sb/intel/lynxpoint/sata: Always use AHCI mode
The other two modes are not used by any mainboard, and the code seems to
be copied from older southbridges. As the code looks incorrect, drop it.
Change-Id: I374546279a85cead1aea13e0952bbfd6f643a75b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
diff --git a/src/mainboard/asrock/b85m_pro4/devicetree.cb b/src/mainboard/asrock/b85m_pro4/devicetree.cb
index d257f18..024d1f0 100644
--- a/src/mainboard/asrock/b85m_pro4/devicetree.cb
+++ b/src/mainboard/asrock/b85m_pro4/devicetree.cb
@@ -27,7 +27,6 @@
chip southbridge/intel/lynxpoint
register "gen1_dec" = "0x000c0291" # Super I/O HWM
- register "sata_ahci" = "1"
register "sata_port_map" = "0x3f"
device pci 14.0 on end # xHCI controller
diff --git a/src/mainboard/asrock/h81m-hds/devicetree.cb b/src/mainboard/asrock/h81m-hds/devicetree.cb
index 8f36896..45119f9 100644
--- a/src/mainboard/asrock/h81m-hds/devicetree.cb
+++ b/src/mainboard/asrock/h81m-hds/devicetree.cb
@@ -35,7 +35,6 @@
end
chip southbridge/intel/lynxpoint
- register "sata_ahci" = "1"
register "sata_port_map" = "0x33"
register "gen1_dec" = "0x00000295" # Super I/O HWM
diff --git a/src/mainboard/google/beltino/devicetree.cb b/src/mainboard/google/beltino/devicetree.cb
index 8fdfbd7..176fced 100644
--- a/src/mainboard/google/beltino/devicetree.cb
+++ b/src/mainboard/google/beltino/devicetree.cb
@@ -45,8 +45,6 @@
register "gpe0_en_3" = "0x00000000"
register "gpe0_en_4" = "0x00000000"
- register "ide_legacy_combined" = "0x0"
- register "sata_ahci" = "0x1"
register "sata_port_map" = "0x1"
register "sata_devslp_disable" = "0x1"
diff --git a/src/mainboard/google/slippy/devicetree.cb b/src/mainboard/google/slippy/devicetree.cb
index 200721b..a6fab83 100644
--- a/src/mainboard/google/slippy/devicetree.cb
+++ b/src/mainboard/google/slippy/devicetree.cb
@@ -52,8 +52,6 @@
register "gpe0_en_3" = "0x00000000"
register "gpe0_en_4" = "0x00000000"
- register "ide_legacy_combined" = "0x0"
- register "sata_ahci" = "0x1"
register "sata_port_map" = "0x1"
register "sio_acpi_mode" = "1"
diff --git a/src/mainboard/intel/baskingridge/devicetree.cb b/src/mainboard/intel/baskingridge/devicetree.cb
index 6345090..784c926 100644
--- a/src/mainboard/intel/baskingridge/devicetree.cb
+++ b/src/mainboard/intel/baskingridge/devicetree.cb
@@ -41,8 +41,6 @@
register "alt_gp_smi_en" = "0x0000"
register "gpe0_en_1" = "0x4000"
- register "ide_legacy_combined" = "0x0"
- register "sata_ahci" = "0x1"
register "sata_port_map" = "0x3f"
# SuperIO range is 0x700-0x73f
diff --git a/src/mainboard/lenovo/t440p/devicetree.cb b/src/mainboard/lenovo/t440p/devicetree.cb
index 8c35681..9359bb4 100644
--- a/src/mainboard/lenovo/t440p/devicetree.cb
+++ b/src/mainboard/lenovo/t440p/devicetree.cb
@@ -37,7 +37,6 @@
register "gen4_dec" = "0x000c06a1"
register "gpi13_routing" = "2"
register "gpi1_routing" = "2"
- register "sata_ahci" = "1"
# 0(HDD), 1(M.2), 5(ODD)
register "sata_port_map" = "0x23"
device pci 14.0 on end # xHCI Controller
diff --git a/src/mainboard/supermicro/x10slm-f/devicetree.cb b/src/mainboard/supermicro/x10slm-f/devicetree.cb
index ffcc56d..6d64a90 100644
