/** @file

Copyright (c) 2022, Intel Corporation. All rights reserved.<BR>

Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this
  list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
  list of conditions and the following disclaimer in the documentation and/or
  other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
  be used to endorse or promote products derived from this software without
  specific prior written permission.

  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
  THE POSSIBILITY OF SUCH DAMAGE.

  This file is automatically generated. Please do NOT modify !!!

**/

#ifndef __FSPMUPD_H__
#define __FSPMUPD_H__

#include <FspUpd.h>

#pragma pack(1)


#include <MemInfoHob.h>

///
/// The ChipsetInit Info structure provides the information of ME ChipsetInit CRC and BIOS ChipsetInit CRC.
///
typedef struct {
  UINT8             Revision;         ///< Chipset Init Info Revision
  UINT8             Rsvd[3];          ///< Reserved
  UINT16            MeChipInitCrc;    ///< 16 bit CRC value of MeChipInit Table
  UINT16            BiosChipInitCrc;  ///< 16 bit CRC value of PchChipInit Table
} CHIPSET_INIT_INFO;


/** Fsp M Configuration
**/
typedef struct {

/** Offset 0x0040 - Platform Reserved Memory Size
  The minimum platform memory size required to pass control into DXE
**/
  UINT64                      PlatformMemorySize;

/** Offset 0x0048 - SPD Data Length
  Length of SPD Data
  0x100:256 Bytes, 0x200:512 Bytes, 0x400:1024 Bytes
**/
  UINT16                      MemorySpdDataLen;

/** Offset 0x004A - Enable above 4GB MMIO resource support
  Enable/disable above 4GB MMIO resource support
  $EN_DIS
**/
  UINT8                       EnableAbove4GBMmio;

/** Offset 0x004B - Reserved
**/
  UINT8                       Reserved0;

/** Offset 0x004C - Memory SPD Pointer Controller 0 Channel 0 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr000;

/** Offset 0x0050 - Memory SPD Pointer Controller 0 Channel 0 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr001;

/** Offset 0x0054 - Memory SPD Pointer Controller 0 Channel 1 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr010;

/** Offset 0x0058 - Memory SPD Pointer Controller 0 Channel 1 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr011;

/** Offset 0x005C - Memory SPD Pointer Controller 0 Channel 2 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr020;

/** Offset 0x0060 - Memory SPD Pointer Controller 0 Channel 2 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr021;

/** Offset 0x0064 - Memory SPD Pointer Controller 0 Channel 3 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr030;

/** Offset 0x0068 - Memory SPD Pointer Controller 0 Channel 3 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr031;

/** Offset 0x006C - Memory SPD Pointer Controller 1 Channel 0 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr100;

/** Offset 0x0070 - Memory SPD Pointer Controller 1 Channel 0 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr101;

/** Offset 0x0074 - Memory SPD Pointer Controller 1 Channel 1 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr110;

/** Offset 0x0078 - Memory SPD Pointer Controller 1 Channel 1 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr111;

/** Offset 0x007C - Memory SPD Pointer Controller 1 Channel 2 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr120;

/** Offset 0x0080 - Memory SPD Pointer Controller 1 Channel 2 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr121;

/** Offset 0x0084 - Memory SPD Pointer Controller 1 Channel 3 Dimm 0
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr130;

/** Offset 0x0088 - Memory SPD Pointer Controller 1 Channel 3 Dimm 1
  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
**/
  UINT32                      MemorySpdPtr131;

/** Offset 0x008C - RcompResistor settings
  Indicates  RcompResistor settings: Board-dependent
**/
  UINT16                      RcompResistor;

/** Offset 0x008E - RcompTarget settings
  RcompTarget settings: board-dependent
**/
  UINT16                      RcompTarget[5];

/** Offset 0x0098 - Dqs Map CPU to DRAM MC 0 CH 0
  Set Dqs mapping relationship between CPU and DRAM, Channel 0: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc0Ch0[2];

/** Offset 0x009A - Dqs Map CPU to DRAM MC 0 CH 1
  Set Dqs mapping relationship between CPU and DRAM, Channel 1: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc0Ch1[2];

/** Offset 0x009C - Dqs Map CPU to DRAM MC 0 CH 2
  Set Dqs mapping relationship between CPU and DRAM, Channel 2: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc0Ch2[2];

/** Offset 0x009E - Dqs Map CPU to DRAM MC 0 CH 3
  Set Dqs mapping relationship between CPU and DRAM, Channel 3: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc0Ch3[2];

/** Offset 0x00A0 - Dqs Map CPU to DRAM MC 1 CH 0
  Set Dqs mapping relationship between CPU and DRAM, Channel 0: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc1Ch0[2];

/** Offset 0x00A2 - Dqs Map CPU to DRAM MC 1 CH 1
  Set Dqs mapping relationship between CPU and DRAM, Channel 1: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc1Ch1[2];

/** Offset 0x00A4 - Dqs Map CPU to DRAM MC 1 CH 2
  Set Dqs mapping relationship between CPU and DRAM, Channel 2: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc1Ch2[2];

/** Offset 0x00A6 - Dqs Map CPU to DRAM MC 1 CH 3
  Set Dqs mapping relationship between CPU and DRAM, Channel 3: board-dependent
**/
  UINT8                       DqsMapCpu2DramMc1Ch3[2];

/** Offset 0x00A8 - Dq Map CPU to DRAM MC 0 CH 0
  Set Dq mapping relationship between CPU and DRAM, Channel 0: board-dependent
**/
  UINT8                       DqMapCpu2DramMc0Ch0[16];

/** Offset 0x00B8 - Dq Map CPU to DRAM MC 0 CH 1
  Set Dq mapping relationship between CPU and DRAM, Channel 1: board-dependent
**/
  UINT8                       DqMapCpu2DramMc0Ch1[16];

/** Offset 0x00C8 - Dq Map CPU to DRAM MC 0 CH 2
  Set Dq mapping relationship between CPU and DRAM, Channel 2: board-dependent
**/
  UINT8                       DqMapCpu2DramMc0Ch2[16];

/** Offset 0x00D8 - Dq Map CPU to DRAM MC 0 CH 3
  Set Dq mapping relationship between CPU and DRAM, Channel 3: board-dependent
**/
  UINT8                       DqMapCpu2DramMc0Ch3[16];

/** Offset 0x00E8 - Dq Map CPU to DRAM MC 1 CH 0
  Set Dq mapping relationship between CPU and DRAM, Channel 0: board-dependent
**/
  UINT8                       DqMapCpu2DramMc1Ch0[16];

/** Offset 0x00F8 - Dq Map CPU to DRAM MC 1 CH 1
  Set Dq mapping relationship between CPU and DRAM, Channel 1: board-dependent
**/
  UINT8                       DqMapCpu2DramMc1Ch1[16];

/** Offset 0x0108 - Dq Map CPU to DRAM MC 1 CH 2
  Set Dq mapping relationship between CPU and DRAM, Channel 2: board-dependent
**/
  UINT8                       DqMapCpu2DramMc1Ch2[16];

/** Offset 0x0118 - Dq Map CPU to DRAM MC 1 CH 3
  Set Dq mapping relationship between CPU and DRAM, Channel 3: board-dependent
**/
  UINT8                       DqMapCpu2DramMc1Ch3[16];

/** Offset 0x0128 - Dqs Pins Interleaved Setting
  Indicates DqPinsInterleaved setting: board-dependent
  $EN_DIS
**/
  UINT8                       DqPinsInterleaved;

/** Offset 0x0129 - Smram Mask
  The SMM Regions AB-SEG and/or H-SEG reserved
  0: Neither, 1:AB-SEG, 2:H-SEG, 3: Both
**/
  UINT8                       SmramMask;

/** Offset 0x012A - MRC Fast Boot
  Enables/Disable the MRC fast path thru the MRC
  $EN_DIS
**/
  UINT8                       MrcFastBoot;

/** Offset 0x012B - Rank Margin Tool per Task
  This option enables the user to execute Rank Margin Tool per major training step
  in the MRC.
  $EN_DIS
**/
  UINT8                       RmtPerTask;

/** Offset 0x012C - Training Trace
  This option enables the trained state tracing feature in MRC.  This feature will
  print out the key training parameters state across major training steps.
  $EN_DIS
**/
  UINT8                       TrainTrace;

/** Offset 0x012D - Reserved
**/
  UINT8                       Reserved1[3];

/** Offset 0x0130 - Tseg Size
  Size of SMRAM memory reserved. 0x400000 for Release build and 0x1000000 for Debug build
  0x0400000:4MB, 0x01000000:16MB
**/
  UINT32                      TsegSize;

/** Offset 0x0134 - MMIO Size
  Size of MMIO space reserved for devices. 0(Default)=Auto, non-Zero=size in MB
**/
  UINT16                      MmioSize;

/** Offset 0x0136 - Probeless Trace
  Probeless Trace: 0=Disabled, 1=Enable. Enabling Probeless Trace will reserve 128MB.
  This also requires IED to be enabled.
  $EN_DIS
**/
  UINT8                       ProbelessTrace;

/** Offset 0x0137 - Enable SMBus
  Enable/disable SMBus controller.
  $EN_DIS
**/
  UINT8                       SmbusEnable;

/** Offset 0x0138 - Spd Address Tabl
  Specify SPD Address table for CH0D0/CH0D1/CH1D0&CH1D1. MemorySpdPtr will be used
  if SPD Address is 00
**/
  UINT8                       SpdAddressTable[16];

/** Offset 0x0148 - Platform Debug Consent
  Enabled Trace active: TraceHub is enabled and trace is active, blocks s0ix.\n
  \n
  Enabled Trace ready: TraceHub is enabled and allowed S0ix.\n
  \n
  Enabled Trace power off: TraceHub is powergated, provide setting close to functional
  low power state\n
  \n
  Manual: user needs to configure Advanced Debug Settings manually, aimed at advanced users
  0:Disabled, 2:Enabled Trace Active, 4:Enabled Trace Ready, 6:Enable Trace Power-Off, 7:Manual
**/
  UINT8                       PlatformDebugOption;

/** Offset 0x0149 - DCI Enable
  Determine if to enable DCI debug from host
  $EN_DIS
**/
  UINT8                       DciEn;

/** Offset 0x014A - Reserved
**/
  UINT8                       Reserved2;

/** Offset 0x014B - DCI DbC Mode
  Disabled: Clear both USB2/3DBCEN; USB2: set USB2DBCEN; USB3: set USB3DBCEN; Both:
  Set both USB2/3DBCEN; No Change: Comply with HW value
  0:Disabled, 1:USB2 DbC, 2:USB3 DbC, 3:Both, 4:No Change
**/
  UINT8                       DciDbcMode;

/** Offset 0x014C - USB3 Type-C UFP2DFP Kernel/Platform Debug Support
  This BIOS option enables kernel and platform debug for USB3 interface over a UFP
  Type-C receptacle, select 'No Change' will do nothing to UFP2DFP setting.
  0:Disabled, 1:Enabled, 2:No Change
**/
  UINT8                       DciUsb3TypecUfpDbg;

/** Offset 0x014D - Reserved
**/
  UINT8                       Reserved3[6];

/** Offset 0x0153 - PCH Trace Hub Mode
  Enable/Disable PCH TraceHub
  $EN_DIS
**/
  UINT8                       PchTraceHubMode;

/** Offset 0x0154 - PCH Trace Hub Memory Region 0 buffer Size
  Select size of memory region 0 buffer. Memory allocated by BIOS only applies to
  ITH tool running on the host. For ITH tool running on the target, choose None/OS,
  memory shall be allocated by tool. User should be cautious to choose the amount
  of memory. If chosen size is larger than half of system memory, setup will automatically
  rollback to default value.
  0x00:1MB, 0x03:8MB, 0x06:64MB, 0x07:128MB, 0x08:256MB, 0x09:512MB, 0x0A:1GB, 0x0B:2GB,
  0x0C:4GB, 0x0D:8GB, 0x0E:0MB
**/
  UINT16                      PchTraceHubMemReg0Size;

/** Offset 0x0156 - PCH Trace Hub Memory Region 1 buffer Size
  Select size of memory region 1 buffer. Memory allocated by BIOS only applies to
  ITH tool running on the host. For ITH tool running on the target, choose None/OS,
  memory shall be allocated by tool. User should be cautious to choose the amount
  of memory. If chosen size is larger than half of system memory, setup will automatically
  rollback to default value.
  0x00:1MB, 0x03:8MB, 0x06:64MB, 0x07:128MB, 0x08:256MB, 0x09:512MB, 0x0A:1GB, 0x0B:2GB,
  0x0C:4GB, 0x0D:8GB, 0x0E:0MB
**/
  UINT16                      PchTraceHubMemReg1Size;

/** Offset 0x0158 - Reserved
**/
  UINT8                       Reserved4[4];

