Gitiles
Code Review Sign In
review.coreboot.org / coreboot / 3e3c4560e190169bfe1f2ae53ff5ba33613486c3 / . / src / vendorcode / intel / fsp / fsp2_0 / tigerlake / FspmUpd.h
blob: 6210f3c5cbd3c6738e6adda7cbea78e29f3d4b24 [file] [log] [blame]
/** @file
Copyright (c) 2021, Intel Corporation. All rights reserved.<BR>
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This file is automatically generated. Please do NOT modify !!!
**/
#ifndef __FSPMUPD_H__
#define __FSPMUPD_H__
#include <FspUpd.h>
#pragma pack(1)
#include <MemInfoHob.h>
///
/// The ChipsetInit Info structure provides the information of ME ChipsetInit CRC and BIOS ChipsetInit CRC.
///
typedef struct {
UINT8 Revision; ///< Chipset Init Info Revision
UINT8 Rsvd[3]; ///< Reserved
UINT16 MeChipInitCrc; ///< 16 bit CRC value of MeChipInit Table
UINT16 BiosChipInitCrc; ///< 16 bit CRC value of PchChipInit Table
} CHIPSET_INIT_INFO;
/** Fsp M Configuration
**/
typedef struct {
/** Offset 0x0040 - Platform Reserved Memory Size
The minimum platform memory size required to pass control into DXE
**/
UINT64 PlatformMemorySize;
/** Offset 0x0048 - SPD Data Length
Length of SPD Data
0x100:256 Bytes, 0x200:512 Bytes, 0x400:1024 Bytes
**/
UINT16 MemorySpdDataLen;
/** Offset 0x004A - Enable above 4GB MMIO resource support
Enable/disable above 4GB MMIO resource support
$EN_DIS
**/
UINT8 EnableAbove4GBMmio;
/** Offset 0x004B - Enable/Disable CrashLog Device 10
Enable(Default): Enable CPU CrashLog Device 10, Disable: Disable CPU CrashLog
$EN_DIS
**/
UINT8 CpuCrashLogDevice;
/** Offset 0x004C - MemorySpdPtr00
**/
UINT32 MemorySpdPtr00;
/** Offset 0x0050 - MemorySpdPtr01
**/
UINT32 MemorySpdPtr01;
/** Offset 0x0054 - MemorySpdPtr02
**/
UINT32 MemorySpdPtr02;
/** Offset 0x0058 - MemorySpdPtr03
**/
UINT32 MemorySpdPtr03;
/** Offset 0x005C - MemorySpdPtr04
**/
UINT32 MemorySpdPtr04;
/** Offset 0x0060 - MemorySpdPtr05
**/
UINT32 MemorySpdPtr05;
/** Offset 0x0064 - MemorySpdPtr06
**/
UINT32 MemorySpdPtr06;
/** Offset 0x0068 - MemorySpdPtr07
**/
UINT32 MemorySpdPtr07;
/** Offset 0x006C - MemorySpdPtr08
**/
UINT32 MemorySpdPtr08;
/** Offset 0x0070 - MemorySpdPtr09
**/
UINT32 MemorySpdPtr09;
/** Offset 0x0074 - MemorySpdPtr10
**/
UINT32 MemorySpdPtr10;
/** Offset 0x0078 - MemorySpdPtr11
**/
UINT32 MemorySpdPtr11;
/** Offset 0x007C - MemorySpdPtr12
**/
UINT32 MemorySpdPtr12;
/** Offset 0x0080 - MemorySpdPtr13
**/
UINT32 MemorySpdPtr13;
/** Offset 0x0084 - MemorySpdPtr14
**/
UINT32 MemorySpdPtr14;
/** Offset 0x0088 - MemorySpdPtr15
**/
UINT32 MemorySpdPtr15;
/** Offset 0x008C - RcompResistor settings
Indicates RcompResistor settings: Board-dependent
**/
UINT16 RcompResistor;
/** Offset 0x008E - RcompTarget settings
RcompTarget settings: board-dependent
**/
UINT16 RcompTarget[5];
/** Offset 0x0098 - DqsMapCpu2DramCh0
**/
UINT8 DqsMapCpu2DramCh0[2];
/** Offset 0x009A - DqsMapCpu2DramCh1
**/
UINT8 DqsMapCpu2DramCh1[2];
/** Offset 0x009C - DqsMapCpu2DramCh2
**/
UINT8 DqsMapCpu2DramCh2[2];
/** Offset 0x009E - DqsMapCpu2DramCh3
**/
UINT8 DqsMapCpu2DramCh3[2];
/** Offset 0x00A0 - DqsMapCpu2DramCh4
**/
UINT8 DqsMapCpu2DramCh4[2];
/** Offset 0x00A2 - DqsMapCpu2DramCh5
**/
UINT8 DqsMapCpu2DramCh5[2];
/** Offset 0x00A4 - DqsMapCpu2DramCh6
**/
UINT8 DqsMapCpu2DramCh6[2];
/** Offset 0x00A6 - DqsMapCpu2DramCh7
**/
UINT8 DqsMapCpu2DramCh7[2];
/** Offset 0x00A8 - DqMapCpu2DramCh0
**/
UINT8 DqMapCpu2DramCh0[16];
/** Offset 0x00B8 - DqMapCpu2DramCh1
**/
UINT8 DqMapCpu2DramCh1[16];
/** Offset 0x00C8 - DqMapCpu2DramCh2
**/
UINT8 DqMapCpu2DramCh2[16];
/** Offset 0x00D8 - DqMapCpu2DramCh3
**/
UINT8 DqMapCpu2DramCh3[16];
/** Offset 0x00E8 - DqMapCpu2DramCh4
**/
UINT8 DqMapCpu2DramCh4[16];
/** Offset 0x00F8 - DqMapCpu2DramCh5
**/
UINT8 DqMapCpu2DramCh5[16];
/** Offset 0x0108 - DqMapCpu2DramCh6
**/
UINT8 DqMapCpu2DramCh6[16];
/** Offset 0x0118 - DqMapCpu2DramCh7
**/
UINT8 DqMapCpu2DramCh7[16];
/** Offset 0x0128 - Dqs Pins Interleaved Setting
Indicates DqPinsInterleaved setting: board-dependent
$EN_DIS
**/
UINT8 DqPinsInterleaved;
/** Offset 0x0129 - Smram Mask
The SMM Regions AB-SEG and/or H-SEG reserved
0: Neither, 1:AB-SEG, 2:H-SEG, 3: Both
**/
UINT8 SmramMask;
/** Offset 0x012A - MRC Fast Boot
Enables/Disable the MRC fast path thru the MRC
$EN_DIS
**/
UINT8 MrcFastBoot;
/** Offset 0x012B - Rank Margin Tool per Task
This option enables the user to execute Rank Margin Tool per major training step
in the MRC.
$EN_DIS
**/
UINT8 RmtPerTask;
/** Offset 0x012C - Training Trace
This option enables the trained state tracing feature in MRC. This feature will
print out the key training parameters state across major training steps.
$EN_DIS
**/
UINT8 TrainTrace;
/** Offset 0x012D
**/
UINT8 UnusedUpdSpace0[3];
/** Offset 0x0130 - Intel Enhanced Debug
<b>@deprecated</b> - Not used and has no effect
0 : Disable, 0x400000 : Enable
**/
UINT32 IedSize;
/** Offset 0x0134 - Tseg Size
Size of SMRAM memory reserved. 0x400000 for Release build and 0x1000000 for Debug build
0x0400000:4MB, 0x01000000:16MB
**/
UINT32 TsegSize;
/** Offset 0x0138 - MMIO Size
Size of MMIO space reserved for devices. 0(Default)=Auto, non-Zero=size in MB
**/
UINT16 MmioSize;
/** Offset 0x013A - Probeless Trace
Probeless Trace: 0=Disabled, 1=Enable. Enabling Probeless Trace will reserve 128MB.
This also requires IED to be enabled.
$EN_DIS
**/
UINT8 ProbelessTrace;
/** Offset 0x013B - Enable SMBus
Enable/disable SMBus controller.
$EN_DIS
**/
UINT8 SmbusEnable;
/** Offset 0x013C - Spd Address Tabl
Specify SPD Address table for CH0D0/CH0D1/CH1D0&CH1D1. MemorySpdPtr will be used
if SPD Address is 00
**/
UINT8 SpdAddressTable[16];
/** Offset 0x014C - Platform Debug Consent
To 'opt-in' for debug, please select 'Enabled' with the desired debug probe type.
Enabling this BIOS option may alter the default value of other debug-related BIOS
options.\Manual: Do not use Platform Debug Consent to override other debug-relevant
policies, but the user must set each debug option manually, aimed at advanced users.\n
Note: DCI OOB (aka BSSB) uses CCA probe;[DCI OOB+DbC] and [USB2 DbC] have the same setting.
0:Disabled, 1:Enabled (DCI OOB+[DbC]), 2:Enabled (DCI OOB), 3:Enabled (USB3 DbC),
4:Enabled (XDP/MIPI60), 5:Enabled (USB2 DbC), 6:Enable (2-wire DCI OOB), 7:Manual
**/
UINT8 PlatformDebugConsent;
/** Offset 0x014D - DCI Enable
Determine if to enable DCI debug from host
$EN_DIS
**/
UINT8 DciEn;
/** Offset 0x014E - DCI DbC Mode
Disabled: Clear both USB2/3DBCEN; USB2: set USB2DBCEN; USB3: set USB3DBCEN; Both:
Set both USB2/3DBCEN; No Change: Comply with HW value
0:Disabled, 1:USB2 DbC, 2:USB3 DbC, 3:Both, 4:No Change
**/
UINT8 DciDbcMode;
/** Offset 0x014F - Enable DCI ModPHY Power Gate
Enable ModPHY Power Gate when DCI is enabled
$EN_DIS
**/
UINT8 DciModphyPg;
/** Offset 0x0150 - USB3 Type-C UFP2DFP Kernel/Platform Debug Support
This BIOS option enables kernel and platform debug for USB3 interface over a UFP
Type-C receptacle, select 'No Change' will do nothing to UFP2DFP setting.
0:Disabled, 1:Enabled, 2:No Change
**/
UINT8 DciUsb3TypecUfpDbg;
/** Offset 0x0151 - PCH Trace Hub Mode
Select 'Host Debugger' if Trace Hub is used with host debugger tool or 'Target Debugger'
if Trace Hub is used by target debugger software or 'Disable' trace hub functionality.
0: Disable, 1: Target Debugger Mode, 2: Host Debugger Mode
**/
UINT8 PchTraceHubMode;
/** Offset 0x0152 - PCH Trace Hub Memory Region 0 buffer Size
Specify size of Pch trace memory region 0 buffer, the size can be 0, 1MB, 8MB, 64MB,
128MB, 256MB, 512MB. Note : Limitation of total buffer size (PCH + CPU) is 512MB.
0:0, 1:1MB, 2:8MB, 3:64MB, 4:128MB, 5:256MB, 6:512MB
**/
UINT8 PchTraceHubMemReg0Size;
/** Offset 0x0153 - PCH Trace Hub Memory Region 1 buffer Size
Specify size of Pch trace memory region 1 buffer, the size can be 0, 1MB, 8MB, 64MB,
128MB, 256MB, 512MB. Note : Limitation of total buffer size (PCH + CPU) is 512MB.
0:0, 1:1MB, 2:8MB, 3:64MB, 4:128MB, 5:256MB, 6:512MB
**/
UINT8 PchTraceHubMemReg1Size;
/** Offset 0x0154 - HD Audio DMIC Link Clock Select
Determines DMIC<N> Clock Source. 0: Both, 1: ClkA, 2: ClkB
0: Both, 1: ClkA, 2: ClkB
**/
UINT8 PchHdaAudioLinkDmicClockSelect[2];
/** Offset 0x0156 - PchPreMemRsvd
Reserved for PCH Pre-Mem Reserved
$EN_DIS
**/
UINT8 PchPreMemRsvd[5];
/** Offset 0x015B - State of X2APIC_OPT_OUT bit in the DMAR table
0=Disable/Clear, 1=Enable/Set
$EN_DIS
**/
UINT8 X2ApicOptOut;
/** Offset 0x015C - State of DMA_CONTROL_GUARANTEE bit in the DMAR table
0=Disable/Clear, 1=Enable/Set
$EN_DIS
**/
UINT8 DmaControlGuarantee;
/** Offset 0x015D
**/
UINT8 UnusedUpdSpace1[3];
/** Offset 0x0160 - Base addresses for VT-d function MMIO access
Base addresses for VT-d MMIO access per VT-d engine
**/
UINT32 VtdBaseAddress[9];
/** Offset 0x0184 - Disable VT-d
0=Enable/FALSE(VT-d enabled), 1=Disable/TRUE (VT-d disabled)
$EN_DIS
**/
UINT8 VtdDisable;
/** Offset 0x0185 - Vtd Programming for Igd
1=Enable/TRUE (Igd VT-d Bar programming enabled), 0=Disable/FLASE (Igd VT-d Bar
programming disabled)
$EN_DIS
**/
UINT8 VtdIgdEnable;
/** Offset 0x0186 - Vtd Programming for Ipu
1=Enable/TRUE (Ipu VT-d Bar programming enabled), 0=Disable/FLASE (Ipu VT-d Bar
programming disabled)
$EN_DIS
**/
UINT8 VtdIpuEnable;
/** Offset 0x0187 - Vtd Programming for Iop
1=Enable/TRUE (Iop VT-d Bar programming enabled), 0=Disable/FLASE (Iop VT-d Bar
programming disabled)
$EN_DIS
**/
UINT8 VtdIopEnable;
/** Offset 0x0188 - Vtd Programming for ITbt
1=Enable/TRUE (ITbt VT-d Bar programming enabled), 0=Disable/FLASE (ITbt VT-d Bar
programming disabled)
$EN_DIS
**/
UINT8 VtdItbtEnable;
/** Offset 0x0189 - Internal Graphics Pre-allocated Memory
Size of memory preallocated for internal graphics.
0x00:0MB, 0x01:32MB, 0x02:64MB, 0x03:96MB, 0x04:128MB, 0x05:160MB, 0xF0:4MB, 0xF1:8MB,
0xF2:12MB, 0xF3:16MB, 0xF4:20MB, 0xF5:24MB, 0xF6:28MB, 0xF7:32MB, 0xF8:36MB, 0xF9:40MB,
0xFA:44MB, 0xFB:48MB, 0xFC:52MB, 0xFD:56MB, 0xFE:60MB
**/
UINT8 IgdDvmt50PreAlloc;
/** Offset 0x018A - Internal Graphics
Enable/disable internal graphics.
$EN_DIS
**/
UINT8 InternalGfx;
/** Offset 0x018B - Aperture Size
Select the Aperture Size.
0:128 MB, 1:256 MB, 3:512 MB, 7:1024 MB, 15: 2048 MB
**/
UINT8 ApertureSize;
/** Offset 0x018C - Board Type
MrcBoardType, Options are 0=Mobile/Mobile Halo, 1=Desktop/DT Halo, 5=ULT/ULX/Mobile
Halo, 7=UP Server
0:Mobile/Mobile Halo, 1:Desktop/DT Halo, 5:ULT/ULX/Mobile Halo, 7:UP Server
**/
UINT8 UserBd;
/** Offset 0x018D
**/
UINT8 UnusedUpdSpace2;
/** Offset 0x018E - DDR Frequency Limit
Maximum Memory Frequency Selections in Mhz. Options are 1067, 1333, 1600, 1867,
2133, 2400, 2667, 2933 and 0 for Auto.
1067:1067, 1333:1333, 1600:1600, 1867:1867, 2133:2133, 2400:2400, 2667:2667, 2933:2933, 0:Auto
**/
UINT16 DdrFreqLimit;
/** Offset 0x0190 - SA GV
System Agent dynamic frequency support and when enabled memory will be training
at three different frequencies.
