/*
 * This file is part of the coreboot project.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

#include <stdint.h>
#include <string.h>
#include <device/pci_def.h>
#include <device/pci_ids.h>
#include <arch/io.h>
#include <device/pnp_def.h>
#include <cpu/x86/lapic.h>
#include <pc80/mc146818rtc.h>
#include <console/console.h>
#include <lib.h>
#include <spd.h>
#include <cpu/amd/model_fxx_rev.h>
#include "southbridge/nvidia/mcp55/early_smbus.c" // for enable the FAN
#include <northbridge/amd/amdk8/raminit.h>
#include "lib/delay.c"
#include <cpu/x86/lapic.h>
#include "northbridge/amd/amdk8/reset_test.c"
#include <superio/winbond/common/winbond.h>
#include <superio/winbond/w83627hf/w83627hf.h>
#include <cpu/x86/bist.h>
#include "northbridge/amd/amdk8/debug.c"
#include "northbridge/amd/amdk8/setup_resource_map.c"
#include "southbridge/nvidia/mcp55/early_ctrl.c"

#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
#define DUMMY_DEV PNP_DEV(0x2e, 0)

static void memreset(int controllers, const struct mem_controller *ctrl) { }

static inline void activate_spd_rom(const struct mem_controller *ctrl)
{
#if 0
/* We don't do any switching yet. */
#define SMBUS_SWITCH1 0x48
#define SMBUS_SWITCH2 0x49
	unsigned device=(ctrl->channel0[0])>>8;
	smbus_send_byte(SMBUS_SWITCH1, device);
	smbus_send_byte(SMBUS_SWITCH2, (device >> 4) & 0x0f);
#endif
}

static inline int spd_read_byte(unsigned device, unsigned address)
{
	return smbus_read_byte(device, address);
}

#include <northbridge/amd/amdk8/f.h>
#include "northbridge/amd/amdk8/incoherent_ht.c"
#include "northbridge/amd/amdk8/coherent_ht.c"
#include "northbridge/amd/amdk8/raminit_f.c"
#include "lib/generic_sdram.c"
#include "resourcemap.c"
#include "cpu/amd/dualcore/dualcore.c"
#include <southbridge/nvidia/mcp55/early_setup_ss.h>
#include "southbridge/nvidia/mcp55/early_setup_car.c"
#include "cpu/amd/model_fxx/init_cpus.c"
#include "cpu/amd/model_fxx/fidvid.c"
#include "northbridge/amd/amdk8/early_ht.c"

static void sio_setup(void)
{
	uint32_t dword;
	uint8_t byte;

	enable_smbus();
//      smbusx_write_byte(1, (0x58>>1), 0, 0x80); /* select bank0 */
	smbusx_write_byte(1, (0x58 >> 1), 0xb1, 0xff);	/* set FAN ctrl to DC mode */

	byte = pci_read_config8(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0x7b);
	byte |= 0x20;
	pci_write_config8(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0x7b, byte);

	dword = pci_read_config32(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0xa0);
	dword |= (1 << 0);
	pci_write_config32(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0xa0, dword);

	dword = pci_read_config32(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0xa4);
	dword |= (1 << 16);
	pci_write_config32(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0xa4, dword);
}

/* We have no idea where the SMBUS switch is. This doesn't do anything ATM. */
#define RC0 (2<<8)
#define RC1 (1<<8)

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
/* The SPD is being read from the CPU1 (marked CPU2 on the board) and we
   don't know how to switch the SMBus to decode the CPU0 SPDs. So, The
   memory on each CPU must be an exact match.
 */
	static const uint16_t spd_addr[] = {
		// Node 0
		RC0 | DIMM0, RC0 | DIMM2,
		RC0 | DIMM4, RC0 | DIMM6,
		RC0 | DIMM1, RC0 | DIMM3,
		RC0 | DIMM5, RC0 | DIMM7,
		// Node 1
		RC1 | DIMM0, RC1 | DIMM2,
		RC1 | DIMM4, RC1 | DIMM6,
		RC1 | DIMM1, RC1 | DIMM3,
		RC1 | DIMM5, RC1 | DIMM7,
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	w83627hf_set_clksel_48(DUMMY_DEV);
	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

	setup_mb_resource_map();

	printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);

	set_sysinfo_in_ram(0);	// in BSP so could hold all ap until sysinfo is in ram
#if CONFIG_DEBUG_SMBUS
	dump_smbus_registers();
#endif
	setup_coherent_ht_domain();	// routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
	// It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
	ht_setup_chains_x(sysinfo);	// it will init sblnk and sbbusn, nodes, sbdn

#if CONFIG_SET_FIDVID
	{
		msr_t msr;
		msr = rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
	}
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
	init_fidvid_bsp(bsp_apicid);
	// show final fid and vid
	{
		msr_t msr;
		msr = rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end   msr fid, vid %08x%08x\n", msr.hi, msr.lo);
	}
#endif

	init_timer(); /* Need to use TMICT to synchronize FID/VID. */

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

	// fidvid change will issue one LDTSTOP and the HT change will be effective too
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	//It's the time to set ctrl in sysinfo now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();		/* enable in sio_setup */

	/* all ap stopped? */

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	post_cache_as_ram();	// bsp swtich stack to ram and copy sysinfo ram now
}