/** Offset 0x015C - HD Audio DMIC Link Clock Select
  Determines DMIC<N> Clock Source. 0: Both, 1: ClkA, 2: ClkB
  0: Both, 1: ClkA, 2: ClkB
**/
  UINT8                       PchHdaAudioLinkDmicClockSelect[2];

/** Offset 0x015E - State of X2APIC_OPT_OUT bit in the DMAR table
  0=Disable/Clear, 1=Enable/Set
  $EN_DIS
**/
  UINT8                       X2ApicOptOut;

/** Offset 0x015F - State of DMA_CONTROL_GUARANTEE bit in the DMAR table
  0=Disable/Clear, 1=Enable/Set
  $EN_DIS
**/
  UINT8                       DmaControlGuarantee;

/** Offset 0x0160 - Base addresses for VT-d function MMIO access
  Base addresses for VT-d MMIO access per VT-d engine
**/
  UINT32                      VtdBaseAddress[9];

/** Offset 0x0184 - Disable VT-d
  0=Enable/FALSE(VT-d enabled), 1=Disable/TRUE (VT-d disabled)
  $EN_DIS
**/
  UINT8                       VtdDisable;

/** Offset 0x0185 - Vtd Programming for Igd
  1=Enable/TRUE (Igd VT-d Bar programming enabled), 0=Disable/FLASE (Igd VT-d Bar
  programming disabled)
  $EN_DIS
**/
  UINT8                       VtdIgdEnable;

/** Offset 0x0186 - Vtd Programming for Iop
  1=Enable/TRUE (Iop VT-d Bar programming enabled), 0=Disable/FLASE (Iop VT-d Bar
  programming disabled)
  $EN_DIS
**/
  UINT8                       VtdIopEnable;

/** Offset 0x0187 - Internal Graphics Pre-allocated Memory
  Size of memory preallocated for internal graphics.
  0x00:0MB, 0x01:32MB, 0x02:64MB, 0x03:96MB, 0x04:128MB, 0xF0:4MB, 0xF1:8MB, 0xF2:12MB,
  0xF3:16MB, 0xF4:20MB, 0xF5:24MB, 0xF6:28MB, 0xF7:32MB, 0xF8:36MB, 0xF9:40MB, 0xFA:44MB,
  0xFB:48MB, 0xFC:52MB, 0xFD:56MB, 0xFE:60MB
**/
  UINT8                       IgdDvmt50PreAlloc;

/** Offset 0x0188 - Internal Graphics
  Enable/disable internal graphics.
  $EN_DIS
**/
  UINT8                       InternalGfx;

/** Offset 0x0189 - Board Type
  MrcBoardType, Options are 0=Mobile/Mobile Halo, 1=Desktop/DT Halo, 5=ULT/ULX/Mobile
  Halo, 7=UP Server
  0:Mobile/Mobile Halo, 1:Desktop/DT Halo, 5:ULT/ULX/Mobile Halo, 7:UP Server
**/
  UINT8                       UserBd;

/** Offset 0x018A - Reserved
**/
  UINT8                       Reserved5[2];

/** Offset 0x018C - DDR Frequency Limit
  Maximum Memory Frequency Selections in Mhz. Options are 1067, 1333, 1600, 1867,
  2133, 2400, 2667, 2933 and 0 for Auto.
  1067:1067, 1333:1333, 1600:1600, 1867:1867, 2133:2133, 2400:2400, 2667:2667, 2933:2933, 0:Auto
**/
  UINT16                      DdrFreqLimit;

/** Offset 0x018E - SAGV
  System Agent dynamic frequency support.
  0:Disabled, 1:Enabled
**/
  UINT8                       SaGv;

/** Offset 0x018F - Reserved
**/
  UINT8                       Reserved6;

/** Offset 0x0190 - Memory Test on Warm Boot
  Run Base Memory Test on Warm Boot
  0:Disable, 1:Enable
**/
  UINT8                       MemTestOnWarmBoot;

/** Offset 0x0191 - DDR Speed Control
  DDR Frequency and Gear control for all SAGV points.
  0:Auto, 1:Manual
**/
  UINT8                       DdrSpeedControl;

/** Offset 0x0192 - Controller 0 Channel 0 DIMM Control
  Enable / Disable DIMMs on Controller 0 Channel 0
  $EN_DIS
**/
  UINT8                       DisableMc0Ch0;

/** Offset 0x0193 - Controller 0 Channel 1 DIMM Control
  Enable / Disable DIMMs on Controller 0 Channel 1
  $EN_DIS
**/
  UINT8                       DisableMc0Ch1;

/** Offset 0x0194 - Controller 0 Channel 2 DIMM Control
  Enable / Disable DIMMs on Controller 0 Channel 2
  $EN_DIS
**/
  UINT8                       DisableMc0Ch2;

/** Offset 0x0195 - Controller 0 Channel 3 DIMM Control
  Enable / Disable DIMMs on Controller 0 Channel 3
  $EN_DIS
**/
  UINT8                       DisableMc0Ch3;

/** Offset 0x0196 - Controller 1 Channel 0 DIMM Control
  Enable / Disable DIMMs on Controller 1 Channel 0
  $EN_DIS
**/
  UINT8                       DisableMc1Ch0;

/** Offset 0x0197 - Controller 1 Channel 1 DIMM Control
  Enable / Disable DIMMs on Controller 1 Channel 1
  $EN_DIS
**/
  UINT8                       DisableMc1Ch1;

/** Offset 0x0198 - Controller 1 Channel 2 DIMM Control
  Enable / Disable DIMMs on Controller 1 Channel 2
  $EN_DIS
**/
  UINT8                       DisableMc1Ch2;

/** Offset 0x0199 - Controller 1 Channel 3 DIMM Control
  Enable / Disable DIMMs on Controller 1 Channel 3
  $EN_DIS
**/
  UINT8                       DisableMc1Ch3;

/** Offset 0x019A - Scrambler Support
  This option enables data scrambling in memory.
  $EN_DIS
**/
  UINT8                       ScramblerSupport;

/** Offset 0x019B - SPD Profile Selected
  Select DIMM timing profile. Options are 0:Default SPD Profile, 1:Custom Profile,
  2:XMP Profile 1, 3:XMP Profile 2, 4:XMP Profile 3, 5:XMP User Profile 4, 6:XMP
  User Profile 5
  0:Default SPD Profile, 1:Custom Profile, 2:XMP Profile 1, 3:XMP Profile 2, 4:XMP
  Profile 3, 5:XMP User Profile 4, 6:XMP User Profile 5
**/
  UINT8                       SpdProfileSelected;

/** Offset 0x019C - Reserved
**/
  UINT8                       Reserved7[3];

/** Offset 0x019F - Memory Reference Clock
  100MHz, 133MHz.
  0:133MHz, 1:100MHz
**/
  UINT8                       RefClk;

/** Offset 0x01A0 - Memory Vdd Voltage
  DRAM voltage (Vdd) (supply voltage for input buffers and core logic of the DRAM
  chips) in millivolts. <b>0=Platform Default (no override)</b>, 1200=1.2V, 1350=1.35V etc.
  0:Default, 1200:1.20 Volts, 1250:1.25 Volts, 1300:1.30 Volts, 1350:1.35 Volts, 1400:1.40
  Volts, 1450:1.45 Volts, 1500:1.50 Volts, 1550:1.55 Volts, 1600:1.60 Volts, 1650:1.65 Volts
**/
  UINT16                      VddVoltage;

/** Offset 0x01A2 - Reserved
**/
  UINT8                      Reserved8[4];

/** Offset 0x01A6 - Memory Ratio
  Automatic or the frequency will equal ratio times reference clock. Set to Auto to
  recalculate memory timings listed below.
  0:Auto, 4:4, 5:5, 6:6, 7:7, 8:8, 9:9, 10:10, 11:11, 12:12, 13:13, 14:14, 15:15
**/
  UINT16                      Ratio;

/** Offset 0x01A8 - tCL
  CAS Latency, 0: AUTO, max: 255. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT8                       tCL;

/** Offset 0x01A9 - tCWL
  Min CAS Write Latency Delay Time, 0: AUTO, max: 255. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT8                       tCWL;

/** Offset 0x01AA - tFAW
  Min Four Activate Window Delay Time, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT16                      tFAW;

/** Offset 0x01AC - tRAS
  RAS Active Time, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT16                      tRAS;

/** Offset 0x01AE - tRCD/tRP
  RAS to CAS delay time and Row Precharge delay time, 0: AUTO, max: 255. Only used
  if FspmUpd->FspmConfig.SpdProfileSelected == 1 (Custom Profile).
**/
  UINT8                       tRCDtRP;

/** Offset 0x01AF - Reserved
**/
  UINT8                       Reserved9;

/** Offset 0x01B0 - tREFI
  Refresh Interval, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT16                      tREFI;

/** Offset 0x01B2 - tRFC
  Min Refresh Recovery Delay Time, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT16                      tRFC;

/** Offset 0x01B4 - tRRD
  Min Row Active to Row Active Delay Time, 0: AUTO, max: 255. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT8                       tRRD;

/** Offset 0x01B5 - tRTP
  Min Internal Read to Precharge Command Delay Time, 0: AUTO, max: 255. Only used
  if FspmUpd->FspmConfig.SpdProfileSelected == 1 (Custom Profile).
**/
  UINT8                       tRTP;

/** Offset 0x01B6 - tWR
  Min Write Recovery Time, 0: AUTO, legal values: 5, 6, 7, 8, 10, 12, 14, 16, 18,
  20, 24, 30, 34, 40. Only used if FspmUpd->FspmConfig.SpdProfileSelected == 1 (Custom Profile).
  0:Auto, 5:5, 6:6, 7:7, 8:8, 10:10, 12:12, 14:14, 16:16, 18:18, 20:20, 24:24, 30:30,
  34:34, 40:40
**/
  UINT8                       tWR;

/** Offset 0x01B7 - tWTR
  Min Internal Write to Read Command Delay Time, 0: AUTO, max: 255. Only used if FspmUpd->FspmConfig.SpdProfileSelected
  == 1 (Custom Profile).
**/
  UINT8                       tWTR;

/** Offset 0x01B8 - Reserved
**/
  UINT8                      Reserved10[11];

/** Offset 0x01C3 - NMode
  System command rate, range 0-2, 0 means auto, 1 = 1N, 2 = 2N
**/
  UINT8                       NModeSupport;

/** Offset 0x01C4 - Enable Intel HD Audio (Azalia)
  0: Disable, 1: Enable (Default) Azalia controller
  $EN_DIS
**/
  UINT8                       PchHdaEnable;

/** Offset 0x01C5 - Enable PCH ISH Controller
  0: Disable, 1: Enable (Default) ISH Controller
  $EN_DIS
**/
  UINT8                       PchIshEnable;

/** Offset 0x01C6 - SAGV Gear Ratio
  Gear Selection for SAGV points. 0 - Auto, 2-Gear 2, 4-Gear 4
**/
  UINT8                       SaGvGear[4];

/** Offset 0x01CA - SAGV Frequency
  SAGV Frequency per point in Mhz. 0 for Auto and a ratio of 133/100MHz: 1333/1300.
**/
  UINT16                      SaGvFreq[4];

/** Offset 0x01D2 - SAGV Disabled Gear Ratio
  Gear Selection for SAGV Disabled. 0 - Auto, 2-Gear 2, 2-Gear 4
**/
  UINT8                       GearRatio;

/** Offset 0x01D3 - Reserved
**/
  UINT8                       Reserved11[69];

/** Offset 0x0218 - MMIO size adjustment for AUTO mode
  Positive number means increasing MMIO size, Negative value means decreasing MMIO
  size: 0 (Default)=no change to AUTO mode MMIO size
**/
  UINT16                      MmioSizeAdjustment;

/** Offset 0x021A - Selection of the primary display device
  0=iGFX, 3(Default)=AUTO, 4=Hybrid Graphics
  0:iGFX, 3:AUTO, 4:Hybrid Graphics
**/
  UINT8                       PrimaryDisplay;

/** Offset 0x021B - Reserved
**/
  UINT8                       Reserved12;

/** Offset 0x021C - Temporary MMIO address for GMADR
  Obsolete field now and it has been extended to 64 bit address, used LMemBar
**/
  UINT32                      GmAdr;

/** Offset 0x0220 - Temporary MMIO address for GTTMMADR
  The reference code will use this as Temporary MMIO address space to access GTTMMADR
  Registers.Platform should provide conflict free Temporary MMIO Range: GttMmAdr
  to (GttMmAdr + 2MB MMIO + 6MB Reserved + GttSize). Default is (GmAdr - (2MB MMIO
  + 6MB Reserved + GttSize)) to (GmAdr - 0x1) (Where GttSize = 8MB)
**/
  UINT32                      GttMmAdr;

