libgfxinit is a library of full-featured graphics initialization (aka. modesetting) drivers. It's implemented in SPARK (a subset of Ada with formal verification features). While not restricted to in any way, it currently only supports Intel's integrated gfx control- lers (GMA).
Currently, it supports the Intel Core i3/i5/i7 processor line and will support HDMI and DP on the Atom successor Apollo Lake. At the time of writing, Sandy Bridge, Ivy Bridge, and Haswell are veri- fied to work within coreboot.
coreboot supports two different framebuffer setups. The default enables the legacy VGA plane in textmode. Due to legacy hardware constraints, only the first found display is enabled in this mode. (cf.
The second option sets up a high-resolution framebuffer with the native resolution of the display if only one is detected, or the smallest of all resolutions (per dimension) if multiple displays are detected. This option is selected by
In any case, a smaller framebuffer is up-scaled to each display's native resolution while keeping aspect ratio.
Both configurations described above implement a procedure
procedure gfxinit (lightup_ok : out int);
This procedure is exported as the C function
gma_gfxinit() as follows:
void gma_gfxinit(int *lightup_ok);
lightup_ok: returns whether the initialization succeeded
0. Currently, only the case that no display could be found counts as failure. A failure at a la- ter stage (e.g. failure to train a DP) is not propa- gated.
There are a few Kconfig symbols to consider. To indicate that a board can initialize graphics through libgfxinit:
Internal ports share some hardware blocks (e.g. backlight, panel power sequencer). Therefore, each board has to select either eDP or LVDS as the internal port, if any:
select GFX_GMA_INTERNAL_IS_EDP # the default, or select GFX_GMA_INTERNAL_IS_LVDS
Boards with a DVI-I connector share the DDC (I2C) pins for both analog and digital displays. In this case, libgfxinit needs to know through which interface the EDID can be queried:
select GFX_GMA_ANALOG_I2C_HDMI_B # or select GFX_GMA_ANALOG_I2C_HDMI_C # or select GFX_GMA_ANALOG_I2C_HDMI_D
Beside Kconfig options, libgfxinit needs to know which ports are implemented on a board and should be probed for displays. Each board has to implement the package
GMA.Mainboard with a list:
ports : HW.GFX.GMA.Display_Probing.Port_List;
or a function returning such a list:
function ports return HW.GFX.GMA.Display_Probing.Port_List;
You can select from the following Ports:
type Port_Type is (Disabled, -- optionally terminates the list Internal, -- either eDP or LVDS as selected in Kconfig DP1, DP2, DP3, HDMI1, -- also DVI-D, or HDMI over DP++ HDMI2, HDMI3, Analog); -- legacy VGA port, or analog part of DVI-I
HDMIx pair share pins. If they are exposed as DP ports, they are usually DP++ (aka. dual-mode DP) ports that can also output HDMI signals through passive adapters. In this case, both DPx and HDMIx should be listed.
A good example is the mainboard Kontron/KTQM77, it features two DP++ ports (DP2/HDMI2, DP3/HDMI3), one DVI-I port (HDMI1/Analog), eDP and LVDS. Due to the constraints mentioned above, only one of eDP and LVDS can be enabled. It defines
ports as follows:
ports : constant Port_List := (DP2, DP3, HDMI1, HDMI2, HDMI3, Analog, Internal, others => Disabled);
GMA.gfxinit() procedure probes for display EDIDs in the given order until all available pipes are taken. That's 1 pipe in VGA textmode, 2 pipes in high-resolution mode until Sandy Bridge, 3 pipes from Ivy Bridge on.