adding preliminary, and almost certainly wrong, rumba support.
This is just a skeleton, basically, and will most likely not even
compile yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2164 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
diff --git a/src/cpu/amd/model_gx2/Config.lb b/src/cpu/amd/model_gx2/Config.lb
new file mode 100644
index 0000000..b643d77
--- /dev/null
+++ b/src/cpu/amd/model_gx2/Config.lb
@@ -0,0 +1,6 @@
+dir /cpu/x86/tsc
+dir /cpu/x86/fpu
+dir /cpu/x86/mmx
+dir /cpu/x86/lapic
+dir /cpu/x86/cache
+driver model_gx2_init.o
diff --git a/src/cpu/amd/model_gx2/cpu_setup.inc b/src/cpu/amd/model_gx2/cpu_setup.inc
new file mode 100644
index 0000000..ff35d3b
--- /dev/null
+++ b/src/cpu/amd/model_gx2/cpu_setup.inc
@@ -0,0 +1,70 @@
+/*
+ freebios/src/northbridge/nsc/gx1/cpu_setup.inc
+
+ Copyright (c) 2002 Christer Weinigel <wingel@hack.org>
+
+ Initialize the GX1 CPU configuration registers
+*/
+
+/* copied for gx2 for ron minnich, as a placeholder */
+
+/* USES: esi, ecx, eax */
+
+#include <cpu/amd/gx2def.h>
+
+ movl %eax, %ebp /* preserve bist */
+
+cpu_setup_start:
+ leal cpu_setup_table, %esi
+ movl $cpu_setup_len, %ecx
+
+cpu_setup_loop:
+ movw (%esi), %ax
+ addl $2, %esi
+ outb %al, $0x22
+ movb %ah, %al
+ outb %al, $0x23
+ loop cpu_setup_loop
+
+ movb $0xff, %al /* DIR1 -- Identification Register 1 */
+ outb %al, $0x22
+ inb $0x23, %al
+ cmpb $0x63, %al /* Revision for GXLV rev 3 */
+ jbe cpu_no_ccr4
+
+ movb $0xe8, %al /* CCR4 */
+ outb %al, $0x22
+ inb $0x23, %al
+ orb $0x20, %al /* Enable FPU Fast Mode */
+ outb %al, $0x23
+
+ movb $0xf0, %al /* PCR1 --- Performace Control */
+ outb %al, $0x22
+ inb $0x23, %al
+ orb $0x02, %al /* Incrementor on, whatever that is */
+ outb %al, $0x23
+
+ movb $0x20, %al /* PCR0 --- Performace Control */
+ outb %al, $0x22
+ inb $0x23, %al
+ orb $0x20, %al /* Must be 1 according to data book */
+ orb $0x04, %al /* Incrementor Margin 10 */
+ outb %al, $0x23
+cpu_no_ccr4:
+
+ jmp cpu_setup_end
+
+cpu_setup_table:
+ .byte 0xc1, 0x00 /* NO SMIs */
+ .byte 0xc3, 0x14 /* Enable CPU config register */
+ .byte 0x20, 0x00
+ .byte 0xb8, GX_BASE>>30 /* Enable GXBASE address */
+ .byte 0xc2, 0x00
+ .byte 0xe8, 0x98
+ .byte 0xc3, 0xf8 /* Enable CPU config register */
+cpu_setup_len = (.-cpu_setup_table)/2
+
+cpu_setup_end:
+ nop
+
+ movl %ebp, %eax /* Restore bist */
diff --git a/src/cpu/amd/model_gx2/gx_setup.inc b/src/cpu/amd/model_gx2/gx_setup.inc
new file mode 100644
index 0000000..ce9d46d
--- /dev/null
+++ b/src/cpu/amd/model_gx2/gx_setup.inc
@@ -0,0 +1,47 @@
+/*
+ freebios/src/northbridge/nsc/gx2/gx_setup.inc
+
+ Copyright (c) 2002 Christer Weinigel <wingel@hack.org>
+
+ Setup the GX_BASE registers on a National Semiconductor Geode CPU
+*/
+
+#include <cpu/amd/gx2def.h>
+
+ movl %eax, %ebp /* Preserve bist */
+
+gx_setup_start:
+ leal gx_setup_table, %esi
+ movl $gx_setup_len, %ecx
+ movl $GX_BASE, %edi
+
+gx_setup_loop:
+ movw (%esi), %di /* Only read the low word of address */
+ addl $4, %esi
+ movl (%esi), %eax /* Data */
+ addl $4, %esi
+ movl %eax, (%edi)
+ loop gx_setup_loop
+
+ jmp gx_setup_end
+
+gx_setup_table:
+ /* Allow writes to config registers */
+ .long DC_UNLOCK, DC_UNLOCK_MAGIC
+ .long DC_GENERAL_CFG, 0
+ .long DC_UNLOCK, 0
+
+ .long BC_DRAM_TOP, 0x3fffffff
+ .long BC_XMAP_1, 0x60
+ .long BC_XMAP_2, 0
+ .long BC_XMAP_3, 0
+
+ .long MC_BANK_CFG, 0x00700070 /* No DIMMS installed */
+ .long MC_MEM_CNTRL1, XBUSARB
+ .long MC_GBASE_ADD, 0x7ff /* Almost 1GB */
+gx_setup_len = (.-gx_setup_table)/8
+
+gx_setup_end:
+ nop
+
+ movl %ebp, %eax /* Restore bist */
diff --git a/src/cpu/amd/model_gx2/model_gx1_init.c b/src/cpu/amd/model_gx2/model_gx1_init.c
new file mode 100644
index 0000000..8558872
--- /dev/null
+++ b/src/cpu/amd/model_gx2/model_gx1_init.c
@@ -0,0 +1,101 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <string.h>
+#include <cpu/cpu.h>
+#include <cpu/x86/lapic.h>
+#include <cpu/x86/cache.h>
+
+#if 0
+#include <cpu/amd/gx2def.h>
+#include <arch/io.h>
+
+static void gx2_cpu_setup(void)
+{
+ unsigned char rreg;
+ unsigned char cpu_table[] = {
+ 0xc1, 0x00, /* NO SMIs */
+ 0xc3, 0x14, /* Enable CPU config register */
+ 0x20, 0x00, /* */
+ 0xb8, GX_BASE>>30, /* Enable GXBASE address */
+ 0xc2, 0x00,
+ 0xe8, 0x98,
+ 0xc3, 0xf8, /* Enable CPU config register */
+ 0x00, 0x00
+ };
+ unsigned char *cPtr = cpu_table;
+
+ while(rreg = *cPtr++) {
+ unsigned char rval = *cPtr++;
+ outb(rreg, 0x22);
+ outb(rval, 0x23);
+ }
+
+ outb(0xff, 0x22); /* DIR1 -- Identification register 1 */
+ if(inb(0x23) > 0x63) { /* Rev greater than R3 */
+ outb(0xe8, 0x22);
+ outb(inb(0x23) | 0x20, 0x23); /* Enable FPU Fast Mode */
+
+ outb(0xf0, 0x22);
+ outb(inb(0x23) | 0x02, 0x23); /* Incrementor on */
+
+ outb(0x20, 0x22);
+ outb(inb(0x23) | 0x24, 0x23); /* Bit 5 must be on */
+ /* Bit 2 Incrementor margin 10 */
+
+ }
+}
+
+static void gx2_gx_setup(void)
+{
+unsigned long gx_setup_table[] = {
+ GX_BASE + DC_UNLOCK, DC_UNLOCK_MAGIC,
+ GX_BASE + DC_GENERAL_CFG, 0,
+ GX_BASE + DC_UNLOCK, 0,
+ GX_BASE + BC_DRAM_TOP, 0x3fffffff,
+ GX_BASE + BC_XMAP_1, 0x60,
+ GX_BASE + BC_XMAP_2, 0,
+ GX_BASE + BC_XMAP_3, 0,
+ GX_BASE + MC_BANK_CFG, 0x00700070,
+ GX_BASE + MC_MEM_CNTRL1, XBUSARB,
+ GX_BASE + MC_GBASE_ADD, 0xff,
+ 0, 0
+ };
+
