#define ASSEMBLY 1
#define __PRE_RAM__

#define RAMINIT_SYSINFO 1
#define CACHE_AS_RAM_ADDRESS_DEBUG 0

#define SET_NB_CFG_54 1 

//used by raminit
#define QRANK_DIMM_SUPPORT 1

//used by incoherent_ht
//#define K8_ALLOCATE_IO_RANGE 1

//used by init_cpus and fidvid
#define K8_SET_FIDVID 0
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1

#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif

#include <stdint.h>
#include <string.h>
#include <device/pci_def.h>
#include <device/pci_ids.h>
#include <arch/io.h>
#include <device/pnp_def.h>
#include <arch/romcc_io.h>
#include <cpu/x86/lapic.h>
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"


#if 0 
static void post_code(uint8_t value) {
#if 1
        int i;
        for(i=0;i<0x80000;i++) {
                outb(value, 0x80);
        }
#endif
}
#endif
#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include <cpu/amd/model_fxx_rev.h>
#include "southbridge/amd/amd8111/amd8111_early_smbus.c"
#include "northbridge/amd/amdk8/raminit.h"
#include "cpu/amd/model_fxx/apic_timer.c"
#endif


#include "cpu/x86/lapic/boot_cpu.c"
#include "northbridge/amd/amdk8/reset_test.c"

#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"

#include "lib/delay.c"

#include "northbridge/amd/amdk8/debug.c"
#include "cpu/amd/mtrr/amd_earlymtrr.c"
#include "superio/winbond/w83627hf/w83627hf_early_serial.c"

#include "northbridge/amd/amdk8/setup_resource_map.c"

#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)

#include "southbridge/amd/amd8111/amd8111_early_ctrl.c"

static void memreset_setup(void)
{
	//GPIO on amd8111 to enable MEMRST ????
        outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16);  //REVC_MEMRST_EN=1
        outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}

static void memreset(int controllers, const struct mem_controller *ctrl)
{
}

static inline void activate_spd_rom(const struct mem_controller *ctrl)
{
#define SMBUS_HUB 0x18
        int ret,i;
        unsigned device=(ctrl->channel0[0])>>8;
        /* the very first write always get COL_STS=1 and ABRT_STS=1, so try another time*/
        i=2;
        do {
                ret = smbus_write_byte(SMBUS_HUB, 0x01, device);
        } while ((ret!=0) && (i-->0));

        smbus_write_byte(SMBUS_HUB, 0x03, 0);
}
#if 0
static inline void change_i2c_mux(unsigned device)
{
#define SMBUS_HUB 0x18
        int ret, i;
        print_debug("change_i2c_mux i="); print_debug_hex8(device); print_debug("\r\n");
        i=2;
        do {
                ret = smbus_write_byte(SMBUS_HUB, 0x01, device);
                print_debug("change_i2c_mux 1 ret="); print_debug_hex32(ret); print_debug("\r\n");
        } while ((ret!=0) && (i-->0));
        ret = smbus_write_byte(SMBUS_HUB, 0x03, 0);
        print_debug("change_i2c_mux 2 ret="); print_debug_hex32(ret); print_debug("\r\n");
}
#endif

static inline int spd_read_byte(unsigned device, unsigned address)
{
        return smbus_read_byte(device, address);
}

#include "northbridge/amd/amdk8/amdk8.h"
#include "northbridge/amd/amdk8/coherent_ht.c"

#include "northbridge/amd/amdk8/incoherent_ht.c"

#include "northbridge/amd/amdk8/raminit_f.c"

#include "lib/generic_sdram.c"

 /* tyan does not want the default */
#include "resourcemap.c" 

#include "cpu/amd/dualcore/dualcore.c"

#define RC0 ((1<<0)<<8)
#define RC1 ((1<<1)<<8)
#define RC2 ((1<<2)<<8)
#define RC3 ((1<<3)<<8)

#define DIMM0 0x50
#define DIMM1 0x51
#define DIMM2 0x52
#define DIMM3 0x53
#define DIMM4 0x54
#define DIMM5 0x55
#define DIMM6 0x56
#define DIMM7 0x57


#include "cpu/amd/car/copy_and_run.c"
#include "cpu/amd/car/post_cache_as_ram.c"

