sb/intel/lynxpoint: Add native thermal init
Implement native thermal initialisation for Lynx Point. This is only
needed when MRC.bin is not used.
Change-Id: I4a67a3092d0c2e56bfdacb513a899ef838193cbd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64180
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
diff --git a/src/southbridge/intel/lynxpoint/thermal.c b/src/southbridge/intel/lynxpoint/thermal.c
new file mode 100644
index 0000000..e71969e
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/thermal.c
@@ -0,0 +1,64 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+
+#include <device/mmio.h>
+#include <device/pci_ops.h>
+#include <southbridge/intel/lynxpoint/pch.h>
+#include <types.h>
+
+#define TBARB_TEMP 0x40000000
+
+#define THERMAL_DEV PCI_DEV(0, 0x1f, 6)
+
+/* Early thermal init, it may need to be done prior to giving ME its memory */
+void early_thermal_init(void)
+{
+ /* Program address for temporary BAR */
+ pci_write_config32(THERMAL_DEV, 0x40, TBARB_TEMP);
+ pci_write_config32(THERMAL_DEV, 0x44, 0);
+
+ /* Activate temporary BAR */
+ pci_or_config32(THERMAL_DEV, 0x40, 1);
+
+ /*
+ * BWG section 17.3.1 says:
+ *
+ * ### Initializing Lynx Point Thermal Sensors ###
+ *
+ * The System BIOS must perform the following steps to initialize the Lynx
+ * Point thermal subsystem device, D31:F6. The System BIOS is required to
+ * repeat this process on a resume from Sx. BIOS may enable any or all of
+ * the registers below based on OEM's platform configuration. Intel does
+ * not recommend a value on some of the registers, since each platform has
+ * different temperature trip points and one may enable a trip to cause an
+ * SMI while another platform would cause an interrupt instead.
+ *
+ * The recommended flow for enabling thermal sensor is by setting up various
+ * temperature trip points first, followed by enabling the desired trip
+ * alert method and then enable the actual sensors from TSEL registers.
+ * If this flow is not followed, software will need to take special care
+ * to handle false events during setting up those registers.
+ */
+
+ /* Step 1: Program CTT */
+ write16p(TBARB_TEMP + 0x10, 0x0154);
+
+ /* Step 2: Clear trip status from TSS and TAS */
+ write8p(TBARB_TEMP + 0x06, 0xff);
+ write8p(TBARB_TEMP + 0x80, 0xff);
+
+ /* Step 3: Program TSGPEN and TSPIEN to zero */
+ write8p(TBARB_TEMP + 0x84, 0x00);
+ write8p(TBARB_TEMP + 0x82, 0x00);
+
+ /*
+ * Step 4: If thermal reporting to an EC over SMBus is supported,
+ * then write 0x01 to TSREL, else leave at default.
+ */
+ write8p(TBARB_TEMP + 0x0a, 0x01);
+
+ /* Disable temporary BAR */
+ pci_and_config32(THERMAL_DEV, 0x40, ~1);
+
+ /* Clear temporary BAR address */
+ pci_write_config32(THERMAL_DEV, 0x40, 0);
+}