+unsigned long *gxPtr = gx_setup_table;
+unsigned long *gxdPtr;
+unsigned long addr;
+
+ while(addr = *gxPtr++) {
+ gxdPtr = (unsigned long *)addr;
+ *gxdPtr = *gxPtr++;
+ }
+}
+#endif
+
+static void model_gx2_init(device_t dev)
+{
+#if 0
+ gx2_cpu_setup();
+ gx2_gx_setup();
+#endif
+ /* Turn on caching if we haven't already */
+ x86_enable_cache();
+
+ /* Enable the local cpu apics */
+ setup_lapic();
+};
+
+static struct device_operations cpu_dev_ops = {
+ .init = model_gx2_init,
+};
+
+static struct cpu_device_id cpu_table[] = {
+ { X86_VENDOR_CYRIX, 0x0540 },
+ { 0, 0 },
+};
+
+static struct cpu_driver driver __cpu_driver = {
+ .ops = &cpu_dev_ops,
+ .id_table = cpu_table,
+};
diff --git a/src/mainboard/amd/rumba/Config.lb b/src/mainboard/amd/rumba/Config.lb
new file mode 100644
index 0000000..fe63c0e
--- /dev/null
+++ b/src/mainboard/amd/rumba/Config.lb
@@ -0,0 +1,145 @@
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+ default ROM_SECTION_SIZE = FALLBACK_SIZE
+ default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+ default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE )
+ default ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+
+if HAVE_PIRQ_TABLE object irq_tables.o end
+#object reset.o
+
+##
+## Romcc output
+##
+makerule ./failover.E
+ depends "$(MAINBOARD)/failover.c ./romcc"
+ action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./failover.inc
+ depends "$(MAINBOARD)/failover.c ./romcc"
+ action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./auto.E
+ depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ action "./romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+makerule ./auto.inc
+ depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ action "./romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
+if USE_FALLBACK_IMAGE
+ mainboardinit cpu/x86/16bit/reset16.inc
+ ldscript /cpu/x86/16bit/reset16.lds
+else
+ mainboardinit cpu/x86/32bit/reset32.inc
+ ldscript /cpu/x86/32bit/reset32.lds
+end
+
+### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+###
+### This is the early phase of linuxBIOS startup
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if USE_FALLBACK_IMAGE
+ ldscript /arch/i386/lib/failover.lds
+ mainboardinit ./failover.inc
+end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/amd/model_gx1/cpu_setup.inc
+mainboardinit cpu/amd/model_gx1/gx_setup.inc
+mainboardinit ./auto.inc
+
+##
+## Include the secondary Configuration files
+##
+dir /pc80
+config chip.h
+
+chip northbridge/amd/gx2
+ device pci_domain 0 on
+ device pci 0.0 on end
+ chip southbridge/amd/cs5535
+ device pci 12.0 on
+ device pci 12.1 off end # SMI
+ device pci 12.2 on end # IDE
+ device pci 12.3 off end # Audio
+ device pci 12.4 off end # VGA
+ end
+ end
+ end
+
+ chip cpu/amd/model_gx2
+ end
+
+end
+
diff --git a/src/mainboard/amd/rumba/Options.lb b/src/mainboard/amd/rumba/Options.lb
new file mode 100644
index 0000000..df3d1bd
--- /dev/null
+++ b/src/mainboard/amd/rumba/Options.lb
@@ -0,0 +1,160 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses HAVE_OPTION_TABLE
+uses USE_OPTION_TABLE
+uses CONFIG_ROM_STREAM
+uses IRQ_SLOT_COUNT
+uses MAINBOARD
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses LINUXBIOS_EXTRA_VERSION
+uses ARCH
+uses FALLBACK_SIZE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses _RAMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses HAVE_MP_TABLE
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_CONSOLE_SERIAL8250
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses CONFIG_UDELAY_TSC
+uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE = 256*1024
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## no MP table
+##
+default HAVE_MP_TABLE=0
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=0
+
+## Delay timer options
+##
+default CONFIG_UDELAY_TSC=1
+default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=2
+#object irq_tables.o
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=0
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+default FALLBACK_SIZE = 131072
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default USE_OPTION_TABLE = 0
+
+default _RAMBASE = 0x00004000
+
+default CONFIG_ROM_STREAM = 1
+
+##
+## The default compiler
+##
+default CROSS_COMPILE=""
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG 1 system is unusable
+## ALERT 2 action must be taken immediately
+## CRIT 3 critical conditions
+## ERR 4 error conditions
+## WARNING 5 warning conditions
+## NOTICE 6 normal but significant condition
+## INFO 7 informational
+## DEBUG 8 debug-level messages
+## SPEW 9 Way too many details
+
+## Request this level of debugging output
+default DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default MAXIMUM_CONSOLE_LOGLEVEL=8
+
+end
+
diff --git a/src/mainboard/amd/rumba/auto.c b/src/mainboard/amd/rumba/auto.c
new file mode 100644
index 0000000..4caac51
--- /dev/null
+++ b/src/mainboard/amd/rumba/auto.c
@@ -0,0 +1,55 @@
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+//#include "southbridge/intel/i440bx/i440bx_early_smbus.c"
+//#include "superio/NSC/pc97317/pc97317_early_serial.c"
+//#include "northbridge/intel/i440bx/raminit.h"
+#include "cpu/x86/bist.h"
+
+#define SERIAL_DEV PNP_DEV(0x2e, PC97317_SP1)
+
+//#include "debug.c"
