/** @file

Copyright (c) 2023, Intel Corporation. All rights reserved.<BR>

Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this
  list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
  list of conditions and the following disclaimer in the documentation and/or
  other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
  be used to endorse or promote products derived from this software without
  specific prior written permission.

  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
  THE POSSIBILITY OF SUCH DAMAGE.

  This file is automatically generated. Please do NOT modify !!!

**/

#ifndef __FSPMUPD_H__
#define __FSPMUPD_H__

#include <FspUpd.h>

#pragma pack(1)


#include <MemInfoHob.h>

///
/// The ChipsetInit Info structure provides the information of ME ChipsetInit CRC and BIOS ChipsetInit CRC.
///
typedef struct {
  UINT8             Revision;         ///< Chipset Init Info Revision
  UINT8             Rsvd[3];          ///< Reserved
  UINT16            MeChipInitCrc;    ///< 16 bit CRC value of MeChipInit Table
  UINT16            BiosChipInitCrc;  ///< 16 bit CRC value of PchChipInit Table
} CHIPSET_INIT_INFO;


/** Fsp M Configuration
**/
typedef struct {

/** Offset 0x0040 - Platform Reserved Memory Size
  The minimum platform memory size required to pass control into DXE
**/
  UINT64                      PlatformMemorySize;

/** Offset 0x0048 - SPD Data Length
  Length of SPD Data
  0x100:256 Bytes, 0x200:512 Bytes, 0x400:1024 Bytes
**/
  UINT16                      MemorySpdDataLen;

/** Offset 0x004A - Enable above 4GB MMIO resource support
  Enable/disable above 4GB MMIO resource support
  $EN_DIS
**/
  UINT8                       EnableAbove4GBMmio;

/** Offset 0x004B - Reserved
**/
  UINT8                       Reserved0;

/** Offset 0x004C - Memory SPD Pointer Controller 0 Channel 0 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr000;

/** Offset 0x0050 - Memory SPD Pointer Controller 0 Channel 0 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr001;

/** Offset 0x0054 - Memory SPD Pointer Controller 0 Channel 1 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr010;

/** Offset 0x0058 - Memory SPD Pointer Controller 0 Channel 1 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr011;

/** Offset 0x005C - Memory SPD Pointer Controller 0 Channel 2 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr020;

/** Offset 0x0060 - Memory SPD Pointer Controller 0 Channel 2 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr021;

/** Offset 0x0064 - Memory SPD Pointer Controller 0 Channel 3 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr030;

/** Offset 0x0068 - Memory SPD Pointer Controller 0 Channel 3 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr031;

/** Offset 0x006C - Memory SPD Pointer Controller 1 Channel 0 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr100;

/** Offset 0x0070 - Memory SPD Pointer Controller 1 Channel 0 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr101;

/** Offset 0x0074 - Memory SPD Pointer Controller 1 Channel 1 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr110;

/** Offset 0x0078 - Memory SPD Pointer Controller 1 Channel 1 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr111;

/** Offset 0x007C - Memory SPD Pointer Controller 1 Channel 2 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr120;

/** Offset 0x0080 - Memory SPD Pointer Controller 1 Channel 2 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr121;

/** Offset 0x0084 - Memory SPD Pointer Controller 1 Channel 3 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr130;

/** Offset 0x0088 - Memory SPD Pointer Controller 1 Channel 3 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr131;

/** Offset 0x008C - RcompResistor settings
  Indicates  RcompResistor settings: Board-dependent
**/
  UINT16                      RcompResistor;

/** Offset 0x008E - RcompTarget settings
  RcompTarget settings: board-dependent
**/
  UINT16                      RcompTarget[5];

/** Offset 0x0098 - Dqs Map CPU to DRAM MC 0 CH 0
  Set Dqs mapping relationship between CPU and DRAM, Channel 0: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc0Ch0[2];

/** Offset 0x009A - Dqs Map CPU to DRAM MC 0 CH 1
  Set Dqs mapping relationship between CPU and DRAM, Channel 1: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc0Ch1[2];

/** Offset 0x009C - Dqs Map CPU to DRAM MC 0 CH 2
  Set Dqs mapping relationship between CPU and DRAM, Channel 2: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc0Ch2[2];

/** Offset 0x009E - Dqs Map CPU to DRAM MC 0 CH 3
  Set Dqs mapping relationship between CPU and DRAM, Channel 3: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc0Ch3[2];

/** Offset 0x00A0 - Dqs Map CPU to DRAM MC 1 CH 0
  Set Dqs mapping relationship between CPU and DRAM, Channel 0: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc1Ch0[2];

/** Offset 0x00A2 - Dqs Map CPU to DRAM MC 1 CH 1
  Set Dqs mapping relationship between CPU and DRAM, Channel 1: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc1Ch1[2];

/** Offset 0x00A4 - Dqs Map CPU to DRAM MC 1 CH 2
  Set Dqs mapping relationship between CPU and DRAM, Channel 2: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc1Ch2[2];

/** Offset 0x00A6 - Dqs Map CPU to DRAM MC 1 CH 3
  Set Dqs mapping relationship between CPU and DRAM, Channel 3: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc1Ch3[2];

/** Offset 0x00A8 - Dq Map CPU to DRAM MC 0 CH 0
  Set Dq mapping relationship between CPU and DRAM, Channel 0: board-dependent
**/
  UINT8                       DqMapCpu2DramMc0Ch0[16];

/** Offset 0x00B8 - Dq Map CPU to DRAM MC 0 CH 1
  Set Dq mapping relationship between CPU and DRAM, Channel 1: board-dependent
**/
  UINT8                       DqMapCpu2DramMc0Ch1[16];

/** Offset 0x00C8 - Dq Map CPU to DRAM MC 0 CH 2
  Set Dq mapping relationship between CPU and DRAM, Channel 2: board-dependent
**/
  UINT8                       DqMapCpu2DramMc0Ch2[16];

/** Offset 0x00D8 - Dq Map CPU to DRAM MC 0 CH 3
  Set Dq mapping relationship between CPU and DRAM, Channel 3: board-dependent
**/
  UINT8                       DqMapCpu2DramMc0Ch3[16];

/** Offset 0x00E8 - Dq Map CPU to DRAM MC 1 CH 0
  Set Dq mapping relationship between CPU and DRAM, Channel 0: board-dependent
**/
  UINT8                       DqMapCpu2DramMc1Ch0[16];

/** Offset 0x00F8 - Dq Map CPU to DRAM MC 1 CH 1
  Set Dq mapping relationship between CPU and DRAM, Channel 1: board-dependent
**/
  UINT8                       DqMapCpu2DramMc1Ch1[16];

/** Offset 0x0108 - Dq Map CPU to DRAM MC 1 CH 2
  Set Dq mapping relationship between CPU and DRAM, Channel 2: board-dependent
**/
  UINT8                       DqMapCpu2DramMc1Ch2[16];

/** Offset 0x0118 - Dq Map CPU to DRAM MC 1 CH 3
  Set Dq mapping relationship between CPU and DRAM, Channel 3: board-dependent
**/
  UINT8                       DqMapCpu2DramMc1Ch3[16];

/** Offset 0x0128 - Dqs Pins Interleaved Setting
  Indicates DqPinsInterleaved setting: board-dependent
  $EN_DIS
**/
  UINT8                       DqPinsInterleaved;

/** Offset 0x0129 - Smram Mask
  The SMM Regions AB-SEG and/or H-SEG reserved
  0: Neither, 1:AB-SEG, 2:H-SEG, 3: Both
**/
  UINT8                       SmramMask;

/** Offset 0x012A - MRC Fast Boot
  Enables/Disable the MRC fast path thru the MRC
  $EN_DIS
**/
  UINT8                       MrcFastBoot;

/** Offset 0x012B - Rank Margin Tool per Task
  This option enables the user to execute Rank Margin Tool per major training step
  in the MRC.
  $EN_DIS
**/
  UINT8                       RmtPerTask;

/** Offset 0x012C - Training Trace
  This option enables the trained state tracing feature in MRC.  This feature will
  print out the key training parameters state across major training steps.
  $EN_DIS
**/
  UINT8                       TrainTrace;

/** Offset 0x012D - Reserved
**/
  UINT8                       Reserved1[3];

/** Offset 0x0130 - Tseg Size
  Size of SMRAM memory reserved. 0x400000 for Release build and 0x1000000 for Debug build
  0x0400000:4MB, 0x01000000:16MB
**/
  UINT32                      TsegSize;

/** Offset 0x0134 - MMIO Size
  Size of MMIO space reserved for devices. 0(Default)=Auto, non-Zero=size in MB
**/
  UINT16                      MmioSize;

/** Offset 0x0136 - Probeless Trace
  Probeless Trace: 0=Disabled, 1=Enable. Enabling Probeless Trace will reserve 128MB.
  This also requires IED to be enabled.
  $EN_DIS
**/
  UINT8                       ProbelessTrace;

/** Offset 0x0137 - Enable SMBus
  Enable/disable SMBus controller.
  $EN_DIS
**/
  UINT8                       SmbusEnable;

/** Offset 0x0138 - Spd Address Tabl
  Specify SPD Address table for CH0D0/CH0D1/CH1D0&CH1D1. MemorySpdPtr will be used
  if SPD Address is 00
**/
  UINT8                       SpdAddressTable[16];

/** Offset 0x0148 - Platform Debug Consent
  Enabled Trace active: TraceHub is enabled and trace is active, blocks s0ix.\n
  \n
  Enabled Trace ready: TraceHub is enabled and allowed S0ix.\n
  \n
  Enabled Trace power off: TraceHub is powergated, provide setting close to functional
  low power state\n
  \n
  Manual: user needs to configure Advanced Debug Settings manually, aimed at advanced users
  0:Disabled, 2:Enabled Trace Active, 4:Enabled Trace Ready, 6:Enable Trace Power-Off, 7:Manual
**/
  UINT8                       PlatformDebugOption;

/** Offset 0x0149 - DCI Enable
  Determine if to enable DCI debug from host
  $EN_DIS
**/
  UINT8                       DciEn;

/** Offset 0x014A - Reserved
**/
  UINT8                       Reserved2;

/** Offset 0x014B - DCI DbC Mode
  Disabled: Clear both USB2/3DBCEN; USB2: set USB2DBCEN; USB3: set USB3DBCEN; Both:
  Set both USB2/3DBCEN; No Change: Comply with HW value
  0:Disabled, 1:USB2 DbC, 2:USB3 DbC, 3:Both, 4:No Change
**/
  UINT8                       DciDbcMode;

/** Offset 0x014C - USB3 Type-C UFP2DFP Kernel/Platform Debug Support
  This BIOS option enables kernel and platform debug for USB3 interface over a UFP
  Type-C receptacle, select 'No Change' will do nothing to UFP2DFP setting.
  0:Disabled, 1:Enabled, 2:No Change
**/
  UINT8                       DciUsb3TypecUfpDbg;

/** Offset 0x014D - SOC Trace Hub Mode
  Enable/Disable SOC TraceHub
  $EN_DIS
**/
  UINT8                       SocTraceHubMode;

/** Offset 0x014E - SOC Trace Hub Memory Region 0 buffer Size
  Select size of memory region 0 buffer. Memory allocated by BIOS only applies to
  ITH tool running on the host. For ITH tool running on the target, choose None/OS,
  memory shall be allocated by tool. User should be cautious to choose the amount
  of memory. If chosen size is larger than half of system memory, setup will automatically
  rollback to default value.
  0x00:1MB, 0x03:8MB, 0x06:64MB, 0x07:128MB, 0x08:256MB, 0x09:512MB, 0x0A:1GB, 0x0B:2GB,
  0x0C:4GB, 0x0D:8GB, 0x0E:0MB
**/
  UINT16                      SocTraceHubMemReg0Size;

/** Offset 0x0150 - SOC Trace Hub Memory Region 1 buffer Size
  Select size of memory region 1 buffer. Memory allocated by BIOS only applies to
  ITH tool running on the host. For ITH tool running on the target, choose None/OS,
  memory shall be allocated by tool. User should be cautious to choose the amount
  of memory. If chosen size is larger than half of system memory, setup will automatically
  rollback to default value.
  0x00:1MB, 0x03:8MB, 0x06:64MB, 0x07:128MB, 0x08:256MB, 0x09:512MB, 0x0A:1GB, 0x0B:2GB,
  0x0C:4GB, 0x0D:8GB, 0x0E:0MB
**/
  UINT16                      SocTraceHubMemReg1Size;

/** Offset 0x0152 - Reserved
**/
  UINT8                       Reserved3;

/** Offset 0x0153 - PCH Trace Hub Mode
  Enable/Disable PCH TraceHub
  $EN_DIS
**/
  UINT8                       PchTraceHubMode;

/** Offset 0x0154 - PCH Trace Hub Memory Region 0 buffer Size
  Select size of memory region 0 buffer. Memory allocated by BIOS only applies to
  ITH tool running on the host. For ITH tool running on the target, choose None/OS,
  memory shall be allocated by tool. User should be cautious to choose the amount
  of memory. If chosen size is larger than half of system memory, setup will automatically
  rollback to default value.
  0x00:1MB, 0x03:8MB, 0x06:64MB, 0x07:128MB, 0x08:256MB, 0x09:512MB, 0x0A:1GB, 0x0B:2GB,
  0x0C:4GB, 0x0D:8GB, 0x0E:0MB
**/
  UINT16                      PchTraceHubMemReg0Size;

/** Offset 0x0156 - PCH Trace Hub Memory Region 1 buffer Size
  Select size of memory region 1 buffer. Memory allocated by BIOS only applies to
  ITH tool running on the host. For ITH tool running on the target, choose None/OS,
  memory shall be allocated by tool. User should be cautious to choose the amount
  of memory. If chosen size is larger than half of system memory, setup will automatically
  rollback to default value.
  0x00:1MB, 0x03:8MB, 0x06:64MB, 0x07:128MB, 0x08:256MB, 0x09:512MB, 0x0A:1GB, 0x0B:2GB,
  0x0C:4GB, 0x0D:8GB, 0x0E:0MB
**/
  UINT16                      PchTraceHubMemReg1Size;