--- a/src/mainboard/supermicro/x10slm-f/devicetree.cb
+++ b/src/mainboard/supermicro/x10slm-f/devicetree.cb
@@ -26,7 +26,6 @@
device pci 03.0 off end # Mini-HD audio
chip southbridge/intel/lynxpoint
- register "sata_ahci" = "1"
register "sata_port_map" = "0x3f"
register "gen1_dec" = "0x00000295" # Super I/O HWM
diff --git a/src/southbridge/intel/lynxpoint/chip.h b/src/southbridge/intel/lynxpoint/chip.h
index 40d0460..89bbb1c 100644
--- a/src/southbridge/intel/lynxpoint/chip.h
+++ b/src/southbridge/intel/lynxpoint/chip.h
@@ -38,9 +38,7 @@
uint32_t gpe0_en_4;
uint32_t alt_gp_smi_en;
- /* IDE configuration */
- uint32_t ide_legacy_combined;
- uint32_t sata_ahci;
+ /* SATA configuration */
uint8_t sata_port_map;
uint32_t sata_port0_gen3_tx;
uint32_t sata_port1_gen3_tx;
diff --git a/src/southbridge/intel/lynxpoint/sata.c b/src/southbridge/intel/lynxpoint/sata.c
index e1a2fa5..c9c7f2c 100644
--- a/src/southbridge/intel/lynxpoint/sata.c
+++ b/src/southbridge/intel/lynxpoint/sata.c
@@ -29,6 +29,9 @@
{
u32 reg32;
u16 reg16;
+
+ u32 *abar;
+
/* Get the chip configuration */
config_t *config = dev->chip_info;
@@ -44,170 +47,87 @@
/* Enable memory space decoding for ABAR */
pci_or_config16(dev, PCI_COMMAND, PCI_COMMAND_MEMORY | PCI_COMMAND_IO);
- if (config->ide_legacy_combined) {
- printk(BIOS_DEBUG, "SATA: Controller in combined mode.\n");
+ printk(BIOS_DEBUG, "SATA: Controller in AHCI mode.\n");
- /* No AHCI: clear AHCI base */
- pci_write_config32(dev, 0x24, 0);
+ /* Set Interrupt Line */
+ /* Interrupt Pin is set by D31IP.PIP */
+ pci_write_config8(dev, INTR_LN, 0x0a);
- /* And without AHCI BAR no memory decoding */
- pci_and_config16(dev, PCI_COMMAND, ~PCI_COMMAND_MEMORY);
+ /* Set timings */
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
- pci_write_config8(dev, 0x09, 0x80);
+ /* Sync DMA */
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_PSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0001);
- /* Set timings */
- pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
- IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
- pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
- IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
- IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+ /* Set IDE I/O Configuration */
+ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
+ pci_write_config32(dev, IDE_CONFIG, reg32);
- /* Sync DMA */
- pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0);
- pci_write_config16(dev, IDE_SDMA_TIM, 0x0200);
+ /* for AHCI, Port Enable is managed in memory mapped space */
+ reg16 = pci_read_config16(dev, 0x92);
+ reg16 &= ~0x3f;
+ reg16 |= 0x8000 | config->sata_port_map;
+ pci_write_config16(dev, 0x92, reg16);
+ udelay(2);
- /* Set IDE I/O Configuration */
- reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
- pci_write_config32(dev, IDE_CONFIG, reg32);
-
- /* Port enable */
- reg16 = pci_read_config16(dev, 0x92);
- reg16 &= ~0x3f;
- reg16 |= config->sata_port_map;
- pci_write_config16(dev, 0x92, reg16);
-
- /* SATA Initialization register */
- pci_write_config32(dev, 0x94, ((config->sata_port_map ^ 0x3f) << 24) | 0x183);
