config SOC_INTEL_CANNONLAKE_BASE
	bool
	select ACPI_INTEL_HARDWARE_SLEEP_VALUES
	select ACPI_NHLT
	select ARCH_X86
	select BOOT_DEVICE_SUPPORTS_WRITES
	select CACHE_MRC_SETTINGS
	select CPU_INTEL_COMMON
	select CPU_INTEL_FIRMWARE_INTERFACE_TABLE
	select CPU_SUPPORTS_PM_TIMER_EMULATION
	select DISPLAY_FSP_VERSION_INFO
	select EDK2_CPU_TIMER_LIB if PAYLOAD_EDK2
	select FSP_COMPRESS_FSP_S_LZMA
	select FSP_M_XIP
	select FSP_STATUS_GLOBAL_RESET_REQUIRED_3
	select FSP_USES_CB_STACK
	select GENERIC_GPIO_LIB
	select HAVE_DPTF_EISA_HID
	select HAVE_FSP_GOP
	select HAVE_FSP_LOGO_SUPPORT
	select HAVE_HYPERTHREADING
	select HAVE_INTEL_FSP_REPO
	select HAVE_SMI_HANDLER
	select IDT_IN_EVERY_STAGE
	select INTEL_DESCRIPTOR_MODE_CAPABLE
	select INTEL_GMA_ACPI
	select INTEL_GMA_ADD_VBT if RUN_FSP_GOP
	select MRC_SETTINGS_PROTECT
	select PARALLEL_MP_AP_WORK
	select PLATFORM_USES_FSP2_0
	select PMC_GLOBAL_RESET_ENABLE_LOCK
	select SOC_INTEL_COMMON
	select SOC_INTEL_COMMON_ACPI_WAKE_SOURCE
	select SOC_INTEL_COMMON_BLOCK
	select SOC_INTEL_COMMON_BLOCK_ACPI
	select SOC_INTEL_COMMON_BLOCK_ACPI_CPPC
	select SOC_INTEL_COMMON_BLOCK_ACPI_GPIO
	select SOC_INTEL_COMMON_BLOCK_ACPI_LPIT
	select SOC_INTEL_COMMON_BLOCK_ACPI_PEP
	select SOC_INTEL_COMMON_BLOCK_CAR
	select SOC_INTEL_COMMON_BLOCK_CHIP_CONFIG
	select SOC_INTEL_COMMON_BLOCK_CNVI
	select SOC_INTEL_COMMON_BLOCK_CPU
	select SOC_INTEL_COMMON_BLOCK_CPU_MPINIT
	select SOC_INTEL_COMMON_BLOCK_CPU_SMMRELOCATE
	select SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT
	select SOC_INTEL_COMMON_BLOCK_GSPI_VERSION_2
	select SOC_INTEL_COMMON_BLOCK_HDA
	select SOC_INTEL_COMMON_BLOCK_IRQ
	select SOC_INTEL_COMMON_BLOCK_ME_SPEC_12
	select SOC_INTEL_COMMON_BLOCK_POWER_LIMIT
	select SOC_INTEL_COMMON_BLOCK_SA
	select SOC_INTEL_COMMON_BLOCK_SCS
	select SOC_INTEL_COMMON_BLOCK_SMM
	select SOC_INTEL_COMMON_BLOCK_SMM_IO_TRAP
	select SOC_INTEL_COMMON_BLOCK_THERMAL_PCI_DEV
	select SOC_INTEL_COMMON_BLOCK_XHCI
	select SOC_INTEL_COMMON_BLOCK_XHCI_ELOG
	select SOC_INTEL_COMMON_FSP_RESET
	select SOC_INTEL_COMMON_NHLT
	select SOC_INTEL_COMMON_PCH_CLIENT
	select SOC_INTEL_COMMON_RESET
	select SOC_INTEL_CONFIGURE_DDI_A_4_LANES
	select SOC_INTEL_MEM_MAPPED_PM_CONFIGURATION
	select SSE2
	select SUPPORT_CPU_UCODE_IN_CBFS
	select TSC_MONOTONIC_TIMER
	select UDELAY_TSC
	select UDK_2017_BINDING
	select USE_FSP_NOTIFY_PHASE_POST_PCI_ENUM
	select USE_FSP_NOTIFY_PHASE_READY_TO_BOOT
	select USE_FSP_NOTIFY_PHASE_END_OF_FIRMWARE
	select X86_CLFLUSH_CAR

