"
+ register "jkdet_enable" = "1"
+ register "jkdet_pull_enable" = "0" # R389
+ register "jkdet_polarity" = "1" # ActiveLow
+ register "vref_impedance" = "2" # 125kOhm
+ register "micbias_voltage" = "6" # 2.754
+ register "sar_threshold_num" = "4"
+ register "sar_threshold[0]" = "0x08"
+ register "sar_threshold[1]" = "0x12"
+ register "sar_threshold[2]" = "0x26"
+ register "sar_threshold[3]" = "0x73"
+ register "sar_hysteresis" = "0"
+ register "sar_voltage" = "6"
+ register "sar_compare_time" = "1" # 1us
+ register "sar_sampling_time" = "1" # 4us
+ register "short_key_debounce" = "3" # 30ms
+ register "jack_insert_debounce" = "7" # 512ms
+ register "jack_eject_debounce" = "0"
+ device i2c 1a on end
+ end
+ end # I2C #4
+ device pci 1c.0 on
+ chip drivers/intel/wifi
+ register "wake" = "GPE0_DW0_16"
+ device pci 00.0 on end
+ end
+ end # PCI Express Port 1
+ device pci 1c.1 off end # PCI Express Port 2
+ device pci 1c.2 off end # PCI Express Port 3
+ device pci 1c.3 off end # PCI Express Port 4
+ device pci 1c.4 off end # PCI Express Port 5
+ device pci 1c.5 off end # PCI Express Port 6
+ device pci 1c.6 off end # PCI Express Port 7
+ device pci 1c.7 off end # PCI Express Port 8
+ device pci 1d.0 off end # PCI Express Port 9
+ device pci 1d.1 off end # PCI Express Port 10
+ device pci 1d.2 off end # PCI Express Port 11
+ device pci 1d.3 off end # PCI Express Port 12
+ device pci 1e.0 on end # UART #0
+ device pci 1e.1 off end # UART #1
+ device pci 1e.2 off end # GSPI #0
+ device pci 1e.3 off end # GSPI #1
+ device pci 1e.4 on end # eMMC
+ device pci 1e.5 off end # SDIO
+ device pci 1e.6 off end # SDCard
+ device pci 1f.0 on
+ chip drivers/pc80/tpm
+ device pnp 0c31.0 on end
+ end
+ chip ec/google/chromeec
+ device pnp 0c09.0 on end
+ end
+ end # LPC Interface
+ device pci 1f.1 on end # P2SB
+ device pci 1f.2 on end # Power Management Controller
+ device pci 1f.3 on
+ chip drivers/generic/max98357a
+ register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)"
+ register "sdmode_delay" = "5"
+ device generic 0 on end
+ end
+ end # Intel HDA
+ device pci 1f.4 on end # SMBus
+ device pci 1f.5 on end # PCH SPI
+ device pci 1f.6 off end # GbE
+ end
+end