chip soc/intel/skylake

	register "panel_cfg" = "{
		.up_delay_ms		= 200,
		.down_delay_ms		=  50,
		.cycle_delay_ms		= 500,
		.backlight_on_delay_ms	=   1,
		.backlight_off_delay_ms	= 200,
		.backlight_pwm_hz	= 200,
	}"

	# Deep Sx states
	register "deep_s3_enable_ac" = "0"
	register "deep_s3_enable_dc" = "0"
	register "deep_s5_enable_ac" = "1"
	register "deep_s5_enable_dc" = "1"
	register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN | DSX_EN_WAKE_PIN"

	register "eist_enable" = "1"

	# Mapping of USB port # to device
	#+----------------+-------+-----------------------------------+
	#| Device         | Port# | Rev                               |
	#+----------------+-------+-----------------------------------+
	#| USB C          |   1   | 2/3                               |
	#| USB A Rear     |   2   | 2/3                               |
	#| USB A Front    |   3   | 2/3                               |
	#| USB A Front    |   4   | 2/3                               |
	#| USB A Rear     |   5   | 2 on base celeron, 2/3 all others |
	#| USB A Rear     |   6   | 2 on base celeron, 2/3 all others |
	#| Bluetooth      |   7   |                                   |
	#| Daughter Board |   8   |                                   |
	#+----------------+-------+-----------------------------------+

	# Bitmap for Wake Enable on USB attach/detach
	register "usb2_wake_enable_bitmap" = "USB_PORT_WAKE_ENABLE(2) |
					      USB_PORT_WAKE_ENABLE(3) |
					      USB_PORT_WAKE_ENABLE(4) |
					      USB_PORT_WAKE_ENABLE(5) |
					      USB_PORT_WAKE_ENABLE(6)"
	register "usb3_wake_enable_bitmap" = "USB_PORT_WAKE_ENABLE(2) |
					      USB_PORT_WAKE_ENABLE(3) |
					      USB_PORT_WAKE_ENABLE(4) |
					      USB_PORT_WAKE_ENABLE(5) |
					      USB_PORT_WAKE_ENABLE(6)"

	# GPE configuration
	# Note that GPE events called out in ASL code rely on this
	# route. i.e. If this route changes then the affected GPE
	# offset bits also need to be changed.
	register "gpe0_dw0" = "GPP_B"
	register "gpe0_dw1" = "GPP_D"
	register "gpe0_dw2" = "GPP_E"

	# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
	register "gen1_dec" = "0x00fc0801"
	register "gen2_dec" = "0x000c0201"
	# EC memory map range is 0x900-0x9ff
	register "gen3_dec" = "0x00fc0901"

	# Enable DPTF
	register "dptf_enable" = "1"

	# Enable S0ix
	register "s0ix_enable" = true

	# FSP Configuration
	register "SataSalpSupport" = "0"
	register "SataPortsEnable[0]" = "1"
	register "SataPortsEnable[1]" = "1"
	register "SataPortsDevSlp[1]" = "1"
	register "DspEnable" = "1"
	register "IoBufferOwnership" = "3"
	register "SkipExtGfxScan" = "1"
	register "SaGv" = "SaGv_Enabled"
	register "PmConfigSlpS3MinAssert" = "2"        # 50ms
	register "PmConfigSlpS4MinAssert" = "1"        # 1s
	register "PmConfigSlpSusMinAssert" = "1"       # 500ms
	register "PmConfigSlpAMinAssert" = "3"         # 2s
	register "SendVrMbxCmd" = "1"                  # IMVP8 workaround

	# Intersil VR c-state issue workaround
	# send VR mailbox command for IA/GT/SA rails
	register "IslVrCmd" = "2"

	# VR Settings Configuration for 4 Domains
	#+----------------+-------+-------+-------+-------+
	#| Domain/Setting |  SA   |  IA   | GTUS  |  GTS  |
	#+----------------+-------+-------+-------+-------+
	#| Psi1Threshold  | 20A   | 20A   | 20A   | 20A   |
	#| Psi2Threshold  | 4A    | 5A    | 5A    | 5A    |
	#| Psi3Threshold  | 1A    | 1A    | 1A    | 1A    |
	#| Psi3Enable     | 1     | 1     | 1     | 1     |
	#| Psi4Enable     | 1     | 1     | 1     | 1     |
	#| ImonSlope      | 0     | 0     | 0     | 0     |
	#| ImonOffset     | 0     | 0     | 0     | 0     |
	#| IccMax         | 7A    | 34A   | 35A   | 35A   |
	#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
	#| AcLoadline(ohm)| 10.3m | 2.4m  | 3.1m  | 3.1m  |
	#| DcLoadline(ohm)| 10.3m | 2.4m  | 3.1m  | 3.1m  |
	#+----------------+-------+-------+-------+-------+
	#Note: IccMax settings are moved to SoC code
	register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(4),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.voltage_limit = 1520,
		.ac_loadline = 1030,
		.dc_loadline = 1030,
	}"

