Revert "mb/aopen/dxplplusu: Remove board"
This reverts commit eb76a455cd39ec59b7f2ba28baeec9538befd59e
and applies minor fixes to make it build again.
PARALLEL_MP was working prior to board removal and no
relevant SMI handlers were implemented. So NO_SMM choice
is now selected.
Change-Id: Ia1cd02278240d1b5d006fb2a7730d3d86390f85b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
diff --git a/src/southbridge/intel/i82801dx/lpc.c b/src/southbridge/intel/i82801dx/lpc.c
new file mode 100644
index 0000000..1de3766
--- /dev/null
+++ b/src/southbridge/intel/i82801dx/lpc.c
@@ -0,0 +1,328 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <arch/hpet.h>
+#include <arch/io.h>
+#include <arch/ioapic.h>
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <option.h>
+#include <pc80/mc146818rtc.h>
+#include <pc80/isa-dma.h>
+#include <pc80/i8259.h>
+#include "chip.h"
+#include "i82801dx.h"
+
+#define NMI_OFF 0
+
+typedef struct southbridge_intel_i82801dx_config config_t;
+
+/**
+ * Enable ACPI I/O range.
+ *
+ * @param dev PCI device with ACPI and PM BAR's
+ */
+static void i82801dx_enable_acpi(struct device *dev)
+{
+ /* Set ACPI base address (I/O space). */
+ pci_write_config32(dev, PMBASE, (PMBASE_ADDR | 1));
+
+ /* Enable ACPI I/O range decode and ACPI power management. */
+ pci_write_config8(dev, ACPI_CNTL, ACPI_EN);
+}
+
+/**
+ * Set miscellaneous static southbridge features.
+ *
+ * @param dev PCI device with I/O APIC control registers
+ */
+static void i82801dx_enable_ioapic(struct device *dev)
+{
+ u32 reg32;
+
+ reg32 = pci_read_config32(dev, GEN_CNTL);
+ reg32 |= (1 << 13); /* Coprocessor error enable (COPR_ERR_EN) */
+ reg32 |= (3 << 7); /* IOAPIC enable (APIC_EN) */
+ reg32 |= (1 << 2); /* DMA collection buffer enable (DCB_EN) */
+ reg32 |= (1 << 1); /* Delayed transaction enable (DTE) */
+ pci_write_config32(dev, GEN_CNTL, reg32);
+ printk(BIOS_DEBUG, "IOAPIC Southbridge enabled %x\n", reg32);
+
+ setup_ioapic(VIO_APIC_VADDR, 0x02);
+
+ ioapic_set_boot_config(VIO_APIC_VADDR, true);
+}
+
+static void i82801dx_enable_serial_irqs(struct device *dev)
+{
+ /* Set packet length and toggle silent mode bit. */
+ pci_write_config8(dev, SERIRQ_CNTL,
+ (1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0));
+ pci_write_config8(dev, SERIRQ_CNTL,
+ (1 << 7) | (0 << 6) | ((21 - 17) << 2) | (0 << 0));
+}
+
+static void i82801dx_pirq_init(struct device *dev)
+{
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+
+ pci_write_config8(dev, PIRQA_ROUT, config->pirqa_routing);
+ pci_write_config8(dev, PIRQB_ROUT, config->pirqb_routing);
+ pci_write_config8(dev, PIRQC_ROUT, config->pirqc_routing);
+ pci_write_config8(dev, PIRQD_ROUT, config->pirqd_routing);
+ pci_write_config8(dev, PIRQE_ROUT, config->pirqe_routing);
+ pci_write_config8(dev, PIRQF_ROUT, config->pirqf_routing);
+ pci_write_config8(dev, PIRQG_ROUT, config->pirqg_routing);
+ pci_write_config8(dev, PIRQH_ROUT, config->pirqh_routing);
+}
+
+static void i82801dx_power_options(struct device *dev)
+{
+ u8 reg8;
+ u16 reg16, pmbase;
+ u32 reg32;
+ const char *state;
+
+ /* Which state do we want to goto after g3 (power restored)?
+ * 0 == S0 Full On
+ * 1 == S5 Soft Off
+ *
+ * If the option is not existent (Laptops), use MAINBOARD_POWER_ON.
