mainboard: add Supermicro X9SCL/X9SCM
Boots to Linux.
Works:
- CPU (Core i3-2120 tested)
- Memory (one 1GB 1Rx8 PC3-10600E module tested)
- Slots 4, 6, 7
To fix/improve:
- SuperIO hardware monitor setup for PECI and fan control
- SuperIO ASL in DSDT (e.g. UART Devices)
- PEG PCIe lanes (should show x8 max width instead of x16 on 0:1.0 for Slot 7)
Untested:
- IPMI where BMC is fully implemented (X9SC[LM](+)-F variants)
- GbE on X9SCL+-F (where there are two 82574L instead of one)
- Slot 5 (x4 on 0:06.0) (only applicable to X9SCM variants)
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Change-Id: I985db89d67de21bbafbdc34d7044496434a6eb17
Depends-On: I5b7599746195cfa996a48320404a8dbe6820483a, I1206746332c9939a78b67e7b48d3098bdef8a2ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38346
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
diff --git a/src/mainboard/supermicro/x9scl/devicetree.cb b/src/mainboard/supermicro/x9scl/devicetree.cb
new file mode 100644
index 0000000..9236f6f
--- /dev/null
+++ b/src/mainboard/supermicro/x9scl/devicetree.cb
@@ -0,0 +1,127 @@
+chip northbridge/intel/sandybridge
+ device cpu_cluster 0 on
+ chip cpu/intel/model_206ax # FIXME: check all registers
+ register "c1_acpower" = "1"
+ register "c1_battery" = "1"
+ register "c2_acpower" = "3"
+ register "c2_battery" = "3"
+ register "c3_acpower" = "5"
+ register "c3_battery" = "5"
+ device lapic 0x0 on end
+ device lapic 0xacac off end
+ end
+ end
+ device domain 0 on
+ subsystemid 0x15d9 0x0624 inherit
+ device pci 00.0 on end # Host bridge
+ device pci 01.0 on end # PEG
+ device pci 01.1 on end # PEG
+ device pci 02.0 off end # iGPU
+ device pci 06.0 on end # PEG
+ chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH
+ register "c2_latency" = "0x0065"
+ register "gen1_dec" = "0x00fc0a01" # NCT6776 SuperIO (0x0a00-0aff)
+ register "gen2_dec" = "0x00fc1641" # WPCM450 SuperIO (0x1600-16ff)
+ register "gen3_dec" = "0x00040ca1" # IPMI KCS (0x0ca0-0ca3)
+ register "gen4_dec" = "0x001c03e1" # 3rd UART (0x03e0-03ff)
+ register "pcie_port_coalesce" = "1"
+ register "sata_interface_speed_support" = "0x3"
+ register "sata_port_map" = "0x3f"
+ register "spi_lvscc" = "0x2005"
+ register "spi_uvscc" = "0x2005"
+ device pci 16.0 off end # Management Engine Interface 1
+ device pci 16.1 off end # Management Engine Interface 2
+ device pci 16.2 off end # Management Engine IDE-R
+ device pci 16.3 off end # Management Engine KT
+ device pci 19.0 on # Intel Gigabit Ethernet (not for X9SCL+-F)
+ subsystemid 0x15d9 0x1502
+ end
+ device pci 1a.0 on end # USB2 EHCI #2
+ device pci 1b.0 off end # High Definition Audio
+ device pci 1c.0 on end # PCIe Port #1
+ device pci 1c.1 off end # PCIe Port #2
+ device pci 1c.2 off end # PCIe Port #3
+ device pci 1c.3 off end # PCIe Port #4
+ device pci 1c.4 on # PCIe Port #5
+ device pci 00.0 on end # primary 574 GigE
+ end
+ device pci 1c.5 off end # PCIe Port #6
+ device pci 1c.6 on # PCIe Port #7
+ device pci 00.0 on end # secondary 574 GigE on X9SCL+-F
+ end
+ device pci 1c.7 off end # PCIe Port #8
+ device pci 1d.0 on end # USB2 EHCI #1
+ device pci 1e.0 on # PCI bridge
+ device pci 03.0 on end # Matrox G200e in BMC
+ end
+ device pci 1f.0 on # LPC bridge
+ chip superio/nuvoton/nct6776
+ device pnp 2e.0 off end # Floppy
+ device pnp 2e.1 off end # Parallel port
+ device pnp 2e.2 on # COM1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ device pnp 2e.3 on # COM2, IR
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ end
+ device pnp 2e.5 on # Keyboard
+ io 0x60 = 0x060
+ io 0x62 = 0x064
+ irq 0x70 = 1
+ irq 0x72 = 12
+ end
+ device pnp 2e.6 off end # CIR
+ device pnp 2e.7 off end # GPIO6
+ device pnp 2e.107 off end # GPIO7
+ device pnp 2e.207 off end # GPIO8
+ device pnp 2e.307 off end # GPIO9
+ device pnp 2e.8 off end # WDT
+ device pnp 2e.108 on end # GPIO0
+ device pnp 2e.208 off end # GPIOA
+ device pnp 2e.308 on # GPIOBASE
+ io 0x60 = 0xa80
+ end
+ device pnp 2e.109 off end # GPIO1
+ device pnp 2e.209 on # GPIO2
+ end
+ device pnp 2e.309 on # GPIO3
+ end
+ device pnp 2e.409 off end # GPIO4
+ device pnp 2e.509 off end # GPIO5
+ device pnp 2e.609 off end # GPIO6
+ device pnp 2e.709 off end # GPIO7
+ device pnp 2e.a off end # ACPI
+ device pnp 2e.b on # HWM, front panel LED
+ io 0x60 = 0xa30
+ io 0x62 = 0
+ end
+ device pnp 2e.d off end # VID
+ device pnp 2e.e off end # CIR WAKE-UP
+ device pnp 2e.f off end # GPIO
+ device pnp 2e.14 off end # SVID
+ device pnp 2e.16 off end # Deep sleep
+ device pnp 2e.17 off end # GPIOA
+ end
+ chip drivers/ipmi
+ register "wait_for_bmc" = "1"
+ register "bmc_boot_timeout" = "60"
+ device pnp ca2.0 off end # IPMI KCS
+ end
+ chip superio/nuvoton/wpcm450
+ device pnp 164e.2 on
+ io 0x60 = 0x03e8
+ irq 0x70 = 10
+ end
+ device pnp 164e.3 off end
+ device pnp 164e.6 off end
+ end
+ end
+ device pci 1f.2 on end # SATA Controller 1
+ device pci 1f.3 on end # SMBus
+ device pci 1f.5 off end # SATA Controller 2
+ device pci 1f.6 off end # Thermal
+ end
+ end
+end