haswell platforms: restructure romstage main
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
diff --git a/src/mainboard/intel/baskingridge/romstage.c b/src/mainboard/intel/baskingridge/romstage.c
index 2a8e910..9561456 100644
--- a/src/mainboard/intel/baskingridge/romstage.c
+++ b/src/mainboard/intel/baskingridge/romstage.c
@@ -33,7 +33,7 @@
#include "northbridge/intel/haswell/haswell.h"
#include "northbridge/intel/haswell/raminit.h"
#include "southbridge/intel/lynxpoint/pch.h"
-#include "southbridge/intel/lynxpoint/gpio.h"
+#include "southbridge/intel/lynxpoint/me.h"
#include <arch/cpu.h>
#include <cpu/x86/bist.h>
#include <cpu/x86/msr.h>
@@ -42,22 +42,7 @@
#include <vendorcode/google/chromeos/chromeos.h>
#endif
-static void pch_enable_lpc(void)
-{
- device_t dev = PCH_LPC_DEV;
-
- /* Set COM1/COM2 decode range */
- pci_write_config16(dev, LPC_IO_DEC, 0x0010);
-
- /* Enable SuperIO + COM1 + PS/2 Keyboard/Mouse */
- u16 lpc_config = CNF1_LPC_EN | CNF2_LPC_EN | COMA_LPC_EN | KBC_LPC_EN;
- pci_write_config16(dev, LPC_EN, lpc_config);
-}
-
-static void rcba_config(void)
-{
- u32 reg32;
-
+const struct rcba_config_instruction rcba_config[] = {
/*
* GFX INTA -> PIRQA (MSI)
* D28IP_P1IP WLAN INTA -> PIRQB
@@ -71,55 +56,42 @@
*/
/* Device interrupt pin register (board specific) */
- RCBA32(D31IP) = (INTC << D31IP_TTIP) | (NOINT << D31IP_SIP2) |
- (INTB << D31IP_SMIP) | (INTA << D31IP_SIP);
- RCBA32(D30IP) = (NOINT << D30IP_PIP);
- RCBA32(D29IP) = (INTA << D29IP_E1P);
- RCBA32(D28IP) = (INTA << D28IP_P1IP) | (INTC << D28IP_P3IP) |
- (INTB << D28IP_P4IP);
- RCBA32(D27IP) = (INTA << D27IP_ZIP);
- RCBA32(D26IP) = (INTA << D26IP_E2P);
- RCBA32(D25IP) = (NOINT << D25IP_LIP);
- RCBA32(D22IP) = (NOINT << D22IP_MEI1IP);
+ RCBA_SET_REG_32(D31IP, (INTC << D31IP_TTIP) | (NOINT << D31IP_SIP2) |
+ (INTB << D31IP_SMIP) | (INTA << D31IP_SIP)),
+ RCBA_SET_REG_32(D30IP, (NOINT << D30IP_PIP)),
+ RCBA_SET_REG_32(D29IP, (INTA << D29IP_E1P)),
+ RCBA_SET_REG_32(D28IP, (INTA << D28IP_P1IP) | (INTC << D28IP_P3IP) |
+ (INTB << D28IP_P4IP)),
+ RCBA_SET_REG_32(D27IP, (INTA << D27IP_ZIP)),
+ RCBA_SET_REG_32(D26IP, (INTA << D26IP_E2P)),
+ RCBA_SET_REG_32(D25IP, (NOINT << D25IP_LIP)),
+ RCBA_SET_REG_32(D22IP, (NOINT << D22IP_MEI1IP)),
/* Device interrupt route registers */
- DIR_ROUTE(D31IR, PIRQF, PIRQG, PIRQH, PIRQA);
- DIR_ROUTE(D29IR, PIRQD, PIRQE, PIRQF, PIRQG);
- DIR_ROUTE(D28IR, PIRQB, PIRQC, PIRQD, PIRQE);
- DIR_ROUTE(D27IR, PIRQG, PIRQH, PIRQA, PIRQB);
- DIR_ROUTE(D26IR, PIRQE, PIRQF, PIRQG, PIRQH);
- DIR_ROUTE(D25IR, PIRQA, PIRQB, PIRQC, PIRQD);
- DIR_ROUTE(D22IR, PIRQA, PIRQB, PIRQC, PIRQD);
-
- /* Enable IOAPIC (generic) */
- RCBA16(OIC) = 0x0100;
- /* PCH BWG says to read back the IOAPIC enable register */
- (void) RCBA16(OIC);
+ RCBA_SET_REG_32(D31IR, DIR_ROUTE(PIRQF, PIRQG, PIRQH, PIRQA)),
+ RCBA_SET_REG_32(D29IR, DIR_ROUTE(PIRQD, PIRQE, PIRQF, PIRQG)),
+ RCBA_SET_REG_32(D28IR, DIR_ROUTE(PIRQB, PIRQC, PIRQD, PIRQE)),
+ RCBA_SET_REG_32(D27IR, DIR_ROUTE(PIRQG, PIRQH, PIRQA, PIRQB)),
+ RCBA_SET_REG_32(D26IR, DIR_ROUTE(PIRQE, PIRQF, PIRQG, PIRQH)),
+ RCBA_SET_REG_32(D25IR, DIR_ROUTE(PIRQA, PIRQB, PIRQC, PIRQD)),
+ RCBA_SET_REG_32(D22IR, DIR_ROUTE(PIRQA, PIRQB, PIRQC, PIRQD)),
/* Disable unused devices (board specific) */
- reg32 = RCBA32(FD);
- reg32 |= PCH_DISABLE_ALWAYS;
- RCBA32(FD) = reg32;
-}
+ RCBA_RMW_REG_32(FD, ~0, PCH_DISABLE_ALWAYS),
-// FIXME, this function is generic code that should go to sb/... or
-// nb/../early_init.c
-static void early_pch_init(void)
-{
- u8 reg8;
+ /* Enable IOAPIC (generic) */
+ RCBA_SET_REG_16(OIC, 0x0100),
+ /* PCH BWG says to read back the IOAPIC enable register */
+ RCBA_READ_REG_16(OIC),
- // reset rtc power status
- reg8 = pci_read_config8(PCH_LPC_DEV, 0xa4);
- reg8 &= ~(1 << 2);
- pci_write_config8(PCH_LPC_DEV, 0xa4, reg8);
-}
+ RCBA_END_CONFIG,
+};
void main(unsigned long bist)
{
int boot_mode = 0;
+ int wake_from_s3;
int cbmem_was_initted;
- u32 pm1_cnt;
- u16 pm1_sts;
#if CONFIG_COLLECT_TIMESTAMPS
tsc_t start_romstage_time;
@@ -180,64 +152,26 @@
if (bist == 0)
enable_lapic();
- pch_enable_lpc();
-
- /* Enable GPIOs */
- pci_write_config32(PCH_LPC_DEV, GPIO_BASE, DEFAULT_GPIOBASE|1);
- pci_write_config8(PCH_LPC_DEV, GPIO_CNTL, 0x10);
- setup_pch_gpios(&mainboard_gpio_map);
-
- /* Early Console setup */
- console_init();
+ wake_from_s3 = early_pch_init(&mainboard_gpio_map, &rcba_config[0]);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
- /*
- * FIXME: MCHBAR isn't setup yet. It's setup in
- * haswell_early_initialization().
