config SOC_INTEL_ICELAKE
	bool
	help
	  Intel Icelake support

if SOC_INTEL_ICELAKE

config CPU_SPECIFIC_OPTIONS
	def_bool y
	select ACPI_INTEL_HARDWARE_SLEEP_VALUES
	select ARCH_X86
	select BOOT_DEVICE_SUPPORTS_WRITES
	select CACHE_MRC_SETTINGS
	select SET_IA32_FC_LOCK_BIT
	select CPU_INTEL_FIRMWARE_INTERFACE_TABLE
	select CPU_SUPPORTS_PM_TIMER_EMULATION
	select DISPLAY_FSP_VERSION_INFO
	select EDK2_CPU_TIMER_LIB if PAYLOAD_EDK2
	select FSP_M_XIP
	select FSP_STATUS_GLOBAL_RESET_REQUIRED_3
	select GENERIC_GPIO_LIB
	select HAVE_FSP_GOP
	select HAVE_INTEL_FSP_REPO
	select INTEL_DESCRIPTOR_MODE_CAPABLE
	select HAVE_SMI_HANDLER
	select IDT_IN_EVERY_STAGE
	select INTEL_CAR_NEM_ENHANCED
	select INTEL_GMA_ACPI
	select INTEL_GMA_ADD_VBT if RUN_FSP_GOP
	select MP_SERVICES_PPI_V1
	select MRC_SETTINGS_PROTECT
	select PARALLEL_MP_AP_WORK
	select MICROCODE_BLOB_UNDISCLOSED
	select PLATFORM_USES_FSP2_1
	select PMC_GLOBAL_RESET_ENABLE_LOCK
	select CPU_INTEL_COMMON
	select SOC_INTEL_COMMON
	select SOC_INTEL_COMMON_ACPI_WAKE_SOURCE
	select SOC_INTEL_COMMON_BLOCK
	select SOC_INTEL_COMMON_BLOCK_ACPI
	select SOC_INTEL_COMMON_BLOCK_ACPI_CPPC
	select SOC_INTEL_COMMON_BLOCK_ACPI_LPIT
	select SOC_INTEL_COMMON_BLOCK_ACPI_GPIO
	select SOC_INTEL_COMMON_BLOCK_CAR
	select SOC_INTEL_COMMON_BLOCK_CHIP_CONFIG
	select SOC_INTEL_COMMON_BLOCK_CNVI
	select SOC_INTEL_COMMON_BLOCK_CPU
	select SOC_INTEL_COMMON_BLOCK_CPU_MPINIT
	select SOC_INTEL_COMMON_BLOCK_CPU_SMMRELOCATE
	select SOC_INTEL_COMMON_BLOCK_GSPI_VERSION_2
	select SOC_INTEL_COMMON_BLOCK_HDA
	select SOC_INTEL_COMMON_BLOCK_SA
	select SOC_INTEL_COMMON_BLOCK_SCS
	select SOC_INTEL_COMMON_BLOCK_SMM
	select SOC_INTEL_COMMON_BLOCK_SMM_IO_TRAP
	select SOC_INTEL_COMMON_BLOCK_THERMAL_PCI_DEV
	select SOC_INTEL_COMMON_FSP_RESET
	select SOC_INTEL_COMMON_PCH_CLIENT
	select SOC_INTEL_COMMON_RESET
	select SOC_INTEL_MEM_MAPPED_PM_CONFIGURATION
	select SSE2
	select SUPPORT_CPU_UCODE_IN_CBFS
	select TSC_MONOTONIC_TIMER
	select UDELAY_TSC
	select UDK_2017_BINDING
	select USE_FSP_NOTIFY_PHASE_POST_PCI_ENUM
	select USE_FSP_NOTIFY_PHASE_READY_TO_BOOT
	select USE_FSP_NOTIFY_PHASE_END_OF_FIRMWARE
	select USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI

config DISABLE_HECI1_AT_PRE_BOOT
	default y if MAINBOARD_HAS_CHROMEOS
	select HECI_DISABLE_USING_SMM

config DCACHE_RAM_BASE
	default 0xfef00000

config DCACHE_RAM_SIZE
	default 0x40000
	help
	  The size of the cache-as-ram region required during bootblock
	  and/or romstage.