+//#include "lib/delay.c"
+
+#include "northbridge/amd/gx2/raminit.c"
+
+static void main(unsigned long bist)
+{
+// pc97317_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ uart_init();
+ console_init();
+
+ /* Halt if there was a built in self test failure */
+ report_bist_failure(bist);
+
+ sdram_init();
+
+ /* Check all of memory */
+#if 0
+ ram_check(0x00000000, msr.lo);
+#endif
+#if 0
+ static const struct {
+ unsigned long lo, hi;
+ } check_addrs[] = {
+ /* Check 16MB of memory @ 0*/
+ { 0x00000000, 0x01000000 },
+#if TOTAL_CPUS > 1
+ /* Check 16MB of memory @ 2GB */
+ { 0x80000000, 0x81000000 },
+#endif
+ };
+ int i;
+ for(i = 0; i < sizeof(check_addrs)/sizeof(check_addrs[0]); i++) {
+ ram_check(check_addrs[i].lo, check_addrs[i].hi);
+ }
+#endif
+}
diff --git a/src/mainboard/amd/rumba/chip.h b/src/mainboard/amd/rumba/chip.h
new file mode 100644
index 0000000..90cfe88
--- /dev/null
+++ b/src/mainboard/amd/rumba/chip.h
@@ -0,0 +1,5 @@
+extern struct chip_operations mainboard_amd_rumba_ops;
+
+struct mainboard_amd_rumba_config {
+ int nothing;
+};
diff --git a/src/mainboard/amd/rumba/cmos.layout b/src/mainboard/amd/rumba/cmos.layout
new file mode 100644
index 0000000..5ba4c03
--- /dev/null
+++ b/src/mainboard/amd/rumba/cmos.layout
@@ -0,0 +1,74 @@
+entries
+
+#start-bit length config config-ID name
+#0 8 r 0 seconds
+#8 8 r 0 alarm_seconds
+#16 8 r 0 minutes
+#24 8 r 0 alarm_minutes
+#32 8 r 0 hours
+#40 8 r 0 alarm_hours
+#48 8 r 0 day_of_week
+#56 8 r 0 day_of_month
+#64 8 r 0 month
+#72 8 r 0 year
+#80 4 r 0 rate_select
+#84 3 r 0 REF_Clock
+#87 1 r 0 UIP
+#88 1 r 0 auto_switch_DST
+#89 1 r 0 24_hour_mode
+#90 1 r 0 binary_values_enable
+#91 1 r 0 square-wave_out_enable
+#92 1 r 0 update_finished_enable
+#93 1 r 0 alarm_interrupt_enable
+#94 1 r 0 periodic_interrupt_enable
+#95 1 r 0 disable_clock_updates
+#96 288 r 0 temporary_filler
+0 384 r 0 reserved_memory
+384 1 e 4 boot_option
+385 1 e 4 last_boot
+386 1 e 1 ECC_memory
+388 4 r 0 reboot_bits
+392 3 e 5 baud_rate
+400 1 e 1 power_on_after_fail
+412 4 e 6 debug_level
+416 4 e 7 boot_first
+420 4 e 7 boot_second
+424 4 e 7 boot_third
+428 4 h 0 boot_index
+432 8 h 0 boot_countdown
+1008 16 h 0 check_sum
+
+enumerations
+
+#ID value text
+1 0 Disable
+1 1 Enable
+2 0 Enable
+2 1 Disable
+4 0 Fallback
+4 1 Normal
+5 0 115200
+5 1 57600
+5 2 38400
+5 3 19200
+5 4 9600
+5 5 4800
+5 6 2400
+5 7 1200
+6 6 Notice
+6 7 Info
+6 8 Debug
+6 9 Spew
+7 0 Network
+7 1 HDD
+7 2 Floppy
+7 8 Fallback_Network
+7 9 Fallback_HDD
+7 10 Fallback_Floppy
+#7 3 ROM
+
+checksums
+
+checksum 392 1007 1008
+
+
diff --git a/src/mainboard/amd/rumba/debug.c b/src/mainboard/amd/rumba/debug.c
new file mode 100644
index 0000000..7eeabde
--- /dev/null
+++ b/src/mainboard/amd/rumba/debug.c
@@ -0,0 +1,66 @@
+
+static void print_debug_pci_dev(unsigned dev)
+{
+ print_debug("PCI: ");
+ print_debug_hex8((dev >> 16) & 0xff);
+ print_debug_char(':');
+ print_debug_hex8((dev >> 11) & 0x1f);
+ print_debug_char('.');
+ print_debug_hex8((dev >> 8) & 7);
+}
+
+static void print_pci_devices(void)
+{
+ device_t dev;
+ for(dev = PCI_DEV(0, 0, 0);
+ dev <= PCI_DEV(0, 0x1f, 0x7);
+ dev += PCI_DEV(0,0,1)) {
+ uint32_t id;
+ id = pci_read_config32(dev, PCI_VENDOR_ID);
+ if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+ (((id >> 16) & 0xffff) == 0xffff) ||
+ (((id >> 16) & 0xffff) == 0x0000)) {
+ continue;
+ }
+ print_debug_pci_dev(dev);
+ print_debug("\r\n");
+ }
+}
+
+static void dump_pci_device(unsigned dev)
+{
+ int i;
+ print_debug_pci_dev(dev);
+ print_debug("\r\n");
+
+ for(i = 0; i <= 255; i++) {
+ unsigned char val;
+ if ((i & 0x0f) == 0) {
+ print_debug_hex8(i);
+ print_debug_char(':');
+ }
+ val = pci_read_config8(dev, i);
+ print_debug_char(' ');
+ print_debug_hex8(val);
+ if ((i & 0x0f) == 0x0f) {
+ print_debug("\r\n");
+ }
+ }
+}
+
+static void dump_pci_devices(void)
+{
+ device_t dev;
+ for(dev = PCI_DEV(0, 0, 0);
+ dev <= PCI_DEV(0, 0x1f, 0x7);
+ dev += PCI_DEV(0,0,1)) {
+ uint32_t id;
+ id = pci_read_config32(dev, PCI_VENDOR_ID);
+ if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+ (((id >> 16) & 0xffff) == 0xffff) ||
+ (((id >> 16) & 0xffff) == 0x0000)) {
+ continue;
+ }
+ dump_pci_device(dev);
+ }
+}
diff --git a/src/mainboard/amd/rumba/failover.c b/src/mainboard/amd/rumba/failover.c
new file mode 100644
index 0000000..bdcb9ea
--- /dev/null
+++ b/src/mainboard/amd/rumba/failover.c
@@ -0,0 +1,32 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include "arch/romcc_io.h"
+#include "pc80/mc146818rtc_early.c"
+
+static unsigned long main(unsigned long bist)
+{
+ /* This is the primary cpu how should I boot? */
+ if (do_normal_boot()) {
+ goto normal_image;
+ }
+ else {
+ goto fallback_image;
+ }
+ normal_image:
+ asm volatile ("jmp __normal_image"
+ : /* outputs */
+ : "a" (bist) /* inputs */
+ : /* clobbers */
+ );
+ cpu_reset:
+ asm volatile ("jmp __cpu_reset"
+ : /* outputs */
+ : "a"(bist) /* inputs */
+ : /* clobbers */
+ );
+ fallback_image:
+ return bist;
+}
diff --git a/src/mainboard/amd/rumba/irq_tables.c b/src/mainboard/amd/rumba/irq_tables.c
new file mode 100644
index 0000000..636f129
--- /dev/null
+++ b/src/mainboard/amd/rumba/irq_tables.c
@@ -0,0 +1,31 @@
+/* This file was generated by getpir.c, do not modify!