	register "domain_vr_config[VR_IA_CORE]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(5),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.voltage_limit = 1520,
		.ac_loadline = 240,
		.dc_loadline = 240,
	}"

	register "domain_vr_config[VR_GT_UNSLICED]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(5),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.voltage_limit = 1520,
		.ac_loadline = 310,
		.dc_loadline = 310,
	}"

	register "domain_vr_config[VR_GT_SLICED]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(5),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.voltage_limit = 1520,
		.ac_loadline = 310,
		.dc_loadline = 310,
	}"

	# Enable Root port 3(x1) for LAN.
	register "PcieRpEnable[2]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[2]" = "1"
	# RP 3 uses SRCCLKREQ0#
	register "PcieRpClkReqNumber[2]" = "0"
	# RP 3, Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[2]" = "1"
	# RP 3, Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[2]" = "1"
	# RP 3 uses CLK SRC 0
	register "PcieRpClkSrcNumber[2]" = "0"

	# Enable Root port 4(x1) for WLAN.
	register "PcieRpEnable[3]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[3]" = "1"
	# RP 4 uses SRCCLKREQ5#
	register "PcieRpClkReqNumber[3]" = "5"
	# RP 4, Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[3]" = "1"
	# RP 4, Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[3]" = "1"
	# RP 4 uses CLK SRC 5
	register "PcieRpClkSrcNumber[3]" = "5"

	# Enable Root port 5(x4) for NVMe.
	register "PcieRpEnable[4]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[4]" = "1"
	# RP 5 uses SRCCLKREQ1#
	register "PcieRpClkReqNumber[4]" = "1"
	# RP 5, Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[4]" = "1"
	# RP 5, Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[4]" = "1"
	# RP 5 uses CLK SRC 1
	register "PcieRpClkSrcNumber[4]" = "1"

	# Enable Root port 9 for BtoB.
	register "PcieRpEnable[8]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[8]" = "1"
	# RP 9 uses SRCCLKREQ2#
	register "PcieRpClkReqNumber[8]" = "2"
	# RP 9, Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[8]" = "1"
	# RP 9, Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[8]" = "1"
	# RP 9 uses CLK SRC 2
	register "PcieRpClkSrcNumber[8]" = "2"

	# Enable Root port 11 for BtoB.
	register "PcieRpEnable[10]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[10]" = "1"
	# RP 11 uses SRCCLKREQ2#
	register "PcieRpClkReqNumber[10]" = "2"
	# RP 11, Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[10]" = "1"
	# RP 11, Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[10]" = "1"
	# RP 11 uses CLK SRC 2
	register "PcieRpClkSrcNumber[10]" = "2"

	# Enable Root port 12 for BtoB.
	register "PcieRpEnable[11]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[11]" = "1"
	# RP 12 uses SRCCLKREQ2#
	register "PcieRpClkReqNumber[11]" = "2"
	# RP 12, Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[11]" = "1"
	# RP 12, Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[11]" = "1"
	# RP 12 uses CLK SRC 2
	register "PcieRpClkSrcNumber[11]" = "2"

	register "usb2_ports[0]" = "USB2_PORT_LONG(OC0)"	# Type-C
	register "usb2_ports[1]" = "USB2_PORT_MID(OC3)"		# Type-A Rear
	register "usb2_ports[2]" = "USB2_PORT_MID(OC2)"		# Type-A Front
	register "usb2_ports[3]" = "USB2_PORT_MID(OC2)"		# Type-A Front
	register "usb2_ports[4]" = "USB2_PORT_MID(OC1)"		# Type-A Rear
	register "usb2_ports[5]" = "USB2_PORT_MID(OC1)"		# Type-A Rear
	register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)"	# Bluetooth
	register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)"     # Type-A 2.0 / Debug

