mb/google/brya/var/dochi: Add memory config
Configure the rcomp, dqs and dq tables based on the schematic.
BUG=b:298337185
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=dochi emerge-brya coreboot
Change-Id: I182e287423e6f784712c5004a6fe2d12a5b36190
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
diff --git a/src/mainboard/google/brya/variants/dochi/Makefile.inc b/src/mainboard/google/brya/variants/dochi/Makefile.inc
new file mode 100644
index 0000000..c44e4f0
--- /dev/null
+++ b/src/mainboard/google/brya/variants/dochi/Makefile.inc
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+romstage-y += memory.c
diff --git a/src/mainboard/google/brya/variants/dochi/memory.c b/src/mainboard/google/brya/variants/dochi/memory.c
new file mode 100644
index 0000000..daf0695
--- /dev/null
+++ b/src/mainboard/google/brya/variants/dochi/memory.c
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+
+#include <baseboard/gpio.h>
+#include <baseboard/variants.h>
+#include <gpio.h>
+#include <soc/romstage.h>
+
+static const struct mb_cfg baseboard_memcfg = {
+ .type = MEM_TYPE_LP5X,
+
+ .rcomp = {
+ /* Baseboard uses only 100ohm Rcomp resistors */
+ .resistor = 100,
+ },
+
+ /* DQ byte map */
+ .lpx_dq_map = {
+ .ddr0 = {
+ .dq0 = { 0, 3, 2, 1, 6, 4, 5, 7 },
+ .dq1 = { 14, 12, 13, 15, 11, 8, 10, 9 },
+ },
+ .ddr1 = {
+ .dq0 = { 1, 0, 2, 3, 6, 4, 7, 5 },
+ .dq1 = { 11, 8, 10, 9, 15, 14, 13, 12 },
+ },
+ .ddr2 = {
+ .dq0 = { 6, 4, 7, 5, 3, 1, 2, 0 },
+ .dq1 = { 14, 12, 13, 15, 9, 10, 11, 8 },
+ },
+ .ddr3 = {
+ .dq0 = { 1, 2, 3, 0, 6, 4, 7, 5 },
+ .dq1 = { 13, 15, 12, 14, 8, 11, 10, 9 },
+ },
+ .ddr4 = {
+ .dq0 = { 2, 3, 0, 1, 6, 5, 7, 4 },
+ .dq1 = { 14, 15, 13, 12, 10, 8, 9, 11 },
+ },
+ .ddr5 = {
+ .dq0 = { 1, 2, 3, 0, 6, 4, 7, 5 },
+ .dq1 = { 15, 13, 12, 14, 10, 9, 8, 11 },
+ },
+ .ddr6 = {
+ .dq0 = { 2, 1, 3, 0, 7, 5, 4, 6 },
+ .dq1 = { 15, 13, 14, 12, 11, 9, 10, 8 },
+ },
+ .ddr7 = {
+ .dq0 = { 3, 1, 2, 0, 5, 4, 7, 6 },
+ .dq1 = { 14, 15, 9, 11, 13, 8, 10, 12 },
+ },
+ },
+
+ /* DQS CPU<>DRAM map */
+ .lpx_dqs_map = {
+ .ddr0 = { .dqs0 = 0, .dqs1 = 1 },
+ .ddr1 = { .dqs0 = 0, .dqs1 = 1 },
+ .ddr2 = { .dqs0 = 0, .dqs1 = 1 },
+ .ddr3 = { .dqs0 = 0, .dqs1 = 1 },
+ .ddr4 = { .dqs0 = 0, .dqs1 = 1 },
+ .ddr5 = { .dqs0 = 0, .dqs1 = 1 },
+ .ddr6 = { .dqs0 = 0, .dqs1 = 1 },
+ .ddr7 = { .dqs0 = 0, .dqs1 = 1 },
+ },
+
+ .lp5x_config = {
+ .ccc_config = 0xff,
+ },
+
+ .ect = 1, /* Early Command Training */
+
+ .UserBd = BOARD_TYPE_ULT_ULX,
+};
+
+const struct mb_cfg *variant_memory_params(void)
+{
+ return &baseboard_memcfg;
+}
+
+int variant_memory_sku(void)
+{
+ /*
+ * Memory configuration board straps
+ * GPIO_MEM_CONFIG_0 GPP_E11
+ * GPIO_MEM_CONFIG_1 GPP_E2
+ * GPIO_MEM_CONFIG_2 GPP_E1
+ * GPIO_MEM_CONFIG_3 GPP_E12
+ */
+ gpio_t spd_gpios[] = {
+ GPP_E11,
+ GPP_E2,
+ GPP_E1,
+ GPP_E12,
+ };
+
+ return gpio_base2_value(spd_gpios, ARRAY_SIZE(spd_gpios));
+}
+
+bool variant_is_half_populated(void)
+{
+ /*
+ * Ideally half_populated is used in platforms with multiple channels to
+ * enable only one half of the channel. Alder Lake N has single channel,
+ * and it would require for new structures to be defined in meminit block
+ * driver for LPx memory configurations. In order to avoid adding new
+ * structures, set half_populated to true. This has the same effect as
+ * having single channel with 64-bit width.
+ */
+ /* GPIO_MEM_CH_SEL GPP_E13 */
+ return gpio_get(GPP_E13);
+}
+
+void variant_get_spd_info(struct mem_spd *spd_info)
+{
+ spd_info->topo = MEM_TOPO_MEMORY_DOWN;
+ spd_info->cbfs_index = variant_memory_sku();
+}