mb/intel/kblrvp: Enable Kabylake RVP8
Add support for KBL RVP8 board
* Add KBL RVP8 support in Konfig.
* Add KBL RVP8 config option in make menuconfig.
* Add descriptor and ME binary paths for RVP8 in Kconfig.
* Add RVP8 board name Kconfig.name.
* Add devicetree.cb for RVP8 in the variants path.
* Add gpio.h for RVP8 in variants/include/variant path.
TEST= Build and boot RVP8.
Change-Id: I6ba177c223f6aa3285c0fe5eba0cd55b2a50c4ed
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/23383
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
diff --git a/src/mainboard/intel/kblrvp/variants/rvp8/devicetree.cb b/src/mainboard/intel/kblrvp/variants/rvp8/devicetree.cb
new file mode 100644
index 0000000..2a2d761
--- /dev/null
+++ b/src/mainboard/intel/kblrvp/variants/rvp8/devicetree.cb
@@ -0,0 +1,272 @@
+chip soc/intel/skylake
+
+ # Enable deep Sx states
+ register "deep_s3_enable_ac" = "0"
+ register "deep_s3_enable_dc" = "0"
+ register "deep_s5_enable_ac" = "0"
+ register "deep_s5_enable_dc" = "0"
+ register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"
+
+ # GPE configuration
+ # Note that GPE events called out in ASL code rely on this
+ # route. i.e. If this route changes then the affected GPE
+ # offset bits also need to be changed.
+ register "gpe0_dw0" = "GPP_B"
+ register "gpe0_dw1" = "GPP_D"
+ register "gpe0_dw2" = "GPP_E"
+
+ # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
+ register "gen1_dec" = "0x00fc0801"
+
+ # Enable "Intel Speed Shift Technology"
+ register "speed_shift_enable" = "1"
+
+ # Enable DPTF
+ register "dptf_enable" = "1"
+
+ # FSP Configuration
+ register "SmbusEnable" = "1"
+ register "ScsEmmcEnabled" = "0"
+ register "ScsEmmcHs400Enabled" = "0"
+ register "ScsSdCardEnabled" = "0"
+ register "InternalGfx" = "1"
+ register "SkipExtGfxScan" = "1"
+ register "Device4Enable" = "1"
+ register "HeciEnabled" = "0"
+ register "SaGv" = "3"
+ register "PmTimerDisabled" = "0"
+
+ register "pirqa_routing" = "PCH_IRQ11"
+ register "pirqb_routing" = "PCH_IRQ10"
+ register "pirqc_routing" = "PCH_IRQ11"
+ register "pirqd_routing" = "PCH_IRQ11"
+ register "pirqe_routing" = "PCH_IRQ11"
+ register "pirqf_routing" = "PCH_IRQ11"
+ register "pirqg_routing" = "PCH_IRQ11"
+ register "pirqh_routing" = "PCH_IRQ11"
+
+ # Enabling SLP_S3#, SLP_S4#, SLP_SUS and SLP_A Stretch
+ # SLP_S3 Minimum Assertion Width. Values 0: 60us, 1: 1ms, 2: 50ms, 3: 2s
+ register "PmConfigSlpS3MinAssert" = "0x02"
+
+ # SLP_S4 Minimum Assertion Width. Values 0: default, 1: 1s, 2: 2s, 3: 3s, 4: 4s
+ register "PmConfigSlpS4MinAssert" = "0x04"
+
+ # SLP_SUS Minimum Assertion Width. Values 0: 0ms, 1: 500ms, 2: 1s, 3: 4s
+ register "PmConfigSlpSusMinAssert" = "0x03"
+
+ # SLP_A Minimum Assertion Width. Values 0: 0ms, 1: 4s, 2: 98ms, 3: 2s
+ register "PmConfigSlpAMinAssert" = "0x03"
+
+ # Determines if enable Serial IRQ. Values 0: Disabled, 1: Enabled
+ register "SerialIrqConfigSirqEnable" = "0x01"
+ register "SerialIrqConfigSirqMode" = "0x01"
+
+ # VR Settings Configuration for 5 Domains
+ #+----------------+-------+-------+-------------+-------------+-------+
+ #| Domain/Setting | SA | IA | Ring Sliced | GT Unsliced | GT |
+ #+----------------+-------+-------+-------------+-------------+-------+
+ #| Psi1Threshold | 20A | 20A | 20A | 20A | 20A |
+ #| Psi2Threshold | 4A | 5A | 5A | 5A | 5A |
+ #| Psi3Threshold | 1A | 1A | 1A | 1A | 1A |
+ #| Psi3Enable | 1 | 1 | 1 | 1 | 1 |
+ #| Psi4Enable | 1 | 1 | 1 | 1 | 1 |