/** Offset 0x0224 - Enable/Disable MRC TXT dependency
  When enabled MRC execution will wait for TXT initialization to be done first. Disabled(0x0)(Default):
  MRC will not wait for TXT initialization, Enabled(0x1): MRC will wait for TXT initialization
  $EN_DIS
**/
  UINT8                       TxtImplemented;

/** Offset 0x0225 - Enable/Disable SA OcSupport
  Enable: Enable SA OcSupport, Disable(Default): Disable SA OcSupport
  $EN_DIS
**/
  UINT8                       SaOcSupport;

/** Offset 0x0226 - GT slice Voltage Mode
  0(Default): Adaptive, 1: Override
  0: Adaptive, 1: Override
**/
  UINT8                       GtVoltageMode;

/** Offset 0x0227 - Maximum GTs turbo ratio override
  0(Default)=Minimal/Auto, 60=Maximum
**/
  UINT8                       GtMaxOcRatio;

/** Offset 0x0228 - The voltage offset applied to GT slice
  0(Default)=Minimal, 1000=Maximum
**/
  UINT16                      GtVoltageOffset;

/** Offset 0x022A - The GT slice voltage override which is applied to the entire range of GT frequencies
  0(Default)=Minimal, 2000=Maximum
**/
  UINT16                      GtVoltageOverride;

/** Offset 0x022C - adaptive voltage applied during turbo frequencies
  0(Default)=Minimal, 2000=Maximum
**/
  UINT16                      GtExtraTurboVoltage;

/** Offset 0x022E - voltage offset applied to the SA
  0(Default)=Minimal, 1000=Maximum
**/
  UINT16                      SaVoltageOffset;

/** Offset 0x0230 - PCIe root port Function number for Hybrid Graphics dGPU
  Root port Index number to indicate which PCIe root port has dGPU
**/
  UINT8                       RootPortIndex;

/** Offset 0x0231 - Realtime Memory Timing
  0(Default): Disabled, 1: Enabled. When enabled, it will allow the system to perform
  realtime memory timing changes after MRC_DONE.
  0: Disabled, 1: Enabled
**/
  UINT8                       RealtimeMemoryTiming;

/** Offset 0x0232 - Reserved
**/
  UINT8                       Reserved13;

/** Offset 0x0233 - Enable/Disable SA IPU
  Enable(Default): Enable SA IPU, Disable: Disable SA IPU
  $EN_DIS
**/
  UINT8                       SaIpuEnable;

/** Offset 0x0234 - IMGU CLKOUT Configuration
  The configuration of IMGU CLKOUT, 0: Disable;<b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       ImguClkOutEn[6];

/** Offset 0x023A - Program GPIOs for LFP on DDI port-A device
  0=Disabled,1(Default)=eDP, 2=MIPI DSI
  0:Disabled, 1:eDP, 2:MIPI DSI
**/
  UINT8                       DdiPortAConfig;

/** Offset 0x023B - Program GPIOs for LFP on DDI port-B device
  0(Default)=Disabled,1=eDP, 2=MIPI DSI
  0:Disabled, 1:eDP, 2:MIPI DSI
**/
  UINT8                       DdiPortBConfig;

/** Offset 0x023C - Enable or disable HPD of DDI port A
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPortAHpd;

/** Offset 0x023D - Enable or disable HPD of DDI port B
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortBHpd;

/** Offset 0x023E - Enable or disable HPD of DDI port C
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPortCHpd;

/** Offset 0x023F - Enable or disable HPD of DDI port 1
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPort1Hpd;

/** Offset 0x0240 - Enable or disable HPD of DDI port 2
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort2Hpd;

/** Offset 0x0241 - Enable or disable HPD of DDI port 3
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort3Hpd;

/** Offset 0x0242 - Enable or disable HPD of DDI port 4
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort4Hpd;

/** Offset 0x0243 - Enable or disable DDC of DDI port A
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPortADdc;

/** Offset 0x0244 - Enable or disable DDC of DDI port B
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortBDdc;

/** Offset 0x0245 - Enable or disable DDC of DDI port C
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPortCDdc;

/** Offset 0x0246 - Enable DDC setting of DDI Port 1
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort1Ddc;

/** Offset 0x0247 - Enable DDC setting of DDI Port 2
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort2Ddc;

/** Offset 0x0248 - Enable DDC setting of DDI Port 3
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort3Ddc;

/** Offset 0x0249 - Enable DDC setting of DDI Port 4
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       DdiPort4Ddc;

/** Offset 0x024A - Reserved
**/
  UINT8                       Reserved14[14];

/** Offset 0x0258 - Per-core HT Disable
  Defines the per-core HT disable mask where: 1 - Disable selected logical core HT,
  0 - is ignored. Input is in HEX and each bit maps to a logical core. Ex. A value
  of '1F' would disable HT for cores 4,3,2,1 and 0. Default is 0, all cores have
  HT enabled. Range is 0 - 0x7F for max 8 cores. You can only disable up to MAX_CORE_COUNT - 1.
**/
  UINT16                      PerCoreHtDisable;

/** Offset 0x025A - Reserved
**/
  UINT8                       Reserved15[6];

/** Offset 0x0260 - Thermal Velocity Boost Ratio clipping
  0: Disabled, 1(Default): Enabled. This service controls Core frequency reduction
  caused by high package temperatures for processors that implement the Intel Thermal
  Velocity Boost (TVB) feature
  $EN_DIS
**/
  UINT8                       TvbRatioClipping;

/** Offset 0x0261 - Thermal Velocity Boost voltage optimization
  0: Disabled, 1: Enabled(Default). This service controls thermal based voltage optimizations
  for processors that implement the Intel Thermal Velocity Boost (TVB) feature.
  $EN_DIS
**/
  UINT8                       TvbVoltageOptimization;

/** Offset 0x0262 - Reserved
**/
  UINT8                       Reserved16[47];

/** Offset 0x0291 - DMI Max Link Speed
  Auto (Default)(0x0): Maximum possible link speed, Gen1(0x1): Limit Link to Gen1
  Speed, Gen2(0x2): Limit Link to Gen2 Speed, Gen3(0x3):Limit Link to Gen3 Speed
  0:Auto, 1:Gen1, 2:Gen2, 3:Gen3
**/
  UINT8                       DmiMaxLinkSpeed;

/** Offset 0x0292 - DMI Equalization Phase 2
  DMI Equalization Phase 2. (0x0): Disable phase 2, (0x1): Enable phase 2, (0x2)(Default):
  AUTO - Use the current default method
  0:Disable phase2, 1:Enable phase2, 2:Auto
**/
  UINT8                       DmiGen3EqPh2Enable;

/** Offset 0x0293 - DMI Gen3 Equalization Phase3
  DMI Gen3 Equalization Phase3. Auto(0x0)(Default): Use the current default method,
  HwEq(0x1): Use Adaptive Hardware Equalization, SwEq(0x2): Use Adaptive Software
  Equalization (Implemented in BIOS Reference Code), Static(0x3): Use the Static
  EQs provided in DmiGen3EndPointPreset array for Phase1 AND Phase3 (Instead of just
  Phase1), Disabled(0x4): Bypass Equalization Phase 3
  0:Auto, 1:HwEq, 2:SwEq, 3:StaticEq, 4:BypassPhase3
**/
  UINT8                       DmiGen3EqPh3Method;

/** Offset 0x0294 - Enable/Disable DMI GEN3 Static EQ Phase1 programming
  Program DMI Gen3 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static
  Presets Programming, Enabled(0x1)(Default): Enable  EQ Phase1 Static Presets Programming
  $EN_DIS
**/
  UINT8                       DmiGen3ProgramStaticEq;

/** Offset 0x0295 - DMI Gen3 Root port preset values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-9, 4 is default for each lane
**/
  UINT8                       DmiGen3RootPortPreset[8];

/** Offset 0x029D - DMI Gen3 End port preset values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-9, 7 is default for each lane
**/
  UINT8                       DmiGen3EndPointPreset[8];

/** Offset 0x02A5 - DMI Gen3 End port Hint values per lane
  Used for programming DMI Gen3 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
  UINT8                       DmiGen3EndPointHint[8];

/** Offset 0x02AD - DMI ASPM Configuration:{Combo
  Set ASPM Configuration
  0:Disabled, 1:L0s, 2:L1, 3:L1L0s
**/
  UINT8                       DmiAspm;

/** Offset 0x02AE - Enable/Disable DMI GEN3 Hardware Eq
  Enable/Disable DMI GEN3 Hardware Eq. Disabled(0x0): Disable Hardware Eq, Enabled(0x1)(Default):
  Enable  EQ Phase1 Static Presets Programming
  $EN_DIS
**/
  UINT8                       DmiHweq;

/** Offset 0x02AF - Enable/Disable DMI GEN3 Phase 23 Bypass
  DMIGEN3 Phase 23 Bypass. Disabled(0x0)(Default): Disable Phase 23 Bypass, Enabled(0x1):
  Enable  Phase 23 Bypass
  $EN_DIS
**/
  UINT8                       Gen3EqPhase23Bypass;

/** Offset 0x02B0 - Enable/Disable DMI GEN3 Phase 3 Bypass
  DMIGEN3 Phase 3 Bypass. Disabled(0x0)(Default): Disable Phase 3 Bypass, Enabled(0x1):
  Enable  Phase 3 Bypass
  $EN_DIS
**/
  UINT8                       Gen3EqPhase3Bypass;

/** Offset 0x02B1 - Enable/Disable DMI Gen3 EQ Local Transmitter Coefficient Override Enable
  Program Gen3 EQ Local Transmitter Coefficient Override. Disabled(0x0): Disable Local
  Transmitter Coefficient Override, Enabled(0x1)(Default): Enable  Local Transmitter
  Coefficient Override
  $EN_DIS
**/
  UINT8                       Gen3LtcoEnable;

/** Offset 0x02B2 - Enable/Disable DMI Gen3 EQ Remote Transmitter Coefficient/Preset Override Enable
  Program Remote Transmitter Coefficient/Preset Override. Disabled(0x0)(Default):
  Disable Remote Transmitter Coefficient/Preset Override, Enabled(0x1): Enable  Remote
  Transmitter Coefficient/Preset Override
  $EN_DIS
**/
  UINT8                       Gen3RtcoRtpoEnable;

/** Offset 0x02B3 - DMI Gen3 Transmitter Pre-Cursor Coefficient
  Used for programming DMI Gen3 Transmitter Pre-Cursor Coefficient . Range: 0-10,
  2 is default for each lane
**/
  UINT8                       DmiGen3Ltcpre[8];

/** Offset 0x02BB - DMI Gen3 Transmitter Post-Cursor Coefficient
  Used for programming Transmitter Post-Cursor Coefficient. Range: 0-9, 2 is default
  for each lane
**/
  UINT8                       DmiGen3Ltcpo[8];

/** Offset 0x02C3 - Reserved
**/
  UINT8                       Reserved17[16];

/** Offset 0x02D3 - Enable/Disable DMI GEN3 DmiGen3DsPresetEnable
  Enable/Disable DMI GEN3 DmiGen3DsPreset. Auto(0x0)(Default): DmiGen3DsPresetEnable,
  Manual(0x1): Enable DmiGen3DsPresetEnable
  $EN_DIS
**/
  UINT8                       DmiGen3DsPresetEnable;

/** Offset 0x02D4 - DMI Gen3 Root port preset Rx values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-10, 1 is default
  for each lane
**/
  UINT8                       DmiGen3DsPortRxPreset[8];

/** Offset 0x02DC - DMI Gen3 Root port preset Tx values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-10, 7 is default
  for each lane
**/
  UINT8                       DmiGen3DsPortTxPreset[8];

/** Offset 0x02E4 - Enable/Disable DMI GEN3 DmiGen3UsPresetEnable
  Enable/Disable DMI GEN3 DmiGen3UsPreset. Auto(0x0)(Default): DmiGen3UsPresetEnable,
  Manual(0x1): Enable DmiGen3UsPresetEnable
  $EN_DIS
**/
  UINT8                       DmiGen3UsPresetEnable;

/** Offset 0x02E5 - DMI Gen3 Root port preset Rx values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-10, 7 is default
  for each lane
**/
  UINT8                       DmiGen3UsPortRxPreset[8];

/** Offset 0x02ED - DMI Gen3 Root port preset Tx values per lane
  Used for programming DMI Gen3 preset values per lane. Range: 0-10, 1 is default
  for each lane
**/
  UINT8                       DmiGen3UsPortTxPreset[8];

/** Offset 0x02F5 - Reserved
**/
  UINT8                       Reserved18[54];

/** Offset 0x032B - DMI ASPM L1 exit Latency
  Range: 0-7, 4 is default L1 exit Latency
**/
  UINT8                       DmiAspmL1ExitLatency;

/** Offset 0x032C - Reserved
**/
  UINT8                       Reserved19[40];

/** Offset 0x0354 - BIST on Reset
  Enable/Disable BIST (Built-In Self Test) on reset. <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       BistOnReset;