/** Offset 0x0158 - Reserved
**/
  UINT8                       Reserved4[4];

/** Offset 0x015C - HD Audio DMIC Link Clock Select
  Determines DMIC<N> Clock Source. 0: Both, 1: ClkA, 2: ClkB
  0: Both, 1: ClkA, 2: ClkB
**/
  UINT8                       PchHdaAudioLinkDmicClockSelect[2];

/** Offset 0x015E - State of X2APIC_OPT_OUT bit in the DMAR table
  0=Disable/Clear, 1=Enable/Set
  $EN_DIS
**/
  UINT8                       X2ApicOptOut;

/** Offset 0x015F - State of DMA_CONTROL_GUARANTEE bit in the DMAR table
  0=Disable/Clear, 1=Enable/Set
  $EN_DIS
**/
  UINT8                       DmaControlGuarantee;

/** Offset 0x0160 - Base addresses for VT-d function MMIO access
  Base addresses for VT-d MMIO access per VT-d engine
**/
  UINT32                      VtdBaseAddress[9];

/** Offset 0x0184 - Disable VT-d
  0=Enable/FALSE(VT-d enabled), 1=Disable/TRUE (VT-d disabled)
  $EN_DIS
**/
  UINT8                       VtdDisable;

/** Offset 0x0185 - Vtd Programming for Igd
  1=Enable/TRUE (Igd VT-d Bar programming enabled), 0=Disable/FLASE (Igd VT-d Bar
  programming disabled)
  $EN_DIS
**/
  UINT8                       VtdIgdEnable;

/** Offset 0x0186 - Vtd Programming for Iop
  1=Enable/TRUE (Iop VT-d Bar programming enabled), 0=Disable/FLASE (Iop VT-d Bar
  programming disabled)
  $EN_DIS
**/
  UINT8                       VtdIopEnable;

/** Offset 0x0187 - Internal Graphics Pre-allocated Memory
  Size of memory preallocated for internal graphics.
  0x00:0MB, 0x01:32MB, 0x02:64MB, 0x03:96MB, 0x04:128MB, 0xF0:4MB, 0xF1:8MB, 0xF2:12MB,
  0xF3:16MB, 0xF4:20MB, 0xF5:24MB, 0xF6:28MB, 0xF7:32MB, 0xF8:36MB, 0xF9:40MB, 0xFA:44MB,
  0xFB:48MB, 0xFC:52MB, 0xFD:56MB, 0xFE:60MB
**/
  UINT8                       IgdDvmt50PreAlloc;

/** Offset 0x0188 - Internal Graphics
  Enable/disable internal graphics.
  $EN_DIS
**/
  UINT8                       InternalGfx;

/** Offset 0x0189 - Reserved
**/
  UINT8                       Reserved5;

/** Offset 0x018A - Board Type
  MrcBoardType, Options are 0=Mobile/Mobile Halo, 1=Desktop/DT Halo, 5=ULT/ULX/Mobile
  Halo, 7=UP Server
  0:Mobile/Mobile Halo, 1:Desktop/DT Halo, 5:ULT/ULX/Mobile Halo, 7:UP Server
**/
  UINT8                       UserBd;

/** Offset 0x018B - Reserved
**/
  UINT8                       Reserved6;

/** Offset 0x018C - DDR Frequency Limit
  Maximum Memory Frequency Selections in Mhz. Options are 1067, 1333, 1600, 1867,
  2133, 2400, 2667, 2933 and 0 for Auto.
  1067:1067, 1333:1333, 1600:1600, 1867:1867, 2133:2133, 2400:2400, 2667:2667, 2933:2933, 0:Auto
**/
  UINT16                      DdrFreqLimit;

/** Offset 0x018E - SAGV
  System Agent dynamic frequency support.
  0:Disabled, 1:Enabled
**/
  UINT8                       SaGv;

/** Offset 0x018F - SAGV WP Mask
  System Agent dynamic frequency workpoints that memory will be training at the enabled
  frequencies.
  0x3:Points0_1, 0x7:Points0_1_2, 0xF:AllPoints0_1_2_3
**/
  UINT8                       SaGvWpMask;

/** Offset 0x0190 - Memory Test on Warm Boot
  Run Base Memory Test on Warm Boot
  0:Disable, 1:Enable
**/
  UINT8                       MemTestOnWarmBoot;

/** Offset 0x0191 - DDR Speed Control
  DDR Frequency and Gear control for all SAGV points.
  0:Auto, 1:Manual
**/
  UINT8                       DdrSpeedControl;

/** Offset 0x0192 - Controller 0 Channel 0 DIMM Control
  Enable / Disable DIMMs on Controller 0 Channel 0
  $EN_DIS
**/
  UINT8                       DisableMc0Ch0;

/** Offset 0x0193 - Controller 0 Channel 1 DIMM Control
  Enable / Disable DIMMs on Controller 0 Channel 1
  $EN_DIS
**/
  UINT8                       DisableMc0Ch1;

/** Offset 0x0194 - Controller 0 Channel 2 DIMM Control
  Enable / Disable DIMMs on Controller 0 Channel 2
  $EN_DIS
**/
  UINT8                       DisableMc0Ch2;

/** Offset 0x0195 - Controller 0 Channel 3 DIMM Control
  Enable / Disable DIMMs on Controller 0 Channel 3
  $EN_DIS
**/
  UINT8                       DisableMc0Ch3;

/** Offset 0x0196 - Controller 1 Channel 0 DIMM Control
  Enable / Disable DIMMs on Controller 1 Channel 0
  $EN_DIS
**/
  UINT8                       DisableMc1Ch0;

/** Offset 0x0197 - Controller 1 Channel 1 DIMM Control
  Enable / Disable DIMMs on Controller 1 Channel 1
  $EN_DIS
**/
  UINT8                       DisableMc1Ch1;

/** Offset 0x0198 - Controller 1 Channel 2 DIMM Control
  Enable / Disable DIMMs on Controller 1 Channel 2
  $EN_DIS
**/
  UINT8                       DisableMc1Ch2;

/** Offset 0x0199 - Controller 1 Channel 3 DIMM Control
  Enable / Disable DIMMs on Controller 1 Channel 3
  $EN_DIS
**/
  UINT8                       DisableMc1Ch3;

/** Offset 0x019A - Scrambler Support
  This option enables data scrambling in memory.
  $EN_DIS
**/
  UINT8                       ScramblerSupport;

/** Offset 0x019B - SPD Profile Selected
  Select DIMM timing profile. Options are 0:Default SPD Profile, 1:Custom Profile,
  2:XMP Profile 1, 3:XMP Profile 2, 4:XMP Profile 3, 5:XMP User Profile 4, 6:XMP
  User Profile 5
  0:Default SPD Profile, 1:Custom Profile, 2:XMP Profile 1, 3:XMP Profile 2, 4:XMP
  Profile 3, 5:XMP User Profile 4, 6:XMP User Profile 5
**/
  UINT8                       SpdProfileSelected;

/** Offset 0x019C - Reserved
**/
  UINT8                       Reserved7[102];

/** Offset 0x0202 - Memory Reference Clock
  100MHz, 133MHz.
  0:133MHz, 1:100MHz
**/
  UINT8                       RefClk;

/** Offset 0x0203 - Reserved
**/
  UINT8                       Reserved8[9];

/** Offset 0x020C - Memory Vdd Voltage
  DRAM voltage (Vdd) (supply voltage for input buffers and core logic of the DRAM
  chips) in millivolts. <b>0=Platform Default (no override)</b>, 1200=1.2V, 1350=1.35V etc.
  0:Default, 1200:1.20 Volts, 1250:1.25 Volts, 1300:1.30 Volts, 1350:1.35 Volts, 1400:1.40
  Volts, 1450:1.45 Volts, 1500:1.50 Volts, 1550:1.55 Volts, 1600:1.60 Volts, 1650:1.65 Volts
**/
  UINT16                      VddVoltage;

/** Offset 0x020E - Reserved
**/
  UINT8                      Reserved9[4];

/** Offset 0x0212 - Memory Ratio
  Automatic or the frequency will equal ratio times reference clock. Set to Auto to
  recalculate memory timings listed below.
  0:Auto, 4:4, 5:5, 6:6, 7:7, 8:8, 9:9, 10:10, 11:11, 12:12, 13:13, 14:14, 15:15
**/
  UINT16                      Ratio;

/** Offset 0x0214 - tCL
  CAS Latency, 0: AUTO, max: 255. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT8                       tCL;

/** Offset 0x0215 - tCWL
  Min CAS Write Latency Delay Time, 0: AUTO, max: 255. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT8                       tCWL;

/** Offset 0x0216 - tFAW
  Min Four Activate Window Delay Time, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT16                      tFAW;

/** Offset 0x0218 - tRAS
  RAS Active Time, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT16                      tRAS;

/** Offset 0x021A - tRCD/tRP
  RAS to CAS delay time and Row Precharge delay time, 0: AUTO, max: 255. Only used
  if FspmUpd->FspmConfig.SpdProfileSelected == 1 (Custom Profile).
**/
  UINT8                       tRCDtRP;

/** Offset 0x021B - Reserved
**/
  UINT8                       Reserved10;

/** Offset 0x021C - tREFI
  Refresh Interval, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT16                      tREFI;

/** Offset 0x021E - tRFC
  Min Refresh Recovery Delay Time, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT16                      tRFC;

/** Offset 0x0220 - tRRD
  Min Row Active to Row Active Delay Time, 0: AUTO, max: 255. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT8                       tRRD;

/** Offset 0x0221 - tRTP
  Min Internal Read to Precharge Command Delay Time, 0: AUTO, max: 255. Only used
  if FspmUpd->FspmConfig.SpdProfileSelected == 1 (Custom Profile).
**/
  UINT8                       tRTP;

/** Offset 0x0222 - tWR
  Min Write Recovery Time, 0: AUTO, legal values: 5, 6, 7, 8, 10, 12, 14, 16, 18,
  20, 24, 30, 34, 40. Only used if FspmUpd->FspmConfig.SpdProfileSelected == 1 (Custom Profile).
  0:Auto, 5:5, 6:6, 7:7, 8:8, 10:10, 12:12, 14:14, 16:16, 18:18, 20:20, 24:24, 30:30,
  34:34, 40:40
**/
  UINT8                       tWR;

/** Offset 0x0223 - tWTR
  Min Internal Write to Read Command Delay Time, 0: AUTO, max: 255. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT8                       tWTR;

/** Offset 0x0224 - Reserved
**/
  UINT8                      Reserved11[12];

/** Offset 0x0230 - NMode
  System command rate, range 0-2, 0 means auto, 1 = 1N, 2 = 2N
**/
  UINT8                       NModeSupport;

/** Offset 0x0231 - Enable Intel HD Audio (Azalia)
  0: Disable, 1: Enable (Default) Azalia controller
  $EN_DIS
**/
  UINT8                       PchHdaEnable;

/** Offset 0x0232 - Enable PCH ISH Controller
  0: Disable, 1: Enable (Default) ISH Controller
  $EN_DIS
**/
  UINT8                       PchIshEnable;

/** Offset 0x0233 - Reserved
**/
  UINT8                       Reserved12[7];

/** Offset 0x023A - SAGV Gear Ratio
  Gear Selection for SAGV points. 0 - Auto, 2-Gear 2, 4-Gear 4
**/
  UINT8                       SaGvGear[4];

/** Offset 0x023E - SAGV Frequency
  SAGV Frequency per point in Mhz. 0 for Auto and a ratio of 133/100MHz: 1333/1300.
**/
  UINT16                      SaGvFreq[4];

/** Offset 0x0246 - SAGV Disabled Gear Ratio
  Gear Selection for SAGV Disabled. 0 - Auto, 2-Gear 2, 2-Gear 4
**/
  UINT8                       GearRatio;

/** Offset 0x0247 - Reserved
**/
  UINT8                       Reserved13[69];

/** Offset 0x028C - MMIO size adjustment for AUTO mode
  Positive number means increasing MMIO size, Negative value means decreasing MMIO
  size: 0 (Default)=no change to AUTO mode MMIO size
**/
  UINT16                      MmioSizeAdjustment;

/** Offset 0x028E - Selection of the primary display device
  0=iGFX, 3(Default)=AUTO, 4=Hybrid Graphics
  0:iGFX, 3:AUTO, 4:Hybrid Graphics
**/
  UINT8                       PrimaryDisplay;

/** Offset 0x028F - Reserved
**/
  UINT8                       Reserved14;

/** Offset 0x0290 - Temporary MMIO address for GMADR
  Obsolete field now and it has been extended to 64 bit address, used LMemBar
**/
  UINT32                      GmAdr;

/** Offset 0x0294 - Temporary MMIO address for GTTMMADR
  The reference code will use this as Temporary MMIO address space to access GTTMMADR
  Registers.Platform should provide conflict free Temporary MMIO Range: GttMmAdr
  to (GttMmAdr + 2MB MMIO + 6MB Reserved + GttSize). Default is (GmAdr - (2MB MMIO
  + 6MB Reserved + GttSize)) to (GmAdr - 0x1) (Where GttSize = 8MB)
**/
  UINT32                      GttMmAdr;

/** Offset 0x0298 - Enable/Disable MRC TXT dependency
  When enabled MRC execution will wait for TXT initialization to be done first. Disabled(0x0)(Default):
  MRC will not wait for TXT initialization, Enabled(0x1): MRC will wait for TXT initialization
  $EN_DIS
**/
  UINT8                       TxtImplemented;

/** Offset 0x0299 - Enable/Disable SA OcSupport
  Enable: Enable SA OcSupport, Disable(Default): Disable SA OcSupport
  $EN_DIS
**/
  UINT8                       SaOcSupport;

/** Offset 0x029A - GT slice Voltage Mode
  0(Default): Adaptive, 1: Override
  0: Adaptive, 1: Override
**/
  UINT8                       GtVoltageMode;

/** Offset 0x029B - Maximum GTs turbo ratio override
  0(Default)=Minimal/Auto, 60=Maximum
**/
  UINT8                       GtMaxOcRatio;