- } else if (config->sata_ahci) {
- u32 *abar;
-
- printk(BIOS_DEBUG, "SATA: Controller in AHCI mode.\n");
-
- /* Set Interrupt Line */
- /* Interrupt Pin is set by D31IP.PIP */
- pci_write_config8(dev, INTR_LN, 0x0a);
-
- /* Set timings */
- pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
- IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
- IDE_PPE0 | IDE_IE0 | IDE_TIME0);
- pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
- IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
-
- /* Sync DMA */
- pci_write_config16(dev, IDE_SDMA_CNT, IDE_PSDE0);
- pci_write_config16(dev, IDE_SDMA_TIM, 0x0001);
-
- /* Set IDE I/O Configuration */
- reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
- pci_write_config32(dev, IDE_CONFIG, reg32);
-
- /* for AHCI, Port Enable is managed in memory mapped space */
- reg16 = pci_read_config16(dev, 0x92);
- reg16 &= ~0x3f;
- reg16 |= 0x8000 | config->sata_port_map;
- pci_write_config16(dev, 0x92, reg16);
- udelay(2);
-
- /* Setup register 98h */
- reg32 = pci_read_config16(dev, 0x98);
- reg32 |= 1 << 19; /* BWG step 6 */
- reg32 |= 1 << 22; /* BWG step 5 */
- reg32 &= ~(0x3f << 7);
- reg32 |= 0x04 << 7; /* BWG step 7 */
- reg32 |= 1 << 20; /* BWG step 8 */
- reg32 &= ~(0x03 << 5);
- reg32 |= 1 << 5; /* BWG step 9 */
- reg32 |= 1 << 18; /* BWG step 10 */
- reg32 |= 1 << 29; /* BWG step 11 */
- if (pch_is_lp()) {
- reg32 &= ~((1 << 31) | (1 << 30));
- reg32 |= 1 << 23;
- reg32 |= 1 << 24; /* Disable listen mode (hotplug) */
- }
- pci_write_config32(dev, 0x98, reg32);
-
- /* Setup register 9Ch: Disable alternate ID and BWG step 12 */
- pci_write_config16(dev, 0x9c, 1 << 5);
-
- /* SATA Initialization register */
- reg32 = 0x183;
- reg32 |= (config->sata_port_map ^ 0x3f) << 24;
- reg32 |= (config->sata_devslp_mux & 1) << 15;
- pci_write_config32(dev, 0x94, reg32);
-
- /* Initialize AHCI memory-mapped space */
- abar = (u32 *)pci_read_config32(dev, PCI_BASE_ADDRESS_5);
- printk(BIOS_DEBUG, "ABAR: %p\n", abar);
- /* CAP (HBA Capabilities) : enable power management */
- reg32 = read32(abar + 0x00);
- reg32 |= 0x0c006000; // set PSC+SSC+SALP+SSS
- reg32 &= ~0x00020060; // clear SXS+EMS+PMS
- if (pch_is_lp())
- reg32 |= (1 << 18); // SAM: SATA AHCI MODE ONLY
- write32(abar + 0x00, reg32);
- /* PI (Ports implemented) */
- write32(abar + 0x03, config->sata_port_map);
- (void)read32(abar + 0x03); /* Read back 1 */
- (void)read32(abar + 0x03); /* Read back 2 */
- /* CAP2 (HBA Capabilities Extended)*/
- reg32 = read32(abar + 0x09);
- /* Enable DEVSLP */
- if (pch_is_lp()) {
- if (config->sata_devslp_disable)
- reg32 &= ~(1 << 3);
- else
- reg32 |= (1 << 5)|(1 << 4)|(1 << 3)|(1 << 2);
- } else {
- reg32 &= ~0x00000002;
- }
- write32(abar + 0x09, reg32);
- } else {
- printk(BIOS_DEBUG, "SATA: Controller in plain mode.\n");
-
- /* No AHCI: clear AHCI base */
- pci_write_config32(dev, 0x24, 0);
-
- /* And without AHCI BAR no memory decoding */
- pci_and_config16(dev, PCI_COMMAND, ~PCI_COMMAND_MEMORY);
-
- /*
- * Native mode capable on both primary and secondary (0xa)
- * or'ed with enabled (0x50) = 0xf
- *
- * FIXME: Does not match the code.
