break the tree really quick due to svn restrictions, next commit fill fix it
again.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2240 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
diff --git a/src/southbridge/intel/ich5r/i82801er_lpc.c b/src/southbridge/intel/ich5r/i82801er_lpc.c
new file mode 100644
index 0000000..3f77b51
--- /dev/null
+++ b/src/southbridge/intel/ich5r/i82801er_lpc.c
@@ -0,0 +1,392 @@
+/*
+ * (C) 2004 Linux Networx
+ */
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <pc80/mc146818rtc.h>
+#include <pc80/isa-dma.h>
+#include <arch/io.h>
+#include "i82801er.h"
+
+#define ACPI_BAR 0x40
+#define GPIO_BAR 0x58
+
+#define NMI_OFF 0
+#define MAINBOARD_POWER_OFF 0
+#define MAINBOARD_POWER_ON 1
+
+#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#endif
+
+#define ALL (0xff << 24)
+#define NONE (0)
+#define DISABLED (1 << 16)
+#define ENABLED (0 << 16)
+#define TRIGGER_EDGE (0 << 15)
+#define TRIGGER_LEVEL (1 << 15)
+#define POLARITY_HIGH (0 << 13)
+#define POLARITY_LOW (1 << 13)
+#define PHYSICAL_DEST (0 << 11)
+#define LOGICAL_DEST (1 << 11)
+#define ExtINT (7 << 8)
+#define NMI (4 << 8)
+#define SMI (2 << 8)
+#define INT (1 << 8)
+
+static void setup_ioapic(void)
+{
+ int i;
+ unsigned long value_low, value_high;
+ unsigned long ioapic_base = 0xfec00000;
+ volatile unsigned long *l;
+ unsigned interrupts;
+
+ l = (unsigned long *) ioapic_base;
+
+ l[0] = 0x01;
+ interrupts = (l[04] >> 16) & 0xff;
+ for (i = 0; i < interrupts; i++) {
+ l[0] = (i * 2) + 0x10;
+ l[4] = DISABLED;
+ value_low = l[4];
+ l[0] = (i * 2) + 0x11;
+ l[4] = NONE; /* Should this be an address? */
+ value_high = l[4];
+ if (value_low == 0xffffffff) {
+ printk_warning("IO APIC not responding.\n");
+ return;
+ }
+ }
+
+ /* Put the ioapic in virtual wire mode */
+ l[0] = 0 + 0x10;
+ l[4] = ENABLED | TRIGGER_EDGE | POLARITY_HIGH | PHYSICAL_DEST | ExtINT;
+}
+
+#define SERIRQ_CNTL 0x64
+static void i82801er_enable_serial_irqs(device_t dev)
+{
+ /* set packet length and toggle silent mode bit */
+ pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(1 << 6)|((21 - 17) << 2)|(0 << 0));
+ pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(0 << 6)|((21 - 17) << 2)|(0 << 0));
+}
+
+#define PCI_DMA_CFG 0x90
+static void i82801er_pci_dma_cfg(device_t dev)
+{
+ /* Set PCI DMA CFG to lpc I/F DMA */
+ pci_write_config16(dev, PCI_DMA_CFG, 0xfcff);
+}
+
+#define LPC_EN 0xe6
+static void i82801er_enable_lpc(device_t dev)
+{
+ /* lpc i/f enable */
+ pci_write_config8(dev, LPC_EN, 0x0d);
+}
+
+typedef struct southbridge_intel_i82801er_config config_t;
+
+static void set_i82801er_gpio_use_sel(
+ device_t dev, struct resource *res, config_t *config)
+{
+ uint32_t gpio_use_sel, gpio_use_sel2;
+ int i;
+
+ gpio_use_sel = 0x1A003180;
+ gpio_use_sel2 = 0x00000007;
+ for(i = 0; i < 64; i++) {
+ int val;
+ switch(config->gpio[i] & ICH5R_GPIO_USE_MASK) {
+ case ICH5R_GPIO_USE_AS_NATIVE: val = 0; break;
+ case ICH5R_GPIO_USE_AS_GPIO: val = 1; break;
+ default:
+ continue;
+ }