+ (but if you do, please run checkpir on it to verify)
+ * Contains the IRQ Routing Table dumped directly from your memory, which BIOS sets up
+ *
+ * Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32+16*2, /* there can be total 2 devices on the bus */
+ 0x00, /* Where the interrupt router lies (bus) */
+ (0x12<<3)|0x0, /* Where the interrupt router lies (dev) */
+ 0x800, /* IRQs devoted exclusively to PCI usage */
+ 0x1078, /* Vendor */
+ 0x2, /* Device */
+ 0, /* Crap (miniport) */
+ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+ 0xdf, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ {
+ /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
+ {0x00,(0x0e<<3)|0x0, {{0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x01, 0x0deb8}}, 0x1, 0x0},
+ {0x00,(0x0f<<3)|0x0, {{0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x01, 0xdeb8}, {0x02, 0x0deb8}}, 0x2, 0x0},
+ }
+};
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+ return copy_pirq_routing_table(addr);
+}
diff --git a/src/mainboard/amd/rumba/mainboard.c b/src/mainboard/amd/rumba/mainboard.c
new file mode 100644
index 0000000..133d38f
--- /dev/null
+++ b/src/mainboard/amd/rumba/mainboard.c
@@ -0,0 +1,12 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <arch/io.h>
+#include "chip.h"
+
+struct chip_operations mainboard_amd_rumba_ops = {
+ CHIP_NAME("AMD Rumba mainboard ")
+};
+
diff --git a/src/mainboard/amd/rumba/reset.c b/src/mainboard/amd/rumba/reset.c
new file mode 100644
index 0000000..5796e17
--- /dev/null
+++ b/src/mainboard/amd/rumba/reset.c
@@ -0,0 +1,43 @@
+#if 0
+//#include "arch/romcc_io.h"
+#include <arch/io.h>
+
+typedef unsigned device_t;
+
+#define PCI_DEV(BUS, DEV, FN) ( \
+ (((BUS) & 0xFF) << 16) | \
+ (((DEV) & 0x1f) << 11) | \
+ (((FN) & 0x7) << 8))
+
+static void pci_write_config8(device_t dev, unsigned where, unsigned char value)
+{
+ unsigned addr;
+ addr = dev | where;
+ outl(0x80000000 | (addr & ~3), 0xCF8);
+ outb(value, 0xCFC + (addr & 3));
+}
+
+static void pci_write_config32(device_t dev, unsigned where, unsigned value)
+{
+ unsigned addr;
+ addr = dev | where;
+ outl(0x80000000 | (addr & ~3), 0xCF8);
+ outl(value, 0xCFC);
+}
+
+static unsigned pci_read_config32(device_t dev, unsigned where)
+{
+ unsigned addr;
+ addr = dev | where;
+ outl(0x80000000 | (addr & ~3), 0xCF8);
+ return inl(0xCFC);
+}
+
+#include "../../../northbridge/amd/amdk8/reset_test.c"
+
+void hard_reset(void)
+{
+ set_bios_reset();
+ pci_write_config8(PCI_DEV(1, 0x04, 0), 0x47, 1);
+}
+#endif
diff --git a/src/northbridge/amd/gx2/Config.lb b/src/northbridge/amd/gx2/Config.lb
new file mode 100644
index 0000000..4a0c2c8
--- /dev/null
+++ b/src/northbridge/amd/gx2/Config.lb
@@ -0,0 +1,2 @@
+config chip.h
+object northbridge.o
diff --git a/src/northbridge/amd/gx2/chip.h b/src/northbridge/amd/gx2/chip.h
new file mode 100644
index 0000000..4e7ac3c
--- /dev/null
+++ b/src/northbridge/amd/gx2/chip.h
@@ -0,0 +1,5 @@
+struct northbridge_amd_gx2_config
+{
+};
+
+extern struct chip_operations northbridge_amd_gx2_ops;
diff --git a/src/northbridge/amd/gx2/northbridge.c b/src/northbridge/amd/gx2/northbridge.c
new file mode 100644
index 0000000..b02ff78
--- /dev/null
+++ b/src/northbridge/amd/gx2/northbridge.c
@@ -0,0 +1,213 @@
+#include <console/console.h>
+#include <arch/io.h>
+#include <stdint.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <stdlib.h>
+#include <string.h>
+#include <bitops.h>
+#include "chip.h"
+#include "northbridge.h"
+#include <cpu/amd/gx2def.h>
+
+#define NORTHBRIDGE_FILE "northbridge.c"
+/*
+*/
+
+static void optimize_xbus(device_t dev)
+{
+ /* Optimise X-Bus performance */
+ pci_write_config8(dev, 0x40, 0x1e);
+ pci_write_config8(dev, 0x41, 0x52);
+ pci_write_config8(dev, 0x43, 0xc1);
+ pci_write_config8(dev, 0x44, 0x00);
+}
+
+static void enable_shadow(device_t dev)
+{
+
+}
+
+static void northbridge_init(device_t dev)
+{
+ printk_debug("northbridge: %s()\n", __FUNCTION__);
+
+ optimize_xbus(dev);
+ enable_shadow(dev);
+}
+
+
+static struct device_operations northbridge_operations = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = northbridge_init,
+ .enable = 0,
+ .ops_pci = 0,
+};
+
+static struct pci_driver northbridge_driver __pci_driver = {
+ .ops = &northbridge_operations,
+ .vendor = PCI_VENDOR_ID_CYRIX,
+ .device = PCI_DEVICE_ID_CYRIX_PCI_MASTER,
+};
+
+
+
+#define BRIDGE_IO_MASK (IORESOURCE_IO | IORESOURCE_MEM)
+
+static void pci_domain_read_resources(device_t dev)
+{
+ struct resource *resource;
+
+ printk_spew("%s:%s()\n", NORTHBRIDGE_FILE, __FUNCTION__);
+
+ /* Initialize the system wide io space constraints */
+ resource = new_resource(dev, IOINDEX_SUBTRACTIVE(0,0));
+ resource->limit = 0xffffUL;
+ resource->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;
+
+ /* Initialize the system wide memory resources constraints */
+ resource = new_resource(dev, IOINDEX_SUBTRACTIVE(1,0));