/** Offset 0x0355 - Skip Stop PBET Timer Enable/Disable
  Skip Stop PBET Timer; <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       SkipStopPbet;

/** Offset 0x0356 - Over clocking support
  Over clocking support; <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       OcSupport;

/** Offset 0x0357 - Over clocking Lock
  Lock Overclocking. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       OcLock;

/** Offset 0x0358 - Maximum Core Turbo Ratio Override
  Maximum core turbo ratio override allows to increase CPU core frequency beyond the
  fused max turbo ratio limit. <b>0: Hardware defaults.</b> Range: 0-85 if CoreRatioExtensionMode
  is disabled. 0-120 if CoreRatioExtensionMode is enabled.
**/
  UINT8                       CoreMaxOcRatio;

/** Offset 0x0359 - Core voltage mode
  Core voltage mode; <b>0: Adaptive</b>; 1: Override.
  $EN_DIS
**/
  UINT8                       CoreVoltageMode;

/** Offset 0x035A - Maximum clr turbo ratio override
  Maximum clr turbo ratio override allows to increase CPU clr frequency beyond the
  fused max turbo ratio limit. <b>0: Hardware defaults.</b>  Range: 0-85
**/
  UINT8                       RingMaxOcRatio;

/** Offset 0x035B - Hyper Threading Enable/Disable
  Enable or Disable Hyper-Threading Technology. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       HyperThreading;

/** Offset 0x035C - Enable or Disable CPU Ratio Override
  Enable/Disable CPU Flex Ratio Programming; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       CpuRatioOverride;

/** Offset 0x035D - CPU ratio value
  This value must be between Max Efficiency Ratio (LFM) and Maximum non-turbo ratio
  set by Hardware (HFM). Valid Range 0 to 63.
**/
  UINT8                       CpuRatio;

/** Offset 0x035E - Reserved
**/
  UINT8                       Reserved20;

/** Offset 0x035F - Number of active big cores
  Number of P-cores to enable in each processor package. Note: Number of P-Cores and
  E-Cores are looked at together. When both are {0,0
  0:Disable all big cores, 1:1, 2:2, 3:3, 0xFF:Active all big cores
**/
  UINT8                       ActiveCoreCount;

/** Offset 0x0360 - Processor Early Power On Configuration FCLK setting
  FCLK frequency can take values of 400MHz, 800MHz and 1GHz. <b>0: 800 MHz (ULT/ULX)</b>.
  <b>1: 1 GHz (DT/Halo)</b>. Not supported on ULT/ULX.- 2: 400 MHz. - 3: Reserved
  0:800 MHz, 1: 1 GHz, 2: 400 MHz, 3: Reserved
**/
  UINT8                       FClkFrequency;

/** Offset 0x0361 - Enable or Disable VMX
  Enable or Disable VMX, When enabled, a VMM can utilize the additional hardware capabilities
  provided by Vanderpool Technology. 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       VmxEnable;

/** Offset 0x0362 - AVX2 Ratio Offset
  0(Default)= No Offset. Range 0 - 31. Specifies number of bins to decrease AVX ratio
  vs. Core Ratio. Uses Mailbox MSR 0x150, cmd 0x1B.
**/
  UINT8                       Avx2RatioOffset;

/** Offset 0x0363 - AVX3 Ratio Offset
  0(Default)= No Offset. Range 0 - 31. Specifies number of bins to decrease AVX ratio
  vs. Core Ratio. Uses Mailbox MSR 0x150, cmd 0x1B.
**/
  UINT8                       Avx3RatioOffset;

/** Offset 0x0364 - BCLK Adaptive Voltage Enable
  When enabled, the CPU V/F curves are aware of BCLK frequency when calculated. </b>0:
  Disable;<b> 1: Enable
  $EN_DIS
**/
  UINT8                       BclkAdaptiveVoltage;

/** Offset 0x0365 - Reserved
**/
  UINT8                       Reserved21;

/** Offset 0x0366 - core voltage override
  The core voltage override which is applied to the entire range of cpu core frequencies.
  Valid Range 0 to 2000
**/
  UINT16                      CoreVoltageOverride;

/** Offset 0x0368 - Core Turbo voltage Adaptive
  Extra Turbo voltage applied to the cpu core when the cpu is operating in turbo mode.
  Valid Range 0 to 2000
**/
  UINT16                      CoreVoltageAdaptive;

/** Offset 0x036A - Core Turbo voltage Offset
  The voltage offset applied to the core while operating in turbo mode.Valid Range 0 to 1000
**/
  UINT16                      CoreVoltageOffset;

/** Offset 0x036C - Core PLL voltage offset
  Core PLL voltage offset. <b>0: No offset</b>. Range 0-15
**/
  UINT8                       CorePllVoltageOffset;

/** Offset 0x036D - Ring Downbin
  Ring Downbin enable/disable. When enabled, CPU will ensure the ring ratio is always
  lower than the core ratio.0: Disable; <b>1: Enable.</b>
  $EN_DIS
**/
  UINT8                       RingDownBin;

/** Offset 0x036E - Ring voltage mode
  Ring voltage mode; <b>0: Adaptive</b>; 1: Override.
  $EN_DIS
**/
  UINT8                       RingVoltageMode;

/** Offset 0x036F - TjMax Offset
  TjMax offset.Specified value here is clipped by pCode (125 - TjMax Offset) to support
  TjMax in the range of 62 to 115 deg Celsius. Valid Range 10 - 63
**/
  UINT8                       TjMaxOffset;

/** Offset 0x0370 - Ring voltage override
  The ring voltage override which is applied to the entire range of cpu ring frequencies.
  Valid Range 0 to 2000
**/
  UINT16                      RingVoltageOverride;

/** Offset 0x0372 - Ring Turbo voltage Adaptive
  Extra Turbo voltage applied to the cpu ring when the cpu is operating in turbo mode.
  Valid Range 0 to 2000
**/
  UINT16                      RingVoltageAdaptive;

/** Offset 0x0374 - Ring Turbo voltage Offset
  The voltage offset applied to the ring while operating in turbo mode. Valid Range 0 to 1000
**/
  UINT16                      RingVoltageOffset;

/** Offset 0x0376 - Enable or Disable TME
  Configure Total Memory Encryption (TME) to protect DRAM data from physical attacks.
  <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       TmeEnable;

/** Offset 0x0377 - Enable CPU CrashLog
  Enable or Disable CPU CrashLog; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       CpuCrashLogEnable;

/** Offset 0x0378 - CPU Run Control
  Enable, Disable or Do not configure CPU Run Control; 0: Disable; 1: Enable ; <b>2:
  No Change</b>
  0:Disabled, 1:Enabled, 2:No Change
**/
  UINT8                       DebugInterfaceEnable;

/** Offset 0x0379 - CPU Run Control Lock
  Lock or Unlock CPU Run Control; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       DebugInterfaceLockEnable;

/** Offset 0x037A - Reserved
**/
  UINT8                       Reserved22[67];

/** Offset 0x03BD - Core VF Point Offset Mode
  Selects Core Voltage & Frequency Offset mode between Legacy and Selection modes.
  In Legacy Mode, setting a global offset for the entire VF curve. In Selection Mode,
  setting a selected VF point; <b>0: Legacy</b>; 1: Selection.
  0:Legacy, 1:Selection
**/
  UINT8                       CoreVfPointOffsetMode;

/** Offset 0x03BE - Core VF Point Offset
  Array used to specifies the Core Voltage Offset applied to the each selected VF
  Point. This voltage is specified in millivolts.
**/
  UINT16                      CoreVfPointOffset[15];

/** Offset 0x03DC - Core VF Point Offset Prefix
  Sets the CoreVfPointOffset value as positive or negative for corresponding core
  VF Point; <b>0: Positive </b>; 1: Negative.
  0:Positive, 1:Negative
**/
  UINT8                       CoreVfPointOffsetPrefix[15];

/** Offset 0x03EB - Core VF Point Ratio
  Array for the each selected Core VF Point to display the ration.
**/
  UINT8                       CoreVfPointRatio[15];

/** Offset 0x03FA - Core VF Point Count
  Number of supported Core Voltage & Frequency Point Offset
**/
  UINT8                       CoreVfPointCount;

/** Offset 0x03FB - Reserved
**/
  UINT8                       Reserved23[25];

/** Offset 0x0414 - Per Core Max Ratio override
  Enable or disable Per Core PState OC supported by writing OCMB 0x1D to program new
  favored core ratio to each Core. <b>0: Disable</b>, 1: enable
  $EN_DIS
**/
  UINT8                       PerCoreRatioOverride;

/** Offset 0x0415 - Reserved
**/
  UINT8                       Reserved24[41];

/** Offset 0x043E - Per Core Current Max Ratio
  Array for the Per Core Max Ratio
**/
  UINT8                       PerCoreRatio[8];

/** Offset 0x0446 - Reserved
**/
  UINT8                       Reserved25[69];

/** Offset 0x048B - Pvd Ratio Threshold for SOC/CPU die
  Array of Pvd Ratio Threshold for SOC/CPU die is the threshold value for input ratio
  (P0 to Pn) to select the multiplier so that the output is within the DCO frequency
  range. As per the die selected, this threshold is applied to SA and MC/CMI PLL
  for SOC die and SA, Ring and Atom PLL for CPU die. Range 0-63. When the threshold
  is 0, static PVD ratio is selected based on the PVD Mode for SOC. <b>0: Default</b>.
**/
  UINT8                       PvdRatioThreshold[2];

/** Offset 0x048D - Reserved
**/
  UINT8                       Reserved26[70];

/** Offset 0x04D3 - BCLK Frequency Source
  Clock source of BCLK OC frequency, <b>0:CPU BCLK</b>, 1:PCH BCLK, 2:External CLK
  0:CPU BCLK, 1:PCH BCLK, 2:External CLK
**/
  UINT8                       BclkSource;

/** Offset 0x04D4 - GPIO Override
  Gpio Override Level - FSP will not configure any GPIOs and rely on GPIO setings
  before moved to FSP. Available configurations 0: Disable; 1: Level 1 - Skips GPIO
  configuration in PEI/FSPM/FSPT phase;2: Level 2 - Reserved for use
**/
  UINT8                       GpioOverride;

/** Offset 0x04D5 - Reserved
**/
  UINT8                       Reserved27[7];

/** Offset 0x04DC - CPU BCLK OC Frequency
  CPU BCLK OC Frequency in KHz units. 98000000Hz = 98MHz <b>0 - Auto</b>. Range is
  40Mhz-1000Mhz.
**/
  UINT32                      CpuBclkOcFrequency;

/** Offset 0x04E0 - Reserved
**/
  UINT8                      Reserved28[4];

/** Offset 0x04E4 - Enable CPU CrashLog GPRs dump
  Enable or Disable CPU CrashLog GPRs dump; <b>0: Disable</b>; 1: Enable; 2: Only
  disable Smm GPRs dump
  0:Disabled, 1:Enabled, 2:Only Smm GPRs Disabled
**/
  UINT8                       CrashLogGprs;

/** Offset 0x04E5 - Reserved
**/
  UINT8                       Reserved29[269];

/** Offset 0x05F2 - Thermal Design Current enable/disable
  Thermal Design Current enable/disable; <b>0: Disable</b>; 1: Enable. [0] for IA,
  [1] for GT, [2] for SA, [3] through [5] are Reserved.
**/
  UINT8                       TdcEnable[6];

/** Offset 0x05F8 - Thermal Design Current time window
  TDC Time Window, value of IA either in milliseconds or seconds, value of GT/SA is
  in milliseconds. 1ms is default. Range of IA from 1ms to 448s, Range of GT/SA is
  1ms to 10ms, except for 9ms. 9ms has no valid encoding in the MSR definition.
**/
  UINT32                      TdcTimeWindow[6];

/** Offset 0x0610 - Reserved
**/
  UINT8                       Reserved30[208];

/** Offset 0x06E0 - BiosGuard
  Enable/Disable. 0: Disable, Enable/Disable BIOS Guard feature, 1: enable
  $EN_DIS
**/
  UINT8                       BiosGuard;

/** Offset 0x06E1
**/
  UINT8                       BiosGuardToolsInterface;

/** Offset 0x06E2 - Txt
  Enables utilization of additional hardware capabilities provided by Intel (R) Trusted
  Execution Technology. Changes require a full power cycle to take effect. <b>0:
  Disable</b>, 1: Enable
  $EN_DIS
**/
  UINT8                       Txt;

/** Offset 0x06E3 - Reserved
**/
  UINT8                       Reserved31;

/** Offset 0x06E4 - PrmrrSize
  Enable/Disable. 0: Disable, define default value of PrmrrSize , 1: enable
**/
  UINT32                      PrmrrSize;

/** Offset 0x06E8 - SinitMemorySize
  Enable/Disable. 0: Disable, define default value of SinitMemorySize , 1: enable
**/
  UINT32                      SinitMemorySize;