+ #| ImonSlope | 0 | 0 | 0 | 0 | 0 |
+ #| ImonOffset | 0 | 0 | 0 | 0 | 0 |
+ #| IccMax | 7A | 34A | 34A | 35A | 35A |
+ #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | 1.52V |
+ #+----------------+-------+-------+-------------+-------------+-------+
+ register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
+ .vr_config_enable = 1, \
+ .psi1threshold = 0x50, \
+ .psi2threshold = 0x10, \
+ .psi3threshold = 0x4, \
+ .psi3enable = 1, \
+ .psi4enable = 1, \
+ .imon_slope = 0x0, \
+ .imon_offset = 0x0, \
+ .icc_max = 0x0, \
+ .voltage_limit = 0x0 \
+ }"
+
+ register "domain_vr_config[VR_IA_CORE]" = "{
+ .vr_config_enable = 1, \
+ .psi1threshold = 0x50, \
+ .psi2threshold = 0x14, \
+ .psi3threshold = 0x4, \
+ .psi3enable = 1, \
+ .psi4enable = 1, \
+ .imon_slope = 0x0, \
+ .imon_offset = 0x0, \
+ .icc_max = 0x0, \
+ .voltage_limit = 0x0 \
+ }"
+
+ register "domain_vr_config[VR_GT_UNSLICED]" = "{
+ .vr_config_enable = 1, \
+ .psi1threshold = 0x50, \
+ .psi2threshold = 0x14, \
+ .psi3threshold = 0x4, \
+ .psi3enable = 1, \
+ .psi4enable = 1, \
+ .imon_slope = 0x0, \
+ .imon_offset = 0x0, \
+ .icc_max = 0x0 ,\
+ .voltage_limit = 0x0 \
+ }"
+
+ register "domain_vr_config[VR_GT_SLICED]" = "{
+ .vr_config_enable = 1, \
+ .psi1threshold = 0x50, \
+ .psi2threshold = 0x14, \
+ .psi3threshold = 0x4, \
+ .psi3enable = 1, \
+ .psi4enable = 1, \
+ .imon_slope = 0x0, \
+ .imon_offset = 0x0, \
+ .icc_max = 0x0, \
+ .voltage_limit = 0x0 \
+ }"
+
+ register "FspSkipMpInit" = "1"
+
+ # Enable Root port.
+ register "PcieRpEnable[3]" = "1"
+ register "PcieRpEnable[4]" = "1"
+ register "PcieRpEnable[8]" = "1"
+ register "PcieRpEnable[16]" = "1"
+
+ # Enable CLKREQ#
+ register "PcieRpClkReqSupport[3]" = "1"
+ register "PcieRpClkReqSupport[4]" = "1"
+ register "PcieRpClkReqSupport[8]" = "1"
+ register "PcieRpClkReqSupport[16]" = "1"
+
+ # SRCCLKREQ#
+ register "PcieRpClkReqNumber[3]" = "2"
+ register "PcieRpClkReqNumber[4]" = "1"
+ register "PcieRpClkReqNumber[8]" = "6"
+ register "PcieRpClkReqNumber[16]" = "7"
+
+ register "usb2_ports[0]" = "USB2_PORT_MAX(OC2)" # Type-C Port
+ register "usb2_ports[1]" = "USB2_PORT_MAX(OC5)" # Front panel
+ register "usb2_ports[2]" = "USB2_PORT_MAX(OC4)" # Back panel
+ register "usb2_ports[3]" = "USB2_PORT_MAX(OC4)" # Back panel
+ register "usb2_ports[4]" = "USB2_PORT_MAX(OC1)" # Back panel-1
+ register "usb2_ports[5]" = "USB2_PORT_MAX(OC1)" # Back panel
+ register "usb2_ports[6]" = "USB2_PORT_MAX(OC_SKIP)" # Back panel
+ register "usb2_ports[7]" = "USB2_PORT_MAX(OC_SKIP)" # Front panel
+ register "usb2_ports[8]" = "USB2_PORT_MAX(OC_SKIP)" # M.2 BT
+ register "usb2_ports[9]" = "USB2_PORT_MAX(OC2)" # Front panel
+ register "usb2_ports[10]" = "USB2_PORT_MAX(OC_SKIP)" # Back panel
+ register "usb2_ports[11]" = "USB2_PORT_MAX(OC_SKIP)" # Back panel-1
+ register "usb2_ports[12]" = "USB2_PORT_MAX(OC3)" # Back panel
+ register "usb2_ports[13]" = "USB2_PORT_MAX(OC_SKIP)" # Back panel
+
+ register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port
+ register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC1)" # Back panel
+ register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC1)" # Back panel
+ register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC0)" # Back panel-2
+ register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC0)" # Front Panel
+ register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Front Panel
+ register "usb3_ports[6]" = "USB3_PORT_DEFAULT(OC2)" # Front Panel