+ resource->limit = 0xffffffffULL;
+ resource->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;
+}
+
+static void ram_resource(device_t dev, unsigned long index,
+ unsigned long basek, unsigned long sizek)
+{
+ struct resource *resource;
+
+ if (!sizek) {
+ return;
+ }
+ resource = new_resource(dev, index);
+ resource->base = ((resource_t)basek) << 10;
+ resource->size = ((resource_t)sizek) << 10;
+ resource->flags = IORESOURCE_MEM | IORESOURCE_CACHEABLE | \
+ IORESOURCE_FIXED | IORESOURCE_STORED | IORESOURCE_ASSIGNED;
+}
+
+static void tolm_test(void *gp, struct device *dev, struct resource *new)
+{
+ struct resource **best_p = gp;
+ struct resource *best;
+ best = *best_p;
+ if (!best || (best->base > new->base)) {
+ best = new;
+ }
+ *best_p = best;
+}
+
+static uint32_t find_pci_tolm(struct bus *bus)
+{
+ struct resource *min;
+ uint32_t tolm;
+ min = 0;
+ search_bus_resources(bus, IORESOURCE_MEM, IORESOURCE_MEM, tolm_test, &min);
+ tolm = 0xffffffffUL;
+ if (min && tolm > min->base) {
+ tolm = min->base;
+ }
+ return tolm;
+}
+
+#define FRAMEBUFFERK 4096
+
+static void pci_domain_set_resources(device_t dev)
+{
+ device_t mc_dev;
+ uint32_t pci_tolm;
+
+ pci_tolm = find_pci_tolm(&dev->link[0]);
+ mc_dev = dev->link[0].children;
+ if (mc_dev) {
+ unsigned int tomk, tolmk;
+ unsigned int ramreg = 0;
+ int i, idx;
+ unsigned int *bcdramtop = (unsigned int *)(GX_BASE + BC_DRAM_TOP);
+ unsigned int *mcgbaseadd = (unsigned int *)(GX_BASE + MC_GBASE_ADD);
+
+ for(i=0; i<0x20; i+= 0x10) {
+ unsigned int *mcreg = (unsigned int *)(GX_BASE + MC_BANK_CFG);
+ unsigned int mem_config = *mcreg;
+
+ if (((mem_config & (DIMM_PG_SZ << i)) >> (4 + i)) == 7)
+ continue;
+ ramreg += 1 << (((mem_config & (DIMM_SZ << i)) >> (i + 8)) + 2);
+ }
+
+ tomk = ramreg << 10;
+
+ /* Sort out the framebuffer size */
+ tomk -= FRAMEBUFFERK;
+ *bcdramtop = ((tomk << 10) - 1);
+ *mcgbaseadd = (tomk >> 9);
+
+ printk_debug("BC_DRAM_TOP = 0x%08x\n", *bcdramtop);
+ printk_debug("MC_GBASE_ADD = 0x%08x\n", *mcgbaseadd);
+
+ printk_debug("I would set ram size to %d Mbytes\n", (tomk >> 10));
+
+ /* Compute the top of Low memory */
+ tolmk = pci_tolm >> 10;
+ if (tolmk >= tomk) {
+ /* The PCI hole does does not overlap the memory.
+ */
+ tolmk = tomk;
+ }
+ /* Report the memory regions */
+ idx = 10;
+ ram_resource(dev, idx++, 0, tolmk);
+ }
+ assign_resources(&dev->link[0]);
+}
+
+static unsigned int pci_domain_scan_bus(device_t dev, unsigned int max)
+{
+ max = pci_scan_bus(&dev->link[0], PCI_DEVFN(0, 0), 0xff, max);
+ return max;
+}
+
+static struct device_operations pci_domain_ops = {
+ .read_resources = pci_domain_read_resources,
+ .set_resources = pci_domain_set_resources,
+ .enable_resources = enable_childrens_resources,
+ .init = 0,
+ .scan_bus = pci_domain_scan_bus,
+};
+
+static void cpu_bus_init(device_t dev)
+{
+ initialize_cpus(&dev->link[0]);
+}
+
+static void cpu_bus_noop(device_t dev)
+{
+}
+
+static struct device_operations cpu_bus_ops = {
+ .read_resources = cpu_bus_noop,
+ .set_resources = cpu_bus_noop,
+ .enable_resources = cpu_bus_noop,
+ .init = cpu_bus_init,
+ .scan_bus = 0,
+};
+
+static void enable_dev(struct device *dev)
+{
+ /* Set the operations if it is a special bus type */
+ if (dev->path.type == DEVICE_PATH_PCI_DOMAIN) {
+ dev->ops = &pci_domain_ops;
+ pci_set_method(dev);
+ }
+ else if (dev->path.type == DEVICE_PATH_APIC_CLUSTER) {
+ dev->ops = &cpu_bus_ops;
+ }
+}
+
+struct chip_operations northbridge_amd_gx2_ops = {
+ CHIP_NAME("AMD GX2 Northbridge")
+ .enable_dev = enable_dev,
+};
diff --git a/src/northbridge/amd/gx2/northbridge.h b/src/northbridge/amd/gx2/northbridge.h
new file mode 100644
index 0000000..750ed3b
--- /dev/null
+++ b/src/northbridge/amd/gx2/northbridge.h
@@ -0,0 +1,6 @@
+#ifndef NORTHBRIDGE_AMD_GX2_H
+#define NORTHBRIDGE_AMD_GX2_H
+
+extern unsigned int gx2_scan_root_bus(device_t root, unsigned int max);
+
+#endif /* NORTHBRIDGE_AMD_GX2_H */
diff --git a/src/northbridge/amd/gx2/raminit.c b/src/northbridge/amd/gx2/raminit.c
new file mode 100644
index 0000000..3fc63c6
--- /dev/null
+++ b/src/northbridge/amd/gx2/raminit.c
@@ -0,0 +1,357 @@
+#include <cpu/amd/gx2def.h>
+
+/*
+This software and ancillary information (herein called SOFTWARE )
+called LinuxBIOS is made available under the terms described
+here. The SOFTWARE has been approved for release with associated
+LA-CC Number 00-34 . Unless otherwise indicated, this SOFTWARE has
+been authored by an employee or employees of the University of
+California, operator of the Los Alamos National Laboratory under
+Contract No. W-7405-ENG-36 with the U.S. Department of Energy. The
+U.S. Government has rights to use, reproduce, and distribute this
+SOFTWARE. The public may copy, distribute, prepare derivative works
+and publicly display this SOFTWARE without charge, provided that this
+Notice and any statement of authorship are reproduced on all copies.