- */
- pci_write_config8(dev, 0x09, 0x8f);
-
- /* Set Interrupt Line */
- /* Interrupt Pin is set by D31IP.PIP */
- pci_write_config8(dev, INTR_LN, 0xff);
-
- /* Set timings */
- pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
- IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
- IDE_PPE0 | IDE_IE0 | IDE_TIME0);
- pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
- IDE_SITRE | IDE_ISP_3_CLOCKS |
- IDE_RCT_1_CLOCKS | IDE_IE0 | IDE_TIME0);
-
- /* Sync DMA */
- pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0 | IDE_PSDE0);
- pci_write_config16(dev, IDE_SDMA_TIM, 0x0201);
-
- /* Set IDE I/O Configuration */
- reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
- pci_write_config32(dev, IDE_CONFIG, reg32);
-
- /* Port enable */
- reg16 = pci_read_config16(dev, 0x92);
- reg16 &= ~0x3f;
- reg16 |= config->sata_port_map;
- pci_write_config16(dev, 0x92, reg16);
-
- /* SATA Initialization register */
- pci_write_config32(dev, 0x94, ((config->sata_port_map ^ 0x3f) << 24) | 0x183);
+ /* Setup register 98h */
+ reg32 = pci_read_config16(dev, 0x98);
+ reg32 |= 1 << 19; /* BWG step 6 */
+ reg32 |= 1 << 22; /* BWG step 5 */
+ reg32 &= ~(0x3f << 7);
+ reg32 |= 0x04 << 7; /* BWG step 7 */
+ reg32 |= 1 << 20; /* BWG step 8 */
+ reg32 &= ~(0x03 << 5);
+ reg32 |= 1 << 5; /* BWG step 9 */
+ reg32 |= 1 << 18; /* BWG step 10 */
+ reg32 |= 1 << 29; /* BWG step 11 */
+ if (pch_is_lp()) {
+ reg32 &= ~((1 << 31) | (1 << 30));
+ reg32 |= 1 << 23;
+ reg32 |= 1 << 24; /* Disable listen mode (hotplug) */
}
+ pci_write_config32(dev, 0x98, reg32);
+
+ /* Setup register 9Ch: Disable alternate ID and BWG step 12 */
+ pci_write_config16(dev, 0x9c, 1 << 5);
+
+ /* SATA Initialization register */
+ reg32 = 0x183;
+ reg32 |= (config->sata_port_map ^ 0x3f) << 24;
+ reg32 |= (config->sata_devslp_mux & 1) << 15;
+ pci_write_config32(dev, 0x94, reg32);
+
+ /* Initialize AHCI memory-mapped space */
+ abar = (u32 *)pci_read_config32(dev, PCI_BASE_ADDRESS_5);
+ printk(BIOS_DEBUG, "ABAR: %p\n", abar);
+ /* CAP (HBA Capabilities) : enable power management */
+ reg32 = read32(abar + 0x00);
+ reg32 |= 0x0c006000; // set PSC+SSC+SALP+SSS
+ reg32 &= ~0x00020060; // clear SXS+EMS+PMS
+ if (pch_is_lp())
+ reg32 |= (1 << 18); // SAM: SATA AHCI MODE ONLY
+ write32(abar + 0x00, reg32);
+ /* PI (Ports implemented) */
+ write32(abar + 0x03, config->sata_port_map);
+ (void)read32(abar + 0x03); /* Read back 1 */
+ (void)read32(abar + 0x03); /* Read back 2 */
+ /* CAP2 (HBA Capabilities Extended)*/
+ reg32 = read32(abar + 0x09);
+ /* Enable DEVSLP */
+ if (pch_is_lp()) {
+ if (config->sata_devslp_disable)
+ reg32 &= ~(1 << 3);
+ else
+ reg32 |= (1 << 5)|(1 << 4)|(1 << 3)|(1 << 2);
+ } else {
+ reg32 &= ~0x00000002;
+ }
+ write32(abar + 0x09, reg32);
/* Set Gen3 Transmitter settings if needed */
if (config->sata_port0_gen3_tx)
@@ -290,7 +210,6 @@
{
/* Get the chip configuration */
config_t *config = dev->chip_info;
- u16 map = 0;
if (!config)
return;
@@ -299,12 +218,7 @@
* Set SATA controller mode early so the resource allocator can
* properly assign IO/Memory resources for the controller.
*/
- if (config->sata_ahci)
- map = 0x0060;
-
- map |= (config->sata_port_map ^ 0x3f) << 8;
-
- pci_write_config16(dev, 0x90, map);
+ pci_write_config16(dev, 0x90, 0x0060 | (config->sata_port_map ^ 0x3f) << 8);
}
static struct device_operations sata_ops = {