0:Disabled, 1:FixedPoint0, 2:FixedPoint1, 3:FixedPoint2, 4:FixedPoint3, 5:Enabled
**/
UINT8 SaGv;
/** Offset 0x0191 - Memory Test on Warm Boot
Run Base Memory Test on Warm Boot
0:Disable, 1:Enable
**/
UINT8 MemTestOnWarmBoot;
/** Offset 0x0192 - DDR Speed Control
DDR Frequency and Gear control for all SAGV points.
0:Auto, 1:Manual
**/
UINT8 DdrSpeedControl;
/** Offset 0x0193 - Rank Margin Tool
Enable/disable Rank Margin Tool.
$EN_DIS
**/
UINT8 RMT;
/** Offset 0x0194 - DisableDimmCh0
**/
UINT8 DisableDimmCh0;
/** Offset 0x0195 - DisableDimmCh1
**/
UINT8 DisableDimmCh1;
/** Offset 0x0196 - DisableDimmCh2
**/
UINT8 DisableDimmCh2;
/** Offset 0x0197 - DisableDimmCh3
**/
UINT8 DisableDimmCh3;
/** Offset 0x0198 - DisableDimmCh4
**/
UINT8 DisableDimmCh4;
/** Offset 0x0199 - DisableDimmCh5
**/
UINT8 DisableDimmCh5;
/** Offset 0x019A - DisableDimmCh6
**/
UINT8 DisableDimmCh6;
/** Offset 0x019B - DisableDimmCh7
**/
UINT8 DisableDimmCh7;
/** Offset 0x019C - Scrambler Support
This option enables data scrambling in memory.
$EN_DIS
**/
UINT8 ScramblerSupport;
/** Offset 0x019D - SPD Profile Selected
Select DIMM timing profile. Options are 0=Default Profile, 1=Custom Profile, 2=XMP
Profile 1, 3=XMP Profile 2
0:Default Profile, 1:Custom Profile, 2:XMP Profile 1, 3:XMP Profile 2
**/
UINT8 SpdProfileSelected;
/** Offset 0x019E - Memory Reference Clock
100MHz, 133MHz.
0:133MHz, 1:100MHz
**/
UINT8 RefClk;
/** Offset 0x019F
**/
UINT8 UnusedUpdSpace3;
/** Offset 0x01A0 - Memory Voltage
DRAM voltage (Vdd) (supply voltage for input buffers and core logic of the DRAM
chips) in millivolts. <b>0=Platform Default (no override)</b>, 1200=1.2V, 1350=1.35V etc.
0:Default, 1200:1.20 Volts, 1250:1.25 Volts, 1300:1.30 Volts, 1350:1.35 Volts, 1400:1.40
Volts, 1450:1.45 Volts, 1500:1.50 Volts, 1550:1.55 Volts, 1600:1.60 Volts, 1650:1.65 Volts
**/
UINT16 VddVoltage;
/** Offset 0x01A2 - Memory Ratio
Automatic or the frequency will equal ratio times reference clock. Set to Auto to
recalculate memory timings listed below.
0:Auto, 4:4, 5:5, 6:6, 7:7, 8:8, 9:9, 10:10, 11:11, 12:12, 13:13, 14:14, 15:15
**/
UINT8 Ratio;
/** Offset 0x01A3 - tCL
CAS Latency, 0: AUTO, max: 31. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT8 tCL;
/** Offset 0x01A4 - tCWL
Min CAS Write Latency Delay Time, 0: AUTO, max: 34. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT8 tCWL;
/** Offset 0x01A5
**/
UINT8 UnusedUpdSpace4;
/** Offset 0x01A6 - tFAW
Min Four Activate Window Delay Time, 0: AUTO, max: 63. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT16 tFAW;
/** Offset 0x01A8 - tRAS
RAS Active Time, 0: AUTO, max: 64. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT16 tRAS;
/** Offset 0x01AA - tRCD/tRP
RAS to CAS delay time and Row Precharge delay time, 0: AUTO, max: 63. Only used
if FspmUpd->FspmConfig.SpdProfileSelected == 1 (Custom Profile).
**/
UINT8 tRCDtRP;
/** Offset 0x01AB
**/
UINT8 UnusedUpdSpace5;
/** Offset 0x01AC - tREFI
Refresh Interval, 0: AUTO, max: 65535. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT16 tREFI;
/** Offset 0x01AE - tRFC
Min Refresh Recovery Delay Time, 0: AUTO, max: 1023. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT16 tRFC;
/** Offset 0x01B0 - tRRD
Min Row Active to Row Active Delay Time, 0: AUTO, max: 15. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT8 tRRD;
/** Offset 0x01B1 - tRTP
Min Internal Read to Precharge Command Delay Time, 0: AUTO, max: 15. DDR4 legal
values: 5, 6, 7, 8, 9, 10, 12. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT8 tRTP;
/** Offset 0x01B2 - tWR
Min Write Recovery Time, 0: AUTO, legal values: 5, 6, 7, 8, 10, 12, 14, 16, 18,
20, 24, 30, 34, 40. Only used if FspmUpd->FspmConfig.SpdProfileSelected == 1 (Custom Profile).
0:Auto, 5:5, 6:6, 7:7, 8:8, 10:10, 12:12, 14:14, 16:16, 18:18, 20:20, 24:24, 30:30,
34:34, 40:40
**/
UINT8 tWR;
/** Offset 0x01B3 - tWTR
Min Internal Write to Read Command Delay Time, 0: AUTO, max: 28. Only used if FspmUpd->FspmConfig.SpdProfileSelected
== 1 (Custom Profile).
**/
UINT8 tWTR;
/** Offset 0x01B4 - NMode
System command rate, range 0-2, 0 means auto, 1 = 1N, 2 = 2N
**/
UINT8 NModeSupport;
/** Offset 0x01B5 - Enable Intel HD Audio (Azalia)
0: Disable, 1: Enable (Default) Azalia controller
$EN_DIS
**/
UINT8 PchHdaEnable;
/** Offset 0x01B6 - Enable PCH ISH Controller
0: Disable, 1: Enable (Default) ISH Controller
$EN_DIS
**/
UINT8 PchIshEnable;
/** Offset 0x01B7 - CPU Trace Hub Mode
Select 'Host Debugger' if Trace Hub is used with host debugger tool or 'Target Debugger'
if Trace Hub is used by target debugger software or 'Disable' trace hub functionality.
0: Disable, 1:Target Debugger Mode, 2:Host Debugger Mode
**/
UINT8 CpuTraceHubMode;
/** Offset 0x01B8 - CPU Trace Hub Memory Region 0
CPU Trace Hub Memory Region 0, The avaliable memory size is : 0MB, 1MB, 8MB, 64MB,
128MB, 256MB, 512MB. Note : Limitation of total buffer size (CPU + PCH) is 512MB.
0:0, 1:1MB, 2:8MB, 3:64MB, 4:128MB, 5:256MB, 6:512MB
**/
UINT8 CpuTraceHubMemReg0Size;
/** Offset 0x01B9 - CPU Trace Hub Memory Region 1
CPU Trace Hub Memory Region 1. The avaliable memory size is : 0MB, 1MB, 8MB, 64MB,
128MB, 256MB, 512MB. Note : Limitation of total buffer size (CPU + PCH) is 512MB.
0:0, 1:1MB, 2:8MB, 3:64MB, 4:128MB, 5:256MB, 6:512MB
**/
UINT8 CpuTraceHubMemReg1Size;
/** Offset 0x01BA - SAGV Gear Ratio
Gear Selection for SAGV points. 0 - Auto, 1-1 Gear 1, 2-Gear 2
**/
UINT8 SaGvGear[4];
/** Offset 0x01BE - SAGV Frequency
SAGV Frequency per point in Mhz. 0 for Auto and a ratio of 133/100MHz: 1333/1300.
**/
UINT16 SaGvFreq[4];
/** Offset 0x01C6 - SAGV Disabled Gear Ratio
Gear Selection for SAGV Disabled. 0 - Auto, 1-1 Gear 1, 2-Gear 2
**/
UINT8 GearRatio;
/** Offset 0x01C7 - HECI Timeouts
0: Disable, 1: Enable (Default) timeout check for HECI
$EN_DIS
**/
UINT8 HeciTimeouts;
/** Offset 0x01C8 - HECI1 BAR address
BAR address of HECI1
**/
UINT32 Heci1BarAddress;
/** Offset 0x01CC - HECI2 BAR address
BAR address of HECI2
**/
UINT32 Heci2BarAddress;
/** Offset 0x01D0 - HECI3 BAR address
BAR address of HECI3
**/
UINT32 Heci3BarAddress;
/** Offset 0x01D4 - HG dGPU Power Delay
HG dGPU delay interval after power enabling: 0=Minimal, 1000=Maximum, default is
300=300 microseconds
**/
UINT16 HgDelayAfterPwrEn;
/** Offset 0x01D6 - HG dGPU Reset Delay
HG dGPU delay interval for Reset complete: 0=Minimal, 1000=Maximum, default is 100=100
microseconds
**/
UINT16 HgDelayAfterHoldReset;
/** Offset 0x01D8 - MMIO size adjustment for AUTO mode
Positive number means increasing MMIO size, Negative value means decreasing MMIO
size: 0 (Default)=no change to AUTO mode MMIO size
**/
UINT16 MmioSizeAdjustment;
/** Offset 0x01DA - PCIe ASPM programming will happen in relation to the Oprom
Select when PCIe ASPM programming will happen in relation to the Oprom. Before(0x0)(Default):
Do PCIe ASPM programming before Oprom, After(0x1): Do PCIe ASPM programming after
Oprom, requires an SMI handler to save/restore ASPM settings during S3 resume
0:Before, 1:After
**/
UINT8 InitPcieAspmAfterOprom;
/** Offset 0x01DB - Selection of the primary display device
0=iGFX, 1=PEG, 2=PCIe Graphics on PCH, 3(Default)=AUTO, 4=Hybrid Graphics
0:iGFX, 1:PEG, 2:PCIe Graphics on PCH, 3:AUTO, 4:Hybrid Graphics
**/
UINT8 PrimaryDisplay;
/** Offset 0x01DC - Selection of PSMI Region size
0=32MB, 1=288MB, 2=544MB, 3=800MB, 4=1024MB Default is 0
0:32MB, 1:288MB, 2:544MB, 3:800MB, 4:1024MB
**/
UINT8 PsmiRegionSize;
/** Offset 0x01DD
**/
UINT8 UnusedUpdSpace6[3];
/** Offset 0x01E0 - Temporary MMIO address for GMADR
Obsolete field now and it has been extended to 64 bit address, used GmAdr64
**/
UINT32 GmAdr;
/** Offset 0x01E4 - Temporary MMIO address for GTTMMADR
The reference code will use this as Temporary MMIO address space to access GTTMMADR
Registers.Platform should provide conflict free Temporary MMIO Range: GttMmAdr
to (GttMmAdr + 2MB MMIO + 6MB Reserved + GttSize). Default is (GmAdr - (2MB MMIO
+ 6MB Reserved + GttSize)) to (GmAdr - 0x1) (Where GttSize = 8MB)
**/
UINT32 GttMmAdr;
/** Offset 0x01E8 - Selection of iGFX GTT Memory size
1=2MB, 2=4MB, 3=8MB, Default is 3
1:2MB, 2:4MB, 3:8MB
**/
UINT16 GttSize;
/** Offset 0x01EA
**/
UINT8 UnusedUpdSpace7[2];
/** Offset 0x01EC - Hybrid Graphics GPIO information for PEG 0
Hybrid Graphics GPIO information for PEG 0, for Reset, power and wake GPIOs
**/
UINT32 CpuPcie0Rtd3Gpio[24];
/** Offset 0x024C - Enable/Disable MRC TXT dependency
When enabled MRC execution will wait for TXT initialization to be done first. Disabled(0x0)(Default):
MRC will not wait for TXT initialization, Enabled(0x1): MRC will wait for TXT initialization
$EN_DIS
**/
UINT8 TxtImplemented;
/** Offset 0x024D - Enable/Disable SA OcSupport
Enable: Enable SA OcSupport, Disable(Default): Disable SA OcSupport
$EN_DIS
**/
UINT8 SaOcSupport;
/** Offset 0x024E - GT slice Voltage Mode
0(Default): Adaptive, 1: Override
0: Adaptive, 1: Override
**/
UINT8 GtVoltageMode;
/** Offset 0x024F - Maximum GTs turbo ratio override
0(Default)=Minimal/Auto, 60=Maximum
**/
UINT8 GtMaxOcRatio;
/** Offset 0x0250 - The voltage offset applied to GT slice
0(Default)=Minimal, 1000=Maximum
**/
UINT16 GtVoltageOffset;
/** Offset 0x0252 - The GT slice voltage override which is applied to the entire range of GT frequencies
0(Default)=Minimal, 2000=Maximum
**/
UINT16 GtVoltageOverride;
/** Offset 0x0254 - adaptive voltage applied during turbo frequencies
0(Default)=Minimal, 2000=Maximum
**/
UINT16 GtExtraTurboVoltage;
/** Offset 0x0256 - voltage offset applied to the SA
0(Default)=Minimal, 1000=Maximum
**/
UINT16 SaVoltageOffset;
/** Offset 0x0258 - PCIe root port Function number for Hybrid Graphics dGPU
Root port Index number to indicate which PCIe root port has dGPU
**/
UINT8 RootPortIndex;
/** Offset 0x0259 - Realtime Memory Timing
0(Default): Disabled, 1: Enabled. When enabled, it will allow the system to perform
realtime memory timing changes after MRC_DONE.
0: Disabled, 1: Enabled
**/
UINT8 RealtimeMemoryTiming;
/** Offset 0x025A - iTBT PCIe Multiple Segment setting
When Disabled all the TBT PCIe RP are located at Segment0, When Enabled all the
TBT PCIe RP are located at Segment1. <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 PcieMultipleSegmentEnabled;
/** Offset 0x025B - Enable/Disable SA IPU
Enable(Default): Enable SA IPU, Disable: Disable SA IPU
$EN_DIS
**/
UINT8 SaIpuEnable;
/** Offset 0x025C - IPU IMR Configuration
0:IPU Camera, 1:IPU Gen Default is 0
0:IPU Camera, 1:IPU Gen
**/
UINT8 SaIpuImrConfiguration;
/** Offset 0x025D - IMGU CLKOUT Configuration
The configuration of IMGU CLKOUT, 0: Disable;<b>1: Enable</b>.
$EN_DIS
**/
UINT8 ImguClkOutEn[6];
/** Offset 0x0263
**/
UINT8 UnusedUpdSpace8;
/** Offset 0x0264 - Enable PCIE RP Mask
Enable/disable PCIE Root Ports. 0: disable, 1: enable. One bit for each port, bit0
for port1, bit1 for port2, and so on.
