/* SPDX-License-Identifier: GPL-2.0-only */

#include <arch/cache.h>
#include <boot/coreboot_tables.h>
#include <console/console.h>
#include <delay.h>
#include <device/device.h>
#include <device/i2c_simple.h>
#include <drivers/ti/tps65090/tps65090.h>
#include <soc/clk.h>
#include <soc/dp.h>
#include <soc/dp-core.h>
#include <soc/gpio.h>
#include <soc/i2c.h>
#include <soc/periph.h>
#include <soc/power.h>
#include <soc/tmu.h>
#include <soc/usb.h>
#include <symbols.h>
#include <framebuffer_info.h>

#include "exynos5250.h"

#define MMC0_GPIO_PIN	(58)

/* convenient shorthand (in MB) */
#define DRAM_START	((uintptr_t)_dram/MiB)
#define DRAM_SIZE	CONFIG_DRAM_SIZE_MB
#define DRAM_END	(DRAM_START + DRAM_SIZE)	/* plus one... */

/* TODO: transplanted DP stuff, clean up once we have something that works */
static enum exynos5_gpio_pin dp_pd_l = GPIO_Y25;	/* active low */
static enum exynos5_gpio_pin dp_rst_l = GPIO_X15;	/* active low */
static enum exynos5_gpio_pin dp_hpd = GPIO_X07;		/* active high */

static void exynos_dp_bridge_setup(void)
{
	exynos_pinmux_dphpd();

	gpio_set_value(dp_pd_l, 1);
	gpio_cfg_pin(dp_pd_l, GPIO_OUTPUT);
	gpio_set_pull(dp_pd_l, GPIO_PULL_NONE);

	gpio_set_value(dp_rst_l, 0);
	gpio_cfg_pin(dp_rst_l, GPIO_OUTPUT);
	gpio_set_pull(dp_rst_l, GPIO_PULL_NONE);
	udelay(10);
	gpio_set_value(dp_rst_l, 1);
}

static void exynos_dp_bridge_init(void)
{
	/* De-assert PD (and possibly RST) to power up the bridge */
	gpio_set_value(dp_pd_l, 1);
	gpio_set_value(dp_rst_l, 1);

	/*
	 * We need to wait for 90ms after bringing up the bridge since
	 * there is a phantom "high" on the HPD chip during its
	 * bootup.  The phantom high comes within 7ms of de-asserting
	 * PD and persists for at least 15ms.  The real high comes
	 * roughly 50ms after PD is de-asserted. The phantom high
	 * makes it hard for us to know when the NXP chip is up.
	 */
	udelay(90000);
}

static int exynos_dp_hotplug(void)
{
	/* Check HPD.  If it's high, we're all good. */
	return gpio_get_value(dp_hpd) ? 0 : 1;
}

static void exynos_dp_reset(void)
{
	gpio_set_value(dp_pd_l, 0);
	gpio_set_value(dp_rst_l, 0);
	/* paranoid delay period (300ms) */
	udelay(300 * 1000);
}

/*
 * This delay is T3 in the LCD timing spec (defined as >200ms). We set
 * this down to 60ms since that's the approximate maximum amount of time
 * it'll take a bridge to start outputting LVDS data. The delay of
 * >200ms is just a conservative value to avoid turning on the backlight
 * when there's random LCD data on the screen. Shaving 140ms off the
 * boot is an acceptable trade-off.
 */
#define LCD_T3_DELAY_MS	60

#define LCD_T5_DELAY_MS	10
#define LCD_T6_DELAY_MS	10

static void backlight_pwm(void)
{
	/*Configure backlight PWM as a simple output high (100% brightness) */
	gpio_direction_output(GPIO_B20, 1);
	udelay(LCD_T6_DELAY_MS * 1000);
}

static void backlight_en(void)
{
	/* Configure GPIO for LCD_BL_EN */
	gpio_direction_output(GPIO_X30, 1);
}

