fw_config
	field DB_SD 0 1
		option SD_ABSENT		0
		option SD_GL9750		1
	end
	field KB_BL 2 2
		option KB_BL_ABSENT		0
		option KB_BL_PRESENT		1
	end
	field AUDIO 3 5
		option AUDIO_UNKNOWN		0
		option MAX98360_ALC5682I_I2S	1
		option MAX98360_ALC5682IVS_I2S	2
	end
	field DB_LTE 6 7
		option LTE_ABSENT		0
		option LTE_USB			1
	end
	field EPS 10 10
		option PRIVACY_SCREEN_ABSENT	0
		option PRIVACY_SCREEN		1
	end
end
chip soc/intel/alderlake
	register "sagv" = "SaGv_Enabled"
	# Acoustic settings
	register "acoustic_noise_mitigation" = "1"
	register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_8"
	register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_8"
	register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1"
	register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1"

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| GSPI1             | Fingerprint MCU           |
	#| I2C0              | Audio                     |
	#| I2C1              | Touchscreen               |
	#| I2C2              |                           |
	#| I2C3              | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#| I2C5              | Trackpad                  |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[1] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[2] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[3] = {
			.early_init = 1,
			.speed = I2C_SPEED_FAST,
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
		},
	}"
	register "tcc_offset" = "3" # TCC of 97C
	register "usb2_ports[1]" = "USB2_PORT_MID(OC_SKIP)"     # Type-A MLB Port
	register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)"     # Smart Card
	register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port
	register "tcss_ports[1]" = "TCSS_PORT_EMPTY"
	device domain 0 on
		device ref igpu on
			chip drivers/gfx/generic
				register "device_count" = "1"
				register "device[0].name" = ""LCD""
				# Use ChromeOS privacy screen _HID
				register "device[0].hid" = ""GOOG0010""
				# Internal panel on the first port of the graphics chip
				register "device[0].addr" = "0x80010400"
				register "device[0].privacy.enabled" = "1"
				register "device[0].privacy.gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H21)"
				device generic 0 on
					probe EPS PRIVACY_SCREEN
				end
			 end
                end # Integrated Graphics Device
		device ref dtt on
			chip drivers/intel/dptf
				## sensor information
				register "options.tsr[0].desc" = ""DRAM""
				register "options.tsr[1].desc" = ""Soc""
				register "options.tsr[2].desc" = ""Charger""
				register "options.tsr[3].desc" = ""Regulator""
				# TODO: below values are initial reference values only
				## Passive Policy
				register "policies.passive" = "{
					[0] = DPTF_PASSIVE(CPU,         CPU,           95, 5000),
					[1] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_0, 75, 5000),
					[2] = DPTF_PASSIVE(CPU,		TEMP_SENSOR_1, 75, 5000),
					[3] = DPTF_PASSIVE(CHARGER,     TEMP_SENSOR_2, 75, 5000),
					[4] = DPTF_PASSIVE(CPU,		TEMP_SENSOR_3, 75, 5000),
				}"
				## Critical Policy
				register "policies.critical" = "{
					[0] = DPTF_CRITICAL(CPU,               105, SHUTDOWN),
					[1] = DPTF_CRITICAL(TEMP_SENSOR_0,      85, SHUTDOWN),
					[2] = DPTF_CRITICAL(TEMP_SENSOR_1,      85, SHUTDOWN),
					[3] = DPTF_CRITICAL(TEMP_SENSOR_2,	85, SHUTDOWN),
					[4] = DPTF_CRITICAL(TEMP_SENSOR_3,	85, SHUTDOWN),
				}"
				register "controls.power_limits" = "{
					.pl1 = {
							.min_power = 3000,
							.max_power = 15000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 200,
						},
					.pl2 = {
							.min_power = 55000,
							.max_power = 55000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 1000,
						}
				}"
				## Charger Performance Control (Control, mA)
				register "controls.charger_perf" = "{
					[0] = { 255, 1700 },
					[1] = {  24, 1500 },
					[2] = {  16, 1000 },
					[3] = {   8,  500 }
				}"
				device generic 0 on end
			end
		end
		device ref tbt_pcie_rp1 off end
		device ref cnvi_wifi on
			chip drivers/wifi/generic
				register "wake" = "GPE0_PME_B0"
				device generic 0 on end
			end
		end
		device ref pcie_rp6 off end
		device ref pcie_rp7 on
			# Enable PCIE eMMC bridge 7 using clk 6
			register "pch_pcie_rp[PCH_RP(7)]" = "{
				.clk_src = 6,
				.clk_req = 6,
				.flags = PCIE_RP_HOTPLUG | PCIE_RP_AER,
			}"
		end     #PCIE7 EMMC
		device ref tcss_dma0 on
			chip drivers/intel/usb4/retimer
				register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
				use tcss_usb3_port1 as dfp[0].typec_port
				device generic 0 on end
			end
		end
		device ref tcss_dma1 on
			chip drivers/intel/usb4/retimer
				register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
				use tcss_usb3_port3 as dfp[0].typec_port
				device generic 0 on end
			end
		end
		device ref pcie_rp8 on
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)"
				register "srcclk_pin" = "3"
				device generic 0 on end
			end
		end	#PCIE8 SD card
		device ref i2c0 on
			chip drivers/i2c/generic
				register "hid" = ""10EC5682""
				register "name" = ""RT58""
				register "desc" = ""Headset Codec""
				register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
				# Set the jd_src to RT5668_JD1 for jack detection
				register "property_count" = "1"
				register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
				register "property_list[0].name" = ""realtek,jd-src""
