blob: 456e6661a1687072d11e5f8d8b4bb400cf32c36d [file] [log] [blame]
chip soc/intel/cannonlake
register "SerialIoDevMode" = "{
[PchSerialIoIndexI2C0] = PchSerialIoDisabled,
[PchSerialIoIndexI2C1] = PchSerialIoDisabled,
[PchSerialIoIndexI2C2] = PchSerialIoPci,
[PchSerialIoIndexI2C3] = PchSerialIoPci,
[PchSerialIoIndexI2C4] = PchSerialIoPci,
[PchSerialIoIndexI2C5] = PchSerialIoPci,
[PchSerialIoIndexSPI0] = PchSerialIoPci,
[PchSerialIoIndexSPI1] = PchSerialIoPci,
[PchSerialIoIndexSPI2] = PchSerialIoDisabled,
[PchSerialIoIndexUART0] = PchSerialIoSkipInit,
[PchSerialIoIndexUART1] = PchSerialIoDisabled,
[PchSerialIoIndexUART2] = PchSerialIoDisabled,
}"
# USB configuration
register "usb2_ports[0]" = "USB2_PORT_MID(OC2)" # Type-A Port 2
register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C Port
register "usb2_ports[2]" = "{
.enable = 1,
.ocpin = OC3,
.tx_bias = USB2_BIAS_0MV,
.tx_emp_enable = USB2_PRE_EMP_ON,
.pre_emp_bias = USB2_BIAS_28P15MV,
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP,
}" # Type-A Port 3
register "usb2_ports[3]" = "{
.enable = 1,
.ocpin = OC1,
.tx_bias = USB2_BIAS_0MV,
.tx_emp_enable = USB2_PRE_EMP_ON,
.pre_emp_bias = USB2_BIAS_28P15MV,
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP,
}" # Type-A Port 1
register "usb2_ports[4]" = "{
.enable = 1,
.ocpin = OC_SKIP,
.tx_bias = USB2_BIAS_0MV,
.tx_emp_enable = USB2_PRE_EMP_ON,
.pre_emp_bias = USB2_BIAS_28P15MV,
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP,
}" # Type-A Port 4
register "usb2_ports[5]" = "{
.enable = 1,
.ocpin = OC0,
.tx_bias = USB2_BIAS_0MV,
.tx_emp_enable = USB2_PRE_EMP_ON,
.pre_emp_bias = USB2_BIAS_28P15MV,
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP,
}" # Type-A port 0
register "usb2_ports[6]" = "USB2_PORT_EMPTY"
register "usb2_ports[7]" = "USB2_PORT_EMPTY"
register "usb2_ports[8]" = "USB2_PORT_EMPTY"
register "usb2_ports[9]" = "{
.enable = 1,
.ocpin = OC_SKIP,
.tx_bias = USB2_BIAS_0MV,
.tx_emp_enable = USB2_PRE_EMP_ON,
.pre_emp_bias = USB2_BIAS_28P15MV,
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP,
}" # BT
register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port 2
register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port 3
register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Port 1
register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C
register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC0)" # Type-A Port 0
register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A Port 4
# Enable eMMC HS400
register "ScsEmmcHs400Enabled" = "1"
# EMMC Tx CMD Delay
# Refer to EDS-Vol2-14.3.7.
# [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39.
# [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39.
register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505"
# EMMC TX DATA Delay 1
# Refer to EDS-Vol2-14.3.8.
# [14:8] steps of delay for HS400, each 125ps, range: 0 - 78.
# [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79.
register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x911"
# EMMC TX DATA Delay 2
# Refer to EDS-Vol2-14.3.9.
# [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79.
# [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78.
# [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79.
# [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79.
register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C262828"
# EMMC RX CMD/DATA Delay 1
# Refer to EDS-Vol2-14.3.10.
# [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119.
# [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78.
# [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119.
# [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119.
register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C16583b"
# EMMC RX CMD/DATA Delay 2
# Refer to EDS-Vol2-14.3.12.
# [17:16] stands for Rx Clock before Output Buffer,
# 00: Rx clock after output buffer,
# 01: Rx clock before output buffer,
# 10: Automatic selection based on working mode.
# 11: Reserved
# [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39.
# [6:0] steps of delay for HS200, each 125ps, range: 0 - 79.
register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x1001D"
