superio/nuvoton/nct5104d: add chip config option to reset GPIOs
Define a chip option to explicitly soft reset all enabled GPIOs to
default state.
TEST=boot FreeBSD 11.2 on PC Engines apu1, change GPIO configuration
using nctgpio module and check whether GPIOs are reset after reboot
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iae4205574800138402cbc95f4948167265a80d15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
diff --git a/src/superio/nuvoton/nct5104d/chip.h b/src/superio/nuvoton/nct5104d/chip.h
index 5b79037..ad1c302 100644
--- a/src/superio/nuvoton/nct5104d/chip.h
+++ b/src/superio/nuvoton/nct5104d/chip.h
@@ -6,6 +6,7 @@
struct superio_nuvoton_nct5104d_config {
u8 irq_trigger_type;
+ u8 reset_gpios;
};
#endif
diff --git a/src/superio/nuvoton/nct5104d/superio.c b/src/superio/nuvoton/nct5104d/superio.c
index e49a7cb..5570026 100644
--- a/src/superio/nuvoton/nct5104d/superio.c
+++ b/src/superio/nuvoton/nct5104d/superio.c
@@ -1,6 +1,7 @@
/* SPDX-License-Identifier: GPL-2.0-or-later */
/* This file is part of the coreboot project. */
+#include <stdlib.h>
#include <console/console.h>
#include <device/pnp.h>
#include <device/device.h>
@@ -98,42 +99,45 @@
static void reset_gpio_default_in(struct device *dev)
{
pnp_set_logical_device(dev);
-
- /* Soft reset GPIOs to default state: IN */
- switch (dev->path.pnp.device) {
- case NCT5104D_GPIO0:
- pnp_write_config(dev, NCT5104D_GPIO0_IO, 0xFF);
- break;
- case NCT5104D_GPIO1:
- pnp_write_config(dev, NCT5104D_GPIO1_IO, 0xFF);
- break;
- case NCT5104D_GPIO6:
- pnp_write_config(dev, NCT5104D_GPIO6_IO, 0xFF);
- break;
- default:
- break;
- }
+ /*
+ * Soft reset GPIOs to default state: IN.
+ * The main GPIO LDN holds registers that configure the pins as output
+ * or input. These registers are located at offset 0xE0 plus the GPIO
+ * bank number multiplied by 4: 0xE0 for GPIO0, 0xE4 for GPIO1 and
+ * 0xF8 for GPIO6.
+ */
+ pnp_write_config(dev, NCT5104D_GPIO0_IO + (dev->path.pnp.device >> 8) * 4, 0xFF);
}
static void reset_gpio_default_od(struct device *dev)
{
struct device *gpio0, *gpio1, *gpio6;
+ pnp_set_logical_device(dev);
+
gpio0 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO0);
gpio1 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO1);
gpio6 = dev_find_slot_pnp(dev->path.pnp.port, NCT5104D_GPIO6);
- pnp_set_logical_device(dev);
-
- /* Soft reset GPIOs to default state: Open-drain */
+ /*
+ * Soft reset GPIOs to default state: Open-drain.
+ * The NCT5104D_GPIO_PP_OD LDN holds registers (1 for each GPIO bank)
+ * that configure each GPIO pin to be open dain or push pull. System
+ * reset is known to not reset the values in this register. The
+ * registers are located at offsets begginign from 0xE0 plus GPIO bank
+ * number, i.e. 0xE0 for GPIO0, 0xE1 for GPIO1 and 0xE6 for GPIO6.
+ */
if (gpio0 && gpio0->enabled)
- pnp_write_config(dev, NCT5104D_GPIO0_PP_OD, 0xFF);
+ pnp_write_config(dev,
+ (gpio0->path.pnp.device >> 8) + NCT5104D_GPIO0_PP_OD, 0xFF);
if (gpio1 && gpio1->enabled)
- pnp_write_config(dev, NCT5104D_GPIO1_PP_OD, 0xFF);
+ pnp_write_config(dev,
+ (gpio1->path.pnp.device >> 8) + NCT5104D_GPIO0_PP_OD, 0xFF);
if (gpio6 && gpio6->enabled)
- pnp_write_config(dev, NCT5104D_GPIO6_PP_OD, 0xFF);
+ pnp_write_config(dev,
+ (gpio6->path.pnp.device >> 8) + NCT5104D_GPIO0_PP_OD, 0xFF);
}
static void disable_gpio_io_port(struct device *dev)
@@ -181,13 +185,14 @@
case NCT5104D_GPIO0:
case NCT5104D_GPIO1:
route_pins_to_uart(dev, false);
- reset_gpio_default_in(dev);
- break;
+ /* FALLTHROUGH */
case NCT5104D_GPIO6:
- reset_gpio_default_in(dev);
+ if (conf->reset_gpios)
+ reset_gpio_default_in(dev);
break;
case NCT5104D_GPIO_PP_OD:
- reset_gpio_default_od(dev);
+ if (conf->reset_gpios)
+ reset_gpio_default_od(dev);
break;
case NCT5104D_GPIO_IO:
disable_gpio_io_port(dev);