+Neither the Government nor the University makes any warranty, express
+or implied, or assumes any liability or responsibility for the use of
+this SOFTWARE. If SOFTWARE is modified to produce derivative works,
+such modified SOFTWARE should be clearly marked, so as not to confuse
+it with the version available from LANL.
+ */
+/* Copyright 2000, Ron Minnich, Advanced Computing Lab, LANL
+ * rminnich@lanl.gov
+ */
+
+/* SDRAM initialization for GX1 - translated from Christer Weinigel's
+ assembler version into C.
+
+ Hamish Guthrie 10/4/2005 hamish@prodigi.ch
+*/
+/* just converted to GX2 by ron minnich -- this is probably mostly wrong
+ * I am just putting in a placeholder to start building gx2 support
+ */
+
+#define NUM_REFRESH 8
+#define TEST_DATA1 0x05A5A5A5A
+#define TEST_DATA2 0x0DEADBEEF
+
+void setGX2Mem(unsigned int addr, unsigned int data)
+{
+ writel(data, (volatile void *)addr);
+}
+
+unsigned int getGX2Mem(unsigned int addr)
+{
+ return (unsigned int)readl((const volatile void *)addr);
+}
+
+void do_refresh(void)
+{
+unsigned int tval, i;
+
+ outb(0x71, 0x80);
+ tval = getGX2Mem(GX_BASE + MC_MEM_CNTRL1);
+ tval |= RFSHTST;
+ for(i=0; i>NUM_REFRESH; i++)
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, tval);
+ outb(0x72, 0x80);
+}
+
+
+void enable_dimm(void)
+{
+unsigned int tval, i;
+
+ outb(0x73, 0x80);
+
+ /* start SDCLCK's */
+ tval = getGX2Mem(GX_BASE + MC_MEM_CNTRL1);
+ tval &= ~SDCLKSTRT;
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, tval);
+ tval |= SDCLKSTRT;
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, tval);
+
+ /* Unmask SDCLK's */
+ tval = getGX2Mem(GX_BASE + MC_MEM_CNTRL2);
+ tval &= ~(SDCLK_MASK | SDCLKOUT_MASK);
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL2, tval);
+ tval = getGX2Mem(GX_BASE + MC_MEM_CNTRL2);
+
+ /* Wait for clocks to unmask */
+ for(i=0; i<5000; i++)
+ outb(0, 0xed);
+
+ /* Refresh memory */
+ tval = getGX2Mem(GX_BASE + MC_MEM_CNTRL1);
+ tval |= RFSHTST;
+ for(i=0; i<NUM_REFRESH; i++)
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, tval);
+ tval &= ~RFSHTST;
+
+ /* Start the SDCLK's */
+ tval &= ~PROGRAM_SDRAM;
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, tval);
+ tval |= PROGRAM_SDRAM | 0x00002000; /* Set refresh timing */
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, tval);
+ tval &= ~PROGRAM_SDRAM;
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, tval);
+
+ /* Refresh memory again */
+ tval = getGX2Mem(GX_BASE + MC_MEM_CNTRL1);
+ tval |= RFSHTST;
+ for(i=0; i>NUM_REFRESH; i++)
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, tval);
+
+ for(i=0; i<2000; i++)
+ outb(0, 0xed);
+ outb(0x74, 0x80);
+}
+
+static unsigned int size_dimm(int dimm_shift)
+{
+int bank_cfg = 0x700; /* MC_BANK_CFG for 512M */
+unsigned int offset = 0x10000000; /* Offset 256M */
+int failed_flag = 1;
+
+ do {
+ setGX2Mem(0, TEST_DATA1);
+ setGX2Mem(offset, TEST_DATA2);
+ setGX2Mem(0x100, 0); /* Clear the bus */
+ if (getGX2Mem(0) != TEST_DATA1) {
+ setGX2Mem(GX_BASE + MC_BANK_CFG,
+ getGX2Mem(GX_BASE + MC_BANK_CFG) & ~(DIMM_SZ << dimm_shift));
+ bank_cfg -= 0x100;
+ setGX2Mem(GX_BASE + MC_BANK_CFG,
+ getGX2Mem(GX_BASE + MC_BANK_CFG) | (bank_cfg << dimm_shift));
+ do_refresh();
+ offset >>= 1;
+ } else {
+ failed_flag = 0;
+ break;
+ }
+ } while (bank_cfg >= 0);
+
+ if (failed_flag)
+ return (0x0070 << dimm_shift);
+ else
+ return(getGX2Mem(GX_BASE + MC_BANK_CFG) & (DIMM_SZ << dimm_shift));
+
+}
+
+static unsigned int module_banks(int dimm_shift)
+{
+int page_size = 0x800; /* Smallest page = 1K * 2 banks */
+int comp_banks;
+
+#if 0
+ print_debug("MC_BANK_CFG = ");
+ print_debug_hex32(getGX2Mem(GX_BASE + MC_BANK_CFG));
+ print_debug("\r\n");
+#endif
+
+ /* retrieve the page size from the MC register */
+ page_size <<= (((getGX2Mem(GX_BASE + MC_BANK_CFG) & (DIMM_PG_SZ << dimm_shift)) >> dimm_shift) >> 4);
+
+#if 0
+ print_debug(" page_size = ");
+ print_debug_hex32(page_size);
+ print_debug("\r\n");
+#endif
+
+ comp_banks = (((getGX2Mem(GX_BASE + MC_BANK_CFG) & (DIMM_COMP_BNK << dimm_shift)) >> dimm_shift) >> 12);
+ page_size <<= comp_banks;
+
+ setGX2Mem(0, TEST_DATA1);
+ setGX2Mem(page_size, TEST_DATA2);
+ setGX2Mem(0x100, 0); /* Clear the bus */
+ if (getGX2Mem(page_size) != TEST_DATA2) {
+ setGX2Mem(GX_BASE + MC_BANK_CFG,
+ getGX2Mem(GX_BASE + MC_BANK_CFG) & ~(DIMM_MOD_BNK << dimm_shift));
+ do_refresh();
+ }
+#if 0
+ print_debug("MC_BANK_CFG = ");
+ print_debug_hex32(getGX2Mem(GX_BASE + MC_BANK_CFG));
+ print_debug("\r\n");
+#endif
+ return(getGX2Mem(GX_BASE + MC_BANK_CFG) & (DIMM_MOD_BNK << dimm_shift));
+}
+
