sb/intel/i82801jx: Route all PIRQ to INT11
Interrupt 11 is not used by legacy devices and so can always be used
for PCI interrupts. Full legacy IRQ routing is complicated and hard to
get right.
Change-Id: I6c718f4b9fb91ffcc4a136120581a4fcd7ec7231
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
diff --git a/src/southbridge/intel/i82801jx/chip.h b/src/southbridge/intel/i82801jx/chip.h
index 95d0d75..533254a 100644
--- a/src/southbridge/intel/i82801jx/chip.h
+++ b/src/southbridge/intel/i82801jx/chip.h
@@ -24,19 +24,6 @@
struct southbridge_intel_i82801jx_config {
/**
- * Interrupt Routing configuration
- * If bit7 is 1, the interrupt is disabled.
- */
- uint8_t pirqa_routing;
- uint8_t pirqb_routing;
- uint8_t pirqc_routing;
- uint8_t pirqd_routing;
- uint8_t pirqe_routing;
- uint8_t pirqf_routing;
- uint8_t pirqg_routing;
- uint8_t pirqh_routing;
-
- /**
* GPI Routing configuration
*
* Only the lower two bits have a meaning:
diff --git a/src/southbridge/intel/i82801jx/lpc.c b/src/southbridge/intel/i82801jx/lpc.c
index bd50366..18025ff 100644
--- a/src/southbridge/intel/i82801jx/lpc.c
+++ b/src/southbridge/intel/i82801jx/lpc.c
@@ -94,42 +94,43 @@
static void i82801jx_pirq_init(device_t dev)
{
device_t irq_dev;
- /* Get the chip configuration */
- config_t *config = dev->chip_info;
- pci_write_config8(dev, D31F0_PIRQA_ROUT, config->pirqa_routing);
- pci_write_config8(dev, D31F0_PIRQB_ROUT, config->pirqb_routing);
- pci_write_config8(dev, D31F0_PIRQC_ROUT, config->pirqc_routing);
- pci_write_config8(dev, D31F0_PIRQD_ROUT, config->pirqd_routing);
+ /* Interrupt 11 is not used by legacy devices and so can always be used
+ * for PCI interrupts. Full legacy IRQ routing is complicated and hard
+ * to get right. Fortunately all modern OS use MSI and so it's not that
+ * big of an issue anyway. Still we have to provide a reasonable
+ * default. Using interrupt 11 for it everywhere is a working default.
+ * ACPI-aware OS can move it to any interrupt and others will just leave
+ * them at default.
+ */
+ const u8 pirq_routing = 11;
- pci_write_config8(dev, D31F0_PIRQE_ROUT, config->pirqe_routing);
- pci_write_config8(dev, D31F0_PIRQF_ROUT, config->pirqf_routing);
- pci_write_config8(dev, D31F0_PIRQG_ROUT, config->pirqg_routing);
- pci_write_config8(dev, D31F0_PIRQH_ROUT, config->pirqh_routing);
+ pci_write_config8(dev, D31F0_PIRQA_ROUT, pirq_routing);
+ pci_write_config8(dev, D31F0_PIRQB_ROUT, pirq_routing);
+ pci_write_config8(dev, D31F0_PIRQC_ROUT, pirq_routing);
+ pci_write_config8(dev, D31F0_PIRQD_ROUT, pirq_routing);
+
+ pci_write_config8(dev, D31F0_PIRQE_ROUT, pirq_routing);
+ pci_write_config8(dev, D31F0_PIRQF_ROUT, pirq_routing);
+ pci_write_config8(dev, D31F0_PIRQG_ROUT, pirq_routing);
+ pci_write_config8(dev, D31F0_PIRQH_ROUT, pirq_routing);
/* Eric Biederman once said we should let the OS do this.
* I am not so sure anymore he was right.
*/
for (irq_dev = all_devices; irq_dev; irq_dev = irq_dev->next) {
- u8 int_pin=0, int_line=0;
+ u8 int_pin = 0;
if (!irq_dev->enabled || irq_dev->path.type != DEVICE_PATH_PCI)
continue;
int_pin = pci_read_config8(irq_dev, PCI_INTERRUPT_PIN);
- switch (int_pin) {
- case 1: /* INTA# */ int_line = config->pirqa_routing; break;
- case 2: /* INTB# */ int_line = config->pirqb_routing; break;
- case 3: /* INTC# */ int_line = config->pirqc_routing; break;
- case 4: /* INTD# */ int_line = config->pirqd_routing; break;
- }
-
- if (!int_line)
+ if (int_pin == 0)
continue;
- pci_write_config8(irq_dev, PCI_INTERRUPT_LINE, int_line);
+ pci_write_config8(irq_dev, PCI_INTERRUPT_LINE, pirq_routing);
}
}