fw_config
	field DB_USB 0 3
		option USB_ABSENT		0
		option USB3_PS8815		1
	end
	field KB_BL 4 4
		option KB_BL_ABSENT		0
		option KB_BL_PRESENT		1
	end
	field AUDIO 5 7
		option AUDIO_UNKNOWN		0
		option MAX98373_NAU88L25B_I2S	1
	end
	field BOOT_NVME_MASK 8
		option BOOT_NVME_DISABLED		0
		option BOOT_NVME_ENABLED		1
	end
	field BOOT_EMMC_MASK 9
		option BOOT_EMMC_DISABLED		0
		option BOOT_EMMC_ENABLED		1
	end
	field FPMCU_MASK 10
		option FPMCU_ENABLED		0
		option FPMCU_DISABLED		1
	end
end
chip soc/intel/alderlake
	register "sagv" = "SaGv_Enabled"

	# As per Intel Advisory doc#723158, the change is required to prevent possible
	# display flickering issue.
	register "usb2_phy_sus_pg_disable" = "1"

	register "tcss_aux_ori" = "1"
	register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"

	register "usb2_ports[1]" = "USB2_PORT_EMPTY"		# Disable USB2_C1
	register "usb2_ports[3]" = "USB2_PORT_EMPTY"		# Disable M.2 WWAN

	register "usb3_ports[3]" = "USB3_PORT_EMPTY"		# Disable M.2 WWAN

	# FIVR configurations are disabled since the board doesn't have V1p05 and Vnn
	# bypass rails implemented.
	register "ext_fivr_settings" = "{
		.configure_ext_fivr = 1,
	}"

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| GSPI1             | Fingerprint MCU           |
	#| I2C0              | Audio                     |
	#| I2C1              | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#| I2C3              | TouchScreen               |
	#| I2C5              | Trackpad                  |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[1] = {
			.early_init = 1,
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 550,
			.fall_time_ns = 400,
			.data_hold_time_ns = 50,
		},
		.i2c[2] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[3] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 550,
			.fall_time_ns = 400,
			.data_hold_time_ns = 50,
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
		},
	}"

	device domain 0 on
		device ref tbt_pcie_rp0 off end
		device ref tbt_pcie_rp1 off end
		device ref tbt_pcie_rp2 off end
		device ref tcss_dma0 off end
		device ref tcss_dma1 off end
		device ref dtt on
			chip drivers/intel/dptf
				## sensor information
				register "options.tsr[0].desc" = ""DRAM""
				register "options.tsr[1].desc" = ""Soc""
				register "options.tsr[2].desc" = ""Charger""

				# TODO: below values are initial reference values only
				## Active Policy
				register "policies.active" = "{
					[0] = {
						.target = DPTF_CPU,
						.thresholds = {
								TEMP_PCT(85, 90),
								TEMP_PCT(75, 80),
								TEMP_PCT(68, 70),
								TEMP_PCT(62, 60),
								TEMP_PCT(55, 50),
								TEMP_PCT(50, 40),
								TEMP_PCT(40, 30),
						}
					},
					[1] = {
						.target = DPTF_TEMP_SENSOR_1,
						.thresholds = {
								TEMP_PCT(60, 90),
								TEMP_PCT(55, 80),
								TEMP_PCT(52, 70),
								TEMP_PCT(48, 60),
								TEMP_PCT(44, 50),
								TEMP_PCT(40, 40),
								TEMP_PCT(36, 30),
						}
					}
				}"

				## Passive Policy
				register "policies.passive" = "{
					[0] = DPTF_PASSIVE(CPU,         CPU,           90, 5000),
					[1] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_0, 55, 5000),
					[2] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_1, 55, 5000),
					[3] = DPTF_PASSIVE(CHARGER,     TEMP_SENSOR_2, 55, 5000),
				}"