/** Offset 0x029C - The voltage offset applied to GT slice
  0(Default)=Minimal, 1000=Maximum
**/
  UINT16                      GtVoltageOffset;

/** Offset 0x029E - The GT slice voltage override which is applied to the entire range of GT frequencies
  0(Default)=Minimal, 2000=Maximum
**/
  UINT16                      GtVoltageOverride;

/** Offset 0x02A0 - adaptive voltage applied during turbo frequencies
  0(Default)=Minimal, 2000=Maximum
**/
  UINT16                      GtAdaptiveVoltage;

/** Offset 0x02A2 - voltage offset applied to the SA
  0(Default)=Minimal, 1000=Maximum
**/
  UINT16                      SaVoltageOffset;

/** Offset 0x02A4 - PCIe root port Function number for Hybrid Graphics dGPU
  Root port Index number to indicate which PCIe root port has dGPU
**/
  UINT8                       RootPortIndex;

/** Offset 0x02A5 - Realtime Memory Timing
  0(Default): Disabled, 1: Enabled. When enabled, it will allow the system to perform
  realtime memory timing changes after MRC_DONE.
  0: Disabled, 1: Enabled
**/
  UINT8                       RealtimeMemoryTiming;

/** Offset 0x02A6 - Reserved
**/
  UINT8                       Reserved15;

/** Offset 0x02A7 - Enable/Disable SA IPU
  Enable(Default): Enable SA IPU, Disable: Disable SA IPU
  $EN_DIS
**/
  UINT8                       SaIpuEnable;

/** Offset 0x02A8 - IMGU CLKOUT Configuration
  The configuration of IMGU CLKOUT, 0: Disable;<b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       ImguClkOutEn[6];

/** Offset 0x02AE - Program GPIOs for LFP on DDI port-A device
  0=Disabled,1(Default)=eDP, 2=MIPI DSI
  0:Disabled, 1:eDP, 2:MIPI DSI
**/
  UINT8                       DdiPortAConfig;

/** Offset 0x02AF - Program GPIOs for LFP on DDI port-B device
  0(Default)=Disabled,1=eDP, 2=MIPI DSI
  0:Disabled, 1:eDP, 2:MIPI DSI
**/
  UINT8                       DdiPortBConfig;

/** Offset 0x02B0 - Enable or disable HPD of DDI port A
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPortAHpd;

/** Offset 0x02B1 - Enable or disable HPD of DDI port B
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortBHpd;

/** Offset 0x02B2 - Enable or disable HPD of DDI port C
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPortCHpd;

/** Offset 0x02B3 - Enable or disable HPD of DDI port 1
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPort1Hpd;

/** Offset 0x02B4 - Enable or disable HPD of DDI port 2
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort2Hpd;

/** Offset 0x02B5 - Enable or disable HPD of DDI port 3
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort3Hpd;

/** Offset 0x02B6 - Enable or disable HPD of DDI port 4
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort4Hpd;

/** Offset 0x02B7 - Enable or disable DDC of DDI port A
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPortADdc;

/** Offset 0x02B8 - Enable or disable DDC of DDI port B
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortBDdc;

/** Offset 0x02B9 - Enable or disable DDC of DDI port C
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPortCDdc;

/** Offset 0x02BA - Enable DDC setting of DDI Port 1
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort1Ddc;

/** Offset 0x02BB - Enable DDC setting of DDI Port 2
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort2Ddc;

/** Offset 0x02BC - Enable DDC setting of DDI Port 3
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort3Ddc;

/** Offset 0x02BD - Enable DDC setting of DDI Port 4
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort4Ddc;

/** Offset 0x02BE - Reserved
**/
  UINT8                       Reserved16[18];

/** Offset 0x02D0 - Per-core HT Disable
  Defines the per-core HT disable mask where: 1 - Disable selected logical core HT,
  0 - is ignored. Input is in HEX and each bit maps to a logical core. Ex. A value
  of '1F' would disable HT for cores 4,3,2,1 and 0. Default is 0, all cores have
  HT enabled. Range is 0 - 0x7F for max 8 cores. You can only disable up to MAX_CORE_COUNT - 1.
**/
  UINT16                      PerCoreHtDisable;

/** Offset 0x02D2 - Reserved
**/
  UINT8                       Reserved17[6];

/** Offset 0x02D8 - Thermal Velocity Boost Ratio clipping
  0: Disabled, 1(Default): Enabled. This service controls Core frequency reduction
  caused by high package temperatures for processors that implement the Intel Thermal
  Velocity Boost (TVB) feature
  $EN_DIS
**/
  UINT8                       TvbRatioClipping;

/** Offset 0x02D9 - Thermal Velocity Boost voltage optimization
  0: Disabled, 1: Enabled(Default). This service controls thermal based voltage optimizations
  for processors that implement the Intel Thermal Velocity Boost (TVB) feature.
  $EN_DIS
**/
  UINT8                       TvbVoltageOptimization;

/** Offset 0x02DA - Reserved
**/
  UINT8                       Reserved18[45];

/** Offset 0x0307 - DMI Max Link Speed
  Auto (Default)(0x0): Maximum possible link speed, Gen1(0x1): Limit Link to Gen1
  Speed, Gen2(0x2): Limit Link to Gen2 Speed, Gen3(0x3):Limit Link to Gen3 Speed
  0:Auto, 1:Gen1, 2:Gen2, 3:Gen3
**/
  UINT8                       DmiMaxLinkSpeed;

/** Offset 0x0308 - PCH DMI Equalization Phase 2
  DMI Equalization Phase 2. (0x0): Disable phase 2, (0x1): Enable phase 2, (0x2)(Default):
  AUTO - Use the current default method
  0:Disable phase2, 1:Enable phase2, 2:Auto
**/
  UINT8                       PchDmiGen3EqPh2Enable;

/** Offset 0x0309 - PCH DMI Gen3 Equalization Phase3
  DMI Gen3 Equalization Phase3. Auto(0x0)(Default): Use the current default method,
  HwEq(0x1): Use Adaptive Hardware Equalization, SwEq(0x2): Use Adaptive Software
  Equalization (Implemented in BIOS Reference Code), Static(0x3): Use the Static
  EQs provided in DmiGen3EndPointPreset array for Phase1 AND Phase3 (Instead of just
  Phase1), Disabled(0x4): Bypass Equalization Phase 3
  0:Auto, 1:HwEq, 2:SwEq, 3:StaticEq, 4:BypassPhase3
**/
  UINT8                       PchDmiGen3EqPh3Method;

/** Offset 0x030A - Enable/Disable DMI GEN3 Static EQ Phase1 programming
  Program DMI Gen3 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static
  Presets Programming, Enabled(0x1)(Default): Enable  EQ Phase1 Static Presets Programming
  $EN_DIS
**/
  UINT8                       DmiGen3ProgramStaticEq;

/** Offset 0x030B - PCH DMI Gen3 Root port preset values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-9, 4 is default for each lane
**/
  UINT8                       PchDmiGen3RootPortPreset[8];

/** Offset 0x0313 - PCH DMI Gen3 End port preset values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-9, 7 is default for each lane
**/
  UINT8                       PchDmiGen3EndPointPreset[8];

/** Offset 0x031B - PCH DMI Gen3 End port Hint values per lane
  Used for programming DMI Gen3 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
  UINT8                       PchDmiGen3EndPointHint[8];

/** Offset 0x0323 - DMI ASPM Configuration:{Combo
  Set ASPM Configuration
  0:Disabled, 1:L0s, 2:L1, 3:L1L0s
**/
  UINT8                       DmiAspm;

/** Offset 0x0324 - Reserved
**/
  UINT8                       Reserved19;

/** Offset 0x0325 - Enable/Disable DMI GEN3 Hardware Eq
  Enable/Disable DMI GEN3 Hardware Eq. Disabled(0x0): Disable Hardware Eq, Enabled(0x1)(Default):
  Enable  EQ Phase1 Static Presets Programming
  $EN_DIS
**/
  UINT8                       DmiHweq;

/** Offset 0x0326 - Enable/Disable DMI GEN3 Phase 23 Bypass
  DMIGEN3 Phase 23 Bypass. Disabled(0x0)(Default): Disable Phase 23 Bypass, Enabled(0x1):
  Enable  Phase 23 Bypass
  $EN_DIS
**/
  UINT8                       Gen3EqPhase23Bypass;

/** Offset 0x0327 - Enable/Disable DMI GEN3 Phase 3 Bypass
  DMIGEN3 Phase 3 Bypass. Disabled(0x0)(Default): Disable Phase 3 Bypass, Enabled(0x1):
  Enable  Phase 3 Bypass
  $EN_DIS
**/
  UINT8                       Gen3EqPhase3Bypass;

/** Offset 0x0328 - Enable/Disable DMI Gen3 EQ Local Transmitter Coefficient Override Enable
  Program Gen3 EQ Local Transmitter Coefficient Override. Disabled(0x0): Disable Local
  Transmitter Coefficient Override, Enabled(0x1)(Default): Enable  Local Transmitter
  Coefficient Override
  $EN_DIS
**/
  UINT8                       Gen3LtcoEnable;

/** Offset 0x0329 - Enable/Disable DMI Gen3 EQ Remote Transmitter Coefficient/Preset Override Enable
  Program Remote Transmitter Coefficient/Preset Override. Disabled(0x0)(Default):
  Disable Remote Transmitter Coefficient/Preset Override, Enabled(0x1): Enable  Remote
  Transmitter Coefficient/Preset Override
  $EN_DIS
**/
  UINT8                       Gen3RtcoRtpoEnable;

/** Offset 0x032A - DMI Gen3 Transmitter Pre-Cursor Coefficient
  Used for programming DMI Gen3 Transmitter Pre-Cursor Coefficient . Range: 0-10,
  2 is default for each lane
**/
  UINT8                       DmiGen3Ltcpre[8];

/** Offset 0x0332 - DMI Gen3 Transmitter Post-Cursor Coefficient
  Used for programming Transmitter Post-Cursor Coefficient. Range: 0-9, 2 is default
  for each lane
**/
  UINT8                       DmiGen3Ltcpo[8];

/** Offset 0x033A - Reserved
**/
  UINT8                       Reserved20[34];

/** Offset 0x035C - Enable/Disable DMI GEN3 DmiGen3DsPresetEnable
  Enable/Disable DMI GEN3 DmiGen3DsPreset. Auto(0x0)(Default): DmiGen3DsPresetEnable,
  Manual(0x1): Enable DmiGen3DsPresetEnable
  $EN_DIS
**/
  UINT8                       DmiGen3DsPresetEnable;

/** Offset 0x035D - DMI Gen3 Root port preset Rx values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-10, 1 is default
  for each lane
**/
  UINT8                       DmiGen3DsPortRxPreset[8];

/** Offset 0x0365 - DMI Gen3 Root port preset Tx values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-10, 7 is default
  for each lane
**/
  UINT8                       DmiGen3DsPortTxPreset[8];

/** Offset 0x036D - Enable/Disable DMI GEN3 DmiGen3UsPresetEnable
  Enable/Disable DMI GEN3 DmiGen3UsPreset. Auto(0x0)(Default): DmiGen3UsPresetEnable,
  Manual(0x1): Enable DmiGen3UsPresetEnable
  $EN_DIS
**/
  UINT8                       DmiGen3UsPresetEnable;

/** Offset 0x036E - DMI Gen3 Root port preset Rx values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-10, 7 is default
  for each lane
**/
  UINT8                       DmiGen3UsPortRxPreset[8];

/** Offset 0x0376 - DMI Gen3 Root port preset Tx values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-10, 1 is default
  for each lane
**/
  UINT8                       DmiGen3UsPortTxPreset[8];

/** Offset 0x037E - Reserved
**/
  UINT8                       Reserved21[54];

/** Offset 0x03B4 - DMI ASPM L1 exit Latency
  Range: 0-7, 4 is default L1 exit Latency
**/
  UINT8                       DmiAspmL1ExitLatency;

/** Offset 0x03B5 - Reserved
**/
  UINT8                       Reserved22[63];

/** Offset 0x03F4 - BIST on Reset
  Enable/Disable BIST (Built-In Self Test) on reset. <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       BistOnReset;

/** Offset 0x03F5 - Skip Stop PBET Timer Enable/Disable
  Skip Stop PBET Timer; <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       SkipStopPbet;

/** Offset 0x03F6 - Over clocking support
  Over clocking support; <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       OcSupport;

/** Offset 0x03F7 - Over clocking Lock
  Lock Overclocking. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       OcLock;

/** Offset 0x03F8 - Maximum Core Turbo Ratio Override
  Maximum core turbo ratio override allows to increase CPU core frequency beyond the
  fused max turbo ratio limit. <b>0: Hardware defaults.</b> Range: 0-85 if CoreRatioExtensionMode
  is disabled. 0-120 if CoreRatioExtensionMode is enabled.
**/
  UINT8                       CoreMaxOcRatio;

/** Offset 0x03F9 - Core voltage mode
  Core voltage mode; <b>0: Adaptive</b>; 1: Override.
  $EN_DIS
**/
  UINT8                       CoreVoltageMode;

/** Offset 0x03FA - Maximum clr turbo ratio override
  Maximum clr turbo ratio override allows to increase CPU clr frequency beyond the
  fused max turbo ratio limit. <b>0: Hardware defaults.</b>  Range: 0-85
**/
  UINT8                       RingMaxOcRatio;

/** Offset 0x03FB - Hyper Threading Enable/Disable
  Enable or Disable Hyper-Threading Technology. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       HyperThreading;

/** Offset 0x03FC - Enable or Disable CPU Ratio Override
  Enable/Disable CPU Flex Ratio Programming; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       CpuRatioOverride;

/** Offset 0x03FD - CPU ratio value
  This value must be between Max Efficiency Ratio (LFM) and Maximum non-turbo ratio
  set by Hardware (HFM). Valid Range 0 to 63.
**/
  UINT8                       CpuRatio;

/** Offset 0x03FE - Reserved
**/
  UINT8                       Reserved23;