**/
UINT32 CpuPcieRpEnableMask;
/** Offset 0x0268 - Assertion on Link Down GPIOs
GPIO Assertion on Link Down. Disabled(0x0)(Default): Disable assertion on Link Down
GPIOs, Enabled(0x1): Enable assertion on Link Down GPIOs
0:Disable, 1:Enable
**/
UINT8 CpuPcieRpLinkDownGpios;
/** Offset 0x0269 - RpClockReqMsgEnable
**/
UINT8 RpClockReqMsgEnable;
/** Offset 0x026A - RpPcieThresholdBytes
**/
UINT8 RpPcieThresholdBytes[4];
/** Offset 0x026E - Selection of PSMI Support On/Off
0(Default) = FALSE, 1 = TRUE. When TRUE, it will allow the PSMI Support
$EN_DIS
**/
UINT8 GtPsmiSupport;
/** Offset 0x026F - Selection of DiSM Region Size
DiSM Size to be allocated for 2LM Sku Default is 0
0:0GB, 1:1GB, 2:2GB, 3:3GB, 4:4GB, 5:5GB, 6:6GB, 7:7GB
**/
UINT8 DismSize;
/** Offset 0x0270 - Enable Display memory map programming for DFD Restore
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DfdRestoreEnable;
/** Offset 0x0271 - Program GPIOs for LFP on DDI port-A device
0=Disabled,1(Default)=eDP, 2=MIPI DSI
0:Disabled, 1:eDP, 2:MIPI DSI
**/
UINT8 DdiPortAConfig;
/** Offset 0x0272 - Program GPIOs for LFP on DDI port-B device
0(Default)=Disabled,1=eDP, 2=MIPI DSI
0:Disabled, 1:eDP, 2:MIPI DSI
**/
UINT8 DdiPortBConfig;
/** Offset 0x0273 - Enable or disable HPD of DDI port A
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPortAHpd;
/** Offset 0x0274 - Enable or disable HPD of DDI port B
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortBHpd;
/** Offset 0x0275 - Enable or disable HPD of DDI port C
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPortCHpd;
/** Offset 0x0276 - Enable or disable HPD of DDI port 1
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPort1Hpd;
/** Offset 0x0277 - Enable or disable HPD of DDI port 2
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPort2Hpd;
/** Offset 0x0278 - Enable or disable HPD of DDI port 3
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPort3Hpd;
/** Offset 0x0279 - Enable or disable HPD of DDI port 4
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPort4Hpd;
/** Offset 0x027A - Enable or disable DDC of DDI port A
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPortADdc;
/** Offset 0x027B - Enable or disable DDC of DDI port B
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 DdiPortBDdc;
/** Offset 0x027C - Enable or disable DDC of DDI port C
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPortCDdc;
/** Offset 0x027D - Enable DDC setting of DDI Port 1
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPort1Ddc;
/** Offset 0x027E - Enable DDC setting of DDI Port 2
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPort2Ddc;
/** Offset 0x027F - Enable DDC setting of DDI Port 3
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPort3Ddc;
/** Offset 0x0280 - Enable DDC setting of DDI Port 4
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 DdiPort4Ddc;
/** Offset 0x0281 - Enable Gt CLOS
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 GtClosEnable;
/** Offset 0x0282
**/
UINT8 UnusedUpdSpace9[6];
/** Offset 0x0288 - Temporary MMIO address for GMADR
The reference code will use this as Temporary MMIO address space to access GMADR
Registers.Platform should provide conflict free Temporary MMIO Range: GmAdr to
(GmAdr + ApertureSize). Default is (PciExpressBaseAddress - ApertureSize) to (PciExpressBaseAddress
- 0x1) (Where ApertureSize = 256MB, 512MB, 1024MB and 2048MB)
**/
UINT64 GmAdr64;
/** Offset 0x0290 - Hybrid Graphics Slot Selection
PEG or PCH Slot Selection for Hybrid Graphics
**/
UINT8 HgSlot;
/** Offset 0x0291 - DMI ASPM Configuration:{Combo
Set ASPM Configuration
0:Disabled, 1:L0s, 2:L1, 3:L1L0s
**/
UINT8 DmiAspm;
/** Offset 0x0292 - DMI ASPM Control Configuration:{Combo
Set ASPM Control configuration
0:Disabled, 1:L0s, 2:L1, 3:L1L0s
**/
UINT8 DmiAspmCtrl;
/** Offset 0x0293 - DMI ASPM L1 exit Latency
Range: 0-7, 4 is default L1 exit Latency
**/
UINT8 DmiAspmL1ExitLatency;
/** Offset 0x0294 - Per-core HT Disable
Defines the per-core HT disable mask where: 1 - Disable selected logical core HT,
0 - is ignored. Input is in HEX and each bit maps to a logical core. Ex. A value
of '1F' would disable HT for cores 4,3,2,1 and 0. Default is 0, all cores have
HT enabled. Range is 0 - 0x7F for max 8 cores. You can only disable up to MAX_CORE_COUNT - 1.
**/
UINT16 PerCoreHtDisable;
/** Offset 0x0296 - DEKEL CDR Relock
Enable/Disable CDR Relock. 0: Disable(Default); 1: Enable
**/
UINT8 CpuPcieRpCdrRelock[4];
/** Offset 0x029A - Realtime Memory OverClock
Disable/Enables Realtime Memory OverClock
$EN_DIS
**/
UINT8 RealtimeMemoryOC;
/** Offset 0x029B - Xl1el
Enable/Disable NewFom for DEKEL Programming. 0: Disable(Default); 1: Enable
**/
UINT8 CpuPcieNewFom[4];
/** Offset 0x029F - Xl1el
Enable/Disable NewFomDisable. 0: Disable(Default); 1: Enable
**/
UINT8 CpuPcieIotgMode[4];
/** Offset 0x02A3 - SaPreMemProductionRsvd
Reserved for SA Pre-Mem Production
$EN_DIS
**/
UINT8 SaPreMemProductionRsvd[87];
/** Offset 0x02FA - DMI Max Link Speed
Auto (0x0): Maximum possible link speed, Gen1(0x1): Limit Link to Gen1 Speed, Gen2(0x2):
Limit Link to Gen2 Speed, (Default) Gen3(0x3):Limit Link to Gen3 Speed
0:Auto, 1:Gen1, 2:Gen2, 3:Gen3
**/
UINT8 DmiMaxLinkSpeed;
/** Offset 0x02FB - DMI Equalization Phase 2
DMI Equalization Phase 2. (0x0): Disable phase 2, (0x1): Enable phase 2, (0x2)(Default):
AUTO - Use the current default method
0:Disable phase2, 1:Enable phase2, 2:Auto
**/
UINT8 DmiGen3EqPh2Enable;
/** Offset 0x02FC - DMI Gen3 Equalization Phase3
DMI Gen3 Equalization Phase3. Auto(0x0)(Default): Use the current default method,
HwEq(0x1): Use Adaptive Hardware Equalization, SwEq(0x2): Use Adaptive Software
Equalization (Implemented in BIOS Reference Code), Static(0x3): Use the Static
EQs provided in DmiGen3EndPointPreset array for Phase1 AND Phase3 (Instead of just
Phase1), Disabled(0x4): Bypass Equalization Phase 3
0:Auto, 1:HwEq, 2:SwEq, 3:StaticEq, 4:BypassPhase3
**/
UINT8 DmiGen3EqPh3Method;
/** Offset 0x02FD - Enable/Disable DMI GEN3 Static EQ Phase1 programming
Program DMI Gen3 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static
Presets Programming, Enabled(0x1)(Default): Enable EQ Phase1 Static Presets Programming
$EN_DIS
**/
UINT8 DmiGen3ProgramStaticEq;
/** Offset 0x02FE - DeEmphasis control for DMI
DeEmphasis control for DMI. 0=-6dB, 1(Default)=-3.5 dB
0: -6dB, 1: -3.5dB
**/
UINT8 DmiDeEmphasis;
/** Offset 0x02FF - DMI Gen3 Root port preset values per lane
Used for programming DMI Gen3 preset values per lane. Range: 0-9, 8 is default for each lane
**/
UINT8 DmiGen3RootPortPreset[8];
/** Offset 0x0307 - DMI Gen3 End port preset values per lane
Used for programming DMI Gen3 preset values per lane. Range: 0-9, 7 is default for each lane
**/
UINT8 DmiGen3EndPointPreset[8];
/** Offset 0x030F - DMI Gen3 End port Hint values per lane
Used for programming DMI Gen3 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
UINT8 DmiGen3EndPointHint[8];
/** Offset 0x0317 - DMI Gen3 RxCTLEp per-Bundle control
Range: 0-15, 0 is default for each bundle, must be specified based upon platform design
**/
UINT8 DmiGen3RxCtlePeaking[4];
/** Offset 0x031B - BIST on Reset
Enable or Disable BIST on Reset; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 BistOnReset;
/** Offset 0x031C - Skip Stop PBET Timer Enable/Disable
Skip Stop PBET Timer; <b>0: Disable</b>; 1: Enable
$EN_DIS
**/
UINT8 SkipStopPbet;
/** Offset 0x031D - C6DRAM power gating feature
This policy indicates whether or not BIOS should allocate PRMRR memory for C6DRAM
power gating feature.- 0: Don't allocate any PRMRR memory for C6DRAM power gating
feature.- <b>1: Allocate PRMRR memory for C6DRAM power gating feature</b>.
$EN_DIS
**/
UINT8 EnableC6Dram;
/** Offset 0x031E - Over clocking support
Over clocking support; <b>0: Disable</b>; 1: Enable
$EN_DIS
**/
UINT8 OcSupport;
/** Offset 0x031F - Over clocking Lock
Over clocking Lock Enable/Disable; 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 OcLock;
/** Offset 0x0320 - Maximum Core Turbo Ratio Override
Maximum core turbo ratio override allows to increase CPU core frequency beyond the
fused max turbo ratio limit. <b>0: Hardware defaults.</b> Range: 0-85
**/
UINT8 CoreMaxOcRatio;
/** Offset 0x0321 - Core voltage mode
Core voltage mode; <b>0: Adaptive</b>; 1: Override.
$EN_DIS
**/
UINT8 CoreVoltageMode;
/** Offset 0x0322 - Maximum clr turbo ratio override
Maximum clr turbo ratio override allows to increase CPU clr frequency beyond the
fused max turbo ratio limit. <b>0: Hardware defaults.</b> Range: 0-85
**/
UINT8 RingMaxOcRatio;
/** Offset 0x0323 - Hyper Threading Enable/Disable
Enable or Disable Hyper Threading; 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 HyperThreading;
/** Offset 0x0324 - Enable or Disable CPU Ratio Override
Enable or Disable CPU Ratio Override; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 CpuRatioOverride;
/** Offset 0x0325 - CPU ratio value
CPU ratio value. Valid Range 0 to 63
**/
UINT8 CpuRatio;
/** Offset 0x0326 - Boot frequency
Sets the boot frequency starting from reset vector.- 0: Maximum battery performance.
1: Maximum non-turbo performance. <b>2: Turbo performance </b>
0:0, 1:1, 2:2
**/
UINT8 BootFrequency;
/** Offset 0x0327 - Number of active cores
Number of active cores(Depends on Number of cores). <b>0: All</b>;<b>1: 1 </b>;<b>2:
2 </b>;<b>3: 3 </b>
0:All, 1:1, 2:2, 3:3
**/
UINT8 ActiveCoreCount;
/** Offset 0x0328 - Processor Early Power On Configuration FCLK setting
<b>0: 800 MHz (ULT/ULX)</b>. <b>1: 1 GHz (DT/Halo)</b>. Not supported on ULT/ULX.-
2: 400 MHz. - 3: Reserved
0:800 MHz, 1: 1 GHz, 2: 400 MHz, 3: Reserved
**/
UINT8 FClkFrequency;
/** Offset 0x0329 - Set JTAG power in C10 and deeper power states
False: JTAG is power gated in C10 state. True: keeps the JTAG power up during C10
and deeper power states for debug purpose. <b>0: False</b>; 1: True.
0: False, 1: True
**/
UINT8 JtagC10PowerGateDisable;
/** Offset 0x032A - Enable or Disable VMX
Enable or Disable VMX; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 VmxEnable;
/** Offset 0x032B - AVX2 Ratio Offset
0(Default)= No Offset. Range 0 - 31. Specifies number of bins to decrease AVX ratio
vs. Core Ratio. Uses Mailbox MSR 0x150, cmd 0x1B.
**/
UINT8 Avx2RatioOffset;
/** Offset 0x032C - AVX3 Ratio Offset
0(Default)= No Offset. Range 0 - 31. Specifies number of bins to decrease AVX ratio
vs. Core Ratio. Uses Mailbox MSR 0x150, cmd 0x1B.
**/
UINT8 Avx3RatioOffset;
/** Offset 0x032D - BCLK Adaptive Voltage Enable
When enabled, the CPU V/F curves are aware of BCLK frequency when calculated. </b>0:
Disable;<b> 1: Enable
$EN_DIS
**/
UINT8 BclkAdaptiveVoltage;
/** Offset 0x032E - core voltage override
The core voltage override which is applied to the entire range of cpu core frequencies.
Valid Range 0 to 2000
**/
UINT16 CoreVoltageOverride;
/** Offset 0x0330 - Core Turbo voltage Adaptive
Extra Turbo voltage applied to the cpu core when the cpu is operating in turbo mode.
Valid Range 0 to 2000
**/
UINT16 CoreVoltageAdaptive;
/** Offset 0x0332 - Core Turbo voltage Offset
The voltage offset applied to the core while operating in turbo mode.Valid Range 0 to 1000
**/
UINT16 CoreVoltageOffset;
/** Offset 0x0334 - Core PLL voltage offset
Core PLL voltage offset. <b>0: No offset</b>. Range 0-63
**/
UINT8 CorePllVoltageOffset;
/** Offset 0x0335 - Ring Downbin
Ring Downbin enable/disable. When enabled, CPU will ensure the ring ratio is always
lower than the core ratio.0: Disable; <b>1: Enable.</b>
$EN_DIS
**/
UINT8 RingDownBin;
/** Offset 0x0336 - Ring voltage mode
Ring voltage mode; <b>0: Adaptive</b>; 1: Override.
$EN_DIS
**/
UINT8 RingVoltageMode;
/** Offset 0x0337 - TjMax Offset
TjMax offset.Specified value here is clipped by pCode (125 - TjMax Offset) to support
TjMax in the range of 62 to 115 deg Celsius. Valid Range 10 - 63
**/
UINT8 TjMaxOffset;
/** Offset 0x0338 - Ring voltage override
The ring voltage override which is applied to the entire range of cpu ring frequencies.
Valid Range 0 to 2000
**/
UINT16 RingVoltageOverride;
/** Offset 0x033A - Ring Turbo voltage Adaptive
Extra Turbo voltage applied to the cpu ring when the cpu is operating in turbo mode.
Valid Range 0 to 2000
**/
UINT16 RingVoltageAdaptive;
/** Offset 0x033C - Ring Turbo voltage Offset
The voltage offset applied to the ring while operating in turbo mode. Valid Range 0 to 1000
**/
UINT16 RingVoltageOffset;
/** Offset 0x033E - Enable or Disable TME
Enable or Disable TME; <b>0: Disable<b>; 1: Enable.
