/* SPDX-License-Identifier: GPL-2.0-only */

#include <arch/romstage.h>
#include <arch/io.h>
#include <cf9_reset.h>
#include <console/console.h>
#include <device/pci_ops.h>
#include <soc/fiamux.h>
#include <device/mmio.h>
#include <soc/iomap.h>
#include <soc/pci_devs.h>
#include <soc/pcr.h>
#include <soc/pmc.h>
#include <soc/romstage.h>
#include <soc/smbus.h>
#include <soc/soc_util.h>
#include <soc/hob_mem.h>

void __weak mainboard_config_gpios(void) {}

#if CONFIG(DISPLAY_HOBS)
static void display_fsp_smbios_memory_info_hob(void)
{
	const FSP_SMBIOS_MEMORY_INFO *memory_info_hob;

	/* Get the memory info HOB */
	memory_info_hob = soc_get_fsp_smbios_memory_info_hob();

	if (memory_info_hob == NULL)
		return;

	soc_display_fsp_smbios_memory_info_hob(memory_info_hob);
}
#endif

static void early_pmc_init(void)
{
	/* PMC (B0:D31:F2). */
	pci_devfn_t dev = PCH_DEV_PMC;

	/* Is PMC present */
	if (pci_read_config16(dev, 0) == 0xffff) {
		printk(BIOS_ERR, "PMC controller (B0:D31:F2) does not present!\n");
		return;
	}

	uint32_t pwrm_base =
		pci_read_config32(dev, PMC_PWRM_BASE) & MASK_PMC_PWRM_BASE;
	if (!pwrm_base) {
		printk(BIOS_ERR, "PWRM base address is not configured!\n");
		return;
	}

	/* Workaround for sighting report (doc#: 560805) v1.86.
	   42. System Might Hang In AC Power Loss
	   Problem :
	       When removing and reapplying AC power to the board,
	       the system might hang at serial output
	       'RESET required : change of frequency'
	       due to PMC ROM change on B0.
	   Implication :
	       1. This issue is only shown in B0 stepping.
	       2. This issue does not impact a system without an RTC battery.
	   Alternative workaround :
	       Remove RTC battery on the board if possible.
	   Status : Plan Fix.
	*/
	if (silicon_stepping() == SILICON_REV_DENVERTON_B0) {
		if (!(pci_read_config32(dev, GEN_PMCON_B)
					& GEN_PMCON_B_RTC_PWR_STS)) {
			if (read32((void *)(pwrm_base + 0x124))
				   & ((1 << 11) | (1 << 12))) {
				/* Performs a global reset */
				printk(BIOS_DEBUG,
					"Requesting Global Reset...\n");
				pci_write_config32(dev, ETR3,
					pci_read_config32(dev, ETR3)
					| ETR3_CF9GR);
				full_reset();
			}
		}
	}
}

static void early_tco_init(void)
{
	/* SMBUS (B0:D31:F4). */
	pci_devfn_t dev = PCI_DEV(0, SMBUS_DEV, SMBUS_FUNC);

	/* Configure TCO base address */
	if (pci_read_config16(dev, TCOBASE) == 0xffff) {
		printk(BIOS_ERR, "SMBus controller (B0:D31:F4) does not present!\n");
		return;
	}
	uint16_t tco_ctl = pci_read_config16(dev, TCOCTL);
	if (tco_ctl & TCOBASE_LOCK) {
		printk(BIOS_ERR, "TCO base register already has been locked!\n");
	} else {
		pci_write_config16(dev, TCOCTL, tco_ctl & (~TCOBASE_EN));
		pci_write_config16(dev, TCOBASE, DEFAULT_TCO_BASE | 0x1);
		pci_write_config16(dev, TCOCTL, tco_ctl | TCOBASE_EN);
	}

	uint16_t tco_base = pci_read_config16(dev, TCOBASE) & MASK_TCOBASE;
	printk(BIOS_DEBUG, "TCO base address set to 0x%x!\n", tco_base);

	/* Disable the TCO timer expiration from causing a system reset */
	MMIO32_OR(PCH_PCR_ADDRESS(PID_SMB, PCR_SMBUS_GC),
		(uint32_t)PCR_SMBUS_GC_NR);

	/*  Halt the TCO timer */
	uint16_t reg16 = inw(tco_base + TCO1_CNT);
	reg16 |= TCO_TMR_HLT;
	outw(reg16, tco_base + TCO1_CNT);

	/* Clear the Second TCO status bit */
	reg16 = inw(tco_base + TCO2_STS);
	reg16 |= TCO2_STS_SECOND_TO;
	outw(reg16, tco_base + TCO2_STS);
}

void mainboard_romstage_entry(void)
{
	printk(BIOS_DEBUG, "FSP TempRamInit was successful...\n");

	mainboard_config_gpios();
	early_tco_init();
	early_pmc_init();

	fsp_memory_init(false);

#if CONFIG(DISPLAY_HOBS)
	display_fsp_smbios_memory_info_hob();
#endif
}

static void soc_memory_init_params(FSP_M_CONFIG *m_cfg)
{
	FSPM_UPD *mupd = container_of(m_cfg, FSPM_UPD, FspmConfig);
	size_t num;
	uint16_t supported_hsio_lanes;
	BL_HSIO_INFORMATION *hsio_config;

	/* Set the parameters for MemoryInit */
	m_cfg->PcdEnableIQAT = CONFIG(IQAT_ENABLE);

	/* if ME HECI communication is disabled, apply default one*/
	if (mupd->FspmConfig.PcdMeHeciCommunication == 0) {

		/* Configure FIA MUX PCD */
		/* Assume the validating silicon has max lanes. */
		supported_hsio_lanes = BL_ME_FIA_MUX_LANE_NUM_MAX;

		num = mainboard_get_hsio_config(&hsio_config);

		if (get_fiamux_hsio_info(supported_hsio_lanes, num,
					 &hsio_config))
			die("HSIO Configuration is invalid, please correct "
			    "it!");

		mupd->FspmConfig.PcdHsioLanesNumber =
		    (uint32_t)hsio_config->NumLanesSupported;
		mupd->FspmConfig.PcdFiaMuxConfigPtr =
		    (uint32_t)&hsio_config->FiaConfig;
	}
}

__weak void mainboard_memory_init_params(FSPM_UPD *mupd)
{
	/* Do nothing */
}

void platform_fsp_memory_init_params_cb(FSPM_UPD *mupd, uint32_t version)
{
	FSP_M_CONFIG *m_cfg = &mupd->FspmConfig;

	soc_memory_init_params(m_cfg);

	mainboard_memory_init_params(mupd);
}