/** Offset 0x03FF - Number of active big cores
  Number of P-cores to enable in each processor package. Note: Number of P-Cores and
  E-Cores are looked at together. When both are {0,0
  0:Disable all big cores, 1:1, 2:2, 3:3, 0xFF:Active all big cores
**/
  UINT8                       ActiveCoreCount;

/** Offset 0x0400 - Processor Early Power On Configuration FCLK setting
  FCLK frequency can take values of 400MHz, 800MHz and 1GHz. <b>0: 800 MHz (ULT/ULX)</b>.
  <b>1: 1 GHz (DT/Halo)</b>. Not supported on ULT/ULX.- 2: 400 MHz. - 3: Reserved
  0:800 MHz, 1: 1 GHz, 2: 400 MHz, 3: Reserved
**/
  UINT8                       FClkFrequency;

/** Offset 0x0401 - Enable or Disable VMX
  Enable or Disable VMX, When enabled, a VMM can utilize the additional hardware capabilities
  provided by Vanderpool Technology. 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       VmxEnable;

/** Offset 0x0402 - AVX2 Ratio Offset
  0(Default)= No Offset. Range 0 - 31. Specifies number of bins to decrease AVX ratio
  vs. Core Ratio. Uses Mailbox MSR 0x150, cmd 0x1B.
**/
  UINT8                       Avx2RatioOffset;

/** Offset 0x0403 - AVX3 Ratio Offset
  DEPRECATED. 0(Default)= No Offset. Range 0 - 31. Specifies number of bins to decrease
  AVX ratio vs. Core Ratio. Uses Mailbox MSR 0x150, cmd 0x1B.
**/
  UINT8                       Avx3RatioOffset;

/** Offset 0x0404 - BCLK Adaptive Voltage Enable
  When enabled, the CPU V/F curves are aware of BCLK frequency when calculated. </b>0:
  Disable;<b> 1: Enable
  $EN_DIS
**/
  UINT8                       BclkAdaptiveVoltage;

/** Offset 0x0405 - Reserved
**/
  UINT8                       Reserved24;

/** Offset 0x0406 - core voltage override
  The core voltage override which is applied to the entire range of cpu core frequencies.
  Valid Range 0 to 2000
**/
  UINT16                      CoreVoltageOverride;

/** Offset 0x0408 - Core Turbo Adaptive Voltage
  Adaptive voltage applied to the cpu core when the cpu is operating in turbo mode.
  Valid Range 0 to 2000
**/
  UINT16                      CoreAdaptiveVoltage;

/** Offset 0x040A - Core Turbo voltage Offset
  The voltage offset applied to the core while operating in turbo mode.Valid Range 0 to 1000
**/
  UINT16                      CoreVoltageOffset;

/** Offset 0x040C - Core PLL voltage offset
  Core PLL voltage offset. <b>0: No offset</b>. Range 0-15
**/
  UINT8                       CorePllVoltageOffset;

/** Offset 0x040D - Ring Downbin
  Ring Downbin enable/disable. When enabled, CPU will ensure the ring ratio is always
  lower than the core ratio.0: Disable; <b>1: Enable.</b>
  $EN_DIS
**/
  UINT8                       RingDownBin;

/** Offset 0x040E - Ring voltage mode
  Ring voltage mode; <b>0: Adaptive</b>; 1: Override.
  $EN_DIS
**/
  UINT8                       RingVoltageMode;

/** Offset 0x040F - TjMax Offset
  TjMax offset.Specified value here is clipped by pCode (125 - TjMax Offset) to support
  TjMax in the range of 62 to 115 deg Celsius. Valid Range 10 - 63
**/
  UINT8                       TjMaxOffset;

/** Offset 0x0410 - Ring voltage override
  The ring voltage override which is applied to the entire range of cpu ring frequencies.
  Valid Range 0 to 2000
**/
  UINT16                      RingVoltageOverride;

/** Offset 0x0412 - Ring Turbo Adaptive Voltage
  Adaptive voltage applied to the cpu ring when the cpu is operating in turbo mode.
  Valid Range 0 to 2000
**/
  UINT16                      RingAdaptiveVoltage;

/** Offset 0x0414 - Ring Turbo voltage Offset
  The voltage offset applied to the ring while operating in turbo mode. Valid Range 0 to 1000
**/
  UINT16                      RingVoltageOffset;

/** Offset 0x0416 - Enable or Disable TME
  Configure Total Memory Encryption (TME) to protect DRAM data from physical attacks.
  <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       TmeEnable;

/** Offset 0x0417 - Enable CPU CrashLog
  Enable or Disable CPU CrashLog; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       CpuCrashLogEnable;

/** Offset 0x0418 - CPU Run Control
  Enable, Disable or Do not configure CPU Run Control; 0: Disable; 1: Enable ; <b>2:
  No Change</b>
  0:Disabled, 1:Enabled, 2:No Change
**/
  UINT8                       DebugInterfaceEnable;

/** Offset 0x0419 - CPU Run Control Lock
  Lock or Unlock CPU Run Control; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       DebugInterfaceLockEnable;

/** Offset 0x041A - Reserved
**/
  UINT8                       Reserved25[67];

/** Offset 0x045D - Core VF Point Offset Mode
  Selects Core Voltage & Frequency Offset mode between Legacy and Selection modes.
  In Legacy Mode, setting a global offset for the entire VF curve. In Selection Mode,
  setting a selected VF point; <b>0: Legacy</b>; 1: Selection.
  0:Legacy, 1:Selection
**/
  UINT8                       CoreVfPointOffsetMode;

/** Offset 0x045E - Core VF Point Offset
  Array used to specifies the Core Voltage Offset applied to the each selected VF
  Point. This voltage is specified in millivolts.
**/
  UINT16                      CoreVfPointOffset[15];

/** Offset 0x047C - Core VF Point Offset Prefix
  Sets the CoreVfPointOffset value as positive or negative for corresponding core
  VF Point; <b>0: Positive </b>; 1: Negative.
  0:Positive, 1:Negative
**/
  UINT8                       CoreVfPointOffsetPrefix[15];

/** Offset 0x048B - Core VF Point Ratio
  Array for the each selected Core VF Point to display the ration.
**/
  UINT8                       CoreVfPointRatio[15];

/** Offset 0x049A - Core VF Point Count
  Number of supported Core Voltage & Frequency Point Offset
**/
  UINT8                       CoreVfPointCount;

/** Offset 0x049B - Reserved
**/
  UINT8                       Reserved26[25];

/** Offset 0x04B4 - Per Core Max Ratio override
  Enable or disable Per Core PState OC supported by writing OCMB 0x1D to program new
  favored core ratio to each Core. <b>0: Disable</b>, 1: enable
  $EN_DIS
**/
  UINT8                       PerCoreRatioOverride;

/** Offset 0x04B5 - Reserved
**/
  UINT8                       Reserved27[41];

/** Offset 0x04DE - Per Core Current Max Ratio
  Array for the Per Core Max Ratio
**/
  UINT8                       PerCoreRatio[8];

/** Offset 0x04E6 - Reserved
**/
  UINT8                       Reserved28[54];

/** Offset 0x051C - Margin Limit Check
  Margin Limit Check. Choose level of margin check
  0:Disable, 1:L1, 2:L2, 3:Both
**/
  UINT8                       MarginLimitCheck;

/** Offset 0x051D - Reserved
**/
  UINT8                       Reserved29[14];

/** Offset 0x052B - Pvd Ratio Threshold for SOC/CPU die
  Array of Pvd Ratio Threshold for SOC/CPU die is the threshold value for input ratio
  (P0 to Pn) to select the multiplier so that the output is within the DCO frequency
  range. As per the die selected, this threshold is applied to SA and MC/CMI PLL
  for SOC die and SA, Ring and Atom PLL for CPU die. Range 0-63. When the threshold
  is 0, static PVD ratio is selected based on the PVD Mode for SOC. <b>0: Default</b>.
**/
  UINT8                       PvdRatioThreshold[2];

/** Offset 0x052D - Reserved
**/
  UINT8                       Reserved30[68];

/** Offset 0x0571 - GPIO Override
  Gpio Override Level - FSP will not configure any GPIOs and rely on GPIO setings
  before moved to FSP. Available configurations 0: Disable; 1: Level 1 - Skips GPIO
  configuration in PEI/FSPM/FSPT phase;2: Level 2 - Reserved for use
**/
  UINT8                       GpioOverride;

/** Offset 0x0572 - Reserved
**/
  UINT8                       Reserved31[10];

/** Offset 0x057C - CPU BCLK OC Frequency
  CPU BCLK OC Frequency in KHz units. 98000000Hz = 98MHz <b>0 - Auto</b>. Range is
  40Mhz-1000Mhz.
**/
  UINT32                      CpuBclkOcFrequency;

/** Offset 0x0580 - Reserved
**/
  UINT8                      Reserved32[4];

/** Offset 0x0584 - Enable CPU CrashLog GPRs dump
  Enable or Disable CPU CrashLog GPRs dump; <b>0: Disable</b>; 1: Enable; 2: Only
  disable Smm GPRs dump
  0:Disabled, 1:Enabled, 2:Only Smm GPRs Disabled
**/
  UINT8                       CrashLogGprs;

/** Offset 0x0585 - Reserved
**/
  UINT8                       Reserved33[142];

/** Offset 0x0613 - Acoustic Noise Mitigation feature
  Enabling this option will help mitigate acoustic noise on certain SKUs when the
  CPU is in deeper C state. <b>0: Disabled</b>; 1: Enabled
  $EN_DIS
**/
  UINT8                       AcousticNoiseMitigation;

/** Offset 0x0614 - Reserved
**/
  UINT8                       Reserved34[2];

/** Offset 0x0616 - Platform Power Pmax
  PSYS PMax power, defined in 1/8 Watt increments. <b>0 - Auto</b> Specified in 1/8
  Watt increments. Range 0-1024 Watts(0-8191). Value of 800 = 100W
**/
  UINT16                      PsysPmax;

/** Offset 0x0618 - Reserved
**/
  UINT8                      Reserved35[12];

/** Offset 0x0624 - AcLoadline
  AC Loadline defined in 1/100 mOhms. A value of 100 = 1.00 mOhm, and 1255 = 12.55
  mOhm. Range is 0-6249 (0-62.49 mOhms). 0 = AUTO/HW default. [0] for IA, [1] for
  GT, [2] for SA, [3] through [5] are Reserved.
**/
  UINT16                      AcLoadline[6];

/** Offset 0x0630 - DcLoadline
  DC Loadline defined in 1/100 mOhms. A value of 100 = 1.00 mOhm, and 1255 = 12.55
  mOhm. Range is 0-6249 (0-62.49 mOhms). 0 = AUTO/HW default. [0] for IA, [1] for
  GT, [2] for SA, [3] through [5] are Reserved.
**/
  UINT16                      DcLoadline[6];

/** Offset 0x063C - Power State 1 Threshold current
  PS Current Threshold1, defined in 1/4 A increments. A value of 400 = 100A. Range
  0-512, which translates to 0-128A. 0 = AUTO. [0] for IA, [1] for GT, [2] for SA,
  [3] through [5] are Reserved.
**/
  UINT16                      Psi1Threshold[6];

/** Offset 0x0648 - Power State 2 Threshold current
  PS Current Threshold2, defined in 1/4 A increments. A value of 400 = 100A. Range
  0-512, which translates to 0-128A. 0 = AUTO. [0] for IA, [1] for GT, [2] for SA,
  [3] through [5] are Reserved.
**/
  UINT16                      Psi2Threshold[6];

/** Offset 0x0654 - Power State 3 Threshold current
  PS Current Threshold3, defined in 1/4 A increments. A value of 400 = 100A. Range
  0-512, which translates to 0-128A. 0 = AUTO. [0] for IA, [1] for GT, [2] for SA,
  [3] through [5] are Reserved.
**/
  UINT16                      Psi3Threshold[6];

/** Offset 0x0660 - Reserved
**/
  UINT8                       Reserved36[54];

/** Offset 0x0696 - Thermal Design Current enable/disable
  Thermal Design Current enable/disable; <b>0: Disable</b>; 1: Enable. [0] for IA,
  [1] for GT, [2] for SA, [3] through [5] are Reserved.
**/
  UINT8                       TdcEnable[6];

/** Offset 0x069C - Thermal Design Current time window
  TDC Time Window, value of IA either in milliseconds or seconds, value of GT/SA is
  in milliseconds. 1ms is default. Range of IA from 1ms to 448s, Range of GT/SA is
  1ms to 10ms, except for 9ms. 9ms has no valid encoding in the MSR definition.
**/
  UINT32                      TdcTimeWindow[6];

/** Offset 0x06B4 - Reserved
**/
  UINT8                       Reserved37[128];

/** Offset 0x0734 - Disable Fast Slew Rate for Deep Package C States for VR domains
  This option needs to be configured to reduce acoustic noise during deeper C states.
  False: Don't disable Fast ramp during deeper C states; True: Disable Fast ramp
  during deeper C state. [0] for IA, [1] for GT, [2] for SA, [3] through [5] are
  Reserved. <b>0: False</b>; 1: True
  $EN_DIS
**/
  UINT8                       FastPkgCRampDisable[6];

/** Offset 0x073A - Slew Rate configuration for Deep Package C States for VR domains
  Set VR IA/GT/SA Slow Slew Rate for Deep Package C State ramp time; Slow slew rate
  equals to Fast divided by number, the number is 2, 4, 8, 16 to slow down the slew
  rate to help minimize acoustic noise; divide by 16 is disabled for GT/SA. <b>0:
  Fast/2</b>; 1: Fast/4; 2: Fast/8; 3: Fast/16; 0xFF: Ignore the configuration
  0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16, 0xFF: Ignore the configuration
**/
  UINT8                       SlowSlewRate[6];

/** Offset 0x0740 - Reserved
**/
  UINT8                      Reserved38[26];