/** Offset 0x06EC - Reserved
**/
  UINT8                       Reserved32[4];

/** Offset 0x06F0 - TxtDprMemoryBase
  Enable/Disable. 0: Disable, define default value of TxtDprMemoryBase , 1: enable
**/
  UINT64                      TxtDprMemoryBase;

/** Offset 0x06F8 - TxtHeapMemorySize
  Enable/Disable. 0: Disable, define default value of TxtHeapMemorySize , 1: enable
**/
  UINT32                      TxtHeapMemorySize;

/** Offset 0x06FC - TxtDprMemorySize
  Reserve DPR memory size (0-255) MB. 0: Disable, define default value of TxtDprMemorySize
  , 1: enable
**/
  UINT32                      TxtDprMemorySize;

/** Offset 0x0700 - BiosAcmBase
  Enable/Disable. 0: Disable, define default value of BiosAcmBase , 1: enable
**/
  UINT32                      BiosAcmBase;

/** Offset 0x0704 - BiosAcmSize
  Enable/Disable. 0: Disable, define default value of BiosAcmSize , 1: enable
**/
  UINT32                      BiosAcmSize;

/** Offset 0x0708 - ApStartupBase
  Enable/Disable. 0: Disable, define default value of BiosAcmBase , 1: enable
**/
  UINT32                      ApStartupBase;

/** Offset 0x070C - TgaSize
  Enable/Disable. 0: Disable, define default value of TgaSize , 1: enable
**/
  UINT32                      TgaSize;

/** Offset 0x0710 - TxtLcpPdBase
  Enable/Disable. 0: Disable, define default value of TxtLcpPdBase , 1: enable
**/
  UINT64                      TxtLcpPdBase;

/** Offset 0x0718 - TxtLcpPdSize
  Enable/Disable. 0: Disable, define default value of TxtLcpPdSize , 1: enable
**/
  UINT64                      TxtLcpPdSize;

/** Offset 0x0720 - IsTPMPresence
  IsTPMPresence default values
**/
  UINT8                       IsTPMPresence;

/** Offset 0x0721 - Reserved
**/
  UINT8                       Reserved33[32];

/** Offset 0x0741 - Enable PCH HSIO PCIE Rx Set Ctle
  Enable PCH PCIe Gen 3 Set CTLE Value.
**/
  UINT8                       PchPcieHsioRxSetCtleEnable[28];

/** Offset 0x075D - PCH HSIO PCIE Rx Set Ctle Value
  PCH PCIe Gen 3 Set CTLE Value.
**/
  UINT8                       PchPcieHsioRxSetCtle[28];

/** Offset 0x0779 - Enble PCH HSIO PCIE TX Gen 1 Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen1DownscaleAmpEnable[28];

/** Offset 0x0795 - PCH HSIO PCIE Gen 2 TX Output Downscale Amplitude Adjustment value
  PCH PCIe Gen 2 TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchPcieHsioTxGen1DownscaleAmp[28];

/** Offset 0x07B1 - Enable PCH HSIO PCIE TX Gen 2 Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen2DownscaleAmpEnable[28];

/** Offset 0x07CD - PCH HSIO PCIE Gen 2 TX Output Downscale Amplitude Adjustment value
  PCH PCIe Gen 2 TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchPcieHsioTxGen2DownscaleAmp[28];

/** Offset 0x07E9 - Enable PCH HSIO PCIE TX Gen 3 Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen3DownscaleAmpEnable[28];

/** Offset 0x0805 - PCH HSIO PCIE Gen 3 TX Output Downscale Amplitude Adjustment value
  PCH PCIe Gen 3 TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchPcieHsioTxGen3DownscaleAmp[28];

/** Offset 0x0821 - Enable PCH HSIO PCIE Gen 1 TX Output De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen1DeEmphEnable[28];

/** Offset 0x083D - PCH HSIO PCIE Gen 1 TX Output De-Emphasis Adjustment value
  PCH PCIe Gen 1 TX Output De-Emphasis Adjustment Setting.
**/
  UINT8                       PchPcieHsioTxGen1DeEmph[28];

/** Offset 0x0859 - Enable PCH HSIO PCIE Gen 2 TX Output -3.5dB De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen2DeEmph3p5Enable[28];

/** Offset 0x0875 - PCH HSIO PCIE Gen 2 TX Output -3.5dB De-Emphasis Adjustment value
  PCH PCIe Gen 2 TX Output -3.5dB De-Emphasis Adjustment Setting.
**/
  UINT8                       PchPcieHsioTxGen2DeEmph3p5[28];

/** Offset 0x0891 - Enable PCH HSIO PCIE Gen 2 TX Output -6.0dB De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchPcieHsioTxGen2DeEmph6p0Enable[28];

/** Offset 0x08AD - PCH HSIO PCIE Gen 2 TX Output -6.0dB De-Emphasis Adjustment value
  PCH PCIe Gen 2 TX Output -6.0dB De-Emphasis Adjustment Setting.
**/
  UINT8                       PchPcieHsioTxGen2DeEmph6p0[28];

/** Offset 0x08C9 - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioRxGen1EqBoostMagEnable[8];

/** Offset 0x08D1 - PCH HSIO SATA 1.5 Gb/s Receiver Equalization Boost Magnitude Adjustment value
  PCH HSIO SATA 1.5 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
  UINT8                       PchSataHsioRxGen1EqBoostMag[8];

/** Offset 0x08D9 - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioRxGen2EqBoostMagEnable[8];

/** Offset 0x08E1 - PCH HSIO SATA 3.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value
  PCH HSIO SATA 3.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
  UINT8                       PchSataHsioRxGen2EqBoostMag[8];

/** Offset 0x08E9 - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioRxGen3EqBoostMagEnable[8];

/** Offset 0x08F1 - PCH HSIO SATA 6.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value
  PCH HSIO SATA 6.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
  UINT8                       PchSataHsioRxGen3EqBoostMag[8];

/** Offset 0x08F9 - Enable PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen1DownscaleAmpEnable[8];

/** Offset 0x0901 - PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value
  PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchSataHsioTxGen1DownscaleAmp[8];

/** Offset 0x0909 - Enable PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen2DownscaleAmpEnable[8];

/** Offset 0x0911 - PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value
  PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchSataHsioTxGen2DownscaleAmp[8];

/** Offset 0x0919 - Enable PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen3DownscaleAmpEnable[8];

/** Offset 0x0921 - PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value
  PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
  UINT8                       PchSataHsioTxGen3DownscaleAmp[8];

/** Offset 0x0929 - Enable PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen1DeEmphEnable[8];

/** Offset 0x0931 - PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting
  PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
  UINT8                       PchSataHsioTxGen1DeEmph[8];

/** Offset 0x0939 - Enable PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen2DeEmphEnable[8];

/** Offset 0x0941 - PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting
  PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
  UINT8                       PchSataHsioTxGen2DeEmph[8];

/** Offset 0x0949 - Enable PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting value override
  0: Disable; 1: Enable.
**/
  UINT8                       PchSataHsioTxGen3DeEmphEnable[8];

/** Offset 0x0951 - PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting
  PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
  UINT8                       PchSataHsioTxGen3DeEmph[8];

/** Offset 0x0959 - PCH LPC Enhance the port 8xh decoding
  Original LPC only decodes one byte of port 80h.
  $EN_DIS
**/
  UINT8                       PchLpcEnhancePort8xhDecoding;

/** Offset 0x095A - PCH Port80 Route
  Control where the Port 80h cycles are sent, 0: LPC; 1: PCI.
  $EN_DIS
**/
  UINT8                       PchPort80Route;

/** Offset 0x095B - Enable SMBus ARP support
  Enable SMBus ARP support.
  $EN_DIS
**/
  UINT8                       SmbusArpEnable;

/** Offset 0x095C - Number of RsvdSmbusAddressTable.
  The number of elements in the RsvdSmbusAddressTable.
**/
  UINT8                       PchNumRsvdSmbusAddresses;

/** Offset 0x095D - Reserved
**/
  UINT8                       Reserved34;

/** Offset 0x095E - SMBUS Base Address
  SMBUS Base Address (IO space).
**/
  UINT16                      PchSmbusIoBase;

/** Offset 0x0960 - Enable SMBus Alert Pin
  Enable SMBus Alert Pin.
  $EN_DIS
**/
  UINT8                       PchSmbAlertEnable;

/** Offset 0x0961 - Usage type for ClkSrc
  0-23: PCH rootport, 0x70:LAN, 0x80: unspecified but in use (free running), 0xFF: not used
**/
  UINT8                       PcieClkSrcUsage[18];

/** Offset 0x0973 - Reserved
**/
  UINT8                       Reserved35[14];

/** Offset 0x0981 - ClkReq-to-ClkSrc mapping
  Number of ClkReq signal assigned to ClkSrc
**/
  UINT8                       PcieClkSrcClkReq[18];

/** Offset 0x0993 - Reserved
**/
  UINT8                       Reserved36[57];

/** Offset 0x09CC - Enable SOC/IOE PCIE RP Mask
  Enable/disable SOC/IOE PCIE Root Ports. 0: disable, 1: enable. One bit for each
  port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT16                      PcieRpEnableMask;

/** Offset 0x09CE - VC Type
  Virtual Channel Type Select: 0: VC0, 1: VC1.
  0: VC0, 1: VC1
**/
  UINT8                       PchHdaVcType;

/** Offset 0x09CF - Universal Audio Architecture compliance for DSP enabled system
  0: Not-UAA Compliant (Intel SST driver supported only), 1: UAA Compliant (HDA Inbox
  driver or SST driver supported).
  $EN_DIS
**/
  UINT8                       PchHdaDspUaaCompliance;

/** Offset 0x09D0 - Enable HD Audio Link
  Enable/disable HD Audio Link. Muxed with SSP0/SSP1/SNDW1.
  $EN_DIS
**/
  UINT8                       PchHdaAudioLinkHdaEnable;

/** Offset 0x09D1 - Enable HDA SDI lanes
  Enable/disable HDA SDI lanes.
**/
  UINT8                       PchHdaSdiEnable[2];

/** Offset 0x09D3 - HDA Power/Clock Gating (PGD/CGD)
  Enable/Disable HD Audio Power and Clock Gating(POR: Enable). 0: PLATFORM_POR, 1:
  FORCE_ENABLE, 2: FORCE_DISABLE.
  0: POR, 1: Force Enable, 2: Force Disable
**/
  UINT8                       PchHdaTestPowerClockGating;

/** Offset 0x09D4 - Enable HD Audio DMIC_N Link
  Enable/disable HD Audio DMIC1 link. Muxed with SNDW3.
**/
  UINT8                       PchHdaAudioLinkDmicEnable[2];

/** Offset 0x09D6 - Reserved
**/
  UINT8                       Reserved37[2];

/** Offset 0x09D8 - DMIC<N> ClkA Pin Muxing (N - DMIC number)
  Determines DMIC<N> ClkA Pin muxing. See  GPIO_*_MUXING_DMIC<N>_CLKA_*
**/
  UINT32                      PchHdaAudioLinkDmicClkAPinMux[2];

/** Offset 0x09E0 - DMIC<N> ClkB Pin Muxing
  Determines DMIC<N> ClkA Pin muxing. See GPIO_*_MUXING_DMIC<N>_CLKB_*
**/
  UINT32                      PchHdaAudioLinkDmicClkBPinMux[2];

/** Offset 0x09E8 - Enable HD Audio DSP
  Enable/disable HD Audio DSP feature.
  $EN_DIS
**/
  UINT8                       PchHdaDspEnable;

/** Offset 0x09E9 - Reserved
**/
  UINT8                       Reserved38[3];

/** Offset 0x09EC - DMIC<N> Data Pin Muxing
  Determines DMIC<N> Data Pin muxing. See GPIO_*_MUXING_DMIC<N>_DATA_*
**/
  UINT32                      PchHdaAudioLinkDmicDataPinMux[2];

/** Offset 0x09F4 - Enable HD Audio SSP0 Link
  Enable/disable HD Audio SSP_N/I2S link. Muxed with HDA. N-number 0-5
**/
  UINT8                       PchHdaAudioLinkSspEnable[6];

/** Offset 0x09FA - Enable HD Audio SoundWire#N Link
  Enable/disable HD Audio SNDW#N link. Muxed with HDA.
**/
  UINT8                       PchHdaAudioLinkSndwEnable[4];

/** Offset 0x09FE - iDisp-Link Frequency
  iDisp-Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 4: 96MHz, 3: 48MHz.
  4: 96MHz, 3: 48MHz
**/
  UINT8                       PchHdaIDispLinkFrequency;

/** Offset 0x09FF - Reserved
**/
  UINT8                       Reserved39;

