/* SPDX-License-Identifier: GPL-2.0-or-later */

#include <baseboard/variants.h>
#include <chip.h>
#include <device/device.h>
#include <device/pci_ids.h>
#include <device/pci_ops.h>
#include <ec/google/chromeec/ec.h>
#include <intelblocks/power_limit.h>

const struct cpu_power_limits limits[] = {
	/* SKU_ID, TDP (Watts), pl1_min, pl1_max, pl2_min, pl2_max, pl4 */
	{ PCI_DID_INTEL_ADL_P_ID_10, 15, 15000, 15000,  55000,  55000, 123000 },
	{ PCI_DID_INTEL_ADL_P_ID_7, 15, 15000, 15000,  55000,  55000, 123000 },
	{ PCI_DID_INTEL_ADL_P_ID_6, 15, 15000, 15000,  55000,  55000, 123000 },
	{ PCI_DID_INTEL_ADL_P_ID_5, 28, 28000, 28000,  64000,  64000,  90000 },
	{ PCI_DID_INTEL_ADL_P_ID_3, 28, 28000, 28000,  64000,  64000, 140000 },
	{ PCI_DID_INTEL_ADL_P_ID_5, 45, 45000, 45000,  95000,  95000, 125000 },
	{ PCI_DID_INTEL_ADL_P_ID_4, 45, 45000, 45000, 115000, 115000, 215000 },
	{ PCI_DID_INTEL_ADL_P_ID_3, 45, 45000, 45000, 115000, 115000, 215000 },
	{ PCI_DID_INTEL_ADL_P_ID_1, 45, 45000, 45000,  95000,  95000, 125000 },
};

const struct system_power_limits sys_limits[] = {
	/* SKU_ID, TDP (Watts), psys_pl2 (Watts) */
	{ PCI_DID_INTEL_ADL_P_ID_10, 15, 135 },
	{ PCI_DID_INTEL_ADL_P_ID_7, 15, 135 },
	{ PCI_DID_INTEL_ADL_P_ID_6, 15, 135 },
	{ PCI_DID_INTEL_ADL_P_ID_5, 28, 230 },
	{ PCI_DID_INTEL_ADL_P_ID_3, 28, 230 },
	{ PCI_DID_INTEL_ADL_P_ID_5, 45, 230 },
	{ PCI_DID_INTEL_ADL_P_ID_4, 45, 230 },
	{ PCI_DID_INTEL_ADL_P_ID_3, 45, 230 },
	{ PCI_DID_INTEL_ADL_P_ID_1, 45, 230 },
};

/*
 * Psys_pmax considerations.
 *
 * Given the hardware design in brask, the serial shunt resistor is 0.005ohm.
 * The full scale of hardware PSYS signal 1.6v maps to system current 13.52A
 * instead of real system power. The equation is shown below:
 * PSYS = 1.6v = (0.005ohm x 13.52A) x 50 (INA213, gain 50V/V) x R501/(R501 + R510)
 * R501/(R501 + R510) = 0.47 = 15K / (15K + 16.9K)
 *
 * The Psys_pmax is a SW setting which tells IMVP9.1 the mapping b/w system input
 * current and the actual system power. Since there is no voltage information
 * from PSYS, different voltage input would map to different Psys_pmax settings:
 * For Type-C 15V, the Psys_pmax should be 15v x 13.52A = 202.8W
 * For Type-C 20V, the Psys_pmax should be 20v x 13.52A = 270.4W
 * For a barrel jack, the Psys_pmax should be 19.5v x 13.52A = 263.6W
 *
 * Imagine that there is a type-c 100W (20V/5A) connected to DUT w/ full loading,
 * and the Psys_pmax setting is 270.4W. Then IMVP9.1 can calculate the current system
 * power = 270.4W * 5A / 13.52A = 100W, which is the actual system power.
 */
const struct psys_config psys_config = {
	.efficiency = 97,
	.psys_imax_ma = 13520,
	.bj_volts_mv = 19500
};

void variant_devtree_update(void)
{
	size_t total_entries = ARRAY_SIZE(limits);
	variant_update_psys_power_limits(limits, sys_limits, total_entries, &psys_config);
	variant_update_power_limits(limits, total_entries);
}