#define TPS65090_BUS	4	/* Daisy-specific */

#define FET1_CTRL	0x0f
#define FET4_CTRL	0x12
#define FET6_CTRL	0x14

static void lcd_vdd(void)
{
	/* Enable FET6, lcd panel */
	tps65090_fet_enable(TPS65090_BUS, FET6_CTRL);
}

static void backlight_vdd(void)
{
	/* Enable FET1, backlight */
	tps65090_fet_enable(TPS65090_BUS, FET1_CTRL);
	udelay(LCD_T5_DELAY_MS * 1000);
}

static void sdmmc_vdd(void)
{
	/* Enable FET4, P3.3V_SDCARD */
	tps65090_fet_enable(TPS65090_BUS, FET4_CTRL);
}

static enum exynos5_gpio_pin usb_host_vbus = GPIO_X11;
static enum exynos5_gpio_pin usb_drd_vbus = GPIO_X27;
/* static enum exynos5_gpio_pin hsic_reset_l = GPIO_E10; */

static void prepare_usb(void)
{
	/* Kick this reset off early so it gets at least 100ms to settle */
	reset_usb_drd_dwc3();
}

static void setup_usb(void)
{
	/* HSIC not needed in firmware on this board */
	setup_usb_drd_phy();
	setup_usb_drd_dwc3();
	setup_usb_host_phy(0);

	gpio_direction_output(usb_host_vbus, 1);
	gpio_direction_output(usb_drd_vbus, 1);
}

//static struct video_info smdk5250_dp_config = {
static struct video_info dp_video_info = {
	/* FIXME: fix video_info struct to use const for name */
	.name			= (char *)"eDP-LVDS NXP PTN3460",

	.h_sync_polarity	= 0,
	.v_sync_polarity	= 0,
	.interlaced		= 0,

	.color_space		= COLOR_RGB,
	.dynamic_range		= VESA,
	.ycbcr_coeff		= COLOR_YCBCR601,
	.color_depth		= COLOR_8,

	.link_rate		= LINK_RATE_2_70GBPS,
	.lane_count		= LANE_COUNT2,
};

/* FIXME: move some place more appropriate */
#define MAX_DP_TRIES	5

/*
 * This function disables the USB3.0 PLL to save power
 */
static void disable_usb30_pll(void)
{
	enum exynos5_gpio_pin usb3_pll_l = GPIO_Y11;

	gpio_direction_output(usb3_pll_l, 0);
}

static void setup_storage(void)
{
	/* MMC0: Fixed, 8 bit mode, connected with GPIO. */
	if (clock_set_mshci(PERIPH_ID_SDMMC0))
		printk(BIOS_CRIT, "%s: Failed to set MMC0 clock.\n", __func__);
	if (gpio_direction_output(MMC0_GPIO_PIN, 1)) {
		printk(BIOS_CRIT, "%s: Unable to power on MMC0.\n", __func__);
	}
	gpio_set_pull(MMC0_GPIO_PIN, GPIO_PULL_NONE);
	gpio_set_drv(MMC0_GPIO_PIN, GPIO_DRV_4X);
	exynos_pinmux_sdmmc0();

	/* MMC2: Removable, 4 bit mode, no GPIO. */
	/* (Must be after romstage to avoid breaking SDMMC boot.) */
	clock_set_mshci(PERIPH_ID_SDMMC2);
	exynos_pinmux_sdmmc2();
}

static void gpio_init(void)
{
	/* Set up the I2C busses. */
	exynos_pinmux_i2c0();
	exynos_pinmux_i2c1();
	exynos_pinmux_i2c2();
	exynos_pinmux_i2c3();
	exynos_pinmux_i2c4();
	exynos_pinmux_i2c7();

	/* Set up the GPIOs used to arbitrate for I2C bus 4. */
	gpio_set_pull(GPIO_F03, GPIO_PULL_NONE);
	gpio_set_pull(GPIO_E04, GPIO_PULL_NONE);
	gpio_direction_output(GPIO_F03, 1);
	gpio_direction_input(GPIO_E04);