/** Offset 0x075A - VR Fast Vmode ICC Limit support
  Voltage Regulator Fast Vmode ICC Limit. A value of 400 = 100A. A value of 0 corresponds
  to feature disabled (no reactive protection). This value represents the current
  threshold where the VR would initiate reactive protection if Fast Vmode is enabled.
  The value is represented in 1/4 A increments. Range 0-2040. [0] for IA, [1] for
  GT, [2] for SA, [3] through [5] are Reserved.
**/
  UINT16                      IccLimit[6];

/** Offset 0x0766 - Enable/Disable VR FastVmode. The VR will initiate reactive protection if Fast Vmode is enabled.
  Enable/Disable VR FastVmode; 0: Disable; <b>1: Enable</b>. For all VR by domain
  0: Disable, 1: Enable
**/
  UINT8                       EnableFastVmode[6];

/** Offset 0x076C - Enable CEP
  Enable/Disable CEP (Current Excursion Protection) Support. 0: Disable; <b>1: Enable</b>.
  [0] for IA, [1] for GT, [2] for SA, [3] through [5] are Reserved.
  $EN_DIS
**/
  UINT8                       CepEnable[6];

/** Offset 0x0772 - Reserved
**/
  UINT8                       Reserved39[146];

/** Offset 0x0804 - BiosGuard
  Enable/Disable. 0: Disable, Enable/Disable BIOS Guard feature, 1: enable
  $EN_DIS
**/
  UINT8                       BiosGuard;

/** Offset 0x0805
**/
  UINT8                       BiosGuardToolsInterface;

/** Offset 0x0806 - Txt
  Enables utilization of additional hardware capabilities provided by Intel (R) Trusted
  Execution Technology. Changes require a full power cycle to take effect. <b>0:
  Disable</b>, 1: Enable
  $EN_DIS
**/
  UINT8                       Txt;

/** Offset 0x0807 - Reserved
**/
  UINT8                       Reserved40;

/** Offset 0x0808 - PrmrrSize
  Enable/Disable. 0: Disable, define default value of PrmrrSize , 1: enable
**/
  UINT32                      PrmrrSize;

/** Offset 0x080C - SinitMemorySize
  Enable/Disable. 0: Disable, define default value of SinitMemorySize , 1: enable
**/
  UINT32                      SinitMemorySize;

/** Offset 0x0810 - Reserved
**/
  UINT8                       Reserved41[8];

/** Offset 0x0818 - TxtDprMemoryBase
  Enable/Disable. 0: Disable, define default value of TxtDprMemoryBase , 1: enable
**/
  UINT64                      TxtDprMemoryBase;

/** Offset 0x0820 - TxtHeapMemorySize
  Enable/Disable. 0: Disable, define default value of TxtHeapMemorySize , 1: enable
**/
  UINT32                      TxtHeapMemorySize;

/** Offset 0x0824 - TxtDprMemorySize
  Reserve DPR memory size (0-255) MB. 0: Disable, define default value of TxtDprMemorySize
  , 1: enable
**/
  UINT32                      TxtDprMemorySize;

/** Offset 0x0828 - BiosAcmBase
  Enable/Disable. 0: Disable, define default value of BiosAcmBase , 1: enable
**/
  UINT32                      BiosAcmBase;

/** Offset 0x082C - BiosAcmSize
  Enable/Disable. 0: Disable, define default value of BiosAcmSize , 1: enable
**/
  UINT32                      BiosAcmSize;

/** Offset 0x0830 - ApStartupBase
  Enable/Disable. 0: Disable, define default value of BiosAcmBase , 1: enable
**/
  UINT32                      ApStartupBase;

/** Offset 0x0834 - TgaSize
  Enable/Disable. 0: Disable, define default value of TgaSize , 1: enable
**/
  UINT32                      TgaSize;

/** Offset 0x0838 - TxtLcpPdBase
  Enable/Disable. 0: Disable, define default value of TxtLcpPdBase , 1: enable
**/
  UINT64                      TxtLcpPdBase;

/** Offset 0x0840 - TxtLcpPdSize
  Enable/Disable. 0: Disable, define default value of TxtLcpPdSize , 1: enable
**/
  UINT64                      TxtLcpPdSize;

/** Offset 0x0848 - IsTPMPresence
  IsTPMPresence default values
**/
  UINT8                       IsTPMPresence;

/** Offset 0x0849 - Reserved
**/
  UINT8                       Reserved42[32];

/** Offset 0x0869 - Enable PCH HSIO PCIE Rx Set Ctle
  Enable PCH PCIe Gen 3 Set CTLE Value.
**/
  UINT8                       PchPcieHsioRxSetCtleEnable[28];

/** Offset 0x0885 - PCH HSIO PCIE Rx Set Ctle Value
  PCH PCIe Gen 3 Set CTLE Value.
**/
  UINT8                       PchPcieHsioRxSetCtle[28];

/** Offset 0x08A1 - Enble PCH HSIO PCIE TX Gen 1 Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen1DownscaleAmpEnable[28];

/** Offset 0x08BD - PCH HSIO PCIE Gen 2 TX Output Downscale Amplitude Adjustment value
  PCH PCIe Gen 2 TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchPcieHsioTxGen1DownscaleAmp[28];

/** Offset 0x08D9 - Enable PCH HSIO PCIE TX Gen 2 Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen2DownscaleAmpEnable[28];

/** Offset 0x08F5 - PCH HSIO PCIE Gen 2 TX Output Downscale Amplitude Adjustment value
  PCH PCIe Gen 2 TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchPcieHsioTxGen2DownscaleAmp[28];

/** Offset 0x0911 - Enable PCH HSIO PCIE TX Gen 3 Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen3DownscaleAmpEnable[28];

/** Offset 0x092D - PCH HSIO PCIE Gen 3 TX Output Downscale Amplitude Adjustment value
  PCH PCIe Gen 3 TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchPcieHsioTxGen3DownscaleAmp[28];

/** Offset 0x0949 - Enable PCH HSIO PCIE Gen 1 TX Output De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen1DeEmphEnable[28];

/** Offset 0x0965 - PCH HSIO PCIE Gen 1 TX Output De-Emphasis Adjustment value
  PCH PCIe Gen 1 TX Output De-Emphasis Adjustment Setting.
**/
  UINT8                       PchPcieHsioTxGen1DeEmph[28];

/** Offset 0x0981 - Enable PCH HSIO PCIE Gen 2 TX Output -3.5dB De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen2DeEmph3p5Enable[28];

/** Offset 0x099D - PCH HSIO PCIE Gen 2 TX Output -3.5dB De-Emphasis Adjustment value
  PCH PCIe Gen 2 TX Output -3.5dB De-Emphasis Adjustment Setting.
**/
  UINT8                       PchPcieHsioTxGen2DeEmph3p5[28];

/** Offset 0x09B9 - Enable PCH HSIO PCIE Gen 2 TX Output -6.0dB De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen2DeEmph6p0Enable[28];

/** Offset 0x09D5 - PCH HSIO PCIE Gen 2 TX Output -6.0dB De-Emphasis Adjustment value
  PCH PCIe Gen 2 TX Output -6.0dB De-Emphasis Adjustment Setting.
**/
  UINT8                       PchPcieHsioTxGen2DeEmph6p0[28];

/** Offset 0x09F1 - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioRxGen1EqBoostMagEnable[8];

/** Offset 0x09F9 - PCH HSIO SATA 1.5 Gb/s Receiver Equalization Boost Magnitude Adjustment value
  PCH HSIO SATA 1.5 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
  UINT8                       PchSataHsioRxGen1EqBoostMag[8];

/** Offset 0x0A01 - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioRxGen2EqBoostMagEnable[8];

/** Offset 0x0A09 - PCH HSIO SATA 3.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value
  PCH HSIO SATA 3.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
  UINT8                       PchSataHsioRxGen2EqBoostMag[8];

/** Offset 0x0A11 - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioRxGen3EqBoostMagEnable[8];

/** Offset 0x0A19 - PCH HSIO SATA 6.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value
  PCH HSIO SATA 6.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
  UINT8                       PchSataHsioRxGen3EqBoostMag[8];

/** Offset 0x0A21 - Enable PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen1DownscaleAmpEnable[8];

/** Offset 0x0A29 - PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value
  PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchSataHsioTxGen1DownscaleAmp[8];

/** Offset 0x0A31 - Enable PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen2DownscaleAmpEnable[8];

/** Offset 0x0A39 - PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value
  PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchSataHsioTxGen2DownscaleAmp[8];

/** Offset 0x0A41 - Enable PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen3DownscaleAmpEnable[8];

/** Offset 0x0A49 - PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value
  PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchSataHsioTxGen3DownscaleAmp[8];

/** Offset 0x0A51 - Enable PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen1DeEmphEnable[8];

/** Offset 0x0A59 - PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting
  PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
  UINT8                       PchSataHsioTxGen1DeEmph[8];

/** Offset 0x0A61 - Enable PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen2DeEmphEnable[8];

/** Offset 0x0A69 - PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting
  PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
  UINT8                       PchSataHsioTxGen2DeEmph[8];

/** Offset 0x0A71 - Enable PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen3DeEmphEnable[8];

/** Offset 0x0A79 - PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting
  PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
  UINT8                       PchSataHsioTxGen3DeEmph[8];

/** Offset 0x0A81 - PCH LPC Enhance the port 8xh decoding
  Original LPC only decodes one byte of port 80h.
  $EN_DIS
**/
  UINT8                       PchLpcEnhancePort8xhDecoding;

/** Offset 0x0A82 - PCH Port80 Route
  Control where the Port 80h cycles are sent, 0: LPC; 1: PCI.
  $EN_DIS
**/
  UINT8                       PchPort80Route;

/** Offset 0x0A83 - Enable SMBus ARP support
  Enable SMBus ARP support.
  $EN_DIS
**/
  UINT8                       SmbusArpEnable;

/** Offset 0x0A84 - Number of RsvdSmbusAddressTable.
  The number of elements in the RsvdSmbusAddressTable.
**/
  UINT8                       PchNumRsvdSmbusAddresses;

/** Offset 0x0A85 - Reserved
**/
  UINT8                       Reserved43;

/** Offset 0x0A86 - SMBUS Base Address
  SMBUS Base Address (IO space).
**/
  UINT16                      PchSmbusIoBase;

/** Offset 0x0A88 - Enable SMBus Alert Pin
  Enable SMBus Alert Pin.
  $EN_DIS
**/
  UINT8                       PchSmbAlertEnable;

/** Offset 0x0A89 - Usage type for SOC/IOE ClkSrc
  0-23: PCIe rootport, 0x70:LAN, 0x80: unspecified but in use (free running), 0xFF: not used
**/
  UINT8                       PcieClkSrcUsage[16];

/** Offset 0x0A99 - Reserved
**/
  UINT8                       Reserved44[16];

/** Offset 0x0AA9 - SOC/IOE ClkReq-to-ClkSrc mapping
  Number of ClkReq signal assigned to ClkSrc
**/
  UINT8                       PcieClkSrcClkReq[16];

/** Offset 0x0AB9 - Reserved
**/
  UINT8                       Reserved45[55];

/** Offset 0x0AF0 - Enable PCH PCIE RP Mask
  Enable/disable PCH PCIE Root Ports. 0: disable, 1: enable. One bit for each port,
  bit0 for port1, bit1 for port2, and so on.
**/
  UINT32                      PchPcieRpEnableMask;

/** Offset 0x0AF4 - Enable SOC/IOE PCIE RP Mask
  Enable/disable SOC/IOE PCIE Root Ports. 0: disable, 1: enable. One bit for each
  port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT16                      PcieRpEnableMask;

/** Offset 0x0AF6 - VC Type
  Virtual Channel Type Select: 0: VC0, 1: VC1.
  0: VC0, 1: VC1
**/
  UINT8                       PchHdaVcType;

/** Offset 0x0AF7 - Universal Audio Architecture compliance for DSP enabled system
  0: Not-UAA Compliant (Intel SST driver supported only), 1: UAA Compliant (HDA Inbox
  driver or SST driver supported).
  $EN_DIS
**/
  UINT8                       PchHdaDspUaaCompliance;

/** Offset 0x0AF8 - Enable HD Audio Link
  Enable/disable HD Audio Link. Muxed with SSP0/SSP1/SNDW1.
  $EN_DIS
**/
  UINT8                       PchHdaAudioLinkHdaEnable;

/** Offset 0x0AF9 - Enable HDA SDI lanes
  Enable/disable HDA SDI lanes.
**/
  UINT8                       PchHdaSdiEnable[2];

/** Offset 0x0AFB - HDA Power/Clock Gating (PGD/CGD)
  Enable/Disable HD Audio Power and Clock Gating(POR: Enable). 0: PLATFORM_POR, 1:
  FORCE_ENABLE, 2: FORCE_DISABLE.
  0: POR, 1: Force Enable, 2: Force Disable
**/
  UINT8                       PchHdaTestPowerClockGating;

/** Offset 0x0AFC - Enable HD Audio DMIC_N Link
  Enable/disable HD Audio DMIC1 link. Muxed with SNDW3.
**/
  UINT8                       PchHdaAudioLinkDmicEnable[2];

/** Offset 0x0AFE - Reserved
**/
  UINT8                       Reserved46[2];

/** Offset 0x0B00 - DMIC<N> ClkA Pin Muxing (N - DMIC number)
  Determines DMIC<N> ClkA Pin muxing. See  GPIO_*_MUXING_DMIC<N>_CLKA_*
**/
  UINT32                      PchHdaAudioLinkDmicClkAPinMux[2];

/** Offset 0x0B08 - DMIC<N> ClkB Pin Muxing
  Determines DMIC<N> ClkA Pin muxing. See GPIO_*_MUXING_DMIC<N>_CLKB_*
**/
  UINT32                      PchHdaAudioLinkDmicClkBPinMux[2];

/** Offset 0x0B10 - Enable HD Audio DSP
  Enable/disable HD Audio DSP feature.
  $EN_DIS
**/
  UINT8                       PchHdaDspEnable;

/** Offset 0x0B11 - Reserved
**/
  UINT8                       Reserved47[3];