/** Offset 0x0A00 - iDisp-Link T-mode
  iDisp-Link T-Mode (PCH_HDAUDIO_IDISP_TMODE enum): 0: 2T, 2: 4T, 3: 8T, 4: 16T
  0: 2T, 2: 4T, 3: 8T, 4: 16T
**/
  UINT8                       PchHdaIDispLinkTmode;

/** Offset 0x0A01 - iDisplay Audio Codec disconnection
  0: Not disconnected, enumerable, 1: Disconnected SDI, not enumerable.
  $EN_DIS
**/
  UINT8                       PchHdaIDispCodecDisconnect;

/** Offset 0x0A02 - Reserved
**/
  UINT8                       Reserved40[6];

/** Offset 0x0A08 - CNVi DDR RFI Mitigation
  Enable/Disable DDR RFI Mitigation. Default is ENABLE. 0: DISABLE, 1: ENABLE
  $EN_DIS
**/
  UINT8                       CnviDdrRfim;

/** Offset 0x0A09 - Reserved
**/
  UINT8                       Reserved41[11];

/** Offset 0x0A14 - Debug Interfaces
  Debug Interfaces. BIT0-RAM, BIT1-UART, BIT3-USB3, BIT4-Serial IO, BIT5-TraceHub,
  BIT2 - Not used.
**/
  UINT8                       PcdDebugInterfaceFlags;

/** Offset 0x0A15 - Serial Io Uart Debug Controller Number
  Select SerialIo Uart Controller for debug.
  0:SerialIoUart0, 1:SerialIoUart1, 2:SerialIoUart2
**/
  UINT8                       SerialIoUartDebugControllerNumber;

/** Offset 0x0A16 - Serial Io Uart Debug Auto Flow
  Enables UART hardware flow control, CTS and RTS lines.
  $EN_DIS
**/
  UINT8                       SerialIoUartDebugAutoFlow;

/** Offset 0x0A17 - Reserved
**/
  UINT8                       Reserved42;

/** Offset 0x0A18 - Serial Io Uart Debug BaudRate
  Set default BaudRate Supported from 0 - default to 6000000. Recommended values 9600,
  19200, 57600, 115200, 460800, 921600, 1500000, 1843200, 3000000, 3686400, 6000000
**/
  UINT32                      SerialIoUartDebugBaudRate;

/** Offset 0x0A1C - Serial Io Uart Debug Parity
  Set default Parity.
  0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
**/
  UINT8                       SerialIoUartDebugParity;

/** Offset 0x0A1D - Serial Io Uart Debug Stop Bits
  Set default stop bits.
  0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3: TwoStopBits
**/
  UINT8                       SerialIoUartDebugStopBits;

/** Offset 0x0A1E - Serial Io Uart Debug Data Bits
  Set default word length. 0: Default, 5,6,7,8
  5:5BITS, 6:6BITS, 7:7BITS, 8:8BITS
**/
  UINT8                       SerialIoUartDebugDataBits;

/** Offset 0x0A1F - Reserved
**/
  UINT8                       Reserved43;

/** Offset 0x0A20 - Serial Io Uart Debug Mmio Base
  Select SerialIo Uart default MMIO resource in SEC/PEI phase when PcdSerialIoUartMode
  = SerialIoUartPci.
**/
  UINT32                      SerialIoUartDebugMmioBase;

/** Offset 0x0A24 - ISA Serial Base selection
  Select ISA Serial Base address. Default is 0x3F8.
  0:0x3F8, 1:0x2F8
**/
  UINT8                       PcdIsaSerialUartBase;

/** Offset 0x0A25 - Reserved
**/
  UINT8                       Reserved44;

/** Offset 0x0A26 - Ring PLL voltage offset
  Core PLL voltage offset. <b>0: No offset</b>. Range 0-15
**/
  UINT8                       RingPllVoltageOffset;

/** Offset 0x0A27 - System Agent PLL voltage offset
  Core PLL voltage offset. <b>0: No offset</b>. Range 0-15
**/
  UINT8                       SaPllVoltageOffset;

/** Offset 0x0A28 - Reserved
**/
  UINT8                       Reserved45;

/** Offset 0x0A29 - Memory Controller PLL voltage offset
  Core PLL voltage offset. <b>0: No offset</b>. Range 0-15
**/
  UINT8                       McPllVoltageOffset;

/** Offset 0x0A2A - TCSS Thunderbolt PCIE Root Port 0 Enable
  Set TCSS Thunderbolt PCIE Root Port 0. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssItbtPcie0En;

/** Offset 0x0A2B - TCSS Thunderbolt PCIE Root Port 1 Enable
  Set TCSS Thunderbolt PCIE Root Port 1. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssItbtPcie1En;

/** Offset 0x0A2C - TCSS Thunderbolt PCIE Root Port 2 Enable
  Set TCSS Thunderbolt PCIE Root Port 2. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssItbtPcie2En;

/** Offset 0x0A2D - TCSS Thunderbolt PCIE Root Port 3 Enable
  Set TCSS Thunderbolt PCIE Root Port 3. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssItbtPcie3En;

/** Offset 0x0A2E - TCSS USB HOST (xHCI) Enable
  Set TCSS XHCI. 0:Disabled  1:Enabled - Must be enabled if xDCI is enabled below
  $EN_DIS
**/
  UINT8                       TcssXhciEn;

/** Offset 0x0A2F - TCSS USB DEVICE (xDCI) Enable
  Set TCSS XDCI. 0:Disabled  1:Enabled - xHCI must be enabled if xDCI is enabled
  $EN_DIS
**/
  UINT8                       TcssXdciEn;

/** Offset 0x0A30 - TCSS DMA0 Enable
  Set TCSS DMA0. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssDma0En;

/** Offset 0x0A31 - TCSS DMA1 Enable
  Set TCSS DMA1. 0:Disabled  1:Enabled
  $EN_DIS
**/
  UINT8                       TcssDma1En;

/** Offset 0x0A32 - PcdSerialDebugBaudRate
  Baud Rate for Serial Debug Messages. 3:9600, 4:19200, 6:56700, 7:115200.
  3:9600, 4:19200, 6:56700, 7:115200
**/
  UINT8                       PcdSerialDebugBaudRate;

/** Offset 0x0A33 - HobBufferSize
  Size to set HOB Buffer. 0:Default, 1: 1 Byte, 2: 1 KB, 3: Max value(assuming 63KB
  total HOB size).
  0:Default, 1: 1 Byte, 2: 1 KB, 3: Max value
**/
  UINT8                       HobBufferSize;

/** Offset 0x0A34 - Early Command Training
  Enables/Disable Early Command Training
  $EN_DIS
**/
  UINT8                       ECT;

/** Offset 0x0A35 - SenseAmp Offset Training
  Enables/Disable SenseAmp Offset Training
  $EN_DIS
**/
  UINT8                       SOT;

/** Offset 0x0A36 - Early ReadMPR Timing Centering 2D
  Enables/Disable Early ReadMPR Timing Centering 2D
  $EN_DIS
**/
  UINT8                       ERDMPRTC2D;

/** Offset 0x0A37 - Read MPR Training
  Enables/Disable Read MPR Training
  $EN_DIS
**/
  UINT8                       RDMPRT;

/** Offset 0x0A38 - Receive Enable Training
  Enables/Disable Receive Enable Training
  $EN_DIS
**/
  UINT8                       RCVET;

/** Offset 0x0A39 - Jedec Write Leveling
  Enables/Disable Jedec Write Leveling
  $EN_DIS
**/
  UINT8                       JWRL;

/** Offset 0x0A3A - Early Write Time Centering 2D
  Enables/Disable Early Write Time Centering 2D
  $EN_DIS
**/
  UINT8                       EWRTC2D;

/** Offset 0x0A3B - Early Read Time Centering 2D
  Enables/Disable Early Read Time Centering 2D
  $EN_DIS
**/
  UINT8                       ERDTC2D;

/** Offset 0x0A3C - Reserved
**/
  UINT8                       Reserved46;

/** Offset 0x0A3D - Write Timing Centering 1D
  Enables/Disable Write Timing Centering 1D
  $EN_DIS
**/
  UINT8                       WRTC1D;

/** Offset 0x0A3E - Write Voltage Centering 1D
  Enables/Disable Write Voltage Centering 1D
  $EN_DIS
**/
  UINT8                       WRVC1D;

/** Offset 0x0A3F - Read Timing Centering 1D
  Enables/Disable Read Timing Centering 1D
  $EN_DIS
**/
  UINT8                       RDTC1D;

/** Offset 0x0A40 - Read Voltage Centering 1D
  Enable/Disable Read Voltage Centering 1D
  $EN_DIS
**/
  UINT8                       RDVC1D;

/** Offset 0x0A41 - Reserved
**/
  UINT8                       Reserved47[2];

/** Offset 0x0A43 - Read ODT Training
  Enables/Disable Read ODT Training
  $EN_DIS
**/
  UINT8                       RDODTT;

/** Offset 0x0A44 - Read Equalization Training
  Enables/Disable Read Equalization Training
  $EN_DIS
**/
  UINT8                       RDEQT;

/** Offset 0x0A45 - Reserved
**/
  UINT8                       Reserved48;

/** Offset 0x0A46 - Write Timing Centering 2D
  Enables/Disable Write Timing Centering 2D
  $EN_DIS
**/
  UINT8                       WRTC2D;

/** Offset 0x0A47 - Read Timing Centering 2D
  Enables/Disable Read Timing Centering 2D
  $EN_DIS
**/
  UINT8                       RDTC2D;

/** Offset 0x0A48 - Write Voltage Centering 2D
  Enables/Disable Write Voltage Centering 2D
  $EN_DIS
**/
  UINT8                       WRVC2D;

/** Offset 0x0A49 - Read Voltage Centering 2D
  Enables/Disable Read Voltage Centering 2D
  $EN_DIS
**/
  UINT8                       RDVC2D;

/** Offset 0x0A4A - Reserved
**/
  UINT8                       Reserved49;

/** Offset 0x0A4B - Command Voltage Centering
  Enables/Disable Command Voltage Centering
  $EN_DIS
**/
  UINT8                       CMDVC;

/** Offset 0x0A4C - Late Command Training
  Enables/Disable Late Command Training
  $EN_DIS
**/
  UINT8                       LCT;

/** Offset 0x0A4D - Turn Around Timing Training
  Enables/Disable Turn Around Timing Training
  $EN_DIS
**/
  UINT8                       TAT;

/** Offset 0x0A4E - Rank Margin Tool
  Enable/disable Rank Margin Tool
  $EN_DIS
**/
  UINT8                       RMT;

/** Offset 0x0A4F - Reserved
**/
  UINT8                       Reserved50;

/** Offset 0x0A50 - DIMM SPD Alias Test
  Enables/Disable DIMM SPD Alias Test
  $EN_DIS
**/
  UINT8                       ALIASCHK;

/** Offset 0x0A51 - Retrain Margin Check
  Enables/Disable Retrain Margin Check
  $EN_DIS
**/
  UINT8                       RMC;

/** Offset 0x0A52 - Reserved
**/
  UINT8                       Reserved51;

/** Offset 0x0A53 - Dimm ODT Training
  Enables/Disable Dimm ODT Training
  $EN_DIS
**/
  UINT8                       DIMMODTT;

/** Offset 0x0A54 - DIMM RON Training
  Enables/Disable DIMM RON Training
  $EN_DIS
**/
  UINT8                       DIMMRONT;

/** Offset 0x0A55 - TxDqTCO Comp Training
  Enable/Disable TxDqTCO Comp Training
  $EN_DIS
**/
  UINT8                       TXTCO;

/** Offset 0x0A56 - ClkTCO Comp Training
  Enable/Disable ClkTCO Comp Training
  $EN_DIS
**/
  UINT8                       CLKTCO;

/** Offset 0x0A57 - CMD Slew Rate Training
  Enable/Disable CMD Slew Rate Training
  $EN_DIS
**/
  UINT8                       CMDSR;

/** Offset 0x0A58 - Reserved
**/
  UINT8                       Reserved52[2];

/** Offset 0x0A5A - DIMM CA ODT Training
  Enable/Disable DIMM CA ODT Training
  $EN_DIS
**/
  UINT8                       DIMMODTCA;

/** Offset 0x0A5B - Reserved
**/
  UINT8                       Reserved53[3];

/** Offset 0x0A5E - Read Vref Decap Training
  Enable/Disable Read Vref Decap Training
  $EN_DIS
**/
  UINT8                       RDVREFDC;

/** Offset 0x0A5F - Vddq Training
  Enable/Disable Vddq Training
  $EN_DIS
**/
  UINT8                       VDDQT;

/** Offset 0x0A60 - Rank Margin Tool Per Bit
  Enable/Disable Rank Margin Tool Per Bit
  $EN_DIS
**/
  UINT8                       RMTBIT;

/** Offset 0x0A61 - Reserved
**/
  UINT8                       Reserved54[4];