				## Critical Policy
				register "policies.critical" = "{
					[0] = DPTF_CRITICAL(CPU,               100, SHUTDOWN),
					[1] = DPTF_CRITICAL(TEMP_SENSOR_0,      85, SHUTDOWN),
					[2] = DPTF_CRITICAL(TEMP_SENSOR_1,      85, SHUTDOWN),
					[3] = DPTF_CRITICAL(TEMP_SENSOR_2,      85, SHUTDOWN),
				}"

				register "controls.power_limits" = "{
					.pl1 = {
							.min_power = 18000,
							.max_power = 28000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 200,
						},
					.pl2 = {
							.min_power = 40000,
							.max_power = 40000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 1000,
						}
				}"

				## Charger Performance Control (Control, mA)
				register "controls.charger_perf" = "{
					[0] = { 255, 1700 },
					[1] = {  24, 1500 },
					[2] = {  16, 1000 },
					[3] = {   8,  500 }
				}"

				## Fan Performance Control (Percent, Speed, Noise, Power)
				register "controls.fan_perf" = "{
					[0] = {  90, 6700, 220, 2200, },
					[1] = {  80, 5800, 180, 1800, },
					[2] = {  70, 5000, 145, 1450, },
					[3] = {  60, 4900, 115, 1150, },
					[4] = {  50, 3838,  90,  900, },
					[5] = {  40, 2904,  55,  550, },
					[6] = {  30, 2337,  30,  300, },
					[7] = {  20, 1608,  15,  150, },
					[8] = {  10,  800,  10,  100, },
					[9] = {   0,    0,   0,   50, }
				}"