+ */
+ const unsigned int pwr_on = get_uint_option("power_on_after_fail", MAINBOARD_POWER_ON);
+
+ reg8 = pci_read_config8(dev, GEN_PMCON_3);
+ reg8 &= 0xfe;
+ switch (pwr_on) {
+ case MAINBOARD_POWER_OFF:
+ reg8 |= 1;
+ state = "off";
+ break;
+ case MAINBOARD_POWER_ON:
+ reg8 &= ~1;
+ state = "on";
+ break;
+ case MAINBOARD_POWER_KEEP:
+ reg8 &= ~1;
+ state = "state keep";
+ break;
+ default:
+ state = "undefined";
+ }
+
+ reg8 &= ~(1 << 3); /* minimum assertion is 1 to 2 RTCCLK */
+
+ pci_write_config8(dev, GEN_PMCON_3, reg8);
+ printk(BIOS_INFO, "Set power %s after power failure.\n", state);
+
+ /* Set up NMI on errors. */
+ reg8 = inb(0x61);
+ reg8 &= 0x0f; /* Higher Nibble must be 0 */
+ reg8 &= ~(1 << 3); /* IOCHK# NMI Enable */
+ // reg8 &= ~(1 << 2); /* PCI SERR# Enable */
+ reg8 |= (1 << 2); /* PCI SERR# Disable for now */
+ outb(reg8, 0x61);
+
+ reg8 = inb(0x70);
+ const unsigned int nmi_option = get_uint_option("nmi", NMI_OFF);
+ if (nmi_option) {
+ printk(BIOS_INFO, "NMI sources enabled.\n");
+ reg8 &= ~(1 << 7); /* Set NMI. */
+ } else {
+ printk(BIOS_INFO, "NMI sources disabled.\n");
+ reg8 |= (1 << 7); /* Disable NMI. */
+ }
+ outb(reg8, 0x70);
+
+ /* Set SMI# rate down and enable CPU_SLP# */
+ reg16 = pci_read_config16(dev, GEN_PMCON_1);
+ reg16 &= ~(3 << 0); // SMI# rate 1 minute
+ reg16 |= (1 << 5); // CPUSLP_EN Desktop only
+ pci_write_config16(dev, GEN_PMCON_1, reg16);
+
+ pmbase = pci_read_config16(dev, 0x40) & 0xfffe;
+
+ /* Set up power management block and determine sleep mode */
+ reg32 = inl(pmbase + 0x04); // PM1_CNT
+
+ reg32 &= ~(7 << 10); // SLP_TYP
+ reg32 |= (1 << 0); // SCI_EN
+ outl(reg32, pmbase + 0x04);
+}
+
+static void gpio_init(struct device *dev)
+{
+ /* This should be done in romstage.c already */
+ pci_write_config32(dev, GPIO_BASE, (GPIOBASE_ADDR | 1));
+ pci_write_config8(dev, GPIO_CNTL, 0x10);
+}
+
+static void i82801dx_rtc_init(struct device *dev)
+{
+ u8 reg8;
+ u32 reg32;
+ int rtc_failed;
+
+ reg8 = pci_read_config8(dev, GEN_PMCON_3);
+ rtc_failed = reg8 & RTC_BATTERY_DEAD;
+ if (rtc_failed) {
+ reg8 &= ~(1 << 1); /* Preserve the power fail state. */
+ pci_write_config8(dev, GEN_PMCON_3, reg8);
+ }
+ reg32 = pci_read_config32(dev, GEN_STS);
+ rtc_failed |= reg32 & (1 << 2);
+ cmos_init(rtc_failed);
+
+ /* Enable access to the upper 128 byte bank of CMOS RAM. */
+ pci_write_config8(dev, RTC_CONF, 0x04);
+}
+
+static void i82801dx_lpc_route_dma(struct device *dev, u8 mask)
+{
+ u16 reg16;
+ int i;
+
+ reg16 = pci_read_config16(dev, PCI_DMA_CFG);
+ reg16 &= 0x300;
+ for (i = 0; i < 8; i++) {
+ if (i == 4)
+ continue;
+ reg16 |= ((mask & (1 << i)) ? 3 : 1) << (i * 2);
+ }
+ pci_write_config16(dev, PCI_DMA_CFG, reg16);
+}
+
+static void i82801dx_lpc_decode_en(struct device *dev)
+{
+ /* Decode 0x3F8-0x3FF (COM1) for COMA port, 0x2F8-0x2FF (COM2) for COMB.