+static unsigned int component_banks(int dimm_shift)
+{
+int page_size = 0x800; /* Smallest page = 1K * 2 banks */
+
+#if 0
+ print_debug("MC_BANK_CFG = ");
+ print_debug_hex32(getGX2Mem(GX_BASE + MC_BANK_CFG));
+ print_debug("\r\n");
+#endif
+
+ page_size = page_size << (((getGX2Mem(GX_BASE + MC_BANK_CFG) & (DIMM_PG_SZ << dimm_shift)) >> dimm_shift) >> 4);
+
+#if 0
+ print_debug(" page_size = ");
+ print_debug_hex32(page_size);
+ print_debug("\r\n");
+#endif
+
+ setGX2Mem(0, TEST_DATA1);
+ setGX2Mem(page_size, TEST_DATA2);
+ setGX2Mem(0x100, 0); /* Clear the bus */
+ if (getGX2Mem(0) != TEST_DATA1) {
+ setGX2Mem(GX_BASE + MC_BANK_CFG,
+ getGX2Mem(GX_BASE + MC_BANK_CFG) & ~(DIMM_COMP_BNK << dimm_shift));
+ do_refresh();
+ }
+#if 0
+ print_debug("MC_BANK_CFG = ");
+ print_debug_hex32(getGX2Mem(GX_BASE + MC_BANK_CFG));
+ print_debug("\r\n");
+#endif
+ return(getGX2Mem(GX_BASE + MC_BANK_CFG) & (DIMM_COMP_BNK << dimm_shift));
+}
+
+static unsigned int page_size(int dimm_shift)
+{
+unsigned int page_test_offset = 0x2000;
+unsigned int temp;
+int page_size_config = 0x40;
+unsigned int probe_config;
+
+ do {
+ setGX2Mem(0, TEST_DATA1);
+ setGX2Mem(page_test_offset, TEST_DATA2);
+ setGX2Mem(0x100, 0);
+ temp = getGX2Mem(0);
+ setGX2Mem(0, 0);
+ if(temp == TEST_DATA1) {
+#if 0
+ print_debug(" Page size Config = ");
+ print_debug_hex32(page_size_config << dimm_shift);
+ print_debug("\r\n");
+#endif
+ return(page_size_config << dimm_shift);
+ }
+
+ temp = ~(DIMM_PG_SZ << dimm_shift);
+
+ probe_config = getGX2Mem(GX_BASE + MC_BANK_CFG);
+ probe_config &= temp;
+
+ page_size_config -= 0x10;
+ page_size_config <<= dimm_shift;
+
+ probe_config |= page_size_config;
+
+ page_size_config >>= dimm_shift;
+
+ page_test_offset >>= 1;
+
+ setGX2Mem(GX_BASE + MC_BANK_CFG, probe_config);
+ do_refresh();
+ } while (page_size_config >= 0);
+
+ return 0x70;
+}
+
+static int dimm_detect(int dimm_shift)
+{
+unsigned int test;
+
+ print_debug("Probing for DIMM");
+ print_debug_char((dimm_shift >> 4) + 0x30);
+ print_debug("\r\n");
+
+ setGX2Mem(0, TEST_DATA1);
+ setGX2Mem(0x100, 0);
+ test = getGX2Mem(0);
+ setGX2Mem(0, 0);
+
+ if (test != TEST_DATA1)
+ return 0;
+
+ print_debug(" Found DIMM");
+ print_debug_char((dimm_shift >> 4) + 0x30);
+ print_debug("\r\n");
+
+ return 1;
+}
+
+static int size_memory(int dimm_shift, unsigned int mem_config)
+{
+
+ if (!dimm_detect(dimm_shift))
+ return (mem_config);
+
+ mem_config &= (~(DIMM_PG_SZ << dimm_shift));
+ mem_config |= (page_size(dimm_shift));
+
+ print_debug(" Page Size: ");
+ print_debug_hex32(0x400 << ((mem_config & (DIMM_PG_SZ << dimm_shift)) >> (dimm_shift + 4)));
+ print_debug("\r\n");
+
+ /* Now do component banks detection */
+
+ mem_config &= (~(DIMM_COMP_BNK << dimm_shift));
+ mem_config |= (component_banks(dimm_shift));
+
+ print_debug(" Component Banks: ");
+ print_debug_char((((mem_config & (DIMM_COMP_BNK << dimm_shift)) >> (dimm_shift + 12)) ? 4 : 2) + 0x30);
+ print_debug("\r\n");
+
+ /* Now do module banks */
+
+ mem_config &= (~(DIMM_MOD_BNK << dimm_shift));
+ mem_config |= (module_banks(dimm_shift));
+
+ print_debug(" Module Banks: ");
+ print_debug_char((((mem_config & (DIMM_MOD_BNK << dimm_shift)) >> (dimm_shift + 14)) ? 2 : 1) + 0x30);
+ print_debug("\r\n");
+
+ mem_config &= (~(DIMM_SZ << dimm_shift));
+ mem_config |= (size_dimm(dimm_shift));
+
+ print_debug(" DIMM size: ");
+ print_debug_hex32(1 <<
+ ((mem_config & (DIMM_SZ << dimm_shift)) >> (dimm_shift + 8)) + 22);
+ print_debug("\r\n");
+
+ return (mem_config);
+}
+
+static void sdram_init(void)
+{
+unsigned int mem_config = 0x00700070;
+
+ print_debug("Setting up default parameters for memory\r\n");
+ outb(0x70, 0x80);
+
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL2, 0x000007d8); /* Disable all CLKS, Shift = 3 */
+ setGX2Mem(GX_BASE + MC_MEM_CNTRL1, 0x92140000); /* MD_DS=2, MA_DS=2, CNTL_DS=2 SDCLKRATE=4 */
+ setGX2Mem(GX_BASE + MC_BANK_CFG, 0x00700070); /* No DIMMS installed */
+ setGX2Mem(GX_BASE + MC_SYNC_TIM1, 0x3a733225); /* LTMODE=3, RC=10, RAS=7, RP=3, RCD=3, RRD=2, DPL=2 */
+ setGX2Mem(GX_BASE + MC_BANK_CFG, 0x57405740); /* Largest DIMM size
+ 0x4000 -- 2 module banks
+ 0x1000 -- 4 component banks
+ 0x0700 -- DIMM size 512MB
+ 0x0040 -- Page Size 16kB */
+
+ enable_dimm();
+
+ print_debug("Sizing memory\r\n");
+
+ setGX2Mem(GX_BASE + MC_BANK_CFG, 0x00705740);
+ do_refresh();
+ mem_config = size_memory(0, mem_config);
+ setGX2Mem(GX_BASE + MC_BANK_CFG, 0x57400070);
+ do_refresh();
+ mem_config = size_memory(16, mem_config);
+
+ print_debug("MC_BANK_CFG = ");
+ print_debug_hex32(mem_config);
+ print_debug("\r\n");