$EN_DIS
**/
UINT8 TmeEnable;
/** Offset 0x033F - Enable CPU CrashLog
Enable or Disable CPU CrashLog; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 CpuCrashLogEnable;
/** Offset 0x0340 - ElixirSpringsPatchAddr
DEPRECATED
**/
UINT32 ElixirSpringsPatchAddr;
/** Offset 0x0344 - ElixirSpringsPatchSize
DEPRECATED
**/
UINT32 ElixirSpringsPatchSize;
/** Offset 0x0348 - CPU Run Control
Enable, Disable or Do not configure CPU Run Control; 0: Disable; 1: Enable ; <b>2:
No Change</b>
0:Disabled, 1:Enabled, 2:No Change
**/
UINT8 DebugInterfaceEnable;
/** Offset 0x0349 - CPU Run Control Lock
Lock or Unlock CPU Run Control; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 DebugInterfaceLockEnable;
/** Offset 0x034A - BiosGuard
Enable/Disable. 0: Disable, Enable/Disable BIOS Guard feature, 1: enable
$EN_DIS
**/
UINT8 BiosGuard;
/** Offset 0x034B
**/
UINT8 BiosGuardToolsInterface;
/** Offset 0x034C - EnableSgx
Enable/Disable. 0: Disable, Enable/Disable SGX feature, 1: enable, 2: Software Control
0: Disable, 1: Enable, 2: Software Control
**/
UINT8 EnableSgx;
/** Offset 0x034D - Txt
Enable/Disable. 0: Disable, Enable/Disable Txt feature, 1: enable
$EN_DIS
**/
UINT8 Txt;
/** Offset 0x034E
**/
UINT8 UnusedUpdSpace10[2];
/** Offset 0x0350 - PrmrrSize
Enable/Disable. 0: Disable, define default value of PrmrrSize , 1: enable
**/
UINT32 PrmrrSize;
/** Offset 0x0354 - SinitMemorySize
Enable/Disable. 0: Disable, define default value of SinitMemorySize , 1: enable
**/
UINT32 SinitMemorySize;
/** Offset 0x0358 - TxtDprMemoryBase
Enable/Disable. 0: Disable, define default value of TxtDprMemoryBase , 1: enable
**/
UINT64 TxtDprMemoryBase;
/** Offset 0x0360 - TxtHeapMemorySize
Enable/Disable. 0: Disable, define default value of TxtHeapMemorySize , 1: enable
**/
UINT32 TxtHeapMemorySize;
/** Offset 0x0364 - TxtDprMemorySize
Enable/Disable. 0: Disable, define default value of TxtDprMemorySize , 1: enable
**/
UINT32 TxtDprMemorySize;
/** Offset 0x0368 - BiosAcmBase
Enable/Disable. 0: Disable, define default value of BiosAcmBase , 1: enable
**/
UINT32 BiosAcmBase;
/** Offset 0x036C - BiosAcmSize
Enable/Disable. 0: Disable, define default value of BiosAcmSize , 1: enable
**/
UINT32 BiosAcmSize;
/** Offset 0x0370 - ApStartupBase
Enable/Disable. 0: Disable, define default value of BiosAcmBase , 1: enable
**/
UINT32 ApStartupBase;
/** Offset 0x0374 - TgaSize
Enable/Disable. 0: Disable, define default value of TgaSize , 1: enable
**/
UINT32 TgaSize;
/** Offset 0x0378 - TxtLcpPdBase
Enable/Disable. 0: Disable, define default value of TxtLcpPdBase , 1: enable
**/
UINT64 TxtLcpPdBase;
/** Offset 0x0380 - TxtLcpPdSize
Enable/Disable. 0: Disable, define default value of TxtLcpPdSize , 1: enable
**/
UINT64 TxtLcpPdSize;
/** Offset 0x0388 - IsTPMPresence
IsTPMPresence default values
**/
UINT8 IsTPMPresence;
/** Offset 0x0389 - Configuration for boot TDP selection
Configuration for boot TDP selection; <b>0: TDP Nominal</b>; 1: TDP Down; 2: TDP
Up;0xFF : Deactivate
**/
UINT8 ConfigTdpLevel;
/** Offset 0x038A - ReservedSecurityPreMem
Reserved for Security Pre-Mem
$EN_DIS
**/
UINT8 ReservedSecurityPreMem[5];
/** Offset 0x038F - Enable PCH HSIO PCIE Rx Set Ctle
Enable PCH PCIe Gen 3 Set CTLE Value.
**/
UINT8 PchPcieHsioRxSetCtleEnable[24];
/** Offset 0x03A7 - PCH HSIO PCIE Rx Set Ctle Value
PCH PCIe Gen 3 Set CTLE Value.
**/
UINT8 PchPcieHsioRxSetCtle[24];
/** Offset 0x03BF - Enble PCH HSIO PCIE TX Gen 1 Downscale Amplitude Adjustment value override
0: Disable; 1: Enable.
**/
UINT8 PchPcieHsioTxGen1DownscaleAmpEnable[24];
/** Offset 0x03D7 - PCH HSIO PCIE Gen 2 TX Output Downscale Amplitude Adjustment value
PCH PCIe Gen 2 TX Output Downscale Amplitude Adjustment value.
**/
UINT8 PchPcieHsioTxGen1DownscaleAmp[24];
/** Offset 0x03EF - Enable PCH HSIO PCIE TX Gen 2 Downscale Amplitude Adjustment value override
0: Disable; 1: Enable.
**/
UINT8 PchPcieHsioTxGen2DownscaleAmpEnable[24];
/** Offset 0x0407 - PCH HSIO PCIE Gen 2 TX Output Downscale Amplitude Adjustment value
PCH PCIe Gen 2 TX Output Downscale Amplitude Adjustment value.
**/
UINT8 PchPcieHsioTxGen2DownscaleAmp[24];
/** Offset 0x041F - Enable PCH HSIO PCIE TX Gen 3 Downscale Amplitude Adjustment value override
0: Disable; 1: Enable.
**/
UINT8 PchPcieHsioTxGen3DownscaleAmpEnable[24];
/** Offset 0x0437 - PCH HSIO PCIE Gen 3 TX Output Downscale Amplitude Adjustment value
PCH PCIe Gen 3 TX Output Downscale Amplitude Adjustment value.
**/
UINT8 PchPcieHsioTxGen3DownscaleAmp[24];
/** Offset 0x044F - Enable PCH HSIO PCIE Gen 1 TX Output De-Emphasis Adjustment Setting value override
0: Disable; 1: Enable.
**/
UINT8 PchPcieHsioTxGen1DeEmphEnable[24];
/** Offset 0x0467 - PCH HSIO PCIE Gen 1 TX Output De-Emphasis Adjustment value
PCH PCIe Gen 1 TX Output De-Emphasis Adjustment Setting.
**/
UINT8 PchPcieHsioTxGen1DeEmph[24];
/** Offset 0x047F - Enable PCH HSIO PCIE Gen 2 TX Output -3.5dB De-Emphasis Adjustment Setting value override
0: Disable; 1: Enable.
**/
UINT8 PchPcieHsioTxGen2DeEmph3p5Enable[24];
/** Offset 0x0497 - PCH HSIO PCIE Gen 2 TX Output -3.5dB De-Emphasis Adjustment value
PCH PCIe Gen 2 TX Output -3.5dB De-Emphasis Adjustment Setting.
**/
UINT8 PchPcieHsioTxGen2DeEmph3p5[24];
/** Offset 0x04AF - Enable PCH HSIO PCIE Gen 2 TX Output -6.0dB De-Emphasis Adjustment Setting value override
0: Disable; 1: Enable.
**/
UINT8 PchPcieHsioTxGen2DeEmph6p0Enable[24];
/** Offset 0x04C7 - PCH HSIO PCIE Gen 2 TX Output -6.0dB De-Emphasis Adjustment value
PCH PCIe Gen 2 TX Output -6.0dB De-Emphasis Adjustment Setting.
**/
UINT8 PchPcieHsioTxGen2DeEmph6p0[24];
/** Offset 0x04DF - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioRxGen1EqBoostMagEnable[8];
/** Offset 0x04E7 - PCH HSIO SATA 1.5 Gb/s Receiver Equalization Boost Magnitude Adjustment value
PCH HSIO SATA 1.5 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
UINT8 PchSataHsioRxGen1EqBoostMag[8];
/** Offset 0x04EF - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioRxGen2EqBoostMagEnable[8];
/** Offset 0x04F7 - PCH HSIO SATA 3.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value
PCH HSIO SATA 3.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
UINT8 PchSataHsioRxGen2EqBoostMag[8];
/** Offset 0x04FF - Enable PCH HSIO SATA Receiver Equalization Boost Magnitude Adjustment Value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioRxGen3EqBoostMagEnable[8];
/** Offset 0x0507 - PCH HSIO SATA 6.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value
PCH HSIO SATA 6.0 Gb/s Receiver Equalization Boost Magnitude Adjustment value.
**/
UINT8 PchSataHsioRxGen3EqBoostMag[8];
/** Offset 0x050F - Enable PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioTxGen1DownscaleAmpEnable[8];
/** Offset 0x0517 - PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value
PCH HSIO SATA 1.5 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
UINT8 PchSataHsioTxGen1DownscaleAmp[8];
/** Offset 0x051F - Enable PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioTxGen2DownscaleAmpEnable[8];
/** Offset 0x0527 - PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value
PCH HSIO SATA 3.0 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
UINT8 PchSataHsioTxGen2DownscaleAmp[8];
/** Offset 0x052F - Enable PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioTxGen3DownscaleAmpEnable[8];
/** Offset 0x0537 - PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value
PCH HSIO SATA 6.0 Gb/s TX Output Downscale Amplitude Adjustment value.
**/
UINT8 PchSataHsioTxGen3DownscaleAmp[8];
/** Offset 0x053F - Enable PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioTxGen1DeEmphEnable[8];
/** Offset 0x0547 - PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting
PCH HSIO SATA 1.5 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
UINT8 PchSataHsioTxGen1DeEmph[8];
/** Offset 0x054F - Enable PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioTxGen2DeEmphEnable[8];
/** Offset 0x0557 - PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting
PCH HSIO SATA 3.0 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
UINT8 PchSataHsioTxGen2DeEmph[8];
/** Offset 0x055F - Enable PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting value override
0: Disable; 1: Enable.
**/
UINT8 PchSataHsioTxGen3DeEmphEnable[8];
/** Offset 0x0567 - PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting
PCH HSIO SATA 6.0 Gb/s TX Output De-Emphasis Adjustment Setting.
**/
UINT8 PchSataHsioTxGen3DeEmph[8];
/** Offset 0x056F - PCH LPC Enhanced Port 80 Decoding
Original LPC only decodes one byte of port 80h.
$EN_DIS
**/
UINT8 PchLpcEnhancePort8xhDecoding;
/** Offset 0x0570 - PCH Port80 Route
Control where the Port 80h cycles are sent, 0: LPC; 1: PCI.
0:LPC, 1:PCI
**/
UINT8 PchPort80Route;
/** Offset 0x0571 - Enable SMBus ARP support
Enable SMBus ARP support.
$EN_DIS
**/
UINT8 SmbusArpEnable;
/** Offset 0x0572 - Number of RsvdSmbusAddressTable.
The number of elements in the RsvdSmbusAddressTable.
**/
UINT8 PchNumRsvdSmbusAddresses;
/** Offset 0x0573
**/
UINT8 UnusedUpdSpace11;
/** Offset 0x0574 - SMBUS Base Address
SMBUS Base Address (IO space).
**/
UINT16 PchSmbusIoBase;
/** Offset 0x0576 - Enable SMBus Alert Pin
Enable SMBus Alert Pin.
$EN_DIS
**/
UINT8 PchSmbAlertEnable;
/** Offset 0x0577 - Usage type for ClkSrc
0-23: PCH rootport, 0x40-0x43: PEG port, 0x70:LAN, 0x80: unspecified but in use
(free running), 0xFF: not used
**/
UINT8 PcieClkSrcUsage[16];
/** Offset 0x0587 - ClkReq-to-ClkSrc mapping
Number of ClkReq signal assigned to ClkSrc
**/
UINT8 PcieClkSrcClkReq[16];
/** Offset 0x0597
**/
UINT8 UnusedUpdSpace12;
/** Offset 0x0598 - Point of RsvdSmbusAddressTable
Array of addresses reserved for non-ARP-capable SMBus devices.
**/
UINT32 RsvdSmbusAddressTablePtr;
/** Offset 0x059C - Enable PCIE RP Mask
Enable/disable PCIE Root Ports. 0: disable, 1: enable. One bit for each port, bit0
for port1, bit1 for port2, and so on.
**/
UINT32 PcieRpEnableMask;
/** Offset 0x05A0 - Debug Interfaces
Debug Interfaces. BIT0-RAM, BIT1-UART, BIT3-USB3, BIT4-Serial IO, BIT5-TraceHub,
BIT2 - Not used.
**/
UINT8 PcdDebugInterfaceFlags;
/** Offset 0x05A1 - Serial Io Uart Debug Controller Number
Select SerialIo Uart Controller for debug. Note: If UART0 is selected as CNVi BT
Core interface, it cannot be used for debug purpose.
0:SerialIoUart0, 1:SerialIoUart1, 2:SerialIoUart2
**/
UINT8 SerialIoUartDebugControllerNumber;
/** Offset 0x05A2 - Serial Io Uart Debug Auto Flow
Enables UART hardware flow control, CTS and RTS lines.
$EN_DIS
**/
UINT8 SerialIoUartDebugAutoFlow;
/** Offset 0x05A3
**/
UINT8 UnusedUpdSpace13;
/** Offset 0x05A4 - Serial Io Uart Debug BaudRate
Set default BaudRate Supported from 0 - default to 6000000. Recommended values 9600,
19200, 57600, 115200, 460800, 921600, 1500000, 1843200, 3000000, 3686400, 6000000
**/
UINT32 SerialIoUartDebugBaudRate;
/** Offset 0x05A8 - Serial Io Uart Debug Parity
Set default Parity.
0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
**/
UINT8 SerialIoUartDebugParity;
/** Offset 0x05A9 - Serial Io Uart Debug Stop Bits
Set default stop bits.
0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3: TwoStopBits
**/
UINT8 SerialIoUartDebugStopBits;
/** Offset 0x05AA - Serial Io Uart Debug Data Bits
Set default word length. 0: Default, 5,6,7,8
5:5BITS, 6:6BITS, 7:7BITS, 8:8BITS
**/
UINT8 SerialIoUartDebugDataBits;
/** Offset 0x05AB
**/
UINT8 UnusedUpdSpace14;
/** Offset 0x05AC - Serial Io Uart Debug Mmio Base
Select SerialIo Uart default MMIO resource in SEC/PEI phase when PcdSerialIoUartMode
= SerialIoUartPci.
**/
UINT32 SerialIoUartDebugMmioBase;
/** Offset 0x05B0 - ISA Serial Base selection
Select ISA Serial Base address. Default is 0x3F8.
0:0x3F8, 1:0x2F8
**/
UINT8 PcdIsaSerialUartBase;
/** Offset 0x05B1 - GT PLL voltage offset
Core PLL voltage offset. <b>0: No offset</b>. Range 0-63
**/
UINT8 GtPllVoltageOffset;
/** Offset 0x05B2 - Ring PLL voltage offset
Core PLL voltage offset. <b>0: No offset</b>. Range 0-63
**/
UINT8 RingPllVoltageOffset;
/** Offset 0x05B3 - System Agent PLL voltage offset
Core PLL voltage offset. <b>0: No offset</b>. Range 0-63
**/
UINT8 SaPllVoltageOffset;
/** Offset 0x05B4 - Memory Controller PLL voltage offset
Core PLL voltage offset. <b>0: No offset</b>. Range 0-63
**/
UINT8 McPllVoltageOffset;
/** Offset 0x05B5 - MRC Safe Config
Enables/Disable MRC Safe Config
$EN_DIS
**/
UINT8 MrcSafeConfig;
/** Offset 0x05B6 - TCSS Thunderbolt PCIE Root Port 0 Enable
Set TCSS Thunderbolt PCIE Root Port 0. 0:Disabled 1:Enabled
$EN_DIS
**/
UINT8 TcssItbtPcie0En;
/** Offset 0x05B7 - TCSS Thunderbolt PCIE Root Port 1 Enable
Set TCSS Thunderbolt PCIE Root Port 1. 0:Disabled 1:Enabled
$EN_DIS
**/
UINT8 TcssItbtPcie1En;
/** Offset 0x05B8 - TCSS Thunderbolt PCIE Root Port 2 Enable
Set TCSS Thunderbolt PCIE Root Port 2. 0:Disabled 1:Enabled
$EN_DIS
**/
UINT8 TcssItbtPcie2En;
/** Offset 0x05B9 - TCSS Thunderbolt PCIE Root Port 3 Enable
Set TCSS Thunderbolt PCIE Root Port 3. 0:Disabled 1:Enabled
$EN_DIS
**/
UINT8 TcssItbtPcie3En;
/** Offset 0x05BA - TCSS USB HOST (xHCI) Enable
Set TCSS XHCI. 0:Disabled 1:Enabled - Must be enabled if xDCI is enabled below
$EN_DIS
**/
UINT8 TcssXhciEn;
/** Offset 0x05BB - TCSS USB DEVICE (xDCI) Enable
Set TCSS XDCI. 0:Disabled 1:Enabled - xHCI must be enabled if xDCI is enabled
$EN_DIS
**/
UINT8 TcssXdciEn;
/** Offset 0x05BC - TCSS DMA0 Enable
Set TCSS DMA0. 0:Disabled 1:Enabled
$EN_DIS
**/
UINT8 TcssDma0En;
/** Offset 0x05BD - TCSS DMA1 Enable
Set TCSS DMA1. 0:Disabled 1:Enabled
$EN_DIS
**/
UINT8 TcssDma1En;
/** Offset 0x05BE - PcdSerialDebugBaudRate
Baud Rate for Serial Debug Messages. 3:9600, 4:19200, 6:56700, 7:115200.
