## SPDX-License-Identifier: GPL-2.0-only

chip northbridge/intel/sandybridge
	# IGD Displays
	register "gfx.ndid" = "4"
	register "gfx.did" = "{ 0x80000400, 0x80000300, 0x80000301, 0x80000100, }"

	# Enable Panel as eDP and configure power delays
	register "gpu_panel_port_select" = "PANEL_PORT_DP_A"
	register "gpu_panel_power_cycle_delay" = "6"		# 500ms
	register "gpu_panel_power_up_delay" = "2000"		# 200ms
	register "gpu_panel_power_down_delay" = "500"		# 50ms
	register "gpu_panel_power_backlight_on_delay" = "1"	# 100us as recommended by PRM
	register "gpu_panel_power_backlight_off_delay" = "2000"	# 200ms

	# Set backlight PWM values for eDP
	register "gpu_cpu_backlight" = "0x00000ac8"
	register "gpu_pch_backlight" = "0x13120000"

	chip cpu/intel/model_206ax
		device cpu_cluster 0 on end

		register "acpi_c2" = "CPU_ACPI_C6"
		register "acpi_c3" = "CPU_ACPI_DISABLED"
	end

	device domain 0 on
		device ref host_bridge on end # host bridge
		device ref igd on end # vga controller

		chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH
			# LPC i/o generic decodes
			register "gen1_dec" = "0x003c0a01" # ITE environment controller
			register "gen2_dec" = "0x000403e9" # additional com port
			register "gen3_dec" = "0x000402e9" # additional com port

			# Enable both SATA ports 0, 1
			register "sata_port_map" = "0x03"
			# Set max SATA speed to 6.0 Gb/s (should be the default, anyway)
			register "sata_interface_speed_support" = "0x3"

			# Route GPI7 (EC SCI) as SCI
			register "gpi7_routing" = "2"

			# Enable GPE17 (GPI7) and TCO SCI
			register "gpe0_en" = "0x00800040"

			# Disable root port coalescing
			register "pcie_port_coalesce" = "false"
			register "pcie_hotplug_map" = "{ 0, 0, 0, 0, 0, 0, 1, 1 }"


			register "xhci_overcurrent_mapping"	= "0x00000c03"
			register "xhci_switchable_ports"	= "0x0f"
			register "superspeed_capable_ports"	= "0x0f"

			register "spi_uvscc" = "0x2005"
			register "spi_lvscc" = "0x2005"

			device ref xhci on end # USB 3.0 Controller
			device ref mei1 on end # Management Engine Interface 1
			device ref mei2 off end # Management Engine Interface 2
			device ref me_ide_r off end # Management Engine IDE-R
			device ref me_kt off end # Management Engine KT
			device ref gbe on end # Intel Gigabit Ethernet
			device ref ehci2 on end # USB2 EHCI #2
			device ref hda on # High Definition Audio
				subsystemid 0x1a86 0x4352
			end

			# Disabling 1c.0 might break IRQ settings as it enables port coalescing
			device ref pcie_rp1 on end # PCIe Port #1
			device ref pcie_rp2 on end # PCIe Port #2
			device ref pcie_rp3 on end # PCIe Port #3
			device ref pcie_rp4 on end # PCIe Port #4
			device ref pcie_rp5 on end # PCIe Port #5
			device ref pcie_rp6 on end # PCIe Port #6
			device ref pcie_rp7 on end # PCIe Port #7
			device ref pcie_rp8 on end # PCIe Port #8

			device ref ehci1 on end # USB2 EHCI #1
			device ref pci_bridge off end # PCI bridge
			device ref lpc on # LPC bridge
				chip ec/roda/it8518
					register "cpuhot_limit" = "100"
					# 60h/64h KBC
					device pnp ff.0 on # dummy address
					end
				end
				chip superio/ite/it8783ef
					register "TMPIN1.mode"		= "THERMAL_RESISTOR"
					register "TMPIN2.mode"		= "THERMAL_RESISTOR"
					register "ec.vin_mask"		= "VIN_ALL"
					register "FAN1.mode"		= "FAN_SMART_AUTOMATIC"
					register "FAN1.smart.tmpin"	= " 1"
					register "FAN1.smart.tmp_off"	= "60"
					register "FAN1.smart.tmp_start"	= "64"
					register "FAN1.smart.tmp_delta"	= " 2"
					register "FAN1.smart.pwm_start"	= "30"
					register "FAN1.smart.slope"	= "64"
					register "FAN2.mode"		= "FAN_SMART_AUTOMATIC"
					register "FAN2.smart.tmpin"	= " 1"
					register "FAN2.smart.tmp_off"	= "60"
					register "FAN2.smart.tmp_start"	= "64"
					register "FAN2.smart.tmp_delta"	= " 2"
					register "FAN2.smart.pwm_start"	= "30"
					register "FAN2.smart.slope"	= "64"
					register "FAN3.mode"		= "FAN_MODE_OFF"
					device pnp 2e.0 off end	# Floppy
					device pnp 2e.1 on	# COM 1
						io 0x60 = 0x3f8
						irq 0x70 = 4
					end
					device pnp 2e.2 on	# COM 2
						io 0x60 = 0x2f8
						irq 0x70 = 3
					end
					device pnp 2e.3 on	# Printer Port
						io 0x60 = 0x378
						io 0x62 = 0x000
						irq 0x70 = 7
						drq 0x74 = 4
						irq 0xf0 = 0x00
					end
					device pnp 2e.4 on	# Environment Controller
						io 0x60 = 0xa30
						io 0x62 = 0xa20
						irq 0x70 = 0
						irq 0xf0 = 0x80
					end
					device pnp 2e.5 off end	# Keyboard
					device pnp 2e.6 off end	# Mouse
					device pnp 2e.7 off end	# GPIO
					device pnp 2e.8 on	# COM 3
						io 0x60 = 0x3e8
						irq 0x70 = 4
					end
					device pnp 2e.9 on	# COM 4
						io 0x60 = 0x2e8
						irq 0x70 = 3
					end
					device pnp 2e.a off end	# COM 5
					device pnp 2e.b off end	# COM 6
					device pnp 2e.c off end	# CIR
				end
			end # LPC bridge
			device ref sata1 on end # SATA Controller 1
			device ref smbus on end # SMBus
			device ref sata2 off end # SATA Controller 2
			device ref thermal off end # Thermal
		end
	end
end