+
+ setGX2Mem(GX_BASE + MC_BANK_CFG, mem_config);
+ enable_dimm();
+ outb(0x7e, 0x80);
+}
diff --git a/src/northbridge/amd/gx2/raminit.h b/src/northbridge/amd/gx2/raminit.h
new file mode 100644
index 0000000..6e40683
--- /dev/null
+++ b/src/northbridge/amd/gx2/raminit.h
@@ -0,0 +1,11 @@
+#ifndef RAMINIT_H
+#define RAMINIT_H
+
+#define DIMM_SOCKETS 4
+struct mem_controller {
+ device_t d0;
+ uint16_t channel0[DIMM_SOCKETS];
+};
+
+
+#endif /* RAMINIT_H */
diff --git a/src/southbridge/amd/cs5535/Config.lb b/src/southbridge/amd/cs5535/Config.lb
new file mode 100644
index 0000000..cc056d9
--- /dev/null
+++ b/src/southbridge/amd/cs5535/Config.lb
@@ -0,0 +1,4 @@
+#config chip.h
+driver cs5535.o
+#driver cs5535_pci.o
+driver cs5535_ide.o
diff --git a/src/southbridge/amd/cs5535/chip.h b/src/southbridge/amd/cs5535/chip.h
new file mode 100644
index 0000000..07a3907
--- /dev/null
+++ b/src/southbridge/amd/cs5535/chip.h
@@ -0,0 +1,12 @@
+#ifndef _SOUTHBRIDGE_AMD_CS5535
+#define _SOUTHBRIDGE_AMD_CS5535
+
+extern struct chip_operations southbridge_amd_cs5535_ops;
+
+struct southbridge_amd_cs5535_config {
+ /* PCI function enables so the pci scan bus finds the devices */
+ int enable_ide;
+ int enable_nvram;
+};
+
+#endif /* _SOUTHBRIDGE_AMD_CS5535 */
diff --git a/src/southbridge/amd/cs5535/cs5530.c b/src/southbridge/amd/cs5535/cs5530.c
new file mode 100644
index 0000000..85028c2
--- /dev/null
+++ b/src/southbridge/amd/cs5535/cs5530.c
@@ -0,0 +1,92 @@
+
+#include <arch/io.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ops.h>
+#include <device/pci_ids.h>
+#include <console/console.h>
+#include "cs5535.h"
+
+static void nvram_on(struct device *dev)
+{
+#if 0
+ volatile char *flash = (volatile unsigned char *)0xFFFc0000;
+ unsigned char id1, id2;
+#endif
+ unsigned char reg;
+
+ /* Enable writes to flash at top of memory */
+ pci_write_config8(dev, 0x52, 0xee);
+
+ /* Set positive decode on ROM */
+ /* Also, there is no apparent reason to turn off the devoce on the */
+ /* IDE devices */
+
+ reg = pci_read_config8(dev, 0x5b);
+ reg |= 1 << 5; /* ROM Decode */
+ reg |= 1 << 3; /* Primary IDE decode */
+ reg |= 1 << 4; /* Secondary IDE decode */
+
+ pci_write_config8(dev, 0x5b, reg);
+
+#if 0 // just to test if the flash is accessible!
+ *(flash + 0x555) = 0xaa;
+ *(flash + 0x2aa) = 0x55;
+ *(flash + 0x555) = 0x90;
+
+ id1 = *(volatile unsigned char *) flash;
+ id2 = *(volatile unsigned char *) (flash + 1);
+
+ *flash = 0xf0;
+
+ printk_debug("Flash device: MFGID %02x, DEVID %02x\n", id1, id2);
+#endif
+}
+
+
+static void southbridge_init(struct device *dev)
+{
+ printk_spew("cs5535: %s\n", __FUNCTION__);
+ nvram_on(dev);
+}
+
+/*
+static void dump_south(struct device *dev)
+{
+ int i, j;
+
+ for(i=0; i<256; i+=16) {
+ printk_debug("0x%02x: ", i);
+ for(j=0; j<16; j++)
+ printk_debug("%02x ", pci_read_config8(dev, i+j));
+ printk_debug("\n");
+ }
+}
+*/
+
+static void southbridge_enable(struct device *dev)
+{
+ printk_spew("%s: dev is %p\n", __FUNCTION__, dev);
+}
+
+static void cs5535_pci_dev_enable_resources(device_t dev)
+{
+ printk_spew("cs5535.c: %s()\n", __FUNCTION__);
+ pci_dev_enable_resources(dev);
+ enable_childrens_resources(dev);
+}
+
+static struct device_operations southbridge_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = cs5535_pci_dev_enable_resources,
+ .init = southbridge_init,
+ .enable = southbridge_enable,
+ .scan_bus = scan_static_bus,
+};
+
+static struct pci_driver cs5535_pci_driver __pci_driver = {
+ .ops = &southbridge_ops,
+ .vendor = PCI_VENDOR_ID_CYRIX,
+ .device = PCI_DEVICE_ID_CYRIX_5535_LEGACY,
+};
diff --git a/src/southbridge/amd/cs5535/cs5530.h b/src/southbridge/amd/cs5535/cs5530.h
new file mode 100644
index 0000000..82d6572
--- /dev/null
+++ b/src/southbridge/amd/cs5535/cs5530.h
@@ -0,0 +1,4 @@
+#ifndef _CS5535_H
+#define _CS5535_H
+
+#endif
diff --git a/src/southbridge/amd/cs5535/cs5530_ide.c b/src/southbridge/amd/cs5535/cs5530_ide.c
new file mode 100644
index 0000000..fc875f9
--- /dev/null
+++ b/src/southbridge/amd/cs5535/cs5530_ide.c
@@ -0,0 +1,30 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "cs5535.h"
+
+static void ide_init(struct device *dev)
+{
+ printk_spew("cs5535_ide: %s\n", __FUNCTION__);
+}
+
+static void ide_enable(struct device *dev)
+{
+ printk_spew("cs5535_ide: %s\n", __FUNCTION__);
+}
+
+static struct device_operations ide_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = ide_init,
+ .enable = ide_enable,
+};
+
+static struct pci_driver ide_driver __pci_driver = {
+ .ops = &ide_ops,
+ .vendor = PCI_VENDOR_ID_AMD,
+ .device = PCI_DEVICE_ID_AMD_5535_IDE,
+};