3:9600, 4:19200, 6:56700, 7:115200
**/
UINT8 PcdSerialDebugBaudRate;
/** Offset 0x05BF - HobBufferSize
Size to set HOB Buffer. 0:Default, 1: 1 Byte, 2: 1 KB, 3: Max value(assuming 63KB
total HOB size).
0:Default, 1: 1 Byte, 2: 1 KB, 3: Max value
**/
UINT8 HobBufferSize;
/** Offset 0x05C0 - Early Command Training
Enables/Disable Early Command Training
$EN_DIS
**/
UINT8 ECT;
/** Offset 0x05C1 - SenseAmp Offset Training
Enables/Disable SenseAmp Offset Training
$EN_DIS
**/
UINT8 SOT;
/** Offset 0x05C2 - Early ReadMPR Timing Centering 2D
Enables/Disable Early ReadMPR Timing Centering 2D
$EN_DIS
**/
UINT8 ERDMPRTC2D;
/** Offset 0x05C3 - Read MPR Training
Enables/Disable Read MPR Training
$EN_DIS
**/
UINT8 RDMPRT;
/** Offset 0x05C4 - Receive Enable Training
Enables/Disable Receive Enable Training
$EN_DIS
**/
UINT8 RCVET;
/** Offset 0x05C5 - Jedec Write Leveling
Enables/Disable Jedec Write Leveling
$EN_DIS
**/
UINT8 JWRL;
/** Offset 0x05C6 - Early Write Time Centering 2D
Enables/Disable Early Write Time Centering 2D
$EN_DIS
**/
UINT8 EWRTC2D;
/** Offset 0x05C7 - Early Read Time Centering 2D
Enables/Disable Early Read Time Centering 2D
$EN_DIS
**/
UINT8 ERDTC2D;
/** Offset 0x05C8 - Write Timing Centering 1D
Enables/Disable Write Timing Centering 1D
$EN_DIS
**/
UINT8 WRTC1D;
/** Offset 0x05C9 - Write Voltage Centering 1D
Enables/Disable Write Voltage Centering 1D
$EN_DIS
**/
UINT8 WRVC1D;
/** Offset 0x05CA - Read Timing Centering 1D
Enables/Disable Read Timing Centering 1D
$EN_DIS
**/
UINT8 RDTC1D;
/** Offset 0x05CB - Dimm ODT Training
Enables/Disable Dimm ODT Training
$EN_DIS
**/
UINT8 DIMMODTT;
/** Offset 0x05CC - DIMM RON Training
Enables/Disable DIMM RON Training
$EN_DIS
**/
UINT8 DIMMRONT;
/** Offset 0x05CD - Write Drive Strength/Equalization 2D
Enables/Disable Write Drive Strength/Equalization 2D
$EN_DIS
**/
UINT8 WRDSEQT;
/** Offset 0x05CE - Write Slew Rate Training
Enables/Disable Write Slew Rate Training
$EN_DIS
**/
UINT8 WRSRT;
/** Offset 0x05CF - Read ODT Training
Enables/Disable Read ODT Training
$EN_DIS
**/
UINT8 RDODTT;
/** Offset 0x05D0 - Read Equalization Training
Enables/Disable Read Equalization Training
$EN_DIS
**/
UINT8 RDEQT;
/** Offset 0x05D1 - Read Amplifier Training
Enables/Disable Read Amplifier Training
$EN_DIS
**/
UINT8 RDAPT;
/** Offset 0x05D2 - Write Timing Centering 2D
Enables/Disable Write Timing Centering 2D
$EN_DIS
**/
UINT8 WRTC2D;
/** Offset 0x05D3 - Read Timing Centering 2D
Enables/Disable Read Timing Centering 2D
$EN_DIS
**/
UINT8 RDTC2D;
/** Offset 0x05D4 - Write Voltage Centering 2D
Enables/Disable Write Voltage Centering 2D
$EN_DIS
**/
UINT8 WRVC2D;
/** Offset 0x05D5 - Read Voltage Centering 2D
Enables/Disable Read Voltage Centering 2D
$EN_DIS
**/
UINT8 RDVC2D;
/** Offset 0x05D6 - Command Voltage Centering
Enables/Disable Command Voltage Centering
$EN_DIS
**/
UINT8 CMDVC;
/** Offset 0x05D7 - Late Command Training
Enables/Disable Late Command Training
$EN_DIS
**/
UINT8 LCT;
/** Offset 0x05D8 - Round Trip Latency Training
Enables/Disable Round Trip Latency Training
$EN_DIS
**/
UINT8 RTL;
/** Offset 0x05D9 - Turn Around Timing Training
Enables/Disable Turn Around Timing Training
$EN_DIS
**/
UINT8 TAT;
/** Offset 0x05DA - Memory Test
Enables/Disable Memory Test
$EN_DIS
**/
UINT8 MEMTST;
/** Offset 0x05DB - DIMM SPD Alias Test
Enables/Disable DIMM SPD Alias Test
$EN_DIS
**/
UINT8 ALIASCHK;
/** Offset 0x05DC - Receive Enable Centering 1D
Enables/Disable Receive Enable Centering 1D
$EN_DIS
**/
UINT8 RCVENC1D;
/** Offset 0x05DD - Retrain Margin Check
Enables/Disable Retrain Margin Check
$EN_DIS
**/
UINT8 RMC;
/** Offset 0x05DE - Write Drive Strength Up/Dn independently
Enables/Disable Write Drive Strength Up/Dn independently
$EN_DIS
**/
UINT8 WRDSUDT;
/** Offset 0x05DF - ECC Support
Enables/Disable ECC Support
$EN_DIS
**/
UINT8 EccSupport;
/** Offset 0x05E0 - Ibecc
In-Band ECC Support
$EN_DIS
**/
UINT8 Ibecc;
/** Offset 0x05E1 - IbeccParity
In-Band ECC Parity Control
$EN_DIS
**/
UINT8 IbeccParity;
/** Offset 0x05E2 - IbeccOperationMode
In-Band ECC Operation Mode
0:Protect base on address range, 1: Non-protected, 2: All protected
**/
UINT8 IbeccOperationMode;
/** Offset 0x05E3 - IbeccProtectedRegionEnable
In-Band ECC Protected Region Enable
$EN_DIS
**/
UINT8 IbeccProtectedRegionEnable[8];
/** Offset 0x05EB
**/
UINT8 UnusedUpdSpace15[1];
/** Offset 0x05EC - IbeccProtectedRegionBases
IBECC Protected Region Bases
**/
UINT16 IbeccProtectedRegionBase[8];
/** Offset 0x05FC - IbeccProtectedRegionMasks
IBECC Protected Region Masks
**/
UINT16 IbeccProtectedRegionMask[8];
/** Offset 0x060C - Memory Remap
Enables/Disable Memory Remap
$EN_DIS
**/
UINT8 RemapEnable;
/** Offset 0x060D - Rank Interleave support
Enables/Disable Rank Interleave support. NOTE: RI and HORI can not be enabled at
the same time.
$EN_DIS
**/
UINT8 RankInterleave;
/** Offset 0x060E - Enhanced Interleave support
Enables/Disable Enhanced Interleave support
$EN_DIS
**/
UINT8 EnhancedInterleave;
/** Offset 0x060F - Ch Hash Support
Enable/Disable Channel Hash Support. NOTE: ONLY if Memory interleaved Mode
$EN_DIS
**/
UINT8 ChHashEnable;
/** Offset 0x0610 - Extern Therm Status
Enables/Disable Extern Therm Status
$EN_DIS
**/
UINT8 EnableExtts;
/** Offset 0x0611 - DDR PowerDown and idle counter
Enables/Disable DDR PowerDown and idle counter(For LPDDR Only)
$EN_DIS
**/
UINT8 EnablePwrDn;
/** Offset 0x0612 - DDR PowerDown and idle counter
Enables/Disable DDR PowerDown and idle counter(For LPDDR Only)
$EN_DIS
**/
UINT8 EnablePwrDnLpddr;
/** Offset 0x0613 - SelfRefresh Enable
Enables/Disable SelfRefresh Enable
$EN_DIS
**/
UINT8 SrefCfgEna;
/** Offset 0x0614 - Throttler CKEMin Defeature
Enables/Disable Throttler CKEMin Defeature(For LPDDR Only)
$EN_DIS
**/
UINT8 ThrtCkeMinDefeatLpddr;
/** Offset 0x0615 - Throttler CKEMin Defeature
Enables/Disable Throttler CKEMin Defeature
$EN_DIS
**/
UINT8 ThrtCkeMinDefeat;
/** Offset 0x0616 - Enable RH Prevention
Enables/Disable RH Prevention
$EN_DIS
**/
UINT8 RhPrevention;
/** Offset 0x0617 - Exit On Failure (MRC)
Enables/Disable Exit On Failure (MRC)
$EN_DIS
**/
UINT8 ExitOnFailure;
/** Offset 0x0618 - New Features 1 - MRC
New Feature Enabling 1, <b>0:Disable</b>, 1:Enable
0:Disable, 1:Enable
**/
UINT8 NewFeatureEnable1;
/** Offset 0x0619 - New Features 2 - MRC
New Feature Enabling 2, <b>0:Disable</b>, 1:Enable
0:Disable, 1:Enable
**/
UINT8 NewFeatureEnable2;
/** Offset 0x061A - Duty Cycle Correction Training
Enable/Disable Duty Cycle Correction Training
$EN_DIS
**/
UINT8 DCC;
/** Offset 0x061B - Read Voltage Centering 1D
Enable/Disable Read Voltage Centering 1D
$EN_DIS
**/
UINT8 RDVC1D;
/** Offset 0x061C - TxDqTCO Comp Training
Enable/Disable TxDqTCO Comp Training
$EN_DIS
**/
UINT8 TXTCO;
/** Offset 0x061D - ClkTCO Comp Training
Enable/Disable ClkTCO Comp Training
$EN_DIS
**/
UINT8 CLKTCO;
/** Offset 0x061E - CMD Slew Rate Training
Enable/Disable CMD Slew Rate Training
$EN_DIS
**/
UINT8 CMDSR;
/** Offset 0x061F - CMD Drive Strength and Tx Equalization
Enable/Disable CMD Drive Strength and Tx Equalization
$EN_DIS
**/
UINT8 CMDDSEQ;
/** Offset 0x0620 - DIMM CA ODT Training
Enable/Disable DIMM CA ODT Training
$EN_DIS
**/
UINT8 DIMMODTCA;
/** Offset 0x0621 - TxDqsTCO Comp Training
Enable/Disable TxDqsTCO Comp Training
$EN_DIS
**/
UINT8 TXTCODQS;
/** Offset 0x0622 - CMD/CTL Drive Strength Up/Dn 2D
Enable/Disable CMD/CTL Drive Strength Up/Dn 2D
$EN_DIS
**/
UINT8 CMDDRUD;
/** Offset 0x0623 - VccDLL Bypass Training
Enable/Disable VccDLL Bypass Training
$EN_DIS
**/
UINT8 VCCDLLBP;
/** Offset 0x0624 - PanicVttDnLp Training
Enable/Disable PanicVttDnLp Training
$EN_DIS
**/
UINT8 PVTTDNLP;
/** Offset 0x0625 - Read Vref Decap Training*
Enable/Disable Read Vref Decap Training*
$EN_DIS
**/
UINT8 RDVREFDC;
/** Offset 0x0626 - Vddq Training
Enable/Disable Vddq Training
$EN_DIS
**/
UINT8 VDDQT;
/** Offset 0x0627 - Rank Margin Tool Per Bit
Enable/Disable Rank Margin Tool Per Bit
$EN_DIS
**/
UINT8 RMTBIT;
/** Offset 0x0628 - Override Performance Downgrade for Mixed Memory
Disable/Enables Override Performance Downgrade for Mixed Memory
$EN_DIS
**/
UINT8 OverrideDowngradeForMixedMemory;
/** Offset 0x0629
**/
UINT8 Reserved2[1];
/** Offset 0x062A - Select if CLK0 is shared between Rank0 and Rank1 in DDR4 DDP
Select if CLK0 is shared between Rank0 and Rank1 in DDR4 DDP
$EN_DIS
**/
UINT8 Ddr4DdpSharedClock;
/** Offset 0x062B - Select if ZQ pin is shared between Rank0 and Rank1 in DDR4 DDP
ESelect if ZQ pin is shared between Rank0 and Rank1 in DDR4 DDP
$EN_DIS
**/
UINT8 Ddr4DdpSharedZq;
/** Offset 0x062C - Ch Hash Interleaved Bit
Select the BIT to be used for Channel Interleaved mode. NOTE: BIT7 will interlave
the channels at a 2 cacheline granularity, BIT8 at 4 and BIT9 at 8. Default is BIT8
0:BIT6, 1:BIT7, 2:BIT8, 3:BIT9, 4:BIT10, 5:BIT11, 6:BIT12, 7:BIT13
**/
UINT8 ChHashInterleaveBit;
/** Offset 0x062D
**/
UINT8 UnusedUpdSpace16;
/** Offset 0x062E - Ch Hash Mask
Set the BIT(s) to be included in the XOR function. NOTE BIT mask corresponds to
BITS [19:6] Default is 0x0830
**/
UINT16 ChHashMask;
/** Offset 0x0630 - Base reference clock value
Base reference clock value, in Hertz(Default is 100Hz)
100000000:100Hz, 125000000:125Hz, 167000000:167Hz, 250000000:250Hz
**/
UINT32 BClkFrequency;
/** Offset 0x0634 - EPG DIMM Idd3N
Active standby current (Idd3N) in milliamps from datasheet. Must be calculated on
a per DIMM basis. Default is 26
**/
UINT16 Idd3n;
/** Offset 0x0636 - EPG DIMM Idd3P
Active power-down current (Idd3P) in milliamps from datasheet. Must be calculated
on a per DIMM basis. Default is 11
**/
UINT16 Idd3p;
/** Offset 0x0638 - RH Activation Probability
RH Activation Probability, Probability value is 1/2^(inputvalue)
**/
UINT8 RhActProbability;
/** Offset 0x0639 - Idle Energy Mc0Ch0Dimm0
Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
UINT8 IdleEnergyMc0Ch0Dimm0;
/** Offset 0x063A - Idle Energy Mc0Ch0Dimm1
Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
UINT8 IdleEnergyMc0Ch0Dimm1;
/** Offset 0x063B - Idle Energy Mc0Ch1Dimm0
Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
UINT8 IdleEnergyMc0Ch1Dimm0;
/** Offset 0x063C - Idle Energy Mc0Ch1Dimm1
Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
UINT8 IdleEnergyMc0Ch1Dimm1;
/** Offset 0x063D - Idle Energy Mc1Ch0Dimm0
Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
UINT8 IdleEnergyMc1Ch0Dimm0;
/** Offset 0x063E - Idle Energy Mc1Ch0Dimm1
Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
UINT8 IdleEnergyMc1Ch0Dimm1;
/** Offset 0x063F - Idle Energy Mc1Ch1Dimm0
Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
UINT8 IdleEnergyMc1Ch1Dimm0;
/** Offset 0x0640 - Idle Energy Mc1Ch1Dimm1
Idle Energy Consumed for 1 clk w/dimm idle/cke on, range[63;0],(10= Def)
**/
UINT8 IdleEnergyMc1Ch1Dimm1;
/** Offset 0x0641 - PowerDown Energy Mc0Ch0Dimm0
PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
UINT8 PdEnergyMc0Ch0Dimm0;
/** Offset 0x0642 - PowerDown Energy Mc0Ch0Dimm1
PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
UINT8 PdEnergyMc0Ch0Dimm1;
/** Offset 0x0643 - PowerDown Energy Mc0Ch1Dimm0
PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
UINT8 PdEnergyMc0Ch1Dimm0;
/** Offset 0x0644 - PowerDown Energy Mc0Ch1Dimm1
PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
UINT8 PdEnergyMc0Ch1Dimm1;
/** Offset 0x0645 - PowerDown Energy Mc1Ch0Dimm0
PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
UINT8 PdEnergyMc1Ch0Dimm0;
/** Offset 0x0646 - PowerDown Energy Mc1Ch0Dimm1
PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
UINT8 PdEnergyMc1Ch0Dimm1;
/** Offset 0x0647 - PowerDown Energy Mc1Ch1Dimm0
PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
UINT8 PdEnergyMc1Ch1Dimm0;
/** Offset 0x0648 - PowerDown Energy Mc1Ch1Dimm1
PowerDown Energy Consumed w/dimm idle/cke off, range[63;0],(6= Def)
**/
UINT8 PdEnergyMc1Ch1Dimm1;
/** Offset 0x0649 - Activate Energy Mc0Ch0Dimm0
Activate Energy Contribution, range[255;0],(172= Def)
**/
UINT8 ActEnergyMc0Ch0Dimm0;
/** Offset 0x064A - Activate Energy Mc0Ch0Dimm1
Activate Energy Contribution, range[255;0],(172= Def)
**/
UINT8 ActEnergyMc0Ch0Dimm1;
/** Offset 0x064B - Activate Energy Mc0Ch1Dimm0
Activate Energy Contribution, range[255;0],(172= Def)
**/
UINT8 ActEnergyMc0Ch1Dimm0;
/** Offset 0x064C - Activate Energy Mc0Ch1Dimm1
Activate Energy Contribution, range[255;0],(172= Def)
**/
UINT8 ActEnergyMc0Ch1Dimm1;
/** Offset 0x064D - Activate Energy Mc1Ch0Dimm0
Activate Energy Contribution, range[255;0],(172= Def)
**/
UINT8 ActEnergyMc1Ch0Dimm0;
/** Offset 0x064E - Activate Energy Mc1Ch0Dimm1
Activate Energy Contribution, range[255;0],(172= Def)
**/
UINT8 ActEnergyMc1Ch0Dimm1;
/** Offset 0x064F - Activate Energy Mc1Ch1Dimm0
Activate Energy Contribution, range[255;0],(172= Def)
**/
UINT8 ActEnergyMc1Ch1Dimm0;
/** Offset 0x0650 - Activate Energy Mc1Ch1Dimm1
Activate Energy Contribution, range[255;0],(172= Def)
**/
UINT8 ActEnergyMc1Ch1Dimm1;
/** Offset 0x0651 - Read Energy Mc0Ch0Dimm0
Read Energy Contribution, range[255;0],(212= Def)
**/
UINT8 RdEnergyMc0Ch0Dimm0;
/** Offset 0x0652 - Read Energy Mc0Ch0Dimm1
Read Energy Contribution, range[255;0],(212= Def)
**/
UINT8 RdEnergyMc0Ch0Dimm1;
/** Offset 0x0653 - Read Energy Mc0Ch1Dimm0
Read Energy Contribution, range[255;0],(212= Def)
**/
UINT8 RdEnergyMc0Ch1Dimm0;
/** Offset 0x0654 - Read Energy Mc0Ch1Dimm1
Read Energy Contribution, range[255;0],(212= Def)
**/
UINT8 RdEnergyMc0Ch1Dimm1;
/** Offset 0x0655 - Read Energy Mc1Ch0Dimm0
Read Energy Contribution, range[255;0],(212= Def)
**/
UINT8 RdEnergyMc1Ch0Dimm0;
/** Offset 0x0656 - Read Energy Mc1Ch0Dimm1
Read Energy Contribution, range[255;0],(212= Def)
**/
UINT8 RdEnergyMc1Ch0Dimm1;
/** Offset 0x0657 - Read Energy Mc1Ch1Dimm0
Read Energy Contribution, range[255;0],(212= Def)
**/
UINT8 RdEnergyMc1Ch1Dimm0;
/** Offset 0x0658 - Read Energy Mc1Ch1Dimm1
Read Energy Contribution, range[255;0],(212= Def)
**/
UINT8 RdEnergyMc1Ch1Dimm1;
/** Offset 0x0659 - Write Energy Mc0Ch0Dimm0
Write Energy Contribution, range[255;0],(221= Def)
**/
UINT8 WrEnergyMc0Ch0Dimm0;
/** Offset 0x065A - Write Energy Mc0Ch0Dimm1
Write Energy Contribution, range[255;0],(221= Def)
**/
UINT8 WrEnergyMc0Ch0Dimm1;
/** Offset 0x065B - Write Energy Mc0Ch1Dimm0
Write Energy Contribution, range[255;0],(221= Def)
**/
UINT8 WrEnergyMc0Ch1Dimm0;
/** Offset 0x065C - Write Energy Mc0Ch1Dimm1
Write Energy Contribution, range[255;0],(221= Def)
**/
UINT8 WrEnergyMc0Ch1Dimm1;
/** Offset 0x065D - Write Energy Mc1Ch0Dimm0
Write Energy Contribution, range[255;0],(221= Def)
**/
UINT8 WrEnergyMc1Ch0Dimm0;
/** Offset 0x065E - Write Energy Mc1Ch0Dimm1
Write Energy Contribution, range[255;0],(221= Def)
**/
UINT8 WrEnergyMc1Ch0Dimm1;
/** Offset 0x065F - Write Energy Mc1Ch1Dimm0
Write Energy Contribution, range[255;0],(221= Def)
**/
UINT8 WrEnergyMc1Ch1Dimm0;
/** Offset 0x0660 - Write Energy Mc1Ch1Dimm1
Write Energy Contribution, range[255;0],(221= Def)
**/
UINT8 WrEnergyMc1Ch1Dimm1;
/** Offset 0x0661 - Throttler CKEMin Timer
Timer value for CKEMin, range[255;0]. Req'd min of SC_ROUND_T + BYTE_LENGTH (4).
Dfault is 0x00
**/
UINT8 ThrtCkeMinTmr;
/** Offset 0x0662 - Rapl Power Floor Ch0
Power budget ,range[255;0],(0= 5.3W Def)
**/
UINT8 RaplPwrFlCh0;
/** Offset 0x0663 - Rapl Power Floor Ch1
Power budget ,range[255;0],(0= 5.3W Def)
**/
UINT8 RaplPwrFlCh1;
/** Offset 0x0664 - Command Rate Support
CMD Rate and Limit Support Option. NOTE: ONLY supported in 1N Mode, Default is 3 CMDs
0:Disable, 5:2 CMDS, 7:3 CMDS, 9:4 CMDS, 11:5 CMDS, 13:6 CMDS, 15:7 CMDS
**/
UINT8 EnCmdRate;
/** Offset 0x0665 - REFRESH_2X_MODE
0- (Default)Disabled 1-iMC enables 2xRef when Warm and Hot 2- iMC enables 2xRef when Hot
0:Disable, 1:Enabled for WARM or HOT, 2:Enabled HOT only
**/
UINT8 Refresh2X;
/** Offset 0x0666 - Energy Performance Gain
Enable/disable(default) Energy Performance Gain.
$EN_DIS
**/
UINT8 EpgEnable;
/** Offset 0x0667 - Row Hammer Solution
Type of method used to prevent Row Hammer. Default is Hardware RHP
0:Hardware RHP, 1:2x Refresh
**/
UINT8 RhSolution;
/** Offset 0x0668 - User Manual Threshold
Disabled: Predefined threshold will be used.\n
Enabled: User Input will be used.
$EN_DIS
**/
UINT8 UserThresholdEnable;
/** Offset 0x0669 - User Manual Budget
Disabled: Configuration of memories will defined the Budget value.\n
Enabled: User Input will be used.
$EN_DIS
**/
UINT8 UserBudgetEnable;
/** Offset 0x066A - Power Down Mode
This option controls command bus tristating during idle periods
0x0:No Power Down, 0x1:APD, 0x6:PPD DLL OFF, 0xFF:Auto
**/
UINT8 PowerDownMode;
/** Offset 0x066B - Pwr Down Idle Timer
The minimum value should = to the worst case Roundtrip delay + Burst_Length. 0 means
AUTO: 64 for ULX/ULT, 128 for DT/Halo
**/
UINT8 PwdwnIdleCounter;
/** Offset 0x066C - Page Close Idle Timeout
This option controls Page Close Idle Timeout
0:Enabled, 1:Disabled
**/
UINT8 DisPgCloseIdleTimeout;
/** Offset 0x066D - Bitmask of ranks that have CA bus terminated
Offset 225 LPDDR4: Bitmask of ranks that have CA bus terminated. <b>0x01=Default,
Rank0 is terminating and Rank1 is non-terminating</b>
**/
UINT8 CmdRanksTerminated;
/** Offset 0x066E - PcdSerialDebugLevel
Serial Debug Message Level. 0:Disable, 1:Error Only, 2:Error & Warnings, 3:Load,
Error, Warnings & Info, 4:Load, Error, Warnings, Info & Event, 5:Load, Error, Warnings,
Info & Verbose.
0:Disable, 1:Error Only, 2:Error and Warnings, 3:Load Error Warnings and Info, 4:Load
Error Warnings and Info & Event, 5:Load Error Warnings Info and Verbose
**/
UINT8 PcdSerialDebugLevel;
/** Offset 0x066F - Fivr Faults
Fivr Faults; 0: Disabled; <b>1: Enabled.</b>
$EN_DIS
**/
UINT8 FivrFaults;
/** Offset 0x0670 - Fivr Efficiency
Fivr Efficiency Management; 0: Disabled; <b>1: Enabled.</b>
$EN_DIS
**/
UINT8 FivrEfficiency;
/** Offset 0x0671 - Safe Mode Support
This option configures the varous items in the IO and MC to be more conservative.(def=Disable)
$EN_DIS
**/
UINT8 SafeMode;
/** Offset 0x0672 - Ask MRC to clear memory content
Ask MRC to clear memory content <b>0: Do not Clear Memory;</b> 1: Clear Memory.
$EN_DIS
**/
UINT8 CleanMemory;
/** Offset 0x0673 - LpDdrDqDqsReTraining
Enables/Disable LpDdrDqDqsReTraining
$EN_DIS
**/
UINT8 LpDdrDqDqsReTraining;
/** Offset 0x0674 - TCSS USB Port Enable
Bitmap for per port enabling
**/
UINT8 UsbTcPortEnPreMem;
/** Offset 0x0675
**/
UINT8 UnusedUpdSpace17;
/** Offset 0x0676 - Post Code Output Port
This option configures Post Code Output Port
**/
UINT16 PostCodeOutputPort;
/** Offset 0x0678 - RMTLoopCount
Specifies the Loop Count to be used during Rank Margin Tool Testing. 0 - AUTO
**/
UINT8 RMTLoopCount;
/** Offset 0x0679 - Enable/Disable SA CRID
Enable: SA CRID, Disable (Default): SA CRID
$EN_DIS
**/
UINT8 CridEnable;
/** Offset 0x067A - WRC Feature
Enable/Disable WRC (Write Cache) feature of IOP. When feature is enabled, supports
IO devices allocating onto the ring and into LLC. WRC is fused on by default.
$EN_DIS
**/
UINT8 WrcFeatureEnable;
/** Offset 0x067B
**/
UINT8 UnusedUpdSpace18[1];
/** Offset 0x067C - BCLK RFI Frequency
Bclk RFI Frequency for each SAGV point in Hz units. 98000000Hz = 98MHz <b>0 - No
RFI Tuning</b>. Range is 98Mhz-100Mhz.
**/
UINT32 BclkRfiFreq[4];
/** Offset 0x068C - Size of PCIe IMR.
Size of PCIe IMR in megabytes
**/
UINT16 PcieImrSize;
/** Offset 0x068E - Enable PCIe IMR
0: Disable(AUTO), 1: Enable
$EN_DIS
**/
UINT8 PcieImrEnabled;
/** Offset 0x068F - Enable PCIe IMR
1: PCH PCIE, 2: SA PCIE. If PCIeImrEnabled is TRUE then this will use to select
the Root port location from PCH PCIe or SA PCIe
$EN_DIS
**/
UINT8 PcieImrRpLocation;
/** Offset 0x0690 - Root port number for IMR.
Root port number for IMR.If PCieImrRpLocation is PCH PCIe then select root port
from 0 to 23 and if it is SA PCIe then select root port from 0 to 3
**/
UINT8 PcieImrRpSelection;
/** Offset 0x0691 - SerialDebugMrcLevel
MRC Serial Debug Message Level. 0:Disable, 1:Error Only, 2:Error & Warnings, 3:Load,
Error, Warnings & Info, 4:Load, Error, Warnings, Info & Event, 5:Load, Error, Warnings,
Info & Verbose.