				## Fan options
				register "options.fan.fine_grained_control" = "1"
				register "options.fan.step_size" = "2"

				device generic 0 alias dptf_policy on end
			end
		end
		device ref pcie4_0 on
			# Enable CPU PCIE RP 1 using CLK 0
			register "cpu_pcie_rp[CPU_RP(1)]" = "{
				.clk_req = 0,
				.clk_src = 0,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			probe BOOT_NVME_MASK BOOT_NVME_ENABLED
		end
		device ref cnvi_wifi on
			chip drivers/wifi/generic
				register "wake" = "GPE0_PME_B0"
				device generic 0 on end
			end
		end
		device ref i2c0 on
			chip drivers/i2c/nau8825
				register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)"
				register "jkdet_enable" = "1"
				register "jkdet_pull_enable" = "0"
				register "jkdet_pull_up" = "0"
				register "jkdet_polarity" = "1"      # ActiveLow
				register "vref_impedance" = "2"      # 125kOhm
				register "micbias_voltage" = "6"     # 2.754
				register "sar_threshold_num" = "4"
				register "sar_threshold[0]" = "0x0C"
				register "sar_threshold[1]" = "0x1C"
				register "sar_threshold[2]" = "0x38"
				register "sar_threshold[3]" = "0x60"
				register "sar_hysteresis" = "1"
				register "sar_voltage" = "6"
				register "sar_compare_time" = "0"     # 500ns
				register "sar_sampling_time" = "0"    # 2us
				register "short_key_debounce" = "2"   # 100ms
				register "jack_insert_debounce" = "7" # 512ms
				register "jack_eject_debounce" = "7"  # 512ms
				device i2c 1a on
					probe AUDIO MAX98373_NAU88L25B_I2S
				end
			end
			chip drivers/i2c/max98373
				register "vmon_slot_no" = "0"
				register "imon_slot_no" = "1"
				register "uid" = "0"
				register "desc" = ""Right Speaker Amp""
				register "name" = ""MAXR""
				device i2c 31 on
					probe AUDIO MAX98373_NAU88L25B_I2S
				end
			end
			chip drivers/i2c/max98373
				register "vmon_slot_no" = "2"
				register "imon_slot_no" = "3"
				register "uid" = "1"
				register "desc" = ""Left Speaker Amp""
				register "name" = ""MAXL""
				device i2c 32 on
					probe AUDIO MAX98373_NAU88L25B_I2S
				end
			end
		end #I2C0
		device ref i2c1 on
			chip drivers/i2c/tpm
				register "hid" = ""GOOG0005""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
				device i2c 50 on end
			end
		end
		device ref i2c3 on
			chip drivers/i2c/hid
				register "generic.hid" = ""ELAN90FC""
				register "generic.desc" = ""ELAN Touchscreen""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
				register "generic.detect" = "1"
				register "generic.reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
				register "generic.reset_delay_ms" = "150"
				register "generic.reset_off_delay_ms" = "1"
				register "generic.enable_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
				register "generic.enable_delay_ms" = "6"
				register "generic.stop_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
				register "generic.stop_off_delay_ms" = "1"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x01"
				device i2c 0x10 on end
			end
		end
		device ref i2c5 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
				register "wake" = "GPE0_DW2_14"
				register "detect" = "1"
				device i2c 15 on end
			end
			chip drivers/i2c/hid
				register "generic.hid" = ""SYNA0000""
				register "generic.cid" = ""ACPI0C50""
				register "generic.desc" = ""Synaptics Touchpad""
				register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
				register "generic.wake" = "GPE0_DW2_14"
				register "generic.detect" = "1"
				register "hid_desc_reg_offset" = "0x20"
				device i2c 0x2c on end
			end
		end
		device ref pcie_rp3 on
			chip soc/intel/common/block/pcie/rtd3
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B4)"
				register "srcclk_pin" = "4"
				register "ext_pm_support" = "ACPI_PCIE_RP_EMIT_ALL"
				device generic 0 alias emmc_rtd3 on end
			end
			# Enable PCIe-to-eMMC bridge PCIE 3 using clk 4
			register "pch_pcie_rp[PCH_RP(3)]" = "{
				.clk_src = 4,
				.clk_req = 4,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			probe BOOT_EMMC_MASK BOOT_EMMC_ENABLED
		end	#PCIE3 BH799BB
		device ref pcie_rp6 off end	# PCIE6 WWAN
		device ref pcie_rp8 off end	# PCIE8 SD card
		device ref pcie_rp9 off end	# PCIE9-12 SSD
		device ref gspi1 on
			chip drivers/spi/acpi
				register "name" = ""CRFP""
				register "hid" = "ACPI_DT_NAMESPACE_HID"
				register "uid" = "1"
				register "compat_string" = ""google,cros-ec-spi""
				register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)"
				register "wake" = "GPE0_DW2_15"
				register "has_power_resource" = "1"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)"
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)"
				register "enable_delay_ms" = "3"
				device spi 0 on
					probe FPMCU_MASK FPMCU_ENABLED
				end
			end # FPMCU
		end
		device ref pch_espi on
			chip ec/google/chromeec
				use conn0 as mux_conn[0]
				use conn1 as mux_conn[1]
				device pnp 0c09.0 on end
			end
		end
		device ref pmc hidden
			chip drivers/intel/pmc_mux
				device generic 0 on
					chip drivers/intel/pmc_mux/conn
						use usb2_port1 as usb2_port
						use tcss_usb3_port1 as usb3_port
						device generic 0 alias conn0 on end
					end
					chip drivers/intel/pmc_mux/conn
						use usb2_port3 as usb2_port
						use tcss_usb3_port3 as usb3_port
						device generic 1 alias conn1 on end
					end
				end
			end
		end
		device ref tcss_xhci on
			chip drivers/usb/acpi
				device ref tcss_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
						device ref tcss_usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C1 (DB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
						register "usb_lpm_incapable" = "true"
						device ref tcss_usb3_port3 on end
					end
				end
			end
		end
		device ref xhci on
			chip drivers/usb/acpi
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
						device ref usb2_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C1 (DB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
						device ref usb2_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Camera""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port6 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A0 (DB)""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(1, 2))"
						device ref usb2_port9 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						register "reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
						device ref usb2_port10 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A0 (DB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(1, 2))"
						device ref usb3_port1 on end
					end
				end
			end
		end
		device ref hda on
			chip drivers/sof
				register "spkr_tplg" = "max98373"
				register "jack_tplg" = "nau8825"
				register "mic_tplg" = "_2ch_pdm0"
				device generic 0 on end
			end
		end
	end
end