- Add pci_def.h so romcc compiled files can also get at the
pci definitions
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
diff --git a/src/include/device/pci_def.h b/src/include/device/pci_def.h
new file mode 100644
index 0000000..6a22cbe6
--- /dev/null
+++ b/src/include/device/pci_def.h
@@ -0,0 +1,264 @@
+#ifndef PCI_DEF_H
+#define PCI_DEF_H
+
+/*
+ * Under PCI, each device has 256 bytes of configuration address space,
+ * of which the first 64 bytes are standardized as follows:
+ */
+#define PCI_VENDOR_ID 0x00 /* 16 bits */
+#define PCI_DEVICE_ID 0x02 /* 16 bits */
+#define PCI_COMMAND 0x04 /* 16 bits */
+#define PCI_COMMAND_IO 0x1 /* Enable response in I/O space */
+#define PCI_COMMAND_MEMORY 0x2 /* Enable response in Memory space */
+#define PCI_COMMAND_MASTER 0x4 /* Enable bus mastering */
+#define PCI_COMMAND_SPECIAL 0x8 /* Enable response to special cycles */
+#define PCI_COMMAND_INVALIDATE 0x10 /* Use memory write and invalidate */
+#define PCI_COMMAND_VGA_PALETTE 0x20 /* Enable palette snooping */
+#define PCI_COMMAND_PARITY 0x40 /* Enable parity checking */
+#define PCI_COMMAND_WAIT 0x80 /* Enable address/data stepping */
+#define PCI_COMMAND_SERR 0x100 /* Enable SERR */
+#define PCI_COMMAND_FAST_BACK 0x200 /* Enable back-to-back writes */
+
+#define PCI_STATUS 0x06 /* 16 bits */
+#define PCI_STATUS_CAP_LIST 0x10 /* Support Capability List */
+#define PCI_STATUS_66MHZ 0x20 /* Support 66 Mhz PCI 2.1 bus */
+#define PCI_STATUS_UDF 0x40 /* Support User Definable Features [obsolete] */
+#define PCI_STATUS_FAST_BACK 0x80 /* Accept fast-back to back */
+#define PCI_STATUS_PARITY 0x100 /* Detected parity error */
+#define PCI_STATUS_DEVSEL_MASK 0x600 /* DEVSEL timing */
+#define PCI_STATUS_DEVSEL_FAST 0x000
+#define PCI_STATUS_DEVSEL_MEDIUM 0x200
+#define PCI_STATUS_DEVSEL_SLOW 0x400
+#define PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */
+#define PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */
+#define PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */
+#define PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */
+#define PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */
+
+#define PCI_CLASS_REVISION 0x08 /* High 24 bits are class, low 8
+ revision */
+#define PCI_REVISION_ID 0x08 /* Revision ID */
+#define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */
+#define PCI_CLASS_DEVICE 0x0a /* Device class */
+
+#define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */
+#define PCI_LATENCY_TIMER 0x0d /* 8 bits */
+#define PCI_HEADER_TYPE 0x0e /* 8 bits */
+#define PCI_HEADER_TYPE_NORMAL 0
+#define PCI_HEADER_TYPE_BRIDGE 1
+#define PCI_HEADER_TYPE_CARDBUS 2
+
+#define PCI_BIST 0x0f /* 8 bits */
+#define PCI_BIST_CODE_MASK 0x0f /* Return result */
+#define PCI_BIST_START 0x40 /* 1 to start BIST, 2 secs or less */
+#define PCI_BIST_CAPABLE 0x80 /* 1 if BIST capable */
+
+/*
+ * Base addresses specify locations in memory or I/O space.
+ * Decoded size can be determined by writing a value of
+ * 0xffffffff to the register, and reading it back. Only
+ * 1 bits are decoded.