+ /* The caller is responsible for not playing with unimplemented bits */
+ if (i < 32) {
+ gpio_use_sel &= ~( 1 << i);
+ gpio_use_sel |= (val << i);
+ } else {
+ gpio_use_sel2 &= ~( 1 << (i - 32));
+ gpio_use_sel2 |= (val << (i - 32));
+ }
+ }
+ outl(gpio_use_sel, res->base + 0x00);
+ outl(gpio_use_sel2, res->base + 0x30);
+}
+
+static void set_i82801er_gpio_direction(
+ device_t dev, struct resource *res, config_t *config)
+{
+ uint32_t gpio_io_sel, gpio_io_sel2;
+ int i;
+
+ gpio_io_sel = 0x0000ffff;
+ gpio_io_sel2 = 0x00000300;
+ for(i = 0; i < 64; i++) {
+ int val;
+ switch(config->gpio[i] & ICH5R_GPIO_SEL_MASK) {
+ case ICH5R_GPIO_SEL_OUTPUT: val = 0; break;
+ case ICH5R_GPIO_SEL_INPUT: val = 1; break;
+ default:
+ continue;
+ }
+ /* The caller is responsible for not playing with unimplemented bits */
+ if (i < 32) {
+ gpio_io_sel &= ~( 1 << i);
+ gpio_io_sel |= (val << i);
+ } else {
+ gpio_io_sel2 &= ~( 1 << (i - 32));
+ gpio_io_sel2 |= (val << (i - 32));
+ }
+ }
+ outl(gpio_io_sel, res->base + 0x04);
+ outl(gpio_io_sel2, res->base + 0x34);
+}
+
+static void set_i82801er_gpio_level(
+ device_t dev, struct resource *res, config_t *config)
+{
+ uint32_t gpio_lvl, gpio_lvl2;
+ uint32_t gpio_blink;
+ int i;
+
+ gpio_lvl = 0x1b3f0000;
+ gpio_blink = 0x00040000;
+ gpio_lvl2 = 0x00030207;
+ for(i = 0; i < 64; i++) {
+ int val, blink;
+ switch(config->gpio[i] & ICH5R_GPIO_LVL_MASK) {
+ case ICH5R_GPIO_LVL_LOW: val = 0; blink = 0; break;
+ case ICH5R_GPIO_LVL_HIGH: val = 1; blink = 0; break;
+ case ICH5R_GPIO_LVL_BLINK: val = 1; blink = 1; break;
+ default:
+ continue;
+ }
+ /* The caller is responsible for not playing with unimplemented bits */
+ if (i < 32) {
+ gpio_lvl &= ~( 1 << i);
+ gpio_blink &= ~( 1 << i);
+ gpio_lvl |= ( val << i);
+ gpio_blink |= (blink << i);
+ } else {
+ gpio_lvl2 &= ~( 1 << (i - 32));
+ gpio_lvl2 |= (val << (i - 32));
+ }
+ }
+ outl(gpio_lvl, res->base + 0x0c);
+ outl(gpio_blink, res->base + 0x18);
+ outl(gpio_lvl2, res->base + 0x38);
+}
+
+static void set_i82801er_gpio_inv(
+ device_t dev, struct resource *res, config_t *config)
+{
+ uint32_t gpio_inv;
+ int i;
+
+ gpio_inv = 0x00000000;
+ for(i = 0; i < 32; i++) {
+ int val;
+ switch(config->gpio[i] & ICH5R_GPIO_INV_MASK) {
+ case ICH5R_GPIO_INV_OFF: val = 0; break;
+ case ICH5R_GPIO_INV_ON: val = 1; break;
+ default:
+ continue;
+ }
+ gpio_inv &= ~( 1 << i);
+ gpio_inv |= (val << i);
+ }
+ outl(gpio_inv, res->base + 0x2c);
+}
+
+static void i82801er_pirq_init(device_t dev)
+{
+ config_t *config;
+
+ /* Get the chip configuration */
+ config = dev->chip_info;
+
+ if(config->pirq_a_d) {
+ pci_write_config32(dev, 0x60, config->pirq_a_d);
+ }
+ if(config->pirq_e_h) {
+ pci_write_config32(dev, 0x68, config->pirq_e_h);
+ }
+}
+
+
+static void i82801er_gpio_init(device_t dev)
+{
+ struct resource *res;
+ config_t *config;
+
+ /* Skip if I don't have any configuration */
+ if (!dev->chip_info) {
+ return;
+ }
+ /* The programmer is responsible for ensuring
+ * a valid gpio configuration.