/** Offset 0x0B14 - DMIC<N> Data Pin Muxing
  Determines DMIC<N> Data Pin muxing. See GPIO_*_MUXING_DMIC<N>_DATA_*
**/
  UINT32                      PchHdaAudioLinkDmicDataPinMux[2];

/** Offset 0x0B1C - Enable HD Audio SSP0 Link
  Enable/disable HD Audio SSP_N/I2S link. Muxed with HDA. N-number 0-5
**/
  UINT8                       PchHdaAudioLinkSspEnable[6];

/** Offset 0x0B22 - Enable HD Audio SoundWire#N Link
  Enable/disable HD Audio SNDW#N link. Muxed with HDA.
**/
  UINT8                       PchHdaAudioLinkSndwEnable[4];

/** Offset 0x0B26 - iDisp-Link Frequency
  iDisp-Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 4: 96MHz, 3: 48MHz.
  4: 96MHz, 3: 48MHz
**/
  UINT8                       PchHdaIDispLinkFrequency;

/** Offset 0x0B27 - Reserved
**/
  UINT8                       Reserved48;

/** Offset 0x0B28 - iDisp-Link T-mode
  iDisp-Link T-Mode (PCH_HDAUDIO_IDISP_TMODE enum): 0: 2T, 2: 4T, 3: 8T, 4: 16T
  0: 2T, 2: 4T, 3: 8T, 4: 16T
**/
  UINT8                       PchHdaIDispLinkTmode;

/** Offset 0x0B29 - iDisplay Audio Codec disconnection
  0: Not disconnected, enumerable, 1: Disconnected SDI, not enumerable.
  $EN_DIS
**/
  UINT8                       PchHdaIDispCodecDisconnect;

/** Offset 0x0B2A - Reserved
**/
  UINT8                       Reserved49[6];

/** Offset 0x0B30 - CNVi DDR RFI Mitigation
  Enable/Disable DDR RFI Mitigation. Default is ENABLE. 0: DISABLE, 1: ENABLE
  $EN_DIS
**/
  UINT8                       CnviDdrRfim;

/** Offset 0x0B31 - Reserved
**/
  UINT8                       Reserved50[11];

/** Offset 0x0B3C - Debug Interfaces
  Debug Interfaces. BIT0-RAM, BIT1-UART, BIT3-USB3, BIT4-Serial IO, BIT5-TraceHub,
  BIT2 - Not used.
**/
  UINT8                       PcdDebugInterfaceFlags;

/** Offset 0x0B3D - Serial Io Uart Debug Controller Number
  Select SerialIo Uart Controller for debug.
  0:SerialIoUart0, 1:SerialIoUart1, 2:SerialIoUart2
**/
  UINT8                       SerialIoUartDebugControllerNumber;

/** Offset 0x0B3E - Serial Io Uart Debug Auto Flow
  Enables UART hardware flow control, CTS and RTS lines.
  $EN_DIS
**/
  UINT8                       SerialIoUartDebugAutoFlow;

/** Offset 0x0B3F - Reserved
**/
  UINT8                       Reserved51;

/** Offset 0x0B40 - Serial Io Uart Debug BaudRate
  Set default BaudRate Supported from 0 - default to 6000000. Recommended values 9600,
  19200, 57600, 115200, 460800, 921600, 1500000, 1843200, 3000000, 3686400, 6000000
**/
  UINT32                      SerialIoUartDebugBaudRate;

/** Offset 0x0B44 - Serial Io Uart Debug Parity
  Set default Parity.
  0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
**/
  UINT8                       SerialIoUartDebugParity;

/** Offset 0x0B45 - Serial Io Uart Debug Stop Bits
  Set default stop bits.
  0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3: TwoStopBits
**/
  UINT8                       SerialIoUartDebugStopBits;

/** Offset 0x0B46 - Serial Io Uart Debug Data Bits
  Set default word length. 0: Default, 5,6,7,8
  5:5BITS, 6:6BITS, 7:7BITS, 8:8BITS
**/
  UINT8                       SerialIoUartDebugDataBits;

/** Offset 0x0B47 - Reserved
**/
  UINT8                       Reserved52;

/** Offset 0x0B48 - Serial Io Uart Debug Mmio Base
  Select SerialIo Uart default MMIO resource in SEC/PEI phase when PcdSerialIoUartMode
  = SerialIoUartPci.
**/
  UINT32                      SerialIoUartDebugMmioBase;

/** Offset 0x0B4C - ISA Serial Base selection
  Select ISA Serial Base address. Default is 0x3F8.
  0:0x3F8, 1:0x2F8
**/
  UINT8                       PcdIsaSerialUartBase;

/** Offset 0x0B4D - Reserved
**/
  UINT8                       Reserved53;

/** Offset 0x0B4E - Ring PLL voltage offset
  Core PLL voltage offset. <b>0: No offset</b>. Range 0-15
**/
  UINT8                       RingPllVoltageOffset;

/** Offset 0x0B4F - System Agent PLL voltage offset
  Core PLL voltage offset. <b>0: No offset</b>. Range 0-15
**/
  UINT8                       SaPllVoltageOffset;

/** Offset 0x0B50 - Reserved
**/
  UINT8                       Reserved54;

/** Offset 0x0B51 - Memory Controller PLL voltage offset
  Core PLL voltage offset. <b>0: No offset</b>. Range 0-15
**/
  UINT8                       McPllVoltageOffset;

/** Offset 0x0B52 - TCSS Thunderbolt PCIE Root Port 0 Enable
  Set TCSS Thunderbolt PCIE Root Port 0. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssItbtPcie0En;

/** Offset 0x0B53 - TCSS Thunderbolt PCIE Root Port 1 Enable
  Set TCSS Thunderbolt PCIE Root Port 1. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssItbtPcie1En;

/** Offset 0x0B54 - TCSS Thunderbolt PCIE Root Port 2 Enable
  Set TCSS Thunderbolt PCIE Root Port 2. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssItbtPcie2En;

/** Offset 0x0B55 - TCSS Thunderbolt PCIE Root Port 3 Enable
  Set TCSS Thunderbolt PCIE Root Port 3. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssItbtPcie3En;

/** Offset 0x0B56 - TCSS USB HOST (xHCI) Enable
  Set TCSS XHCI. 0:Disabled  1:Enabled - Must be enabled if xDCI is enabled below
  $EN_DIS
**/
  UINT8                       TcssXhciEn;

/** Offset 0x0B57 - TCSS USB DEVICE (xDCI) Enable
  Set TCSS XDCI. 0:Disabled  1:Enabled - xHCI must be enabled if xDCI is enabled
  $EN_DIS
**/
  UINT8                       TcssXdciEn;

/** Offset 0x0B58 - TCSS DMA0 Enable
  Set TCSS DMA0. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssDma0En;

/** Offset 0x0B59 - TCSS DMA1 Enable
  Set TCSS DMA1. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssDma1En;

/** Offset 0x0B5A - PcdSerialDebugBaudRate
  Baud Rate for Serial Debug Messages. 3:9600, 4:19200, 6:56700, 7:115200.
  3:9600, 4:19200, 6:56700, 7:115200
**/
  UINT8                       PcdSerialDebugBaudRate;

/** Offset 0x0B5B - HobBufferSize
  Size to set HOB Buffer. 0:Default, 1: 1 Byte, 2: 1 KB, 3: Max value(assuming 63KB
  total HOB size).
  0:Default, 1: 1 Byte, 2: 1 KB, 3: Max value
**/
  UINT8                       HobBufferSize;

/** Offset 0x0B5C - Early Command Training
  Enables/Disable Early Command Training
  $EN_DIS
**/
  UINT8                       ECT;

/** Offset 0x0B5D - SenseAmp Offset Training
  Enables/Disable SenseAmp Offset Training
  $EN_DIS
**/
  UINT8                       SOT;

/** Offset 0x0B5E - Early ReadMPR Timing Centering 2D
  Enables/Disable Early ReadMPR Timing Centering 2D
  $EN_DIS
**/
  UINT8                       ERDMPRTC2D;

/** Offset 0x0B5F - Read MPR Training
  Enables/Disable Read MPR Training
  $EN_DIS
**/
  UINT8                       RDMPRT;

/** Offset 0x0B60 - Receive Enable Training
  Enables/Disable Receive Enable Training
  $EN_DIS
**/
  UINT8                       RCVET;

/** Offset 0x0B61 - Jedec Write Leveling
  Enables/Disable Jedec Write Leveling
  $EN_DIS
**/
  UINT8                       JWRL;

/** Offset 0x0B62 - Early Write Time Centering 2D
  Enables/Disable Early Write Time Centering 2D
  $EN_DIS
**/
  UINT8                       EWRTC2D;

/** Offset 0x0B63 - Early Read Time Centering 2D
  Enables/Disable Early Read Time Centering 2D
  $EN_DIS
**/
  UINT8                       ERDTC2D;

/** Offset 0x0B64 - Reserved
**/
  UINT8                       Reserved55;

/** Offset 0x0B65 - Write Timing Centering 1D
  Enables/Disable Write Timing Centering 1D
  $EN_DIS
**/
  UINT8                       WRTC1D;

/** Offset 0x0B66 - Write Voltage Centering 1D
  Enables/Disable Write Voltage Centering 1D
  $EN_DIS
**/
  UINT8                       WRVC1D;

/** Offset 0x0B67 - Read Timing Centering 1D
  Enables/Disable Read Timing Centering 1D
  $EN_DIS
**/
  UINT8                       RDTC1D;

/** Offset 0x0B68 - Read Voltage Centering 1D
  Enable/Disable Read Voltage Centering 1D
  $EN_DIS
**/
  UINT8                       RDVC1D;

/** Offset 0x0B69 - Reserved
**/
  UINT8                       Reserved56[10];

/** Offset 0x0B73 - Read Equalization Training
  Enables/Disable Read Equalization Training
  $EN_DIS
**/
  UINT8                       RDEQT;

/** Offset 0x0B74 - Reserved
**/
  UINT8                       Reserved57[2];

/** Offset 0x0B76 - Write Timing Centering 2D
  Enables/Disable Write Timing Centering 2D
  $EN_DIS
**/
  UINT8                       WRTC2D;

/** Offset 0x0B77 - Read Timing Centering 2D
  Enables/Disable Read Timing Centering 2D
  $EN_DIS
**/
  UINT8                       RDTC2D;

/** Offset 0x0B78 - Write Voltage Centering 2D
  Enables/Disable Write Voltage Centering 2D
  $EN_DIS
**/
  UINT8                       WRVC2D;

/** Offset 0x0B79 - Read Voltage Centering 2D
  Enables/Disable Read Voltage Centering 2D
  $EN_DIS
**/
  UINT8                       RDVC2D;

/** Offset 0x0B7A - Reserved
**/
  UINT8                       Reserved58;

/** Offset 0x0B7B - Command Voltage Centering
  Enables/Disable Command Voltage Centering
  $EN_DIS
**/
  UINT8                       CMDVC;

/** Offset 0x0B7C - Late Command Training
  Enables/Disable Late Command Training
  $EN_DIS
**/
  UINT8                       LCT;

/** Offset 0x0B7D - Turn Around Timing Training
  Enables/Disable Turn Around Timing Training
  $EN_DIS
**/
  UINT8                       TAT;

/** Offset 0x0B7E - Rank Margin Tool
  Enable/disable Rank Margin Tool
  $EN_DIS
**/
  UINT8                       RMT;

/** Offset 0x0B7F - Reserved
**/
  UINT8                       Reserved59;

/** Offset 0x0B80 - DIMM SPD Alias Test
  Enables/Disable DIMM SPD Alias Test
  $EN_DIS
**/
  UINT8                       ALIASCHK;

/** Offset 0x0B81 - Retrain Margin Check
  Enables/Disable Retrain Margin Check
  $EN_DIS
**/
  UINT8                       RMC;

/** Offset 0x0B82 - Row Hammering Prevention
  Enables/Disable Row Hammering Prevention
  $EN_DIS
**/
  UINT8                       ROWHAMMER;

/** Offset 0x0B83 - Dimm ODT Training
  Enables/Disable Dimm ODT Training
  $EN_DIS
**/
  UINT8                       DIMMODTT;

/** Offset 0x0B84 - DIMM RON Training
  Enables/Disable DIMM RON Training
  $EN_DIS
**/
  UINT8                       DIMMRONT;

/** Offset 0x0B85 - TxDqTCO Comp Training
  Enable/Disable TxDqTCO Comp Training
  $EN_DIS
**/
  UINT8                       TXTCO;

/** Offset 0x0B86 - ClkTCO Comp Training
  Enable/Disable ClkTCO Comp Training
  $EN_DIS
**/
  UINT8                       CLKTCO;

/** Offset 0x0B87 - CMD Slew Rate Training
  Enable/Disable CMD Slew Rate Training
  $EN_DIS
**/
  UINT8                       CMDSR;

/** Offset 0x0B88 - Reserved
**/
  UINT8                       Reserved60[2];

/** Offset 0x0B8A - DIMM CA ODT Training
  Enable/Disable DIMM CA ODT Training
  $EN_DIS
**/
  UINT8                       DIMMODTCA;

/** Offset 0x0B8B - Reserved
**/
  UINT8                       Reserved61[3];

/** Offset 0x0B8E - Read Vref Decap Training
  Enable/Disable Read Vref Decap Training
  $EN_DIS
**/
  UINT8                       RDVREFDC;

/** Offset 0x0B8F - Vddq Training
  Enable/Disable Vddq Training
  $EN_DIS
**/
  UINT8                       VDDQT;

/** Offset 0x0B90 - Rank Margin Tool Per Bit
  Enable/Disable Rank Margin Tool Per Bit
  $EN_DIS
**/
  UINT8                       RMTBIT;

/** Offset 0x0B91 - Reserved
**/
  UINT8                       Reserved62[4];

/** Offset 0x0B95 - Duty Cycle Correction Training
  Enable/Disable Duty Cycle Correction Training
  $EN_DIS
**/
  UINT8                       DCC;

/** Offset 0x0B96 - Reserved
**/
  UINT8                       Reserved63[17];