0:Disable, 1:Error Only, 2:Error and Warnings, 3:Load Error Warnings and Info, 4:Load
Error Warnings and Info & Event, 5:Load Error Warnings Info and Verbose
**/
UINT8 SerialDebugMrcLevel;
/** Offset 0x0692 - Mem Boot Mode
0: BOOT_MODE_1LM(Default), 1: BOOT_MODE_2LM, 2: BOOT_MODE_PROVISION
0: BOOT_MODE_1LM, 1: BOOT_MODE_2LM, 2: BOOT_MODE_PROVISION
**/
UINT8 MemBootMode;
/** Offset 0x0693 - PCIe ASPM programming will happen in relation to the Oprom
This option is specifically needed for ASPM configuration in 2LM feature
0:Disabled, 1:L0, 2:L1, 3:L0L1, 4:Auto
**/
UINT8 Peg3Aspm;
/** Offset 0x0694 - MFVC WRR VC Arbitration
0: DEFAULT_PHASES(Default), 1: PROGRAM_128PHASES
0: DEFAULT_PHASES, 1: PROGRAM_128PHASES
**/
UINT8 MfvcWrrArb;
/** Offset 0x0695 - BZM Support
1: enable, 0: disable(Default), Enable/disable setting for Boot-time Zero Memory support
$EN_DIS
**/
UINT8 BzmSupport;
/** Offset 0x0696 - VcId_7_0 values
Select VC ID for arbitration
**/
UINT8 VcId_7_0[16];
/** Offset 0x06A6 - Set Hw Parameters enable/disable
1: enable, 0: disable, Enable/disable setting of HW parameters
$EN_DIS
**/
UINT8 SetHwParameters;
/** Offset 0x06A7
**/
UINT8 UnusedUpdSpace19;
/** Offset 0x06A8 - LTR L1.2 Threshold Value
LTR L1.2 Threshold Value
**/
UINT16 Ltr_L1D2_ThVal;
/** Offset 0x06AA - LTR L1.2 Threshold Scale
LTR L1.2 Threshold Scale
**/
UINT8 Ltr_L1D2_ThScale;
/** Offset 0x06AB - system power state
system power state indicates the platform power state
**/
UINT8 SysPwrState;
/** Offset 0x06AC - Media Death Notification Enable/Disable
1: enable, 0: disable, Enable/disable for Media Death Notification
$EN_DIS
**/
UINT8 MediaDeathNotification;
/** Offset 0x06AD - Health Log Notification Enable/Disable
1: enable, 0: disable, Enable/disable for Health Log Notification
$EN_DIS
**/
UINT8 HealthLogNotification;
/** Offset 0x06AE - Temp crosses below TempThrottle Notification Enable/Disable
1: enable, 0: disable, Enable/disable for Temp crosses below TempThrottle Notification
$EN_DIS
**/
UINT8 TempBelowThrottleNotification;
/** Offset 0x06AF - Temp crosses above TempThrottle Notification Enable/Disable
1: enable, 0: disable, Enable/disable for Temp crosses above TempThrottle Notification
$EN_DIS
**/
UINT8 TempAboveThrottleNotification;
/** Offset 0x06B0 - Missing Commit Bit Notification Enable/Disable
1: enable, 0: disable, Enable/disable for Missing Commit Bit Notification
$EN_DIS
**/
UINT8 MissingCommitBitNotification;
/** Offset 0x06B1 - NVMeHoldDisableBit
1: enable, 0: disable, Enable/disable for NVMeHoldDisableBit
$EN_DIS
**/
UINT8 NVMeHoldDisableBit;
/** Offset 0x06B2 - Ddr4OneDpc
DDR4 1DPC performance feature for 2R DIMMs. Can be enabled on DIMM0 or DIMM1 only,
or on both (default)
0: Disabled, 1: Enabled on DIMM0 only, 2: Enabled on DIMM1 only, 3: Enabled
**/
UINT8 Ddr4OneDpc;
/** Offset 0x06B3 - Ch Hash Override POR settings
Enable/Disable Override Channel Hash Support POR values
$EN_DIS
**/
UINT8 ChHashOverride;
/** Offset 0x06B4 - PDA Enumeration
Enables/Disable PDA Enumeration
$EN_DIS
**/
UINT8 PDA;
/** Offset 0x06B5 - DPin Policy
Set DPin Policy. Internal Only:All display ports are for internal only. External
First:All display ports are for external only, if there is no External DP-In presence
presents then IOM will use all ports internal only
0: Internal Only, 1: External First
**/
UINT8 DpInExternalEn;
/** Offset 0x06B6 - DPin External Ports Number
Total number of External Gfx DpIn Port present on Board. Currently hardware wise
max 0x04 DpIn port supported, however DpIn module can handle upto 0x08 DpIn ports
**/
UINT8 NumberOfDpInPort;
/** Offset 0x06B7 - DPin External Port Connect Map
Indicate which Dp-In port connection detected. Each BIT stand for one Dp-In port.
**/
UINT8 DpInPortConnectMap;
/** Offset 0x06B8 - Command Pins Mapping
BitMask where bits [3:0] are Controller 0 Channel [3:0] and bits [7:4] are Controller
1 Channel [3:0]. 0 = CCC pin mapping is Ascending, 1 = CCC pin mapping is Descending.
**/
UINT8 Lp5CccConfig[4];
/** Offset 0x06BC - Command Pins Mirrored
BitMask where bits [3:0] are Controller 0 Channel [3:0] and bits [7:4] are Controller
1 Channel [3:0]. 0 = No Command Mirror and 1 = Command Mirror.
**/
UINT32 CmdMirror[1];
/** Offset 0x06C0 - CPU BCLK SSC Enable
Enable/Disable CPU BCLK Spread Spectrum. Default is Enabled.
$EN_DIS
**/
UINT8 CpuBclkSpread;
/** Offset 0x06C1 - McParity
CMI/MC Parity Control
$EN_DIS
**/
UINT8 McParity;
/** Offset 0x06C2 - Vddq Voltage Override
# is multiple of 1mV where 0 means Auto.
**/
UINT16 VddqVoltageOverride;
/** Offset 0x06C4 - Extended Bank Hashing
Eanble/Disable ExtendedBankHashing
$EN_DIS
**/
UINT8 ExtendedBankHashing;
/** Offset 0x06C5 - Skip external display device scanning
Enable: Do not scan for external display device, Disable (Default): Scan external
display devices
$EN_DIS
**/
UINT8 SkipExtGfxScan;
/** Offset 0x06C6 - Generate BIOS Data ACPI Table
Enable: Generate BDAT for MRC RMT or SA PCIe data. Disable (Default): Do not generate it
$EN_DIS
**/
UINT8 BdatEnable;
/** Offset 0x06C7 - Detect External Graphics device for LegacyOpROM
Detect and report if external graphics device only support LegacyOpROM or not (to
support CSM auto-enable). Enable(Default)=1, Disable=0
$EN_DIS
**/
UINT8 ScanExtGfxForLegacyOpRom;
/** Offset 0x06C8 - Lock PCU Thermal Management registers
Lock PCU Thermal Management registers. Enable(Default)=1, Disable=0
$EN_DIS
**/
UINT8 LockPTMregs;
/** Offset 0x06C9 - Rsvd
Disable(0x0)(Default): Normal Operation - RxCTLE adaptive behavior enabled, Enable(0x1):
Override RxCTLE - Disable RxCTLE adaptive behavior to keep the configured RxCTLE
peak values unmodified
$EN_DIS
**/
UINT8 PegGen3Rsvd;
/** Offset 0x06CA - Panel Power Enable
Control for enabling/disabling VDD force bit (Required only for early enabling of
eDP panel). 0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 PanelPowerEnable;
/** Offset 0x06CB - BdatTestType
Indicates the type of Memory Training data to populate into the BDAT ACPI table.
0:RMT per Rank, 1:RMT per Bit, 2:Margin2D
**/
UINT8 BdatTestType;
/** Offset 0x06CC - PMR Size
Size of PMR memory buffer. 0x400000 for normal boot and 0x200000 for S3 boot
**/
UINT32 DmaBufferSize;
/** Offset 0x06D0 - VT-d/IOMMU Boot Policy
BIT0: Enable IOMMU during boot, BIT1: Enable IOMMU when transfer control to OS
**/
UINT8 PreBootDmaMask;
/** Offset 0x06D1 - Enable/Disable DMI GEN3 Hardware Eq
Enable/Disable DMI GEN3 Hardware Eq. Disabled(0x0): Disable Hardware Eq, Enabled(0x1)(Default):
Enable EQ Phase1 Static Presets Programming
$EN_DIS
**/
UINT8 DmiHweq;
/** Offset 0x06D2 - Enable/Disable CPU DMI GEN3 Phase 23 Bypass
CPU DMI GEN3 Phase 23 Bypass. Disabled(0x0)(Default): Disable Phase 23 Bypass, Enabled(0x1):
Enable Phase 23 Bypass
$EN_DIS
**/
UINT8 Gen3EqPhase23Bypass;
/** Offset 0x06D3 - Enable/Disable CPU DMI GEN3 Phase 3 Bypass
CPU DMI GEN3 Phase 3 Bypass. Disabled(0x0)(Default): Disable Phase 3 Bypass, Enabled(0x1):
Enable Phase 3 Bypass
$EN_DIS
**/
UINT8 Gen3EqPhase3Bypass;
/** Offset 0x06D4 - Enable/Disable CPU DMI Gen3 EQ Local Transmitter Coefficient Override Enable
Program Gen3 EQ Local Transmitter Coefficient Override. Disabled(0x0)(Default):
Disable Local Transmitter Coefficient Override, Enabled(0x1): Enable Local Transmitter
Coefficient Override
$EN_DIS
**/
UINT8 Gen3LtcoEnable;
/** Offset 0x06D5 - Enable/Disable CPU DMI Gen3 EQ Remote Transmitter Coefficient/Preset Override Enable
Program Remote Transmitter Coefficient/Preset Override. Disabled(0x0): Disable Remote
Transmitter Coefficient/Preset Override, Enabled(0x1)(Default): Enable Remote
Transmitter Coefficient/Preset Override
$EN_DIS
**/
UINT8 Gen3RtcoRtpoEnable;
/** Offset 0x06D6 - DMI Gen3 Transmitter Pre-Cursor Coefficient
Used for programming DMI Gen3 Transmitter Pre-Cursor Coefficient . Range: 0-10,
2 is default for each lane
**/
UINT8 DmiGen3Ltcpre[8];
/** Offset 0x06DE - DMI Gen3 Transmitter Post-Cursor Coefficient
Used for programming Transmitter Post-Cursor Coefficient. Range: 0-9, 2 is default
for each lane
**/
UINT8 DmiGen3Ltcpo[8];
/** Offset 0x06E6 - PCIE Hw Eq Gen3 CoeffList Cm
CPU_PCIE_EQ_PARAM. Coefficient C-1.
**/
UINT8 CpuDmiHwEqGen3CoeffListCm[8];
/** Offset 0x06EE - PCIE Hw Eq Gen3 CoeffList Cp
CPU_PCIE_EQ_PARAM. Coefficient C+1.
**/
UINT8 CpuDmiHwEqGen3CoeffListCp[8];
/** Offset 0x06F6 - Enable/Disable DMI GEN3 DmiGen3DsPresetEnable
Enable/Disable DMI GEN3 DmiGen3DsPreset. Auto(0x0)(Default): DmiGen3DsPresetEnable,
Manual(0x1): Enable DmiGen3DsPresetEnable
$EN_DIS
**/
UINT8 DmiGen3DsPresetEnable;
/** Offset 0x06F7 - DMI Gen3 Root port preset Rx values per lane
Used for programming DMI Gen3 preset values per lane. Range: 0-10, 1 is default
for each lane
**/
UINT8 DmiGen3DsPortRxPreset[8];
/** Offset 0x06FF - DMI Gen3 Root port preset Tx values per lane
Used for programming DMI Gen3 preset values per lane. Range: 0-10, 7 is default
for each lane
**/
UINT8 DmiGen3DsPortTxPreset[8];
/** Offset 0x0707 - Program DMI GEN3 Extended number of VC
(DEPRECATED)
**/
UINT8 DmiGen3MultiVC;
/** Offset 0x0708 - Enable/Disable DMI GEN3 DmiGen3Vc1Control
(DEPRECATED)
$EN_DIS
**/
UINT8 DmiGen3Vc1Control;
/** Offset 0x0709 - Enable/Disable DMI GEN3 DmiGen3VcMControl
(DEPRECATED)
$EN_DIS
**/
UINT8 DmiGen3VcMControl;
/** Offset 0x070A - DMI Secure Register Lock:{Combo
(DEPRECATED)
0:Disable, 1:Enable
**/
UINT8 DmiSrl;
/** Offset 0x070B - DMI Scramble Enable:{Combo
(DEPRECATED)
0:Disable, 1:Enable
**/
UINT8 DmiScramble;
/** Offset 0x070C - DMI Max Payload Size:{Combo
(DEPRECATED)
0:Auto, 1:128 TLP, 2:256 TLP
**/
UINT8 DmiMaxPayload;
/** Offset 0x070D - DPin Dynamic Switch Policy
Dynamic one-time switch from iGFx to dGFx after boot to OS
0: Disble, 1: Enable
**/
UINT8 DPinDynamicSwitch;
/** Offset 0x070E - Delay before sending commn
Delay before sending dynamic one-time switch cmd to IOM, ACPI BIOS consumes this
value and proceed delay when _DSM is invoked: 0=Minimal, 5000=Maximum, default
is 0 second
**/
UINT16 DPinDynamicSwitchDelay0;
/** Offset 0x0710 - Delay before IOM de-assert HPD
Delay before IOM de-assert HPD, ACPI BIOS passes this value to IOM when sending
dynamic one-time switch command: 1000=Minimal, 5000=Maximum, default is 1000 = 1 second
**/
UINT16 DPinDynamicSwitchDelay1;
/** Offset 0x0712 - SaPreMemTestRsvd
Reserved for SA Pre-Mem Test
$EN_DIS
**/
UINT8 SaPreMemTestRsvd[28];
/** Offset 0x072E - TotalFlashSize
Enable/Disable. 0: Disable, define default value of TotalFlashSize , 1: enable
**/
UINT16 TotalFlashSize;
/** Offset 0x0730 - BiosSize
The size of the BIOS region of the IFWI. Used if FspmUpd->FspmConfig.BiosGuard !=
0. If BiosGuard is enabled, MRC will increase the size of the DPR (DMA Protected
Range) so that a BIOS Update Script can be stored in the DPR.
**/
UINT16 BiosSize;
/** Offset 0x0732 - SecurityTestRsvd
Reserved for SA Pre-Mem Test
$EN_DIS
**/
UINT8 SecurityTestRsvd[12];
/** Offset 0x073E - Smbus dynamic power gating
Disable or Enable Smbus dynamic power gating.
$EN_DIS
**/
UINT8 SmbusDynamicPowerGating;
/** Offset 0x073F - Disable and Lock Watch Dog Register
Set 1 to clear WDT status, then disable and lock WDT registers.
$EN_DIS
**/
UINT8 WdtDisableAndLock;
/** Offset 0x0740 - SMBUS SPD Write Disable
Set/Clear Smbus SPD Write Disable. 0: leave SPD Write Disable bit; 1: set SPD Write
Disable bit. For security recommendations, SPD write disable bit must be set.
$EN_DIS
**/
UINT8 SmbusSpdWriteDisable;
/** Offset 0x0741 - VC Type
Virtual Channel Type Select: 0: VC0, 1: VC1.
0: VC0, 1: VC1
**/
UINT8 PchHdaVcType;
/** Offset 0x0742 - Universal Audio Architecture compliance for DSP enabled system
0: Not-UAA Compliant (Intel SST driver supported only), 1: UAA Compliant (HDA Inbox
driver or SST driver supported).
$EN_DIS
**/
UINT8 PchHdaDspUaaCompliance;
/** Offset 0x0743 - Enable HD Audio Link
Enable/disable HD Audio Link. Muxed with SSP0/SSP1/SNDW1.
$EN_DIS
**/
UINT8 PchHdaAudioLinkHdaEnable;
/** Offset 0x0744 - Enable HDA SDI lanes
Enable/disable HDA SDI lanes.
**/
UINT8 PchHdaSdiEnable[2];
/** Offset 0x0746 - HDA Power/Clock Gating (PGD/CGD)
Enable/Disable HD Audio Power and Clock Gating(POR: Enable). 0: PLATFORM_POR, 1:
FORCE_ENABLE, 2: FORCE_DISABLE.
0: POR, 1: Force Enable, 2: Force Disable
**/
UINT8 PchHdaTestPowerClockGating;
/** Offset 0x0747 - Enable HD Audio DMIC_N Link
Enable/disable HD Audio DMIC1 link. Muxed with SNDW3.
**/
UINT8 PchHdaAudioLinkDmicEnable[2];
/** Offset 0x0749
**/
UINT8 UnusedUpdSpace20[3];
/** Offset 0x074C - DMIC<N> ClkA Pin Muxing (N - DMIC number)
Determines DMIC<N> ClkA Pin muxing. See GPIO_*_MUXING_DMIC<N>_CLKA_*
**/
UINT32 PchHdaAudioLinkDmicClkAPinMux[2];
/** Offset 0x0754 - DMIC<N> ClkB Pin Muxing
Determines DMIC<N> ClkA Pin muxing. See GPIO_*_MUXING_DMIC<N>_CLKB_*
**/
UINT32 PchHdaAudioLinkDmicClkBPinMux[2];
/** Offset 0x075C - Enable HD Audio DSP
Enable/disable HD Audio DSP feature.