config DCACHE_BSP_STACK_SIZE
	hex
	default 0x20400
	help
	  The amount of anticipated stack usage in CAR by bootblock and
	  other stages. In the case of FSP_USES_CB_STACK default value will be
	  sum of FSP-M stack requirement (128KiB) and CB romstage stack requirement (~1KiB).

config FSP_TEMP_RAM_SIZE
	hex
	default 0x10000
	help
	  The amount of anticipated heap usage in CAR by FSP.
	  Refer to Platform FSP integration guide document to know
	  the exact FSP requirement for Heap setup.

config IFD_CHIPSET
	string
	default "icl"

config IED_REGION_SIZE
	hex
	default 0x400000

config HEAP_SIZE
	hex
	default 0x8000

config MAX_ROOT_PORTS
	int
	default 16

config SMM_TSEG_SIZE
	hex
	default 0x800000

config SMM_RESERVED_SIZE
	hex
	default 0x200000

config PCR_BASE_ADDRESS
	hex
	default 0xfd000000
	help
	  This option allows you to select MMIO Base Address of sideband bus.

config ECAM_MMCONF_BASE_ADDRESS
	default 0xc0000000

config CPU_BCLK_MHZ
	int
	default 100

config SOC_INTEL_COMMON_BLOCK_GSPI_CLOCK_MHZ
	int
	default 120

config CPU_XTAL_HZ
	default 38400000

config DRIVERS_I2C_DESIGNWARE_CLOCK_MHZ
	int
	default 133

config SOC_INTEL_COMMON_BLOCK_GSPI_MAX
	int
	default 3

config SOC_INTEL_I2C_DEV_MAX
	int
	default 6

config SOC_INTEL_UART_DEV_MAX
	int
	default 3

config CONSOLE_UART_BASE_ADDRESS
	hex
	default 0xfe032000
	depends on INTEL_LPSS_UART_FOR_CONSOLE

# Clock divider parameters for 115200 baud rate
config SOC_INTEL_COMMON_LPSS_UART_CLK_M_VAL
	hex
	default 0x30

config SOC_INTEL_COMMON_LPSS_UART_CLK_N_VAL
	hex
	default 0xc35

config VBOOT
	select VBOOT_MUST_REQUEST_DISPLAY
	select VBOOT_STARTS_IN_BOOTBLOCK
	select VBOOT_VBNV_CMOS
	select VBOOT_VBNV_CMOS_BACKUP_TO_FLASH

config CBFS_SIZE
	default 0x200000

config FSP_HEADER_PATH
	default "3rdparty/fsp/IceLakeFspBinPkg/Include"

config FSP_FD_PATH
	default "3rdparty/fsp/IceLakeFspBinPkg/Fsp.fd"

config SOC_INTEL_ICELAKE_DEBUG_CONSENT
	int "Debug Consent for ICL"
	# USB DBC is more common for developers so make this default to 3 if
	# SOC_INTEL_DEBUG_CONSENT=y
	default 3 if SOC_INTEL_DEBUG_CONSENT
	default 0
	help
	  This is to control debug interface on SOC.
	  Setting non-zero value will allow to use DBC or DCI to debug SOC.
	  PlatformDebugConsent in FspmUpd.h has the details.

	  Desired platform debug types are
	  0:Disabled, 1:Enabled (DCI OOB+[DbC]), 2:Enabled (DCI OOB),
	  3:Enabled (USB3 DbC), 4:Enabled (XDP/MIPI60), 5:Enabled (USB2 DbC),
	  6:Enable (2-wire DCI OOB), 7:Manual

endif