#include "cpu/amd/model_fxx/init_cpus.c"

#include "cpu/amd/model_fxx/fidvid.c"
#endif

#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"

#if CONFIG_USE_FAILOVER_IMAGE==0

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
			//first node
                        RC0|DIMM0, RC0|DIMM2, 0, 0,
                        RC0|DIMM1, RC0|DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
			//second node
                        RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
                        RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
#endif
#if CONFIG_MAX_PHYSICAL_CPUS > 2
                        // third node
                        RC2|DIMM0, RC2|DIMM2, 0, 0,
                        RC2|DIMM1, RC2|DIMM3, 0, 0,
                        // four node
                        RC3|DIMM0, RC3|DIMM2, RC3|DIMM4, RC3|DIMM6,
                        RC3|DIMM1, RC3|DIMM3, RC3|DIMM5, RC3|DIMM7,
#endif

	};

	struct sys_info *sysinfo = (void*)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);

        int needs_reset;
        unsigned bsp_apicid = 0;
#if K8_SET_FIDVID == 1
	struct cpuid_result cpuid1;
#endif

        if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */

		enumerate_ht_chain();

		/* Setup the rom access for 4M */
		amd8111_enable_rom();
        }

        if (bist == 0) {
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
        }

//	post_code(0x32);

 	w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
        uart_init();
        console_init();

//	dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
	
	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

        print_debug("*sysinfo range: ["); print_debug_hex32(sysinfo); print_debug(",");  print_debug_hex32((unsigned long)sysinfo+sizeof(struct sys_info)); print_debug(")\r\n");

        setup_mb_resource_map();
#if 0
        dump_pci_device(PCI_DEV(0, 0x18, 0));
	dump_pci_device(PCI_DEV(0, 0x19, 0));
#endif

	print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");

#if CONFIG_MEM_TRAIN_SEQ == 1
        set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram 
#endif
	setup_coherent_ht_domain(); // routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
        // It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain, 
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case) 
	 */
        start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif
	
	/* it will set up chains and store link pair for optimization later */
        ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

#if 0
	//it your CPU min fid is 1G, you can change HT to 1G and FID to max one time.
        needs_reset = optimize_link_coherent_ht();
        needs_reset |= optimize_link_incoherent_ht(sysinfo);
#endif

#if K8_SET_FIDVID == 1
	/* Check to see if processor is capable of changing FIDVID  */
	/* otherwise it will throw a GP# when reading FIDVID_STATUS */
	cpuid1 = cpuid(0x80000007);
	if( (cpuid1.edx & 0x6) == 0x6 ) {

        {
		/* Read FIDVID_STATUS */
                msr_t msr;
                msr=rdmsr(0xc0010042);
                print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\r\n");

        }

	enable_fid_change();

	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

        init_fidvid_bsp(bsp_apicid);

        // show final fid and vid
        {
                msr_t msr;
                msr=rdmsr(0xc0010042);
                print_debug("end   msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\r\n"); 

        }

	} else {
		print_debug("Changing FIDVID not supported\n");
	}

#endif

#if 1
	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);

        // fidvid change will issue one LDTSTOP and the HT change will be effective too
        if (needs_reset) {
                print_info("ht reset -\r\n");
                soft_reset_x(sysinfo->sbbusn, sysinfo->sbdn);
        }
#endif
	allow_all_aps_stop(bsp_apicid);

        //It's the time to set ctrl in sysinfo now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();

#if 0
	int i;
	for(i=0;i<4;i++) {
		activate_spd_rom(&cpu[i]);
		dump_smbus_registers();
	}
#endif

#if 0
        for(i=1;i<256;i<<=1) {
                change_i2c_mux(i);
                dump_smbus_registers();
        }
#endif

	memreset_setup();

	//do we need apci timer, tsc...., only debug need it for better output
        /* all ap stopped? */
//        init_timer(); // Need to use TMICT to synconize FID/VID

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

#if 0
        print_pci_devices();
#endif

#if 0
//        dump_pci_devices();
        dump_pci_device_index_wait(PCI_DEV(0, 0x18, 2), 0x98);
	dump_pci_device_index_wait(PCI_DEV(0, 0x19, 2), 0x98);
#endif

        post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now

}
#endif