+ */
+#define PCI_BASE_ADDRESS_0 0x10 /* 32 bits */
+#define PCI_BASE_ADDRESS_1 0x14 /* 32 bits [htype 0,1 only] */
+#define PCI_BASE_ADDRESS_2 0x18 /* 32 bits [htype 0 only] */
+#define PCI_BASE_ADDRESS_3 0x1c /* 32 bits */
+#define PCI_BASE_ADDRESS_4 0x20 /* 32 bits */
+#define PCI_BASE_ADDRESS_5 0x24 /* 32 bits */
+#define PCI_BASE_ADDRESS_SPACE 0x01 /* 0 = memory, 1 = I/O */
+#define PCI_BASE_ADDRESS_SPACE_IO 0x01
+#define PCI_BASE_ADDRESS_SPACE_MEMORY 0x00
+#define PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06
+#define PCI_BASE_ADDRESS_MEM_TYPE_32 0x00 /* 32 bit address */
+#define PCI_BASE_ADDRESS_MEM_TYPE_1M 0x02 /* Below 1M [obsolete] */
+#define PCI_BASE_ADDRESS_MEM_TYPE_64 0x04 /* 64 bit address */
+#define PCI_BASE_ADDRESS_MEM_PREFETCH 0x08 /* prefetchable? */
+#define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL)
+#define PCI_BASE_ADDRESS_IO_MASK (~0x03UL)
+/* bit 1 is reserved if address_space = 1 */
+
+/* Header type 0 (normal devices) */
+#define PCI_CARDBUS_CIS 0x28
+#define PCI_SUBSYSTEM_VENDOR_ID 0x2c
+#define PCI_SUBSYSTEM_ID 0x2e
+#define PCI_ROM_ADDRESS 0x30 /* Bits 31..11 are address, 10..1 reserved */
+#define PCI_ROM_ADDRESS_ENABLE 0x01
+#define PCI_ROM_ADDRESS_MASK (~0x7ffUL)
+
+#define PCI_CAPABILITY_LIST 0x34 /* Offset of first capability list entry */
+
+/* 0x35-0x3b are reserved */
+#define PCI_INTERRUPT_LINE 0x3c /* 8 bits */
+#define PCI_INTERRUPT_PIN 0x3d /* 8 bits */
+#define PCI_MIN_GNT 0x3e /* 8 bits */
+#define PCI_MAX_LAT 0x3f /* 8 bits */
+
+/* Header type 1 (PCI-to-PCI bridges) */
+#define PCI_PRIMARY_BUS 0x18 /* Primary bus number */
+#define PCI_SECONDARY_BUS 0x19 /* Secondary bus number */
+#define PCI_SUBORDINATE_BUS 0x1a /* Highest bus number behind the bridge */
+#define PCI_SEC_LATENCY_TIMER 0x1b /* Latency timer for secondary interface */
+#define PCI_IO_BASE 0x1c /* I/O range behind the bridge */
+#define PCI_IO_LIMIT 0x1d
+#define PCI_IO_RANGE_TYPE_MASK 0x0f /* I/O bridging type */
+#define PCI_IO_RANGE_TYPE_16 0x00
+#define PCI_IO_RANGE_TYPE_32 0x01
+#define PCI_IO_RANGE_MASK ~0x0f
+#define PCI_SEC_STATUS 0x1e /* Secondary status register, only bit 14 used */
+#define PCI_MEMORY_BASE 0x20 /* Memory range behind */
+#define PCI_MEMORY_LIMIT 0x22
+#define PCI_MEMORY_RANGE_TYPE_MASK 0x0f
+#define PCI_MEMORY_RANGE_MASK ~0x0f
+#define PCI_PREF_MEMORY_BASE 0x24 /* Prefetchable memory range behind */
+#define PCI_PREF_MEMORY_LIMIT 0x26
+#define PCI_PREF_RANGE_TYPE_MASK 0x0f
+#define PCI_PREF_RANGE_TYPE_32 0x00
+#define PCI_PREF_RANGE_TYPE_64 0x01
+#define PCI_PREF_RANGE_MASK ~0x0f
+#define PCI_PREF_BASE_UPPER32 0x28 /* Upper half of prefetchable memory range */
+#define PCI_PREF_LIMIT_UPPER32 0x2c
+#define PCI_IO_BASE_UPPER16 0x30 /* Upper half of I/O addresses */
+#define PCI_IO_LIMIT_UPPER16 0x32
+/* 0x34 same as for htype 0 */
+/* 0x35-0x3b is reserved */
+#define PCI_ROM_ADDRESS1 0x38 /* Same as PCI_ROM_ADDRESS, but for htype 1 */
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_BRIDGE_CONTROL 0x3e
+#define PCI_BRIDGE_CTL_PARITY 0x01 /* Enable parity detection on secondary interface */
+#define PCI_BRIDGE_CTL_SERR 0x02 /* The same for SERR forwarding */
+#define PCI_BRIDGE_CTL_NO_ISA 0x04 /* Disable bridging of ISA ports */