# EMMC Rx Strobe Delay
# Refer to EDS-Vol2-14.3.11.
# [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39.
# [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39.
register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x1515"
# Intel HDA - disable I2S Audio SSP1 and DMIC0 as puff variant does not have them.
register "PchHdaAudioLinkSsp1" = "0"
register "PchHdaAudioLinkDmic0" = "0"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| GSPI0 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| | before memory is up |
#| I2C0 | RFU |
#| I2C2 | PS175 |
#| I2C3 | MST |
#| I2C4 | Audio |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.gspi[0] = {
.speed_mhz = 1,
.early_init = 1,
},
.i2c[0] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 0,
.fall_time_ns = 0,
},
.i2c[2] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 0,
.fall_time_ns = 0,
},
.i2c[3] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 0,
.fall_time_ns = 0,
},
.i2c[4] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 0,
.fall_time_ns = 0,
},
}"
# PCIe port 7 for LAN
register "PcieRpEnable[6]" = "1"
register "PcieRpLtrEnable[6]" = "1"
# Uses CLK SRC 0
register "PcieClkSrcUsage[0]" = "6"
register "PcieClkSrcClkReq[0]" = "0"
# GPIO for SD card detect
register "sdcard_cd_gpio" = "vSD3_CD_B"
# SATA port 1 Gen3 Strength
# Port1 Tx De-Emphasis = 20*log(0x20/64) = -6dB
register "sata_port[1].TxGen3DeEmphEnable" = "1"
register "sata_port[1].TxGen3DeEmph" = "0x20"
device domain 0 on
device pci 14.0 on
chip drivers/usb/acpi
device usb 0.0 on
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Front Left""
register "type" = "UPC_TYPE_A"
device usb 2.0 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port Rear""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
device usb 2.1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Front Right""
register "type" = "UPC_TYPE_A"
device usb 2.2 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Rear Right""
register "type" = "UPC_TYPE_A"
device usb 2.3 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Rear Middle""
register "type" = "UPC_TYPE_A"
device usb 2.4 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Rear Left""
register "type" = "UPC_TYPE_A"
device usb 2.5 on end
end
chip drivers/usb/acpi
device usb 2.6 off end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Front Left""
register "type" = "UPC_TYPE_USB3_A"
device usb 3.0 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Front Right""
register "type" = "UPC_TYPE_USB3_A"
device usb 3.1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Rear Right""
register "type" = "UPC_TYPE_USB3_A"
device usb 3.2 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Rear""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
device usb 3.3 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Rear Left""
register "type" = "UPC_TYPE_USB3_A"
device usb 3.4 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Rear Middle""
register "type" = "UPC_TYPE_USB3_A"
device usb 3.5 on end
end
end
end
end # USB xHCI
device pci 15.0 off
# RFU - Reserved for Future Use.
end # I2C #0
device pci 15.1 off end # I2C #1
device pci 15.2 on end # I2C #2, PCON PS175.
device pci 15.3 on end # I2C #3, Realtek RTD2142.
device pci 19.0 on
chip drivers/i2c/generic
register "hid" = ""10EC5682""
register "name" = ""RT58""
register "desc" = ""Realtek RT5682""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_H0)"
register "property_count" = "1"
# Set the jd_src to RT5668_JD1 for jack detection
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on end
end
end #I2C #4
device pci 1a.0 on end # eMMC
device pci 1c.0 on
chip drivers/net
register "customized_leds" = "0x05af"
device pci 00.0 on end
end
end # FSP requires func0 be enabled.
device pci 1c.6 on end # RTL8111H Ethernet NIC (becomes RP1).
device pci 1e.3 off end # GSPI #1
end
# VR Settings Configuration for 4 Domains
#+----------------+-------+-------+-------+-------+
#| Domain/Setting | SA | IA | GTUS | GTS |
#+----------------+-------+-------+-------+-------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 5A | 5A | 5A | 5A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#| AcLoadline | 10.04 | 1.81 | 3.19 | 3.19 |
#| DcLoadline | 10.04 | 1.81 | 3.19 | 3.19 |
#+----------------+-------+-------+-------+-------+
#Note: IccMax settings are moved to SoC code
register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = 0,
.voltage_limit = 1520,
.ac_loadline = 1004,
.dc_loadline = 1004,
}"
register "domain_vr_config[VR_IA_CORE]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = 0,
.voltage_limit = 1520,
.ac_loadline = 181,
.dc_loadline = 181,
}"
register "domain_vr_config[VR_GT_UNSLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = 0,
.voltage_limit = 1520,
.ac_loadline = 319,
.dc_loadline = 319,
}"
register "domain_vr_config[VR_GT_SLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = 0,
.voltage_limit = 1520,
.ac_loadline = 319,
.dc_loadline = 319,
}"
end