				register "property_list[0].integer" = "1"
				device i2c 1a on
					probe AUDIO MAX98360_ALC5682I_I2S
				end
			end
			chip drivers/i2c/generic
				register "hid" = ""RTL5682""
				register "name" = ""RT58""
				register "desc" = ""Headset Codec""
				register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
				# Set the jd_src to RT5668_JD1 for jack detection
				register "property_count" = "1"
				register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
				register "property_list[0].name" = ""realtek,jd-src""
				register "property_list[0].integer" = "1"
				device i2c 1a on
                                        probe AUDIO MAX98360_ALC5682IVS_I2S
				end
			end
		end #I2C0
		device ref i2c1 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0001""
				register "desc" = ""ELAN Touchscreen""
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
				register "detect" = "1"
				register "reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
				register "reset_delay_ms" = "100"
				register "reset_off_delay_ms" = "5"
				register "enable_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
				register "enable_delay_ms" = "10"
				register "enable_off_delay_ms" = "1"
				register "stop_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
				register "has_power_resource" = "1"
				device i2c 10 on end
			end
			chip drivers/i2c/hid
				register "generic.hid" = ""GTCH7503""
				register "generic.desc" = ""G2TOUCH Touchscreen""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
				register "generic.detect" = "1"
				register "generic.reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
				register "generic.reset_delay_ms" = "50"
				register "generic.enable_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
				register "generic.enable_delay_ms" = "1"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x01"
				device i2c 40 on end
			end
		end
		device ref i2c3 on
			chip drivers/i2c/tpm
				register "hid" = ""GOOG0005""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
				device i2c 50 on end
			end
		end
		device ref i2c5 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
				register "wake" = "GPE0_DW2_14"
				register "detect" = "1"
				device i2c 15 on end
			end
		end
		device ref hda on
			chip drivers/generic/max98357a
				register "hid" = ""MX98360A""
				register "sdmode_gpio" =  "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
				register "sdmode_delay" = "5"
				device generic 0 on end
			end
		end
		device ref gspi1 on
			chip drivers/spi/acpi
				register "name" = ""CRFP""
				register "hid" = "ACPI_DT_NAMESPACE_HID"
				register "uid" = "1"
				register "compat_string" = ""google,cros-ec-spi""
				register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)"
				register "wake" = "GPE0_DW2_15"
				register "has_power_resource" = "1"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)"
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)"
				register "enable_delay_ms" = "3"
				device spi 0 on end
			end # FPMCU
		end
		device ref pch_espi on
			chip ec/google/chromeec
				use conn0 as mux_conn[0]
				use conn1 as mux_conn[1]
				device pnp 0c09.0 on end
			end
		end
		device ref pmc hidden
			chip drivers/intel/pmc_mux
				device generic 0 on
					chip drivers/intel/pmc_mux/conn
						use usb2_port1 as usb2_port
						use tcss_usb3_port1 as usb3_port
						device generic 0 alias conn0 on end
					end
					chip drivers/intel/pmc_mux/conn
						use usb2_port3 as usb2_port
						use tcss_usb3_port3 as usb3_port
						device generic 1 alias conn1 on end
					end
				end
			end
		end
		device ref tcss_xhci on
			chip drivers/usb/acpi
				device ref tcss_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))"
						device ref tcss_usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C2 (DB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
						device ref tcss_usb3_port3 on end
					end
				end
			end
		end
		device ref xhci on
			chip drivers/usb/acpi
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))"
						device ref usb2_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port (MLB)""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, LEFT, ACPI_PLD_GROUP(3, 2))"
						device ref usb2_port2 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C2 (DB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
						device ref usb2_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 WWAN""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port4 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Camera""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port6 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port (DB)""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))"
						device ref usb2_port9 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						register "reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
						device ref usb2_port10 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port (DB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))"
						device ref usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port (MLB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, LEFT, ACPI_PLD_GROUP(3, 2))"
						device ref usb3_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 WWAN""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb3_port4 on end
					end
				end
			end
		end
	end
end