+#define PCI_BRIDGE_CTL_VGA 0x08 /* Forward VGA addresses */
+#define PCI_BRIDGE_CTL_MASTER_ABORT 0x20 /* Report master aborts */
+#define PCI_BRIDGE_CTL_BUS_RESET 0x40 /* Secondary bus reset */
+#define PCI_BRIDGE_CTL_FAST_BACK 0x80 /* Fast Back2Back enabled on secondary interface */
+
+/* Header type 2 (CardBus bridges) */
+#define PCI_CB_CAPABILITY_LIST 0x14
+/* 0x15 reserved */
+#define PCI_CB_SEC_STATUS 0x16 /* Secondary status */
+#define PCI_CB_PRIMARY_BUS 0x18 /* PCI bus number */
+#define PCI_CB_CARD_BUS 0x19 /* CardBus bus number */
+#define PCI_CB_SUBORDINATE_BUS 0x1a /* Subordinate bus number */
+#define PCI_CB_LATENCY_TIMER 0x1b /* CardBus latency timer */
+#define PCI_CB_MEMORY_BASE_0 0x1c
+#define PCI_CB_MEMORY_LIMIT_0 0x20
+#define PCI_CB_MEMORY_BASE_1 0x24
+#define PCI_CB_MEMORY_LIMIT_1 0x28
+#define PCI_CB_IO_BASE_0 0x2c
+#define PCI_CB_IO_BASE_0_HI 0x2e
+#define PCI_CB_IO_LIMIT_0 0x30
+#define PCI_CB_IO_LIMIT_0_HI 0x32
+#define PCI_CB_IO_BASE_1 0x34
+#define PCI_CB_IO_BASE_1_HI 0x36
+#define PCI_CB_IO_LIMIT_1 0x38
+#define PCI_CB_IO_LIMIT_1_HI 0x3a
+#define PCI_CB_IO_RANGE_MASK ~0x03
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_CB_BRIDGE_CONTROL 0x3e
+#define PCI_CB_BRIDGE_CTL_PARITY 0x01 /* Similar to standard bridge control register */
+#define PCI_CB_BRIDGE_CTL_SERR 0x02
+#define PCI_CB_BRIDGE_CTL_ISA 0x04
+#define PCI_CB_BRIDGE_CTL_VGA 0x08
+#define PCI_CB_BRIDGE_CTL_MASTER_ABORT 0x20
+#define PCI_CB_BRIDGE_CTL_CB_RESET 0x40 /* CardBus reset */
+#define PCI_CB_BRIDGE_CTL_16BIT_INT 0x80 /* Enable interrupt for 16-bit cards */
+#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100 /* Prefetch enable for both memory regions */
+#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
+#define PCI_CB_BRIDGE_CTL_POST_WRITES 0x400
+#define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40
+#define PCI_CB_SUBSYSTEM_ID 0x42
+#define PCI_CB_LEGACY_MODE_BASE 0x44 /* 16-bit PC Card legacy mode base address (ExCa) */
+/* 0x48-0x7f reserved */
+
+/* Capability lists */
+
+#define PCI_CAP_LIST_ID 0 /* Capability ID */
+#define PCI_CAP_ID_PM 0x01 /* Power Management */
+#define PCI_CAP_ID_AGP 0x02 /* Accelerated Graphics Port */
+#define PCI_CAP_ID_VPD 0x03 /* Vital Product Data */
+#define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */
+#define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */
+#define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */
+#define PCI_CAP_ID_HT 0x08
+#define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */
+#define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */
+#define PCI_CAP_SIZEOF 4
+
+/* Power Management Registers */
+
+#define PCI_PM_CAP_VER_MASK 0x0007 /* Version */
+#define PCI_PM_CAP_PME_CLOCK 0x0008 /* PME clock required */
+#define PCI_PM_CAP_AUX_POWER 0x0010 /* Auxilliary power support */
+#define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization */
+#define PCI_PM_CAP_D1 0x0200 /* D1 power state support */
+#define PCI_PM_CAP_D2 0x0400 /* D2 power state support */
+#define PCI_PM_CAP_PME 0x0800 /* PME pin supported */
+#define PCI_PM_CTRL 4 /* PM control and status register */
+#define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */
+#define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */
+#define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* Data select (??) */
+#define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* Data scale (??) */
+#define PCI_PM_CTRL_PME_STATUS 0x8000 /* PME pin status */
+#define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions (??) */
+#define PCI_PM_PPB_B2_B3 0x40 /* Stop clock when in D3hot (??) */
+#define PCI_PM_BPCC_ENABLE 0x80 /* Bus power/clock control enable (??) */
+#define PCI_PM_DATA_REGISTER 7 /* (??) */
+#define PCI_PM_SIZEOF 8
+
+/* AGP registers */
+
+#define PCI_AGP_VERSION 2 /* BCD version number */
+#define PCI_AGP_RFU 3 /* Rest of capability flags */
+#define PCI_AGP_STATUS 4 /* Status register */
+#define PCI_AGP_STATUS_RQ_MASK 0xff000000 /* Maximum number of requests - 1 */
+#define PCI_AGP_STATUS_SBA 0x0200 /* Sideband addressing supported */
+#define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing supported */
+#define PCI_AGP_STATUS_FW 0x0010 /* FW transfers supported */
+#define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported */
+#define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported */
+#define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported */
+#define PCI_AGP_COMMAND 8 /* Control register */
+#define PCI_AGP_COMMAND_RQ_MASK 0xff000000 /* Master: Maximum number of requests */
+#define PCI_AGP_COMMAND_SBA 0x0200 /* Sideband addressing enabled */
+#define PCI_AGP_COMMAND_AGP 0x0100 /* Allow processing of AGP transactions */
+#define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow processing of 64-bit addresses */
+#define PCI_AGP_COMMAND_FW 0x0010 /* Force FW transfers */
+#define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate */
+#define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 4x rate */
+#define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 4x rate */
+#define PCI_AGP_SIZEOF 12
+
+/* Slot Identification */
+
+#define PCI_SID_ESR 2 /* Expansion Slot Register */
+#define PCI_SID_ESR_NSLOTS 0x1f /* Number of expansion slots available */
+#define PCI_SID_ESR_FIC 0x20 /* First In Chassis Flag */
+#define PCI_SID_CHASSIS_NR 3 /* Chassis Number */
+
+/* Message Signalled Interrupts registers */
+
+#define PCI_MSI_FLAGS 2 /* Various flags */
+#define PCI_MSI_FLAGS_64BIT 0x80 /* 64-bit addresses allowed */
+#define PCI_MSI_FLAGS_QSIZE 0x70 /* Message queue size configured */
+#define PCI_MSI_FLAGS_QMASK 0x0e /* Maximum queue size available */
+#define PCI_MSI_FLAGS_ENABLE 0x01 /* MSI feature enabled */
+#define PCI_MSI_RFU 3 /* Rest of capability flags */
+#define PCI_MSI_ADDRESS_LO 4 /* Lower 32 bits */
+#define PCI_MSI_ADDRESS_HI 8 /* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
+#define PCI_MSI_DATA_32 8 /* 16 bits of data for 32-bit devices */
+#define PCI_MSI_DATA_64 12 /* 16 bits of data for 64-bit devices */
+
+/*
+ * The PCI interface treats multi-function devices as independent
+ * devices. The slot/function address of each device is encoded
+ * in a single byte as follows:
+ *
+ * 7:3 = slot
+ * 2:0 = function
+ */
+#define PCI_DEVFN(slot,func) ((((slot) & 0x1f) << 3) | ((func) & 0x07))
+#define PCI_SLOT(devfn) (((devfn) >> 3) & 0x1f)
+#define PCI_FUNC(devfn) ((devfn) & 0x07)
+#define PCI_BDF(bus,dev,func) ((bus) << 16 | (dev) << 11 | (func) << 8)
+
+#endif /* PCI_DEF_H */