/** Offset 0x0A65 - Duty Cycle Correction Training
  Enable/Disable Duty Cycle Correction Training
  $EN_DIS
**/
  UINT8                       DCC;

/** Offset 0x0A66 - Reserved
**/
  UINT8                       Reserved55[17];

/** Offset 0x0A77 - ECC Support
  Enables/Disable ECC Support
  $EN_DIS
**/
  UINT8                       EccSupport;

/** Offset 0x0A78 - Ibecc
  In-Band ECC Support
  $EN_DIS
**/
  UINT8                       Ibecc;

/** Offset 0x0A79 - IbeccParity
  In-Band ECC Parity Control
  $EN_DIS
**/
  UINT8                       IbeccParity;

/** Offset 0x0A7A - IbeccOperationMode
  In-Band ECC Operation Mode
  0:Protect base on address range, 1: Non-protected, 2: All protected
**/
  UINT8                       IbeccOperationMode;

/** Offset 0x0A7B - IbeccProtectedRegionEnable
  In-Band ECC Protected Region Enable
  $EN_DIS
**/
  UINT8                       IbeccProtectedRegionEnable[8];

/** Offset 0x0A83 - Reserved
**/
  UINT8                       Reserved56;

/** Offset 0x0A84 - IbeccProtectedRegionBases
  IBECC Protected Region Bases per IBECC instance
**/
  UINT16                      IbeccProtectedRegionBase[8];

/** Offset 0x0A94 - IbeccProtectedRegionMasks
  IBECC Protected Region Masks
**/
  UINT16                      IbeccProtectedRegionMask[8];

/** Offset 0x0AA4 - IbeccProtectedRegionOverallBases
  IBECC Protected Region Bases based on enabled IBECC instance
**/
  UINT16                      IbeccProtectedRegionOverallBase[8];

/** Offset 0x0AB4 - Memory Remap
  Enables/Disable Memory Remap
  $EN_DIS
**/
  UINT8                       RemapEnable;

/** Offset 0x0AB5 - Rank Interleave support
  Enables/Disable Rank Interleave support. NOTE: RI and HORI can not be enabled at
  the same time.
  $EN_DIS
**/
  UINT8                       RankInterleave;

/** Offset 0x0AB6 - Enhanced Interleave support
  Enables/Disable Enhanced Interleave support
  $EN_DIS
**/
  UINT8                       EnhancedInterleave;

/** Offset 0x0AB7 - Ch Hash Support
  Enable/Disable Channel Hash Support. NOTE: ONLY if Memory interleaved Mode
  $EN_DIS
**/
  UINT8                       ChHashEnable;

/** Offset 0x0AB8 - Extern Therm Status
  Enables/Disable Extern Therm Status
  $EN_DIS
**/
  UINT8                       EnableExtts;

/** Offset 0x0AB9 - DDR PowerDown and idle counter
  Enables/Disable DDR PowerDown and idle counter(For LPDDR Only)
  $EN_DIS
**/
  UINT8                       EnablePwrDn;

/** Offset 0x0ABA - DDR PowerDown and idle counter
  Enables/Disable DDR PowerDown and idle counter(For LPDDR Only)
  $EN_DIS
**/
  UINT8                       EnablePwrDnLpddr;

/** Offset 0x0ABB - SelfRefresh Enable
  Enables/Disable SelfRefresh Enable
  $EN_DIS
**/
  UINT8                       SrefCfgEna;

/** Offset 0x0ABC - Throttler CKEMin Defeature
  Enables/Disable Throttler CKEMin Defeature(For LPDDR Only)
  $EN_DIS
**/
  UINT8                       ThrtCkeMinDefeatLpddr;

/** Offset 0x0ABD - Throttler CKEMin Defeature
  Enables/Disable Throttler CKEMin Defeature
  $EN_DIS
**/
  UINT8                       ThrtCkeMinDefeat;

/** Offset 0x0ABE - Reserved
**/
  UINT8                       Reserved57;

/** Offset 0x0ABF - Exit On Failure (MRC)
  Enables/Disable Exit On Failure (MRC)
  $EN_DIS
**/
  UINT8                       ExitOnFailure;

/** Offset 0x0AC0 - Reserved
**/
  UINT8                       Reserved58[4];

/** Offset 0x0AC4 - Select if ZQ pin is shared between Rank0 and Rank1 in DDR4 DDP
  ESelect if ZQ pin is shared between Rank0 and Rank1 in DDR4 DDP
  $EN_DIS
**/
  UINT8                       Ddr4DdpSharedZq;

/** Offset 0x0AC5 - Ch Hash Interleaved Bit
  Select the BIT to be used for Channel Interleaved mode. NOTE: BIT7 will interlave
  the channels at a 2 cacheline granularity, BIT8 at 4 and BIT9 at 8. Default is BIT8
  0:BIT6, 1:BIT7, 2:BIT8, 3:BIT9, 4:BIT10, 5:BIT11, 6:BIT12, 7:BIT13
**/
  UINT8                       ChHashInterleaveBit;

/** Offset 0x0AC6 - Ch Hash Mask
  Set the BIT(s) to be included in the XOR function. NOTE BIT mask corresponds to
  BITS [19:6] Default is 0x30CC
**/
  UINT16                      ChHashMask;

/** Offset 0x0AC8 - Base reference clock value
  Base reference clock value, in Hertz(Default is 125Hz)
  100000000:100Hz, 125000000:125Hz, 167000000:167Hz, 250000000:250Hz
**/
  UINT32                      BClkFrequency;

/** Offset 0x0ACC - EPG DIMM Idd3N
  Active standby current (Idd3N) in milliamps from datasheet. Must be calculated on
  a per DIMM basis. Default is 26
**/
  UINT16                      Idd3n;

/** Offset 0x0ACE - EPG DIMM Idd3P
  Active power-down current (Idd3P) in milliamps from datasheet. Must be calculated
  on a per DIMM basis. Default is 11
**/
  UINT16                      Idd3p;

/** Offset 0x0AD0 - CMD Normalization
  Enable/Disable CMD Normalization
  $EN_DIS
**/
  UINT8                       CMDNORM;

/** Offset 0x0AD1 - Early DQ Write Drive Strength and Equalization Training
  Enable/Disable Early DQ Write Drive Strength and Equalization Training
  $EN_DIS
**/
  UINT8                       EWRDSEQ;

/** Offset 0x0AD2 - Idle Energy Mc0Ch0Dimm0
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc0Ch0Dimm0;

/** Offset 0x0AD3 - Idle Energy Mc0Ch0Dimm1
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc0Ch0Dimm1;

/** Offset 0x0AD4 - Idle Energy Mc0Ch1Dimm0
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc0Ch1Dimm0;

/** Offset 0x0AD5 - Idle Energy Mc0Ch1Dimm1
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc0Ch1Dimm1;

/** Offset 0x0AD6 - Idle Energy Mc1Ch0Dimm0
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc1Ch0Dimm0;

/** Offset 0x0AD7 - Idle Energy Mc1Ch0Dimm1
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc1Ch0Dimm1;

/** Offset 0x0AD8 - Idle Energy Mc1Ch1Dimm0
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc1Ch1Dimm0;

/** Offset 0x0AD9 - Idle Energy Mc1Ch1Dimm1
  Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
  UINT8                       IdleEnergyMc1Ch1Dimm1;

/** Offset 0x0ADA - PowerDown Energy Mc0Ch0Dimm0
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc0Ch0Dimm0;

/** Offset 0x0ADB - PowerDown Energy Mc0Ch0Dimm1
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc0Ch0Dimm1;

/** Offset 0x0ADC - PowerDown Energy Mc0Ch1Dimm0
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc0Ch1Dimm0;

/** Offset 0x0ADD - PowerDown Energy Mc0Ch1Dimm1
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc0Ch1Dimm1;

/** Offset 0x0ADE - PowerDown Energy Mc1Ch0Dimm0
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc1Ch0Dimm0;

/** Offset 0x0ADF - PowerDown Energy Mc1Ch0Dimm1
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc1Ch0Dimm1;

/** Offset 0x0AE0 - PowerDown Energy Mc1Ch1Dimm0
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc1Ch1Dimm0;

/** Offset 0x0AE1 - PowerDown Energy Mc1Ch1Dimm1
  PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
  UINT8                       PdEnergyMc1Ch1Dimm1;

/** Offset 0x0AE2 - Activate Energy Mc0Ch0Dimm0
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc0Ch0Dimm0;

/** Offset 0x0AE3 - Activate Energy Mc0Ch0Dimm1
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc0Ch0Dimm1;

/** Offset 0x0AE4 - Activate Energy Mc0Ch1Dimm0
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc0Ch1Dimm0;

/** Offset 0x0AE5 - Activate Energy Mc0Ch1Dimm1
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc0Ch1Dimm1;

/** Offset 0x0AE6 - Activate Energy Mc1Ch0Dimm0
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc1Ch0Dimm0;

/** Offset 0x0AE7 - Activate Energy Mc1Ch0Dimm1
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc1Ch0Dimm1;

/** Offset 0x0AE8 - Activate Energy Mc1Ch1Dimm0
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc1Ch1Dimm0;

/** Offset 0x0AE9 - Activate Energy Mc1Ch1Dimm1
  Activate Energy Contribution, range[255;0],(172= Def)
**/
  UINT8                       ActEnergyMc1Ch1Dimm1;

/** Offset 0x0AEA - Read Energy Mc0Ch0Dimm0
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc0Ch0Dimm0;

/** Offset 0x0AEB - Read Energy Mc0Ch0Dimm1
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc0Ch0Dimm1;

/** Offset 0x0AEC - Read Energy Mc0Ch1Dimm0
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc0Ch1Dimm0;

/** Offset 0x0AED - Read Energy Mc0Ch1Dimm1
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc0Ch1Dimm1;

/** Offset 0x0AEE - Read Energy Mc1Ch0Dimm0
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc1Ch0Dimm0;

/** Offset 0x0AEF - Read Energy Mc1Ch0Dimm1
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc1Ch0Dimm1;

/** Offset 0x0AF0 - Read Energy Mc1Ch1Dimm0
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc1Ch1Dimm0;

/** Offset 0x0AF1 - Read Energy Mc1Ch1Dimm1
  Read Energy Contribution, range[255;0],(212= Def)
**/
  UINT8                       RdEnergyMc1Ch1Dimm1;

/** Offset 0x0AF2 - Write Energy Mc0Ch0Dimm0
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc0Ch0Dimm0;

/** Offset 0x0AF3 - Write Energy Mc0Ch0Dimm1
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc0Ch0Dimm1;

/** Offset 0x0AF4 - Write Energy Mc0Ch1Dimm0
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc0Ch1Dimm0;

/** Offset 0x0AF5 - Write Energy Mc0Ch1Dimm1
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc0Ch1Dimm1;

/** Offset 0x0AF6 - Write Energy Mc1Ch0Dimm0
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc1Ch0Dimm0;

/** Offset 0x0AF7 - Write Energy Mc1Ch0Dimm1
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc1Ch0Dimm1;

/** Offset 0x0AF8 - Write Energy Mc1Ch1Dimm0
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc1Ch1Dimm0;

/** Offset 0x0AF9 - Write Energy Mc1Ch1Dimm1
  Write Energy Contribution, range[255;0],(221= Def)
**/
  UINT8                       WrEnergyMc1Ch1Dimm1;

/** Offset 0x0AFA - Throttler CKEMin Timer
  Timer value for CKEMin, range[255;0]. Req'd min of SC_ROUND_T + BYTE_LENGTH (4).
  Dfault is 0x00
**/
  UINT8                       ThrtCkeMinTmr;

/** Offset 0x0AFB - Reserved
**/
  UINT8                       Reserved59[2];

/** Offset 0x0AFD - Rapl Power Floor Ch0
  Power budget ,range[255;0],(0= 5.3W Def)
**/
  UINT8                       RaplPwrFlCh0;

/** Offset 0x0AFE - Rapl Power Floor Ch1
  Power budget ,range[255;0],(0= 5.3W Def)
**/
  UINT8                       RaplPwrFlCh1;

/** Offset 0x0AFF - Command Rate Support
  CMD Rate and Limit Support Option. NOTE: ONLY supported in 1N Mode, Default is 3 CMDs
  0:Disable, 5:2 CMDS, 7:3 CMDS, 9:4 CMDS, 11:5 CMDS, 13:6 CMDS, 15:7 CMDS
**/
  UINT8                       EnCmdRate;

/** Offset 0x0B00 - Reserved
**/
  UINT8                       Reserved60;

/** Offset 0x0B01 - Energy Performance Gain
  Enable/disable Energy Performance Gain. <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       EpgEnable;

/** Offset 0x0B02 - Reserved
**/
  UINT8                       Reserved61;

/** Offset 0x0B03 - User Manual Threshold
  Disabled: Predefined threshold will be used.\n
  Enabled: User Input will be used.
  $EN_DIS
**/
  UINT8                       UserThresholdEnable;

