/* SPDX-License-Identifier: GPL-2.0-or-later */

#include <acpi/acpi_device.h>
#include <baseboard/variants.h>
#include <console/console.h>
#include <device/device.h>
#include <drivers/amd/i2s_machine_dev/chip.h>
#include <drivers/i2c/generic/chip.h>
#include <drivers/i2c/hid/chip.h>
#include <drivers/usb/acpi/chip.h>
#include <ec/google/chromeec/ec.h>
#include <gpio.h>
#include <soc/iomap.h>
#include <soc/pci_devs.h>

extern struct chip_operations drivers_i2c_generic_ops;
extern struct chip_operations drivers_i2c_hid_ops;

WEAK_DEV_PTR(xhci1_bt);

static void update_hp_int_odl(void)
{
	const struct device *rt5682_dev = DEV_PTR(audio_rt5682);
	struct drivers_i2c_generic_config *cfg;
	struct acpi_gpio *gpio;
	struct soc_amd_picasso_config *soc_cfg;

	if (!variant_uses_codec_gpi())
		return;

	cfg = config_of(rt5682_dev);
	gpio = &cfg->irq_gpio;
	gpio->pins[0] = 62;

	/*
	 * When using CODEC_GPI for headphone jack interrupt, ACP_PME_EN and ACP_I2S_WAKE_EN
	 * need to be set to trigger I2S_WAKE event for headphone jack.
	 */
	soc_cfg = config_of_soc();
	soc_cfg->common_config.acp_config.acp_i2s_wake_enable = 1;
	soc_cfg->common_config.acp_config.acp_pme_enable = 1;
}

static void update_dmic_gpio(void)
{
	const struct device *machine_dev = DEV_PTR(acp_machine);
	struct drivers_amd_i2s_machine_dev_config *cfg;
	struct acpi_gpio *gpio;

	if (variant_uses_v3_schematics())
		return;

	cfg = config_of(machine_dev);
	gpio = &cfg->dmic_select_gpio;

	if (CONFIG(BOARD_GOOGLE_BASEBOARD_TREMBYLE))
		gpio->pins[0] = GPIO_13;
	else
		gpio->pins[0] = GPIO_6;

}

void variant_audio_update(void)
{
	update_dmic_gpio();
	update_hp_int_odl();
}

/*
 * Removes reset_gpio from usb device in device tree.
 *
 * debug_device_name is used for debug messaging only.
 */
static void remove_usb_device_reset_gpio(const struct device *usb_dev)
{

	struct drivers_usb_acpi_config *usb_cfg;
	/* config_of dies on failure, so a NULL check is not required */
	usb_cfg = config_of(usb_dev);
	usb_cfg->reset_gpio.pin_count = 0;
}

/*
 * The bluetooth device may be on XHCI0 or XHCI1 depending on SOC.
 * There's no harm in removing reset_gpio from both here.
 */
static void baseboard_trembyle_remove_bluetooth_reset_gpio(void)
{
	remove_usb_device_reset_gpio(DEV_PTR(xhci0_bt));
	remove_usb_device_reset_gpio(DEV_PTR(xhci1_bt));
}

void variant_bluetooth_update(void)
{
	if (CONFIG(BOARD_GOOGLE_BASEBOARD_DALBOZ) || variant_uses_v3_schematics())
		return;

	baseboard_trembyle_remove_bluetooth_reset_gpio();
}

void variant_touchscreen_update(void)
{
	DEVTREE_CONST struct device *mmio_dev = DEV_PTR(i2c_2);
	struct device *child = NULL;

	/*
	 * By default, devicetree/overridetree entries for touchscreen device are configured to
	 * match v3.6 of reference schematics. So, if the board is using v3.6+ schematics, no
	 * additional work is required here. For maintaining support for pre-v3.6 boards, rest
	 * of the code in this function finds all entries that correspond to touchscreen
	 * devices (identified by reset_gpio being set to GPIO_140) and updates them as per
	 * pre-v3.6 version of schematics:
	 * 1. reset_gpio is marked as active high.
	 */
	if (variant_uses_v3_6_schematics())
		return;

	while ((child = dev_bus_each_child(mmio_dev->link_list, child)) != NULL) {
		struct drivers_i2c_generic_config *cfg;

		if (child->chip_ops == &drivers_i2c_generic_ops) {
			cfg = config_of(child);
		} else if (child->chip_ops == &drivers_i2c_hid_ops) {
			struct drivers_i2c_hid_config *hid_cfg;
			hid_cfg = config_of(child);
			cfg = &hid_cfg->generic;
		} else {
			continue;
		}

		/* If reset_gpio is set to GPIO_140, assume that this is touchscreen device. */
		if (cfg->reset_gpio.pins[0] != GPIO_140)
			continue;

		cfg->reset_gpio.active_low = 0;
		cfg->enable_gpio.pin_count = 0;
		cfg->enable_gpio.pins[0] = 0;
	}
}