+ */
+
+ /* Get the chip configuration */
+ config = dev->chip_info;
+ /* Find the GPIO bar */
+ res = find_resource(dev, GPIO_BAR);
+ if (!res) {
+ return;
+ }
+
+ /* Set the use selects */
+ set_i82801er_gpio_use_sel(dev, res, config);
+
+ /* Set the IO direction */
+ set_i82801er_gpio_direction(dev, res, config);
+
+ /* Setup the input inverters */
+ set_i82801er_gpio_inv(dev, res, config);
+
+ /* Set the value on the GPIO output pins */
+ set_i82801er_gpio_level(dev, res, config);
+
+}
+
+static void enable_hpet(struct device *dev)
+{
+const unsigned long hpet_address = 0xfed0000;
+
+ uint32_t dword;
+ uint32_t code = (0 & 0x3);
+
+ dword = pci_read_config32(dev, GEN_CNTL);
+ dword |= (1 << 17); /* enable hpet */
+
+ /* Bits [16:15] Memory Address Range
+ * 00 FED0_0000h - FED0_03FFh
+ * 01 FED0_1000h - FED0_13FFh
+ * 10 FED0_2000h - FED0_23FFh
+ * 11 FED0_3000h - FED0_33FFh
+ */
+
+ dword &= ~(3 << 15); /* clear it */
+ dword |= (code<<15);
+
+ printk_debug("enabling HPET @0x%x\n", hpet_address | (code <<12) );
+}
+
+static void lpc_init(struct device *dev)
+{
+ uint8_t byte;
+ uint32_t value;
+ int pwr_on=MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+
+ /* IO APIC initialization */
+ value = pci_read_config32(dev, 0xd0);
+ value |= (1 << 8)|(1<<7)|(1<<1);
+ pci_write_config32(dev, 0xd0, value);
+ value = pci_read_config32(dev, 0xd4);
+ value |= (1<<1);
+ pci_write_config32(dev, 0xd4, value);
+ setup_ioapic();
+
+ i82801er_enable_serial_irqs(dev);
+
+ i82801er_pci_dma_cfg(dev);
+
+ i82801er_enable_lpc(dev);
+
+ /* Clear SATA to non raid */
+ pci_write_config8(dev, 0xae, 0x00);
+
+ get_option(&pwr_on, "power_on_after_fail");
+ byte = pci_read_config8(dev, 0xa4);
+ byte &= 0xfe;
+ if (!pwr_on) {
+ byte |= 1;
+ }
+ pci_write_config8(dev, 0xa4, byte);
+ printk_info("set power %s after power fail\n", pwr_on?"on":"off");
+
+ /* Set up the PIRQ */
+ i82801er_pirq_init(dev);
+
+ /* Set the state of the gpio lines */
+ i82801er_gpio_init(dev);
+
+ /* Initialize the real time clock */
+ rtc_init(0);
+
+ /* Initialize isa dma */
+ isa_dma_init();
+
+ /* Disable IDE (needed when sata is enabled) */
+ pci_write_config8(dev, 0xf2, 0x60);
+
+ enable_hpet(dev);
+}
+
+static void i82801er_lpc_read_resources(device_t dev)
+{
+ struct resource *res;
+
+ /* Get the normal pci resources of this device */
+ pci_dev_read_resources(dev);
+
+ /* Add the ACPI BAR */
+ res = pci_get_resource(dev, ACPI_BAR);
+
+ /* Add the GPIO BAR */
+ res = pci_get_resource(dev, GPIO_BAR);
+
+ /* Add an extra subtractive resource for both memory and I/O */
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0));
+ res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;
+
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0));
+ res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;
+}
+
+static void i82801er_lpc_enable_resources(device_t dev)
+{
+ uint8_t acpi_cntl, gpio_cntl;
+
+ /* Enable the normal pci resources */
+ pci_dev_enable_resources(dev);
+
+ /* Enable the ACPI bar */
+ acpi_cntl = pci_read_config8(dev, 0x44);
+ acpi_cntl |= (1 << 4);
+ pci_write_config8(dev, 0x44, acpi_cntl);
+
+ /* Enable the GPIO bar */
+ gpio_cntl = pci_read_config8(dev, 0x5c);
+ gpio_cntl |= (1 << 4);
+ pci_write_config8(dev, 0x5c, gpio_cntl);
+
+ enable_childrens_resources(dev);
+}
+
+static struct pci_operations lops_pci = {
+ .set_subsystem = 0,
+};
+
+static struct device_operations lpc_ops = {
+ .read_resources = i82801er_lpc_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = i82801er_lpc_enable_resources,
+ .init = lpc_init,
+ .scan_bus = scan_static_bus,
+ .enable = i82801er_enable,
+ .ops_pci = &lops_pci,
+};
+
+static struct pci_driver lpc_driver __pci_driver = {
+ .ops = &lpc_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_82801ER_ISA,
+};