config SOC_INTEL_COFFEELAKE
	bool
	select SOC_INTEL_CANNONLAKE_BASE
	select HAVE_EXP_X86_64_SUPPORT
	select HECI_DISABLE_USING_SMM
	select INTEL_CAR_NEM

config SOC_INTEL_WHISKEYLAKE
	bool
	select SOC_INTEL_CANNONLAKE_BASE
	select HECI_DISABLE_USING_SMM
	select INTEL_CAR_NEM_ENHANCED

config SOC_INTEL_COMETLAKE
	bool
	select SOC_INTEL_CANNONLAKE_BASE
	select INTEL_CAR_NEM_ENHANCED
	select PMC_IPC_ACPI_INTERFACE if DISABLE_HECI1_AT_PRE_BOOT
	select SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_PMC_IPC
	select SOC_INTEL_COMMON_BASECODE
	select SOC_INTEL_COMMON_BASECODE_RAMTOP

config SOC_INTEL_COMETLAKE_1
	bool
	select SOC_INTEL_COMETLAKE

config SOC_INTEL_COMETLAKE_2
	bool
	select SOC_INTEL_COMETLAKE

config SOC_INTEL_COMETLAKE_1_2
	bool
	select SOC_INTEL_COMETLAKE
	select PLATFORM_USES_SECOND_FSP
	help
	  Support both CML v1 and v2, for boards that may have either stepping.
	  Embeds both FSPs and selects the correct one at runtime.  The second
	  FSP consumes about 800 KiB of flash space.

	  The first FSP is for CML v1, the second is for CML v2.

config SOC_INTEL_COMETLAKE_S
	bool
	select SOC_INTEL_COMETLAKE

config SOC_INTEL_COMETLAKE_V
	bool
	select SOC_INTEL_COMETLAKE

config SOC_INTEL_CANNONLAKE_PCH_H
	bool

if SOC_INTEL_CANNONLAKE_BASE

config MAX_CPUS
	int
	default 20 if SOC_INTEL_CANNONLAKE_PCH_H && SOC_INTEL_COMETLAKE
	default 16 if SOC_INTEL_CANNONLAKE_PCH_H && SOC_INTEL_COFFEELAKE
	default 12 if !SOC_INTEL_CANNONLAKE_PCH_H && SOC_INTEL_COMETLAKE
	default 8

config DIMM_SPD_SIZE
	default 512

config DCACHE_RAM_BASE
	default 0xfef00000

config DCACHE_RAM_SIZE
	default 0x40000
	help
	  The size of the cache-as-ram region required during bootblock
	  and/or romstage.

config DCACHE_BSP_STACK_SIZE
	hex
	default 0x20400 if FSP_USES_CB_STACK
	default 0x4000
	help
	  The amount of anticipated stack usage in CAR by bootblock and
	  other stages. In the case of FSP_USES_CB_STACK default value will be
	  sum of FSP-M stack requirement (128KiB) and CB romstage stack requirement (~1KiB).

config FSP_TEMP_RAM_SIZE
	hex
	depends on FSP_USES_CB_STACK
	default 0x10000
	help
	  The amount of anticipated heap usage in CAR by FSP.
	  Refer to Platform FSP integration guide document to know
	  the exact FSP requirement for Heap setup.

config IFD_CHIPSET
	string
	default "cnl"

config IED_REGION_SIZE
	hex
	default 0x400000

config NHLT_DMIC_1CH_16B
	bool
	depends on ACPI_NHLT
	default n
	help
	  Include DSP firmware settings for 1 channel 16B DMIC array.

config NHLT_DMIC_2CH_16B
	bool
	depends on ACPI_NHLT
	default n
	help
	  Include DSP firmware settings for 2 channel 16B DMIC array.

config NHLT_DMIC_4CH_16B
	bool
	depends on ACPI_NHLT
	default n
	help
	  Include DSP firmware settings for 4 channel 16B DMIC array.

config NHLT_MAX98357
	bool
	depends on ACPI_NHLT
	default n
	help
	  Include DSP firmware settings for headset codec.

config NHLT_MAX98373
	bool
	depends on ACPI_NHLT
	default n
	help
	  Include DSP firmware settings for headset codec.

config NHLT_DA7219
	bool
	depends on ACPI_NHLT
	default n
	help
	  Include DSP firmware settings for headset codec.