/** Offset 0x0B04 - User Manual Budget
  Disabled: Configuration of memories will defined the Budget value.\n
  Enabled: User Input will be used.
  $EN_DIS
**/
  UINT8                       UserBudgetEnable;

/** Offset 0x0B05 - Power Down Mode
  This option controls command bus tristating during idle periods
  0x0:No Power Down, 0x1:APD, 0x6:PPD DLL OFF, 0xFF:Auto
**/
  UINT8                       PowerDownMode;

/** Offset 0x0B06 - Pwr Down Idle Timer
  The minimum value should = to the worst case Roundtrip delay + Burst_Length. 0 means
  AUTO: 64 for ULX/ULT, 128 for DT/Halo
**/
  UINT8                       PwdwnIdleCounter;

/** Offset 0x0B07 - Page Close Idle Timeout
  This option controls Page Close Idle Timeout
  0:Enabled, 1:Disabled
**/
  UINT8                       DisPgCloseIdleTimeout;

/** Offset 0x0B08 - Bitmask of ranks that have CA bus terminated
  Offset 225 LPDDR4: Bitmask of ranks that have CA bus terminated. <b>0x01=Default,
  Rank0 is terminating and Rank1 is non-terminating</b>
**/
  UINT8                       CmdRanksTerminated;

/** Offset 0x0B09 - PcdSerialDebugLevel
  Serial Debug Message Level. 0:Disable, 1:Error Only, 2:Error & Warnings, 3:Load,
  Error, Warnings & Info, 4:Load, Error, Warnings, Info & Event, 5:Load, Error, Warnings,
  Info & Verbose.
  0:Disable, 1:Error Only, 2:Error and Warnings, 3:Load Error Warnings and Info, 4:Load
  Error Warnings and Info & Event, 5:Load Error Warnings Info and Verbose
**/
  UINT8                       PcdSerialDebugLevel;

/** Offset 0x0B0A - Reserved
**/
  UINT8                       Reserved62[7];

/** Offset 0x0B11 - Ask MRC to clear memory content
  Ask MRC to clear memory content <b>0: Do not Clear Memory;</b> 1: Clear Memory.
  $EN_DIS
**/
  UINT8                       CleanMemory;

/** Offset 0x0B12 - TCSS USB Port Enable
  Bitmap for per port enabling
**/
  UINT8                       UsbTcPortEnPreMem;

/** Offset 0x0B13 - Reserved
**/
  UINT8                       Reserved63;

/** Offset 0x0B14 - Post Code Output Port
  This option configures Post Code Output Port
**/
  UINT16                      PostCodeOutputPort;

/** Offset 0x0B16 - RMTLoopCount
  Specifies the Loop Count to be used during Rank Margin Tool Testing. 0 - AUTO
**/
  UINT8                       RMTLoopCount;

/** Offset 0x0B17 - Enable/Disable SA CRID
  Enable: SA CRID, Disable (Default): SA CRID
  $EN_DIS
**/
  UINT8                       CridEnable;

/** Offset 0x0B18 - BCLK RFI Frequency
  Bclk RFI Frequency for each SAGV point in Hz units. 98000000Hz = 98MHz <b>0 - No
  RFI Tuning</b>. Range is 98Mhz-100Mhz.
**/
  UINT32                      BclkRfiFreq[4];

/** Offset 0x0B28 - Size of PCIe IMR.
  Size of PCIe IMR in megabytes
**/
  UINT16                      PcieImrSize;

/** Offset 0x0B2A - Enable PCIe IMR
  0: Disable(AUTO), 1: Enable
  $EN_DIS
**/
  UINT8                       PcieImrEnabled;

/** Offset 0x0B2B - Enable PCIe IMR
  1: PCH PCIE, 2: SA PCIE. If PCIeImrEnabled is TRUE then this will use to select
  the Root port location from PCH PCIe or SA PCIe
  $EN_DIS
**/
  UINT8                       PcieImrRpLocation;

/** Offset 0x0B2C - Root port number for IMR.
  Root port number for IMR.If PCieImrRpLocation is PCH PCIe then select root port
  from 0 to 23 and if it is SA PCIe then select root port from 0 to 3
**/
  UINT8                       PcieImrRpSelection;

/** Offset 0x0B2D - SerialDebugMrcLevel
  MRC Serial Debug Message Level. 0:Disable, 1:Error Only, 2:Error & Warnings, 3:Load,
  Error, Warnings & Info, 4:Load, Error, Warnings, Info & Event, 5:Load, Error, Warnings,
  Info & Verbose.
  0:Disable, 1:Error Only, 2:Error and Warnings, 3:Load Error Warnings and Info, 4:Load
  Error Warnings and Info & Event, 5:Load Error Warnings Info and Verbose
**/
  UINT8                       SerialDebugMrcLevel;

/** Offset 0x0B2E - Reserved
**/
  UINT8                       Reserved64[13];

/** Offset 0x0B3B - Command Pins Mapping
  BitMask where bits [3:0] are Controller 0 Channel [3:0] and bits [7:4] are Controller
  1 Channel [3:0]. 0 = CCC pin mapping is Ascending, 1 = CCC pin mapping is Descending.
**/
  UINT8                       Lp5CccConfig;

/** Offset 0x0B3C - Command Pins Mirrored
  BitMask where bits [3:0] are Controller 0 Channel [3:0] and bits [7:4] are Controller
  1 Channel [3:0]. 0 = No Command Mirror and 1 = Command Mirror.
**/
  UINT8                       CmdMirror;

/** Offset 0x0B3D - Reserved
**/
  UINT8                       Reserved65[4];

/** Offset 0x0B41 - Skip external display device scanning
  Enable: Do not scan for external display device, Disable (Default): Scan external
  display devices
  $EN_DIS
**/
  UINT8                       SkipExtGfxScan;

/** Offset 0x0B42 - Generate BIOS Data ACPI Table
  Enable: Generate BDAT for MRC RMT or SA PCIe data. Disable (Default): Do not generate it
  $EN_DIS
**/
  UINT8                       BdatEnable;

/** Offset 0x0B43 - Lock PCU Thermal Management registers
  Lock PCU Thermal Management registers. Enable(Default)=1, Disable=0
  $EN_DIS
**/
  UINT8                       LockPTMregs;

/** Offset 0x0B44 - Panel Power Enable
  Control for enabling/disabling VDD force bit (Required only for early enabling of
  eDP panel). 0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       PanelPowerEnable;

/** Offset 0x0B45 - BdatTestType
  Indicates the type of Memory Training data to populate into the BDAT ACPI table.
  0:RMT per Rank, 1:RMT per Bit, 2:Margin2D
**/
  UINT8                       BdatTestType;

/** Offset 0x0B46 - Reserved
**/
  UINT8                       Reserved66[2];

/** Offset 0x0B48 - PMR Size
  Size of PMR memory buffer. 0x400000 for normal boot and 0x200000 for S3 boot
**/
  UINT32                      DmaBufferSize;

/** Offset 0x0B4C - The policy for VTd driver behavior
  BIT0: Enable IOMMU during boot, BIT1: Enable IOMMU when transfer control to OS
**/
  UINT8                       PreBootDmaMask;

/** Offset 0x0B4D - Reserved
**/
  UINT8                       Reserved67[95];

/** Offset 0x0BAC - TotalFlashSize
  Enable/Disable. 0: Disable, define default value of TotalFlashSize , 1: enable
**/
  UINT16                      TotalFlashSize;

/** Offset 0x0BAE - BiosSize
  The size of the BIOS region of the IFWI. Used if FspmUpd->FspmConfig.BiosGuard !=
  0. If BiosGuard is enabled, MRC will increase the size of the DPR (DMA Protected
  Range) so that a BIOS Update Script can be stored in the DPR.
**/
  UINT16                      BiosSize;

/** Offset 0x0BB0 - Reserved
**/
  UINT8                       Reserved68[12];

/** Offset 0x0BBC - Smbus dynamic power gating
  Disable or Enable Smbus dynamic power gating.
  $EN_DIS
**/
  UINT8                       SmbusDynamicPowerGating;

/** Offset 0x0BBD - Disable and Lock Watch Dog Register
  Set 1 to clear WDT status, then disable and lock WDT registers.
  $EN_DIS
**/
  UINT8                       WdtDisableAndLock;

/** Offset 0x0BBE - SMBUS SPD Write Disable
  Set/Clear Smbus SPD Write Disable. 0: leave SPD Write Disable bit; 1: set SPD Write
  Disable bit. For security recommendations, SPD write disable bit must be set.
  $EN_DIS
**/
  UINT8                       SmbusSpdWriteDisable;

/** Offset 0x0BBF - Reserved
**/
  UINT8                       Reserved69[34];

/** Offset 0x0BE1 - HECI Timeouts
  0: Disable, 1: Enable (Default) timeout check for HECI
  $EN_DIS
**/
  UINT8                       HeciTimeouts;

/** Offset 0x0BE2 - Force ME DID Init Status
  Test, 0: disable, 1: Success, 2: No Memory in Channels, 3: Memory Init Error, Set
  ME DID init stat value
  $EN_DIS
**/
  UINT8                       DidInitStat;

/** Offset 0x0BE3 - CPU Replaced Polling Disable
  Test, 0: disable, 1: enable, Setting this option disables CPU replacement polling loop
  $EN_DIS
**/
  UINT8                       DisableCpuReplacedPolling;

/** Offset 0x0BE4 - Check HECI message before send
  Test, 0: disable, 1: enable, Enable/Disable message check.
  $EN_DIS
**/
  UINT8                       DisableMessageCheck;

/** Offset 0x0BE5 - Skip MBP HOB
  Test, 0: disable, 1: enable, Enable/Disable MOB HOB.
  $EN_DIS
**/
  UINT8                       SkipMbpHob;

/** Offset 0x0BE6 - HECI2 Interface Communication
  Test, 0: disable, 1: enable, Adds or Removes HECI2 Device from PCI space.
  $EN_DIS
**/
  UINT8                       HeciCommunication2;

/** Offset 0x0BE7 - Enable KT device
  Test, 0: disable, 1: enable, Enable or Disable KT device.
  $EN_DIS
**/
  UINT8                       KtDeviceEnable;

/** Offset 0x0BE8 - Skip CPU replacement check
  Test, 0: disable, 1: enable, Setting this option to skip CPU replacement check
  $EN_DIS
**/
  UINT8                       SkipCpuReplacementCheck;

/** Offset 0x0BE9 - Avx2 Voltage Guardband Scaling Factor
  AVX2 Voltage Guardband Scale factor applied to AVX2 workloads. Range is 0-200 in
  1/100 units, where a value of 125 would apply a 1.25 scale factor.
**/
  UINT8                       Avx2VoltageScaleFactor;

/** Offset 0x0BEA - Avx512 Voltage Guardband Scaling Factor
  AVX512 Voltage Guardband Scale factor applied to AVX512 workloads. Range is 0-200
  in 1/100 units, where a value of 125 would apply a 1.25 scale factor.
**/
  UINT8                       Avx512VoltageScaleFactor;

/** Offset 0x0BEB - Serial Io Uart Debug Mode
  Select SerialIo Uart Controller mode
  0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
  4:SerialIoUartSkipInit
**/
  UINT8                       SerialIoUartDebugMode;

/** Offset 0x0BEC - SerialIoUartDebugRxPinMux - FSPM
  Select RX pin muxing for SerialIo UART used for debug
**/
  UINT32                      SerialIoUartDebugRxPinMux;

/** Offset 0x0BF0 - SerialIoUartDebugTxPinMux - FSPM
  Select TX pin muxing for SerialIo UART used for debug
**/
  UINT32                      SerialIoUartDebugTxPinMux;

/** Offset 0x0BF4 - SerialIoUartDebugRtsPinMux - FSPM
  Select SerialIo Uart used for debug Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
  for possible values.
**/
  UINT32                      SerialIoUartDebugRtsPinMux;

/** Offset 0x0BF8 - SerialIoUartDebugCtsPinMux - FSPM
  Select SerialIo Uart used for debug Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
  for possible values.
**/
  UINT32                      SerialIoUartDebugCtsPinMux;

/** Offset 0x0BFC - Reserved
**/
  UINT8                      Reserved70[20];
} FSP_M_CONFIG;

/** Fsp M UPD Configuration
**/
typedef struct {

/** Offset 0x0000
**/
  FSP_UPD_HEADER              FspUpdHeader;

/** Offset 0x0020
**/
  FSPM_ARCH_UPD               FspmArchUpd;

/** Offset 0x0040
**/
  FSP_M_CONFIG                FspmConfig;

/** Offset 0x0C10
**/
  UINT8                       Rsvd500[6];

/** Offset 0x0C16
**/
  UINT16                      UpdTerminator;
} FSPM_UPD;

#pragma pack()

#endif