/** Offset 0x0BA7 - ECC Support
  Enables/Disable ECC Support
  $EN_DIS
**/
  UINT8                       EccSupport;

/** Offset 0x0BA8 - Ibecc
  In-Band ECC Support
  $EN_DIS
**/
  UINT8                       Ibecc;

/** Offset 0x0BA9 - IbeccParity
  In-Band ECC Parity Control
  $EN_DIS
**/
  UINT8                       IbeccParity;

/** Offset 0x0BAA - IbeccOperationMode
  In-Band ECC Operation Mode
  0:Protect base on address range, 1: Non-protected, 2: All protected
**/
  UINT8                       IbeccOperationMode;

/** Offset 0x0BAB - IbeccProtectedRegionEnable
  In-Band ECC Protected Region Enable
  $EN_DIS
**/
  UINT8                       IbeccProtectedRegionEnable[8];

/** Offset 0x0BB3 - Reserved
**/
  UINT8                       Reserved64;

/** Offset 0x0BB4 - IbeccProtectedRegionBases
  IBECC Protected Region Bases per IBECC instance
**/
  UINT16                      IbeccProtectedRegionBase[8];

/** Offset 0x0BC4 - IbeccProtectedRegionMasks
  IBECC Protected Region Masks
**/
  UINT16                      IbeccProtectedRegionMask[8];

/** Offset 0x0BD4 - IbeccProtectedRegionOverallBases
  IBECC Protected Region Bases based on enabled IBECC instance
**/
  UINT16                      IbeccProtectedRegionOverallBase[8];

/** Offset 0x0BE4 - Memory Remap
  Enables/Disable Memory Remap
  $EN_DIS
**/
  UINT8                       RemapEnable;

/** Offset 0x0BE5 - Rank Interleave support
  Enables/Disable Rank Interleave support. NOTE: RI and HORI can not be enabled at
  the same time.
  $EN_DIS
**/
  UINT8                       RankInterleave;

/** Offset 0x0BE6 - Enhanced Interleave support
  Enables/Disable Enhanced Interleave support
  $EN_DIS
**/
  UINT8                       EnhancedInterleave;

/** Offset 0x0BE7 - Ch Hash Support
  Enable/Disable Channel Hash Support. NOTE: ONLY if Memory interleaved Mode
  $EN_DIS
**/
  UINT8                       ChHashEnable;

/** Offset 0x0BE8 - Extern Therm Status
  Enables/Disable Extern Therm Status
  $EN_DIS
**/
  UINT8                       EnableExtts;

/** Offset 0x0BE9 - DDR PowerDown and idle counter
  Enables/Disable DDR PowerDown and idle counter(For LPDDR Only)
  $EN_DIS
**/
  UINT8                       EnablePwrDn;

/** Offset 0x0BEA - DDR PowerDown and idle counter
  Enables/Disable DDR PowerDown and idle counter(For LPDDR Only)
  $EN_DIS
**/
  UINT8                       EnablePwrDnLpddr;

/** Offset 0x0BEB - SelfRefresh Enable
  Enables/Disable SelfRefresh Enable
  $EN_DIS
**/
  UINT8                       SrefCfgEna;

/** Offset 0x0BEC - Throttler CKEMin Defeature
  Enables/Disable Throttler CKEMin Defeature(For LPDDR Only)
  $EN_DIS
**/
  UINT8                       ThrtCkeMinDefeatLpddr;

/** Offset 0x0BED - Throttler CKEMin Defeature
  Enables/Disable Throttler CKEMin Defeature
  $EN_DIS
**/
  UINT8                       ThrtCkeMinDefeat;

/** Offset 0x0BEE - Row Hammer Select
  Row Hammer Select
  0:Disable, 1:RFM, 2:pTRR
**/
  UINT8                       RhSelect;

/** Offset 0x0BEF - Exit On Failure (MRC)
  Enables/Disable Exit On Failure (MRC)
  $EN_DIS
**/
  UINT8                       ExitOnFailure;

/** Offset 0x0BF0 - Reserved
**/
  UINT8                       Reserved65[4];

/** Offset 0x0BF4 - Select if ZQ pin is shared between Rank0 and Rank1 in DDR4 DDP
  ESelect if ZQ pin is shared between Rank0 and Rank1 in DDR4 DDP
  $EN_DIS
**/
  UINT8                       Ddr4DdpSharedZq;

/** Offset 0x0BF5 - Ch Hash Interleaved Bit
  Select the BIT to be used for Channel Interleaved mode. NOTE: BIT7 will interlave
  the channels at a 2 cacheline granularity, BIT8 at 4 and BIT9 at 8. Default is BIT8
  0:BIT6, 1:BIT7, 2:BIT8, 3:BIT9, 4:BIT10, 5:BIT11, 6:BIT12, 7:BIT13
**/
  UINT8                       ChHashInterleaveBit;

/** Offset 0x0BF6 - Ch Hash Mask
  Set the BIT(s) to be included in the XOR function. NOTE BIT mask corresponds to
  BITS [19:6] Default is 0x30CC
**/
  UINT16                      ChHashMask;

/** Offset 0x0BF8 - Base reference clock value
  Base reference clock value, in Hertz(Default is 125Hz)
  100000000:100Hz, 125000000:125Hz, 167000000:167Hz, 250000000:250Hz
**/
  UINT32                      BClkFrequency;

/** Offset 0x0BFC - EPG DIMM Idd3N
  Active standby current (Idd3N) in milliamps from datasheet. Must be calculated on
  a per DIMM basis. Default is 26
**/
  UINT16                      Idd3n;

/** Offset 0x0BFE - EPG DIMM Idd3P
  Active power-down current (Idd3P) in milliamps from datasheet. Must be calculated
  on a per DIMM basis. Default is 11
**/
  UINT16                      Idd3p;

/** Offset 0x0C00 - CMD Normalization
  Enable/Disable CMD Normalization
  $EN_DIS
**/
  UINT8                       CMDNORM;

/** Offset 0x0C01 - Early DQ Write Drive Strength and Equalization Training
  Enable/Disable Early DQ Write Drive Strength and Equalization Training
  $EN_DIS
**/
  UINT8                       EWRDSEQ;

/** Offset 0x0C02 - Idle Energy Mc0Ch0Dimm0
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc0Ch0Dimm0;

/** Offset 0x0C03 - Idle Energy Mc0Ch0Dimm1
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc0Ch0Dimm1;

/** Offset 0x0C04 - Idle Energy Mc0Ch1Dimm0
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc0Ch1Dimm0;

/** Offset 0x0C05 - Idle Energy Mc0Ch1Dimm1
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc0Ch1Dimm1;

/** Offset 0x0C06 - Idle Energy Mc1Ch0Dimm0
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc1Ch0Dimm0;

/** Offset 0x0C07 - Idle Energy Mc1Ch0Dimm1
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc1Ch0Dimm1;

/** Offset 0x0C08 - Idle Energy Mc1Ch1Dimm0
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc1Ch1Dimm0;

/** Offset 0x0C09 - Idle Energy Mc1Ch1Dimm1
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc1Ch1Dimm1;

/** Offset 0x0C0A - PowerDown Energy Mc0Ch0Dimm0
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc0Ch0Dimm0;

/** Offset 0x0C0B - PowerDown Energy Mc0Ch0Dimm1
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc0Ch0Dimm1;

/** Offset 0x0C0C - PowerDown Energy Mc0Ch1Dimm0
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc0Ch1Dimm0;

/** Offset 0x0C0D - PowerDown Energy Mc0Ch1Dimm1
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc0Ch1Dimm1;

/** Offset 0x0C0E - PowerDown Energy Mc1Ch0Dimm0
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc1Ch0Dimm0;

/** Offset 0x0C0F - PowerDown Energy Mc1Ch0Dimm1
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc1Ch0Dimm1;

/** Offset 0x0C10 - PowerDown Energy Mc1Ch1Dimm0
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc1Ch1Dimm0;

/** Offset 0x0C11 - PowerDown Energy Mc1Ch1Dimm1
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc1Ch1Dimm1;

/** Offset 0x0C12 - Activate Energy Mc0Ch0Dimm0
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc0Ch0Dimm0;

/** Offset 0x0C13 - Activate Energy Mc0Ch0Dimm1
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc0Ch0Dimm1;

/** Offset 0x0C14 - Activate Energy Mc0Ch1Dimm0
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc0Ch1Dimm0;

/** Offset 0x0C15 - Activate Energy Mc0Ch1Dimm1
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc0Ch1Dimm1;

/** Offset 0x0C16 - Activate Energy Mc1Ch0Dimm0
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc1Ch0Dimm0;

/** Offset 0x0C17 - Activate Energy Mc1Ch0Dimm1
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc1Ch0Dimm1;

/** Offset 0x0C18 - Activate Energy Mc1Ch1Dimm0
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc1Ch1Dimm0;

/** Offset 0x0C19 - Activate Energy Mc1Ch1Dimm1
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc1Ch1Dimm1;

/** Offset 0x0C1A - Read Energy Mc0Ch0Dimm0
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc0Ch0Dimm0;

/** Offset 0x0C1B - Read Energy Mc0Ch0Dimm1
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc0Ch0Dimm1;

/** Offset 0x0C1C - Read Energy Mc0Ch1Dimm0
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc0Ch1Dimm0;

/** Offset 0x0C1D - Read Energy Mc0Ch1Dimm1
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc0Ch1Dimm1;

/** Offset 0x0C1E - Read Energy Mc1Ch0Dimm0
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc1Ch0Dimm0;

/** Offset 0x0C1F - Read Energy Mc1Ch0Dimm1
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc1Ch0Dimm1;

/** Offset 0x0C20 - Read Energy Mc1Ch1Dimm0
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc1Ch1Dimm0;

/** Offset 0x0C21 - Read Energy Mc1Ch1Dimm1
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc1Ch1Dimm1;

/** Offset 0x0C22 - Write Energy Mc0Ch0Dimm0
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc0Ch0Dimm0;

/** Offset 0x0C23 - Write Energy Mc0Ch0Dimm1
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc0Ch0Dimm1;

/** Offset 0x0C24 - Write Energy Mc0Ch1Dimm0
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc0Ch1Dimm0;

/** Offset 0x0C25 - Write Energy Mc0Ch1Dimm1
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc0Ch1Dimm1;

/** Offset 0x0C26 - Write Energy Mc1Ch0Dimm0
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc1Ch0Dimm0;

/** Offset 0x0C27 - Write Energy Mc1Ch0Dimm1
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc1Ch0Dimm1;

/** Offset 0x0C28 - Write Energy Mc1Ch1Dimm0
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc1Ch1Dimm0;

/** Offset 0x0C29 - Write Energy Mc1Ch1Dimm1
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc1Ch1Dimm1;

/** Offset 0x0C2A - Throttler CKEMin Timer
  Timer value for CKEMin, range[255;0]. Req'd min of SC_ROUND_T + BYTE_LENGTH (4).
  Dfault is 0x00
**/
  UINT8                       ThrtCkeMinTmr;

/** Offset 0x0C2B - Reserved
**/
  UINT8                       Reserved66[2];

/** Offset 0x0C2D - Rapl Power Floor Ch0
  Power budget ,range[255;0],(0= 5.3W Def)
**/
  UINT8                       RaplPwrFlCh0;

/** Offset 0x0C2E - Rapl Power Floor Ch1
  Power budget ,range[255;0],(0= 5.3W Def)
**/
  UINT8                       RaplPwrFlCh1;

/** Offset 0x0C2F - Command Rate Support
  CMD Rate and Limit Support Option. NOTE: ONLY supported in 1N Mode, Default is 3 CMDs
  0:Disable, 5:2 CMDS, 7:3 CMDS, 9:4 CMDS, 11:5 CMDS, 13:6 CMDS, 15:7 CMDS
**/
  UINT8                       EnCmdRate;

/** Offset 0x0C30 - MC_REFRESH_RATE
  Type of Refresh Rate used to prevent Row Hammer. Default is NORMAL Refresh
  0:NORMAL Refresh, 1:1x Refresh, 2:2x Refresh, 3:4x Refresh
**/
  UINT8                       McRefreshRate;

/** Offset 0x0C31 - Energy Performance Gain
  Enable/disable Energy Performance Gain. <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       EpgEnable;

/** Offset 0x0C32 - RH pTRR LFSR0 Mask
  Row Hammer pTRR LFSR0 Mask, 1/2^(value)
**/
  UINT8                       Lfsr0Mask;

/** Offset 0x0C33 - User Manual Threshold
  Disabled: Predefined threshold will be used.\n
  Enabled: User Input will be used.
  $EN_DIS
**/
  UINT8                       UserThresholdEnable;

/** Offset 0x0C34 - User Manual Budget
  Disabled: Configuration of memories will defined the Budget value.\n
  Enabled: User Input will be used.
  $EN_DIS
**/
  UINT8                       UserBudgetEnable;

/** Offset 0x0C35 - Reserved
**/
  UINT8                       Reserved67;

/** Offset 0x0C36 - Power Down Mode
  This option controls command bus tristating during idle periods
  0x0:No Power Down, 0x1:APD, 0x6:PPD DLL OFF, 0xFF:Auto
**/
  UINT8                       PowerDownMode;

/** Offset 0x0C37 - Pwr Down Idle Timer
  The minimum value should = to the worst case Roundtrip delay + Burst_Length. 0 means
  AUTO: 64 for ULX/ULT, 128 for DT/Halo
**/
  UINT8                       PwdwnIdleCounter;

/** Offset 0x0C38 - Page Close Idle Timeout
  This option controls Page Close Idle Timeout
  0:Enabled, 1:Disabled
**/
  UINT8                       DisPgCloseIdleTimeout;

/** Offset 0x0C39 - Bitmask of ranks that have CA bus terminated
  Offset 225 LPDDR4: Bitmask of ranks that have CA bus terminated. <b>0x01=Default,
  Rank0 is terminating and Rank1 is non-terminating</b>
**/
  UINT8                       CmdRanksTerminated;