config MAX_ROOT_PORTS
	int
	default 24 if SOC_INTEL_CANNONLAKE_PCH_H
	default 16

config MAX_PCIE_CLOCK_SRC
	int
	default 16 if SOC_INTEL_CANNONLAKE_PCH_H
	default 6

config SMM_TSEG_SIZE
	hex
	default 0x800000

config SMM_RESERVED_SIZE
	hex
	default 0x200000

config PCR_BASE_ADDRESS
	hex
	default 0xfd000000
	help
	  This option allows you to select MMIO Base Address of sideband bus.

config CPU_BCLK_MHZ
	int
	default 100

config SOC_INTEL_COMMON_BLOCK_GSPI_CLOCK_MHZ
	int
	default 120

config CPU_XTAL_HZ
	default 24000000

config DRIVERS_I2C_DESIGNWARE_CLOCK_MHZ
	int
	default 216

config SOC_INTEL_COMMON_BLOCK_GSPI_MAX
	int
	default 3

config SOC_INTEL_I2C_DEV_MAX
	int
	default 4 if SOC_INTEL_CANNONLAKE_PCH_H
	default 6

config CONSOLE_UART_BASE_ADDRESS
	hex
	default 0xfe032000
	depends on INTEL_LPSS_UART_FOR_CONSOLE

# Clock divider parameters for 115200 baud rate
config SOC_INTEL_COMMON_LPSS_UART_CLK_M_VAL
	hex
	default 0x30

config SOC_INTEL_COMMON_LPSS_UART_CLK_N_VAL
	hex
	default 0xc35

config VBOOT
	select VBOOT_MUST_REQUEST_DISPLAY
	select VBOOT_STARTS_IN_BOOTBLOCK
	select VBOOT_VBNV_CMOS
	select VBOOT_VBNV_CMOS_BACKUP_TO_FLASH

config CBFS_SIZE
	default 0x200000

config MB_HAS_ACTIVE_HIGH_SD_PWR_ENABLE
	bool
	default n
	help
	  Select this if the board has a SD_PWR_ENABLE pin connected to a
	  active high sensing load switch to turn on power to the card reader.
	  This will enable a workaround in ASL _PS3 and _PS0 methods to force
	  SD_PWR_ENABLE to stay low in D3.

config FSP_HEADER_PATH
	default "3rdparty/fsp/CoffeeLakeFspBinPkg/Include/" if SOC_INTEL_COFFEELAKE || SOC_INTEL_WHISKEYLAKE
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLake1/Include/" if SOC_INTEL_COMETLAKE_1
	# CML v1/v2 headers are equivalent (differ only in comments) so build
	# against v2 arbitrarily.
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLake2/Include/" if SOC_INTEL_COMETLAKE_2 || SOC_INTEL_COMETLAKE_1_2
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLakeS/Include/" if SOC_INTEL_COMETLAKE_S
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLakeV/Include/" if SOC_INTEL_COMETLAKE_V

config FSP_FD_PATH
	default "3rdparty/fsp/CoffeeLakeFspBinPkg/Fsp.fd" if SOC_INTEL_COFFEELAKE || SOC_INTEL_WHISKEYLAKE
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLake1/Fsp.fd" if SOC_INTEL_COMETLAKE_1 || SOC_INTEL_COMETLAKE_1_2
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLake2/Fsp.fd" if SOC_INTEL_COMETLAKE_2
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLakeS/Fsp.fd" if SOC_INTEL_COMETLAKE_S
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLakeV/Fsp.fd" if SOC_INTEL_COMETLAKE_V

config FSP_FD_PATH_2
	default "3rdparty/fsp/CometLakeFspBinPkg/CometLake2/Fsp.fd" if SOC_INTEL_COMETLAKE_1_2

config SOC_INTEL_CANNONLAKE_DEBUG_CONSENT
	int "Debug Consent for CNL"
	# USB DBC is more common for developers so make this default to 3 if
	# SOC_INTEL_DEBUG_CONSENT=y
	default 3 if SOC_INTEL_DEBUG_CONSENT
	default 0
	help
	  This is to control debug interface on SOC.
	  Setting non-zero value will allow to use DBC or DCI to debug SOC.
	  PlatformDebugConsent in FspmUpd.h has the details.

config PRERAM_CBMEM_CONSOLE_SIZE
	hex
	default 0xe00

config INTEL_TXT_BIOSACM_ALIGNMENT
	hex
	default 0x40000 # 256KB

config INTEL_GMA_BCLV_OFFSET
	default 0xc8258

config INTEL_GMA_BCLV_WIDTH
	default 32

config INTEL_GMA_BCLM_OFFSET
	default 0xc8254

config INTEL_GMA_BCLM_WIDTH
	default 32

endif