+ register "usb3_ports[7]" = "USB3_PORT_DEFAULT(OC2)" # Front Panel
+ register "usb3_ports[8]" = "USB3_PORT_DEFAULT(OC3)" # Back panel
+ register "usb3_ports[9]" = "USB3_PORT_DEFAULT(OC_SKIP)" # LAN
+
+ register "SsicPortEnable" = "1" # Enable SSIC for WWAN
+
+ register "EnableSata" = "1"
+ register "SataSalpSupport" = "1"
+ register "SataPortsEnable" = "{ \
+ [0] = 1, \
+ [1] = 1, \
+ [2] = 1, \
+ [3] = 1, \
+ [4] = 1, \
+ [5] = 1, \
+ [6] = 1, \
+ [7] = 1, \
+ }"
+
+ # Must leave UART0 enabled or SD/eMMC will not work as PCI
+ register "SerialIoDevMode" = "{ \
+ [PchSerialIoIndexI2C0] = PchSerialIoPci, \
+ [PchSerialIoIndexI2C1] = PchSerialIoPci, \
+ [PchSerialIoIndexI2C2] = PchSerialIoDisabled, \
+ [PchSerialIoIndexI2C3] = PchSerialIoDisabled, \
+ [PchSerialIoIndexI2C4] = PchSerialIoDisabled, \
+ [PchSerialIoIndexI2C5] = PchSerialIoDisabled, \
+ [PchSerialIoIndexSpi0] = PchSerialIoDisabled, \
+ [PchSerialIoIndexSpi1] = PchSerialIoDisabled, \
+ [PchSerialIoIndexUart0] = PchSerialIoPci, \
+ [PchSerialIoIndexUart1] = PchSerialIoDisabled, \
+ [PchSerialIoIndexUart2] = PchSerialIoLegacyUart, \
+ }"
+
+ # PL2 override 25W
+ register "tdp_pl2_override" = "25"
+
+ # Send an extra VR mailbox command for the PS4 exit issue
+ register "SendVrMbxCmd" = "2"
+
+ # Enable/Disable VMX feature
+ register "VmxEnable" = "0"
+
+ # Use default SD card detect GPIO configuration
+ #register "sdcard_cd_gpio_default" = "GPP_D10"
+
+ device cpu_cluster 0 on
+ device lapic 0 on end
+ end
+ device domain 0 on
+ device pci 00.0 on end # Host Bridge
+ device pci 02.0 on end # Integrated Graphics Device
+ device pci 14.0 on end # USB xHCI
+ device pci 14.1 off end # USB xDCI (OTG)
+ device pci 14.2 on end # Thermal Subsystem
+ device pci 15.0 on end # I2C #0
+ device pci 15.1 on end # I2C #1
+ device pci 15.2 on end # I2C #2
+ device pci 15.3 on end # I2C #3
+ device pci 16.0 on end # Management Engine Interface 1
+ device pci 16.1 off end # Management Engine Interface 2
+ device pci 16.2 off end # Management Engine IDE-R
+ device pci 16.3 off end # Management Engine KT Redirection
+ device pci 16.4 off end # Management Engine Interface 3
+ device pci 17.0 on end # SATA
+ device pci 19.0 on end # UART #2
+ device pci 19.1 on end # I2C #5
+ device pci 19.2 on end # I2C #4
+ device pci 1c.0 off end # PCI Express Port 1
+ device pci 1c.1 off end # PCI Express Port 2
+ device pci 1c.2 on end # PCI Express Port 3
+ device pci 1c.3 on end # PCI Express Port 4
+ device pci 1c.4 on end # PCI Express Port 5
+ device pci 1c.5 off end # PCI Express Port 6
+ device pci 1c.6 off end # PCI Express Port 7
+ device pci 1c.7 off end # PCI Express Port 8
+ device pci 1d.0 on end # PCI Express Port 9
+ device pci 1d.1 off end # PCI Express Port 10
+ device pci 1d.2 off end # PCI Express Port 11
+ device pci 1d.3 off end # PCI Express Port 12
+ device pci 1e.0 on end # UART #0
+ device pci 1e.1 on end # UART #1
+ device pci 1e.2 on end # GSPI #0
+ device pci 1e.3 on end # GSPI #1
+ device pci 1e.4 off end # eMMC
+ device pci 1e.5 off end # SDIO
+ device pci 1e.6 on end # SDCard
+ device pci 1f.0 on
+ #chip drivers/pc80/tpm
+ # device pnp 0c31.0 on end
+ #end
+ end # LPC Interface
+ device pci 1f.1 on end # P2SB
+ device pci 1f.2 on end # Power Management Controller
+ device pci 1f.3 on end # Intel HDA
+ device pci 1f.4 on end # SMBus
+ device pci 1f.5 on end # PCH SPI
+ device pci 1f.6 on end # GbE
+ end
+end