$EN_DIS
**/
UINT8 PchHdaDspEnable;
/** Offset 0x075D
**/
UINT8 UnusedUpdSpace21[3];
/** Offset 0x0760 - DMIC<N> Data Pin Muxing
Determines DMIC<N> Data Pin muxing. See GPIO_*_MUXING_DMIC<N>_DATA_*
**/
UINT32 PchHdaAudioLinkDmicDataPinMux[2];
/** Offset 0x0768 - Enable HD Audio SSP0 Link
Enable/disable HD Audio SSP_N/I2S link. Muxed with HDA. N-number 0-5
**/
UINT8 PchHdaAudioLinkSspEnable[6];
/** Offset 0x076E - Enable HD Audio SoundWire#N Link
Enable/disable HD Audio SNDW#N link. Muxed with HDA.
**/
UINT8 PchHdaAudioLinkSndwEnable[4];
/** Offset 0x0772 - iDisp-Link Frequency
iDisp-Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 4: 96MHz, 3: 48MHz.
4: 96MHz, 3: 48MHz
**/
UINT8 PchHdaIDispLinkFrequency;
/** Offset 0x0773 - iDisp-Link T-mode
iDisp-Link T-Mode (PCH_HDAUDIO_IDISP_TMODE enum): 0: 2T, 2: 4T, 3: 8T(Default), 4: 16T
0: 2T, 2: 4T, 3: 8T, 4: 16T
**/
UINT8 PchHdaIDispLinkTmode;
/** Offset 0x0774 - iDisplay Audio Codec disconnection
0: Not disconnected, enumerable, 1: Disconnected SDI, not enumerable.
$EN_DIS
**/
UINT8 PchHdaIDispCodecDisconnect;
/** Offset 0x0775 - Force ME DID Init Status
Test, 0: disable, 1: Success, 2: No Memory in Channels, 3: Memory Init Error, Set
ME DID init stat value
$EN_DIS
**/
UINT8 DidInitStat;
/** Offset 0x0776 - CPU Replaced Polling Disable
Test, 0: disable, 1: enable, Setting this option disables CPU replacement polling loop
$EN_DIS
**/
UINT8 DisableCpuReplacedPolling;
/** Offset 0x0777 - ME DID Message
(DEPRECATED)Test, 0: disable, 1: enable, Enable/Disable ME DID Message (disable
will prevent the DID message from being sent)
$EN_DIS
**/
UINT8 SendDidMsg;
/** Offset 0x0778 - Check HECI message before send
Test, 0: disable, 1: enable, Enable/Disable message check.
$EN_DIS
**/
UINT8 DisableMessageCheck;
/** Offset 0x0779 - Skip MBP HOB
Test, 0: disable, 1: enable, Enable/Disable MOB HOB.
$EN_DIS
**/
UINT8 SkipMbpHob;
/** Offset 0x077A - HECI2 Interface Communication
Test, 0: disable, 1: enable, Adds or Removes HECI2 Device from PCI space.
$EN_DIS
**/
UINT8 HeciCommunication2;
/** Offset 0x077B - Enable KT device
Test, 0: disable, 1: enable, Enable or Disable KT device.
$EN_DIS
**/
UINT8 KtDeviceEnable;
/** Offset 0x077C - Hybrid Graphics GPIO information for PEG 1
Hybrid Graphics GPIO information for PEG 1, for Reset, power and wake GPIOs
**/
UINT32 CpuPcie1Rtd3Gpio[24];
/** Offset 0x07DC - Hybrid Graphics GPIO information for PEG 2
Hybrid Graphics GPIO information for PEG 2, for Reset, power and wake GPIOs
**/
UINT32 CpuPcie2Rtd3Gpio[24];
/** Offset 0x083C - Hybrid Graphics GPIO information for PEG 3
Hybrid Graphics GPIO information for PEG 3, for Reset, power and wake GPIOs
**/
UINT32 CpuPcie3Rtd3Gpio[24];
/** Offset 0x089C - Skip CPU replacement check
Test, 0: disable, 1: enable, Setting this option to skip CPU replacement check
$EN_DIS
**/
UINT8 SkipCpuReplacementCheck;
/** Offset 0x089D - PCI Express Dekel Workaround
Select the 1 to 9 for Dekel registers endpoint programming: 1=Minimal, 9=Maximum,
default is 2
**/
UINT8 CpuPcieRpDekelSquelchWa;
/** Offset 0x089E - Serial Io Uart Debug Mode
Select SerialIo Uart Controller mode
0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
4:SerialIoUartSkipInit
**/
UINT8 SerialIoUartDebugMode;
/** Offset 0x089F
**/
UINT8 UnusedUpdSpace22;
/** Offset 0x08A0 - SerialIoUartDebugRxPinMux - FSPT
Select RX pin muxing for SerialIo UART used for debug
**/
UINT32 SerialIoUartDebugRxPinMux;
/** Offset 0x08A4 - SerialIoUartDebugTxPinMux - FSPM
Select TX pin muxing for SerialIo UART used for debug
**/
UINT32 SerialIoUartDebugTxPinMux;
/** Offset 0x08A8 - SerialIoUartDebugRtsPinMux - FSPM
Select SerialIo Uart used for debug Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
for possible values.
**/
UINT32 SerialIoUartDebugRtsPinMux;
/** Offset 0x08AC - SerialIoUartDebugCtsPinMux - FSPM
Select SerialIo Uart used for debug Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
for possible values.
**/
UINT32 SerialIoUartDebugCtsPinMux;
/** Offset 0x08B0 - Avx2 Voltage Guardband Scaling Factor
AVX2 Voltage Guardband Scale factor applied to AVX2 workloads. Range is 0-200 in
1/100 units, where a value of 125 would apply a 1.25 scale factor.
**/
UINT8 Avx2VoltageScaleFactor;
/** Offset 0x08B1 - Avx512 Voltage Guardband Scaling Factor
AVX512 Voltage Guardband Scale factor applied to AVX512 workloads. Range is 0-200
in 1/100 units, where a value of 125 would apply a 1.25 scale factor.
**/
UINT8 Avx512VoltageScaleFactor;
/** Offset 0x08B2 - Lane Used of CSI port
Lane Used of each CSI port
1:x1, 2:x2, 3:x3, 4:x4, 8:x8
**/
UINT8 IpuLaneUsed[8];
/** Offset 0x08BA - Lane Used of CSI port
Speed of each CSI port
0:Sensor default, 1:<416Mbps, 2:<1.5Gbps, 3:<2Gbps, 4:<2.5Gbps, 5:<4Gbps, 6:>4Gbps
**/
UINT8 CsiSpeed[8];
/** Offset 0x08C2 - DPmem Support
1: enable, 0: disable(Default), Enable/disable setting for Dynamic Persistent Memory support
$EN_DIS
**/
UINT8 DpmemSupport;
/** Offset 0x08C3 - Core VF Point Offset Mode
Selects Core Voltage & Frequency Point Offset between Legacy and Selection modes;
<b>0: Legacy</b>; 1: Selection.
0:Legacy, 1:Selection
**/
UINT8 CoreVfPointOffsetMode;
/** Offset 0x08C4 - Core VF Point Offset
Array used to specifies the Offset Voltage applied to the each selected Core VF
Point. This voltage is specified in millivolts.
**/
UINT16 CoreVfPointOffset[15];
/** Offset 0x08E2 - Core VF Point Offset Prefix
Sets the CoreVfPointOffset value as positive or negative for corresponding core
VF Point; <b>0: Positive </b>; 1: Negative.
0:Positive, 1:Negative
**/
UINT8 CoreVfPointOffsetPrefix[15];
/** Offset 0x08F1 - Core VF Point Ratio
Array for the each selected Core VF Point to display the ration.
**/
UINT8 CoreVfPointRatio[15];
/** Offset 0x0900 - Core VF Point Count
Number of supported Core Voltage & Frequency Point Offset
**/
UINT8 CoreVfPointCount;
/** Offset 0x0901 - Enable CPU CrashLog GPRs dump
Enable or Disable CPU CrashLog GPRs dump; <b>0: Disable</b>; 1: Enable; 2: Only
disable Smm GPRs dump
0:Disabled, 1:Enabled, 2:Only Smm GPRs Disabled
**/
UINT8 CrashLogGprs;
/** Offset 0x0902
**/
UINT8 UnusedUpdSpace23[2];
/** Offset 0x0904 - Bitmask of disable cores
Core mask is a bitwise indication of which core should be disabled. <b>0x00=Default</b>;
Bit 0 - core 0, bit 7 - core 7.
**/
UINT32 DisableCoreMask;
/** Offset 0x0908 - REFRESH_PANIC_WM
<b>@deprecated</b> - Not used and has no effect, Please use RefreshWm
**/
UINT8 RefreshPanicWm;
/** Offset 0x0909 - REFRESH_HP_WM
<b>@deprecated</b> - Not used and has no effect, Please use RefreshWm
**/
UINT8 RefreshHpWm;
/** Offset 0x090A - Support Unlimited ICCMAX
Support Unlimited ICCMAX more than maximum value 255.75A; <b>0: Disabled</b>; 1: Enabled.
$EN_DIS
**/
UINT8 UnlimitedIccMax;
/** Offset 0x090B - Per Core Max Ratio override
Enable or disable Per Core PState OC supported by writing OCMB 0x1D to program new
favored core ratio to each Core. <b>0: Disable</b>, 1: enable
$EN_DIS
**/
UINT8 PerCoreRatioOverride;
/** Offset 0x090C - Per Core Current Max Ratio
Array for the Per Core Max Ratio
**/
UINT8 PerCoreRatio[10];
/** Offset 0x0916 - Margin Limit Check
Margin Limit Check. Choose level of margin check
0:Disable, 1:L1, 2:L2, 3:Both
**/
UINT8 MarginLimitCheck;
/** Offset 0x0917
**/
UINT8 UnusedUpdSpace24;
/** Offset 0x0918 - Margin Limit L2
% of L1 check for margin limit check
**/
UINT16 MarginLimitL2;
/** Offset 0x091A - Iotg Pll SscEn
Enable or disable CPU SSC. 0: Disable, <b>1: Enable</b>
$EN_DIS
**/
UINT8 IotgPllSscEn;
/** Offset 0x091B - GPIO Override
Gpio Override Level - FSP will not configure any GPIOs and rely on GPIO setings
before moved to FSP. Available configurations 0: Disable;1: Level 1 - skips GpioSetNativePadByFunction;Level
2 - skips GpioSetNativePadByFunction and GpioSetPadMode
**/
UINT8 GpioOverride;
/** Offset 0x091C - Write0 enabling
Enable/Disable Write0
$EN_DIS
**/
UINT8 WRITE0;
/** Offset 0x091D
**/
UINT8 UnusedUpdSpace25[3];
/** Offset 0x0920
**/
UINT32 VccInVoltageOverride;
/** Offset 0x0924 - Dynamic Memory Timings Changes
Dynamic Memory Timings Changes; <b>0: Disabled</b>; 1: Enabled.
$EN_DIS
**/
UINT8 DynamicMemoryChange;
/** Offset 0x0925 - IbeccErrorInj
In-Band ECC Error Injection NOTE: For Debug or Development purposes only! Disable
this option for production systems.
$EN_DIS
**/
UINT8 IbeccErrorInj;
/** Offset 0x0926 - Enable/Disable DMI GEN3 DmiGen3UsPresetEnable
Enable/Disable DMI GEN3 DmiGen3UsPreset. Auto(0x0)(Default): DmiGen3UsPresetEnable,
Manual(0x1): Enable DmiGen3UsPresetEnable
$EN_DIS
**/
UINT8 DmiGen3UsPresetEnable;
/** Offset 0x0927 - DMI Gen3 Root port preset Rx values per lane
Used for programming DMI Gen3 preset values per lane. Range: 0-10, 7 is default
for each lane
**/
UINT8 DmiGen3UsPortRxPreset[8];
/** Offset 0x092F - DMI Gen3 Root port preset Tx values per lane
Used for programming DMI Gen3 preset values per lane. Range: 0-10, 1 is default
for each lane
**/
UINT8 DmiGen3UsPortTxPreset[8];
/** Offset 0x0937 - BCLK Frequency Source
Clock source of BCLK OC frequency, <b>0:CPU BCLK</b>, 1:PCH BCLK, 2:External CLK
0:CPU BCLK, 1:PCH BCLK, 2:External CLK
**/
UINT8 BclkSource;
/** Offset 0x0938 - CPU BCLK OC Frequency
CPU BCLK OC Frequency in 10KHz units increasing. Value 9800 (10KHz) = 98MHz <b>0
- Auto</b>. Range is 8000-50000 (10KHz).
**/
UINT32 CpuBclkOcFrequency;
/** Offset 0x093C - Ring CCF Auto Gv Disable Down
Ring CCF Auto Gv Disable Down, 0: Disabled, <b>1:Fused default</b>
0:Disabled, 1:Fused default
**/
UINT8 RingCcfAutoGvDisable;
/** Offset 0x093D - SA/Uncore voltage mode
SA/Uncore voltage mode; <b>0: Adaptive</b>; 1: Override.
$EN_DIS
**/
UINT8 SaVoltageMode;
/** Offset 0x093E - SA/Uncore Voltage Override
The SA/Uncore voltage override applicable when SA/Uncore voltage mode is in Override
mode. Valid Range 0 to 2000
**/
UINT16 SaVoltageOverride;
/** Offset 0x0940 - SA/Uncore Extra Turbo voltage
Extra Turbo voltage applicable when SA/Uncore voltage mode is in Adaptive mode.
Valid Range 0 to 2000
**/
UINT16 SaExtraTurboVoltage;
/** Offset 0x0942 - DdrMemoryDown
DDR Memory Down Support.
$EN_DIS
**/
UINT8 DdrMemoryDown;
/** Offset 0x0943
**/
UINT8 UnusedUpdSpace26;
/** Offset 0x0944 - The VccIn Max Voltage Limit
This will override maximum VCCIN voltage limit to the voltage value specified. <b>0
- no override</b> Valid Range 0 to 3000mV
**/
UINT16 VccInMaxLimit;
/** Offset 0x0946 - VccIO Voltage Override
This will override VccIO output voltage level to the voltage value specified. Valid
Range 0 to 2000
**/
UINT16 VccIoVoltageOverride;
/** Offset 0x0948 - Boost VRef Voltage
<b> Default: 0: 0.7V </b> 1: 1.0V to support the high frequencies needed for BCLK OC.
0: 0.7V , 1:1.0V
**/
UINT8 BoostRefVoltage;
/** Offset 0x0949 - Pcie Ref Pll SSC
Pcie Ref Pll SSC Percentatge. 0x0: 0.0%, 0x1: 0.1%, 0x2:0.2%, 0x3: 0.3%, 0x4: 0.4%,
0x5: 0.5%, 0xFE: Disable, 0xFF: Auto
**/
UINT8 PcieRefPllSsc;
/** Offset 0x094A - Refresh Watermarks
Refresh Watermark, High, Low
1:Enable Refresh Watermark High (Default), 0:Enable Refresh Watermark Low
**/
UINT8 RefreshWm;
/** Offset 0x094B
**/
UINT8 UnusedUpdSpace27[4];
/** Offset 0x094F
**/
UINT8 ReservedFspmUpd2[1];
} FSP_M_CONFIG;
/** Fsp M UPD Configuration
**/
typedef struct {
/** Offset 0x0000
**/
FSP_UPD_HEADER FspUpdHeader;
/** Offset 0x0020
**/
FSPM_ARCH_UPD FspmArchUpd;
/** Offset 0x0040
**/
FSP_M_CONFIG FspmConfig;
/** Offset 0x0950
**/
UINT8 UnusedUpdSpace28[6];
/** Offset 0x0956
**/
UINT16 UpdTerminator;
} FSPM_UPD;
#pragma pack()
#endif