blob: 31f47f734022f65e3ed40cb2080335c3a857b121 [file] [log] [blame]
config SOC_INTEL_BROADWELL
bool
help
Intel Broadwell and Haswell ULT support.
if SOC_INTEL_BROADWELL
config CPU_SPECIFIC_OPTIONS
def_bool y
select ACPI_INTEL_HARDWARE_SLEEP_VALUES
select ARCH_ALL_STAGES_X86_32
select BOOT_DEVICE_SUPPORTS_WRITES
select CACHE_MRC_SETTINGS
select MRC_SETTINGS_PROTECT
select CPU_INTEL_COMMON
select CPU_INTEL_FIRMWARE_INTERFACE_TABLE
select SUPPORT_CPU_UCODE_IN_CBFS
select HAVE_SMI_HANDLER
select SOUTHBRIDGE_INTEL_COMMON_RESET
select SOUTHBRIDGE_INTEL_COMMON_RTC
select SOUTHBRIDGE_INTEL_COMMON_SMBUS
select SOUTHBRIDGE_INTEL_COMMON_SPI_ICH9
select HAVE_USBDEBUG
select IOAPIC
select REG_SCRIPT
select PARALLEL_MP
select RTC
select SPI_FLASH
select SSE2
select TSC_SYNC_MFENCE
select UDELAY_TSC
select TSC_MONOTONIC_TIMER
select SOC_INTEL_COMMON
select SOC_INTEL_COMMON_BLOCK
select SOC_INTEL_COMMON_BLOCK_CPU
select SOC_INTEL_COMMON_BLOCK_POWER_LIMIT
select INTEL_DESCRIPTOR_MODE_CAPABLE
select SOC_INTEL_COMMON_ACPI_WAKE_SOURCE
select HAVE_SPI_CONSOLE_SUPPORT
select INTEL_GMA_ACPI
select HAVE_POWER_STATE_AFTER_FAILURE
select HAVE_POWER_STATE_PREVIOUS_AFTER_FAILURE
config PCIEXP_ASPM
bool
default y
config PCIEXP_AER
bool
default y
config PCIEXP_COMMON_CLOCK
bool
default y
config PCIEXP_CLK_PM
bool
default y
config PCIEXP_L1_SUB_STATE
bool
default y
config BROADWELL_VBOOT_IN_BOOTBLOCK
depends on VBOOT
bool "Start verstage in bootblock"
default y
select VBOOT_STARTS_IN_BOOTBLOCK
select VBOOT_SEPARATE_VERSTAGE
help
Broadwell can either start verstage in a separate stage
right after the bootblock has run or it can start it
after romstage for compatibility reasons.
Broadwell however uses a mrc.bin to initialse memory which
needs to be located at a fixed offset. Therefore even with
a separate verstage starting after the bootblock that same
binary is used meaning a jump is made from RW to the RO region
and back to the RW region after the binary is done.
config VBOOT
select VBOOT_MUST_REQUEST_DISPLAY
select VBOOT_STARTS_IN_ROMSTAGE if !BROADWELL_VBOOT_IN_BOOTBLOCK
config MMCONF_BASE_ADDRESS
hex
default 0xf0000000
config SMM_TSEG_SIZE
hex
default 0x800000
config IED_REGION_SIZE
hex
default 0x400000
config SMM_RESERVED_SIZE
hex
default 0x100000
config VGA_BIOS_ID
string
default "8086,0406"
config DCACHE_RAM_BASE
hex
default 0xff7c0000
config DCACHE_RAM_SIZE
hex
default 0x10000
help
The size of the cache-as-ram region required during bootblock
and/or romstage. Note DCACHE_RAM_SIZE and DCACHE_RAM_MRC_VAR_SIZE
must add up to a power of 2.
config DCACHE_RAM_MRC_VAR_SIZE
hex
default 0x30000
help
The amount of cache-as-ram region required by the reference code.
config DCACHE_BSP_STACK_SIZE
hex
default 0x2000
help
The amount of anticipated stack usage in CAR by bootblock and
other stages.
config HAVE_MRC
bool "Add a Memory Reference Code binary"
help
Select this option to add a Memory Reference Code binary to
the resulting coreboot image.
Note: Without this binary coreboot will not work
if HAVE_MRC
config MRC_FILE
string "Intel Memory Reference Code path and filename"
depends on HAVE_MRC
default "mrc.bin"
help
The filename of the file to use as Memory Reference Code binary.
config MRC_BIN_ADDRESS
hex
default 0xfffa0000
# The UEFI System Agent binary needs to be at a fixed offset in the flash
# and can therefore only reside in the COREBOOT fmap region
config RO_REGION_ONLY
string
depends on VBOOT
default "mrc.bin"
endif # HAVE_MRC
config PRE_GRAPHICS_DELAY
int "Graphics initialization delay in ms"
default 0
help
On some systems, coreboot boots so fast that connected monitors
(mostly TVs) won't be able to wake up fast enough to talk to the
VBIOS. On those systems we need to wait for a bit before executing
the VBIOS.
config INTEL_PCH_UART_CONSOLE
bool "Use Serial IO UART for console"
default n
select DRIVERS_UART_8250MEM
config INTEL_PCH_UART_CONSOLE_NUMBER
hex "Serial IO UART number to use for console"
default 0x0
depends on INTEL_PCH_UART_CONSOLE
config TTYS0_BASE
hex
default 0xd6000000
depends on INTEL_PCH_UART_CONSOLE
config EHCI_BAR
hex
default 0xd8000000
config SERIRQ_CONTINUOUS_MODE
bool
default y
help
If you set this option to y, the serial IRQ machine will be
operated in continuous mode.
config HAVE_REFCODE_BLOB
depends on ARCH_X86
bool "An external reference code blob should be put into cbfs."
default n
help
The reference code blob will be placed into cbfs.
if HAVE_REFCODE_BLOB
config REFCODE_BLOB_FILE
string "Path and filename to reference code blob."
default "refcode.elf"
help
The path and filename to the file to be added to cbfs.
endif # HAVE_REFCODE_BLOB
endif