/** Offset 0x0C3A - PcdSerialDebugLevel
  Serial Debug Message Level. 0:Disable, 1:Error Only, 2:Error & Warnings, 3:Load,
  Error, Warnings & Info, 4:Load, Error, Warnings, Info & Event, 5:Load, Error, Warnings,
  Info & Verbose.
  0:Disable, 1:Error Only, 2:Error and Warnings, 3:Load Error Warnings and Info, 4:Load
  Error Warnings and Info & Event, 5:Load Error Warnings Info and Verbose
**/
  UINT8                       PcdSerialDebugLevel;

/** Offset 0x0C3B - Reserved
**/
  UINT8                       Reserved68[8];

/** Offset 0x0C43 - Ask MRC to clear memory content
  Ask MRC to clear memory content <b>0: Do not Clear Memory;</b> 1: Clear Memory.
  $EN_DIS
**/
  UINT8                       CleanMemory;

/** Offset 0x0C44 - TCSS USB Port Enable
  Bitmap for per port enabling
**/
  UINT8                       UsbTcPortEnPreMem;

/** Offset 0x0C45 - Reserved
**/
  UINT8                       Reserved69;

/** Offset 0x0C46 - Post Code Output Port
  This option configures Post Code Output Port
**/
  UINT16                      PostCodeOutputPort;

/** Offset 0x0C48 - RMTLoopCount
  Specifies the Loop Count to be used during Rank Margin Tool Testing. 0 - AUTO
**/
  UINT8                       RMTLoopCount;

/** Offset 0x0C49 - Enable/Disable SA CRID
  Enable: SA CRID, Disable (Default): SA CRID
  $EN_DIS
**/
  UINT8                       CridEnable;

/** Offset 0x0C4A - Reserved
**/
  UINT8                      Reserved70[2];

/** Offset 0x0C4C - BCLK RFI Frequency
  Bclk RFI Frequency for each SAGV point in Hz units. 98000000Hz = 98MHz <b>0 - No
  RFI Tuning</b>. Range is 98Mhz-100Mhz.
**/
  UINT32                      BclkRfiFreq[4];

/** Offset 0x0C5C - Size of PCIe IMR.
  Size of PCIe IMR in megabytes
**/
  UINT16                      PcieImrSize;

/** Offset 0x0C5E - Enable PCIe IMR
  0: Disable(AUTO), 1: Enable
  $EN_DIS
**/
  UINT8                       PcieImrEnabled;

/** Offset 0x0C5F - Enable PCIe IMR
  1: PCH PCIE, 2: SA PCIE. If PCIeImrEnabled is TRUE then this will use to select
  the Root port location from PCH PCIe or SA PCIe
  $EN_DIS
**/
  UINT8                       PcieImrRpLocation;

/** Offset 0x0C60 - Root port number for IMR.
  Root port number for IMR.If PCieImrRpLocation is PCH PCIe then select root port
  from 0 to 23 and if it is SA PCIe then select root port from 0 to 3
**/
  UINT8                       PcieImrRpSelection;

/** Offset 0x0C61 - SerialDebugMrcLevel
  MRC Serial Debug Message Level. 0:Disable, 1:Error Only, 2:Error & Warnings, 3:Load,
  Error, Warnings & Info, 4:Load, Error, Warnings, Info & Event, 5:Load, Error, Warnings,
  Info & Verbose.
  0:Disable, 1:Error Only, 2:Error and Warnings, 3:Load Error Warnings and Info, 4:Load
  Error Warnings and Info & Event, 5:Load Error Warnings Info and Verbose
**/
  UINT8                       SerialDebugMrcLevel;

/** Offset 0x0C62 - Reserved
**/
  UINT8                       Reserved71[11];

/** Offset 0x0C6D - RH pTRR LFSR1 Mask
  Row Hammer pTRR LFSR1 Mask, 1/2^(value)
**/
  UINT8                       Lfsr1Mask;

/** Offset 0x0C6E - Reserved
**/
  UINT8                       Reserved72;

/** Offset 0x0C6F - Command Pins Mapping
  BitMask where bits [3:0] are Controller 0 Channel [3:0] and bits [7:4] are Controller
  1 Channel [3:0]. 0 = CCC pin mapping is Ascending, 1 = CCC pin mapping is Descending.
**/
  UINT8                       Lp5CccConfig;

/** Offset 0x0C70 - Command Pins Mirrored
  BitMask where bits [3:0] are Controller 0 Channel [3:0] and bits [7:4] are Controller
  1 Channel [3:0]. 0 = No Command Mirror and 1 = Command Mirror.
**/
  UINT8                       CmdMirror;

/** Offset 0x0C71 - Reserved
**/
  UINT8                       Reserved73[3];

/** Offset 0x0C74 - LowerBasicMemTestSize
  Reduce BasicMemoryTest size WA: 0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       LowerBasicMemTestSize;

/** Offset 0x0C75 - Reserved
**/
  UINT8                       Reserved74[20];

/** Offset 0x0C89 - Skip external display device scanning
  Enable: Do not scan for external display device, Disable (Default): Scan external
  display devices
  $EN_DIS
**/
  UINT8                       SkipExtGfxScan;

/** Offset 0x0C8A - Generate BIOS Data ACPI Table
  Enable: Generate BDAT for MRC RMT or SA PCIe data. Disable (Default): Do not generate it
  $EN_DIS
**/
  UINT8                       BdatEnable;

/** Offset 0x0C8B - Lock PCU Thermal Management registers
  Lock PCU Thermal Management registers. Enable(Default)=1, Disable=0
  $EN_DIS
**/
  UINT8                       LockPTMregs;

/** Offset 0x0C8C - Panel Power Enable
  Control for enabling/disabling VDD force bit (Required only for early enabling of
  eDP panel). 0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       PanelPowerEnable;

/** Offset 0x0C8D - BdatTestType
  Indicates the type of Memory Training data to populate into the BDAT ACPI table.
  0:RMT per Rank, 1:RMT per Bit, 2:Margin2D
**/
  UINT8                       BdatTestType;

/** Offset 0x0C8E - Reserved
**/
  UINT8                       Reserved75[2];

/** Offset 0x0C90 - PMR Size
  Size of PMR memory buffer. 0x400000 for normal boot and 0x200000 for S3 boot
**/
  UINT32                      DmaBufferSize;

/** Offset 0x0C94 - The policy for VTd driver behavior
  BIT0: Enable IOMMU during boot, BIT1: Enable IOMMU when transfer control to OS
**/
  UINT8                       PreBootDmaMask;

/** Offset 0x0C95 - Reserved
**/
  UINT8                       Reserved76[5];

/** Offset 0x0C9A - Platform LID Status for LFP Displays.
  LFP Display Lid Status (LID_STATUS enum): 0 (Default): LidClosed, 1: LidOpen.
  0: LidClosed, 1: LidOpen
**/
  UINT8                       LidStatus;

/** Offset 0x0C9B - Control VGA Initialition sequence
  Initialise VGA Init, Set BIT0 - 0 (No VGA Support), BIT0 = 1 (VGA Supported) BIT1
  = 1 (VGA Exit)
  0x0: NO VGA Init, 0x1: VGA Init, 0x3: VGA Init and VGA Exit
**/
  UINT8                       VgaInitControl;

/** Offset 0x0C9C - Graphics Configuration Ptr
  Points to VBT
**/
  UINT32                      VbtPtr;

/** Offset 0x0CA0 - Intel Graphics VBT (Video BIOS Table) Size
  Size of Graphics VBT Image
**/
  UINT32                      VbtSize;

/** Offset 0x0CA4 - VGA Training Message Pointer
  Points to VGA Message Array
**/
  UINT32                      VgaMessage;

/** Offset 0x0CA8 - Reserved
**/
  UINT8                       Reserved77[124];

/** Offset 0x0D24 - TotalFlashSize
  Enable/Disable. 0: Disable, define default value of TotalFlashSize , 1: enable
**/
  UINT16                      TotalFlashSize;

/** Offset 0x0D26 - BiosSize
  The size of the BIOS region of the IFWI. Used if FspmUpd->FspmConfig.BiosGuard !=
  0. If BiosGuard is enabled, MRC will increase the size of the DPR (DMA Protected
  Range) so that a BIOS Update Script can be stored in the DPR.
**/
  UINT16                      BiosSize;

/** Offset 0x0D28 - Reserved
**/
  UINT8                       Reserved78[28];

/** Offset 0x0D44 - Smbus dynamic power gating
  Disable or Enable Smbus dynamic power gating.
  $EN_DIS
**/
  UINT8                       SmbusDynamicPowerGating;

/** Offset 0x0D45 - Disable and Lock Watch Dog Register
  Set 1 to clear WDT status, then disable and lock WDT registers.
  $EN_DIS
**/
  UINT8                       WdtDisableAndLock;

/** Offset 0x0D46 - Reserved
**/
  UINT8                       Reserved79[2];

/** Offset 0x0D48 - SMBUS SPD Write Disable
  Set/Clear Smbus SPD Write Disable. 0: leave SPD Write Disable bit; 1: set SPD Write
  Disable bit. For security recommendations, SPD write disable bit must be set.
  $EN_DIS
**/
  UINT8                       SmbusSpdWriteDisable;

/** Offset 0x0D49 - Reserved
**/
  UINT8                       Reserved80[34];

/** Offset 0x0D6B - HECI Timeouts
  0: Disable, 1: Enable (Default) timeout check for HECI
  $EN_DIS
**/
  UINT8                       HeciTimeouts;

/** Offset 0x0D6C - Force ME DID Init Status
  Test, 0: disable, 1: Success, 2: No Memory in Channels, 3: Memory Init Error, Set
  ME DID init stat value
  $EN_DIS
**/
  UINT8                       DidInitStat;

/** Offset 0x0D6D - CPU Replaced Polling Disable
  Test, 0: disable, 1: enable, Setting this option disables CPU replacement polling loop
  $EN_DIS
**/
  UINT8                       DisableCpuReplacedPolling;

/** Offset 0x0D6E - Check HECI message before send
  Test, 0: disable, 1: enable, Enable/Disable message check.
  $EN_DIS
**/
  UINT8                       DisableMessageCheck;

/** Offset 0x0D6F - Skip MBP HOB
  Test, 0: disable, 1: enable, Enable/Disable sending MBP message and creating MBP Hob.
  $EN_DIS
**/
  UINT8                       SkipMbpHob;

/** Offset 0x0D70 - HECI2 Interface Communication
  Test, 0: disable, 1: enable, Adds or Removes HECI2 Device from PCI space.
  $EN_DIS
**/
  UINT8                       HeciCommunication2;

/** Offset 0x0D71 - Enable KT device
  Test, 0: POR, 1: enable, 2: disable, Enable or Disable KT device.
  $EN_DIS
**/
  UINT8                       KtDeviceEnable;

/** Offset 0x0D72 - Skip CPU replacement check
  Test, 0: disable, 1: enable, Setting this option to skip CPU replacement check
  $EN_DIS
**/
  UINT8                       SkipCpuReplacementCheck;

/** Offset 0x0D73 - Reserved
**/
  UINT8                       Reserved81[100];

/** Offset 0x0DD7 - Avx2 Voltage Guardband Scaling Factor
  AVX2 Voltage Guardband Scale factor applied to AVX2 workloads. Range is 0-200 in
  1/100 units, where a value of 125 would apply a 1.25 scale factor.
**/
  UINT8                       Avx2VoltageScaleFactor;

/** Offset 0x0DD8 - Avx512 Voltage Guardband Scaling Factor
  DEPRECATED. AVX512 Voltage Guardband Scale factor applied to AVX512 workloads. Range
  is 0-200 in 1/100 units, where a value of 125 would apply a 1.25 scale factor.
**/
  UINT8                       Avx512VoltageScaleFactor;

/** Offset 0x0DD9 - Serial Io Uart Debug Mode
  Select SerialIo Uart Controller mode
  0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
  4:SerialIoUartSkipInit
**/
  UINT8                       SerialIoUartDebugMode;

/** Offset 0x0DDA - Reserved
**/
  UINT8                      Reserved82[2];

/** Offset 0x0DDC - SerialIoUartDebugRxPinMux - FSPM
  Select RX pin muxing for SerialIo UART used for debug
**/
  UINT32                      SerialIoUartDebugRxPinMux;

/** Offset 0x0DE0 - SerialIoUartDebugTxPinMux - FSPM
  Select TX pin muxing for SerialIo UART used for debug
**/
  UINT32                      SerialIoUartDebugTxPinMux;

/** Offset 0x0DE4 - SerialIoUartDebugRtsPinMux - FSPM
  Select SerialIo Uart used for debug Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
  for possible values.
**/
  UINT32                      SerialIoUartDebugRtsPinMux;

/** Offset 0x0DE8 - SerialIoUartDebugCtsPinMux - FSPM
  Select SerialIo Uart used for debug Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
  for possible values.
**/
  UINT32                      SerialIoUartDebugCtsPinMux;

/** Offset 0x0DEC - Reserved
**/
  UINT8                      Reserved83[164];

/** Offset 0x0E90 - TME Exclude Base Address
  TME Exclude Base Address.
**/
  UINT64                      TmeExcludeBase;

/** Offset 0x0E98 - TME Exclude Size Value
  TME Exclude Size Value.
**/
  UINT64                      TmeExcludeSize;

/** Offset 0x0EA0 - Generate New TME Key
  Enable: Generate New TME Key, Disable(Default): TME key determine by type of reset
  $EN_DIS
**/
  UINT8                       GenerateNewTmeKey;

/** Offset 0x0EA1 - Reserved
**/
  UINT8                       Reserved84[23];
} FSP_M_CONFIG;

/** Fsp M UPD Configuration
**/
typedef struct {

/** Offset 0x0000
**/
  FSP_UPD_HEADER              FspUpdHeader;

/** Offset 0x0020
**/
  FSPM_ARCH_UPD               FspmArchUpd;

/** Offset 0x0040
**/
  FSP_M_CONFIG                FspmConfig;

/** Offset 0x0EB8
**/
  UINT8                       Rsvd500[6];

/** Offset 0x0EBE
**/
  UINT16                      UpdTerminator;
} FSPM_UPD;

#pragma pack()

#endif