	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)"	# Type-C
	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)"	# Type-A Rear
	register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)"	# Type-A Front
	register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC2)"	# Type-A Front
	register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC1)"	# Type-A Rear
	register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC1)"	# Type-A Rear

	register "i2c_voltage[0]" = "I2C_VOLTAGE_3V3"		# HDMI CEC
	register "i2c_voltage[1]" = "I2C_VOLTAGE_3V3"		# TPM
	register "i2c_voltage[2]" = "I2C_VOLTAGE_3V3"		# Debug
	register "i2c_voltage[5]" = "I2C_VOLTAGE_1V8"		# Audio

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| GSPI0             | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#|                   | before memory is up       |
	#| I2C5              | Audio                     |
	#+-------------------+---------------------------+

	register "common_soc_config" = "{
		.gspi[0] = {
			.speed_mhz = 1,
			.early_init = 1,
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 194,
				.scl_hcnt = 100,
				.sda_hold = 36,
			},
		},
	}"

	# Must leave UART0 enabled or SD/eMMC will not work as PCI
	register "SerialIoDevMode" = "{
		[PchSerialIoIndexI2C0]  = PchSerialIoPci,
		[PchSerialIoIndexI2C1]  = PchSerialIoDisabled,
		[PchSerialIoIndexI2C2]  = PchSerialIoPci,
		[PchSerialIoIndexI2C3]  = PchSerialIoDisabled,
		[PchSerialIoIndexI2C4]  = PchSerialIoDisabled,
		[PchSerialIoIndexI2C5]  = PchSerialIoPci,
		[PchSerialIoIndexSpi0]  = PchSerialIoPci,
		[PchSerialIoIndexSpi1]  = PchSerialIoDisabled,
		[PchSerialIoIndexUart0] = PchSerialIoSkipInit,
		[PchSerialIoIndexUart1] = PchSerialIoDisabled,
		[PchSerialIoIndexUart2] = PchSerialIoSkipInit,
	}"

	register "power_limits_config" = "{
		.tdp_psyspl2 = 90,
		.psys_pmax = 120,
	}"
	register "tcc_offset" = "6"     # TCC of 94C

	device domain 0 on
		device ref igpu		on  end
		device ref sa_thermal	on  end
		device ref south_xhci		on
			chip drivers/usb/acpi
				register "desc" = ""Root Hub""
				register "type" = "UPC_TYPE_HUB"
				device usb 0.0 on
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Rear""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						device usb 2.0 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Rear Left""
						register "type" = "UPC_TYPE_A"
						device usb 2.1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Rear Right""
						register "type" = "UPC_TYPE_A"
						device usb 2.4 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Rear Middle""
						register "type" = "UPC_TYPE_A"
						device usb 2.5 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						device usb 2.6 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Rear""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						device usb 3.0 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Rear Left""
						register "type" = "UPC_TYPE_USB3_A"
						device usb 3.1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Rear Right""
						register "type" = "UPC_TYPE_USB3_A"
						device usb 3.4 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Rear Middle""
						register "type" = "UPC_TYPE_USB3_A"
						device usb 3.5 on end
					end
				end
			end
		end
		device ref thermal	on  end
		device ref i2c0		on  end
		device ref i2c2		on  end
		device ref heci1	on  end
		device ref sata		on  end
		device ref uart2	on  end
		device ref i2c5		on  end
		device ref pcie_rp1	on  end
		device ref pcie_rp3	on
			# LAN, will be swapped to port 1 by FSP
			chip drivers/net
				register "customized_leds" = "0x0fa5"
				register "wake" = "GPE0_PCI_EXP"
				device pci 00.0 on end
				register "device_index" = "0"
			end
		end
		device ref pcie_rp4	on
			# WLAN
			chip drivers/wifi/generic
				register "wake" = "GPE0_PCI_EXP"
				device pci 00.0 on end
			end
		end
		device ref pcie_rp5	on end # NVMe
		device ref pcie_rp9	on
			# 2nd LAN
			chip drivers/net
				register "customized_leds" = "0x0fa5"
				register "device_index" = "1"
				device pci 00.0 on end
			end
		end
		device ref pcie_rp11	on  end
		device ref pcie_rp12	on  end
		device ref uart0	on  end
		device ref gspi0	on
			chip drivers/spi/acpi
				register "hid" = "ACPI_DT_NAMESPACE_HID"
				register "compat_string" = ""google,cr50""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E0_IRQ)"
				device spi 0 on end
			end
		end
		device ref sdxc		on  end
		device ref lpc_espi	on
			chip ec/google/chromeec
				device pnp 0c09.0 on end
			end
		end
		device ref hda		on  end
		device ref smbus	on  end
		device ref fast_spi	on  end
	end
end