+ * LPT decode defaults to 0x378-0x37F and 0x778-0x77F.
+ * Floppy decode defaults to 0x3F0-0x3F5, 0x3F7.
+ * We also need to set the value for LPC I/F Enables Register.
+ */
+ pci_write_config8(dev, COM_DEC, 0x10);
+ pci_write_config16(dev, LPC_EN, 0x300F);
+}
+
+/* ICH4 does not mention HPET in the docs, but
+ * all ICH3 and ICH4 do have HPETs built in.
+ */
+static void enable_hpet(struct device *dev)
+{
+ u32 reg32, hpet, val;
+
+ /* Set HPET base address and enable it */
+ printk(BIOS_DEBUG, "Enabling HPET at 0x%x\n", HPET_BASE_ADDRESS);
+ reg32 = pci_read_config32(dev, GEN_CNTL);
+ /*
+ * Bit 17 is HPET enable bit.
+ * Bit 16:15 control the HPET base address.
+ */
+ reg32 &= ~(3 << 15); /* Clear it */
+
+ hpet = HPET_BASE_ADDRESS >> 12;
+ hpet &= 0x3;
+
+ reg32 |= (hpet << 15);
+ reg32 |= (1 << 17); /* Enable HPET. */
+ pci_write_config32(dev, GEN_CNTL, reg32);
+
+ /* Check to see whether it took */
+ reg32 = pci_read_config32(dev, GEN_CNTL);
+ val = reg32 >> 15;
+ val &= 0x7;
+
+ if ((val & 0x4) && (hpet == (val & 0x3))) {
+ printk(BIOS_INFO, "HPET enabled at 0x%x\n", HPET_BASE_ADDRESS);
+ } else {
+ printk(BIOS_WARNING, "HPET was not enabled correctly\n");
+ reg32 &= ~(1 << 17); /* Clear Enable */
+ pci_write_config32(dev, GEN_CNTL, reg32);
+ }
+}
+
+static void lpc_init(struct device *dev)
+{
+ i82801dx_enable_acpi(dev);
+ /* IO APIC initialization. */
+ i82801dx_enable_ioapic(dev);
+
+ i82801dx_enable_serial_irqs(dev);
+
+ /* Setup the PIRQ. */
+ i82801dx_pirq_init(dev);
+
+ /* Setup power options. */
+ i82801dx_power_options(dev);
+
+ /* Set the state of the GPIO lines. */
+ gpio_init(dev);
+
+ /* Initialize the real time clock. */
+ i82801dx_rtc_init(dev);
+
+ /* Route DMA. */
+ i82801dx_lpc_route_dma(dev, 0xff);
+
+ /* Initialize ISA DMA. */
+ isa_dma_init();
+
+ /* Setup decode ports and LPC I/F enables. */
+ i82801dx_lpc_decode_en(dev);
+
+ /* Initialize the High Precision Event Timers */
+ enable_hpet(dev);
+
+ setup_i8259();
+}
+
+static void i82801dx_lpc_read_resources(struct device *dev)
+{
+ struct resource *res;
+
+ /* Get the normal PCI resources of this device. */
+ pci_dev_read_resources(dev);
+
+ /* Add an extra subtractive resource for both memory and I/O. */
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0));
+ res->base = 0;
+ res->size = 0x1000;
+ res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0));
+ res->base = 0xff800000;
+ res->size = 0x00800000; /* 8 MB for flash */
+ res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+
+ res = new_resource(dev, 3); /* IOAPIC */
+ res->base = IO_APIC_ADDR;
+ res->size = 0x00001000;
+ res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+}
+
+static struct device_operations lpc_ops = {
+ .read_resources = i82801dx_lpc_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = lpc_init,
+ .scan_bus = scan_static_bus,
+ .enable = i82801dx_enable,
+};
+
+/* 82801DB/DBL */
+static const struct pci_driver lpc_driver_db __pci_driver = {
+ .ops = &lpc_ops,
+ .vendor = PCI_VID_INTEL,
+ .device = PCI_DID_INTEL_82801DB_LPC,
+};
+
+/* 82801DBM */
+static const struct pci_driver lpc_driver_dbm __pci_driver = {
+ .ops = &lpc_ops,
+ .vendor = PCI_VID_INTEL,
+ .device = PCI_DID_INTEL_82801DBM_LPC,
+};