	/* Set up the GPIO used to enable the audio codec. */
	gpio_set_pull(GPIO_X17, GPIO_PULL_NONE);
	gpio_set_pull(GPIO_X15, GPIO_PULL_NONE);
	gpio_direction_output(GPIO_X17, 1);
	gpio_direction_output(GPIO_X15, 1);

	/* Set up the I2S busses. */
	exynos_pinmux_i2s0();
	exynos_pinmux_i2s1();
}

/* this happens after cpu_init where exynos resources are set */
static void mainboard_init(struct device *dev)
{
	int dp_tries;
	struct s5p_dp_device dp_device = {
		.base = exynos_dp1,
		.video_info = &dp_video_info,
	};
	void *fb_addr = (void *)(get_fb_base_kb() * KiB);

	prepare_usb();
	gpio_init();
	setup_storage();

	i2c_init(TPS65090_BUS, I2C_0_SPEED, I2C_SLAVE);
	i2c_init(7, I2C_0_SPEED, I2C_SLAVE);

	tmu_init(&exynos5250_tmu_info);

	/* Clock Gating all the unused IP's to save power */
	clock_gate();

	/* Disable USB3.0 PLL to save 250mW of power */
	disable_usb30_pll();

	sdmmc_vdd();

	fb_add_framebuffer_info((uintptr_t)fb_addr, 1366, 768, 2 * 1366, 16);

	lcd_vdd();

	// FIXME: should timeout
	do {
		udelay(50);
	} while (!exynos_dp_hotplug());

	exynos_dp_bridge_setup();
	for (dp_tries = 1; dp_tries <= MAX_DP_TRIES; dp_tries++) {
		exynos_dp_bridge_init();
		if (exynos_dp_hotplug()) {
			exynos_dp_reset();
			continue;
		}

		if (dp_controller_init(&dp_device))
			continue;

		udelay(LCD_T3_DELAY_MS * 1000);

		backlight_vdd();
		backlight_pwm();
		backlight_en();
		/* if we're here, we're successful */
		break;
	}

	if (dp_tries > MAX_DP_TRIES)
		printk(BIOS_ERR, "%s: Failed to set up displayport\n", __func__);

	setup_usb();

	// Uncomment to get excessive GPIO output:
	// gpio_info();
}

static void mainboard_enable(struct device *dev)
{
	dev->ops->init = &mainboard_init;

	/* set up dcache and MMU */
	/* FIXME: this should happen via resource allocator */
	exynos5250_config_l2_cache();
	mmu_init();
	mmu_config_range(0, DRAM_START, DCACHE_OFF);
	mmu_config_range(DRAM_START, DRAM_SIZE, DCACHE_WRITEBACK);
	mmu_config_range((uintptr_t)_dma_coherent/MiB,
			 REGION_SIZE(dma_coherent)/MiB, DCACHE_OFF);
	mmu_config_range(DRAM_END, 4096 - DRAM_END, DCACHE_OFF);
	dcache_mmu_enable();

	const unsigned int epll_hz = 192000000;
	const unsigned int sample_rate = 48000;
	const unsigned int lr_frame_size = 256;
	clock_epll_set_rate(epll_hz);
	clock_select_i2s_clk_source();
	clock_set_i2s_clk_prescaler(epll_hz, sample_rate * lr_frame_size);

	power_enable_xclkout();
}

struct chip_operations mainboard_ops = {
	.name		= "daisy",
	.enable_dev	= mainboard_enable,
};

void lb_board(struct lb_header *header)
{
	struct lb_range *dma;

	dma = (struct lb_range *)lb_new_record(header);
	dma->tag = LB_TAG_DMA;
	dma->size = sizeof(*dma);
	dma->range_start = (uintptr_t)_dma_coherent;
	dma->range_size = REGION_SIZE(dma_coherent);
}