- */
- if (MCHBAR16(SSKPD) == 0xCAFE) {
- printk(BIOS_DEBUG, "soft reset detected\n");
- boot_mode = 1;
-
- /* System is not happy after keyboard reset... */
- printk(BIOS_DEBUG, "Issuing CF9 warm reset\n");
- outb(0x6, 0xcf9);
- while (1) {
- hlt();
- }
- }
-
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
haswell_early_initialization(HASWELL_MOBILE);
printk(BIOS_DEBUG, "Back from haswell_early_initialization()\n");
- /* Check PM1_STS[15] to see if we are waking from Sx */
- pm1_sts = inw(DEFAULT_PMBASE + PM1_STS);
-
- /* Read PM1_CNT[12:10] to determine which Sx state */
- pm1_cnt = inl(DEFAULT_PMBASE + PM1_CNT);
-
- if ((pm1_sts & WAK_STS) && ((pm1_cnt >> 10) & 7) == 5) {
+ if (wake_from_s3) {
#if CONFIG_HAVE_ACPI_RESUME
printk(BIOS_DEBUG, "Resume from S3 detected.\n");
boot_mode = 2;
- /* Clear SLP_TYPE. This will break stage2 but
- * we care for that when we get there.
- */
- outl(pm1_cnt & ~(7 << 10), DEFAULT_PMBASE + PM1_CNT);
#else
printk(BIOS_DEBUG, "Resume from S3 detected, but disabled.\n");
#endif
}
- post_code(0x38);
- /* Enable SPD ROMs and DDR-III DRAM */
- enable_smbus();
-
/* Prepare USB controller early in S3 resume */
if (boot_mode == 2)
enable_usb_bar();
@@ -247,21 +181,17 @@
#if CONFIG_COLLECT_TIMESTAMPS
before_dram_time = rdtsc();
#endif
+
+ report_platform_info();
+
sdram_initialize(&pei_data);
#if CONFIG_COLLECT_TIMESTAMPS
after_dram_time = rdtsc();
#endif
post_code(0x3b);
- /* Perform some initialization that must run before stage2 */
- early_pch_init();
- post_code(0x3c);
- /* This should probably go away. Until now it is required
- * and mainboard specific
- */
- rcba_config();
- post_code(0x3d);
+ intel_early_me_status();
quick_ram_check();
post_code(0x3e);
diff --git a/src/northbridge/intel/haswell/early_init.c b/src/northbridge/intel/haswell/early_init.c
index 505fbf1..681af42 100644
--- a/src/northbridge/intel/haswell/early_init.c
+++ b/src/northbridge/intel/haswell/early_init.c
@@ -29,20 +29,6 @@
static void haswell_setup_bars(void)
{
- /* Setting up Southbridge. In the northbridge code. */
- printk(BIOS_DEBUG, "Setting up static southbridge registers...");
- pci_write_config32(PCI_DEV(0, 0x1f, 0), RCBA, DEFAULT_RCBA | 1);
-
- pci_write_config32(PCI_DEV(0, 0x1f, 0), PMBASE, DEFAULT_PMBASE | 1);
- pci_write_config8(PCI_DEV(0, 0x1f, 0), 0x44 /* ACPI_CNTL */ , 0x80); /* Enable ACPI BAR */
-
- printk(BIOS_DEBUG, " done.\n");
-
- printk(BIOS_DEBUG, "Disabling Watchdog reboot...");
- RCBA32(GCS) = RCBA32(GCS) | (1 << 5); /* No reset */
- outw((1 << 11), DEFAULT_PMBASE | 0x60 | 0x08); /* halt timer */
- printk(BIOS_DEBUG, " done.\n");
-
printk(BIOS_DEBUG, "Setting up static northbridge registers...");
/* Set up all hardcoded northbridge BARs */
pci_write_config32(PCI_DEV(0, 0x00, 0), EPBAR, DEFAULT_EPBAR | 1);
@@ -62,14 +48,6 @@
pci_write_config8(PCI_DEV(0, 0x00, 0), PAM6, 0x33);
printk(BIOS_DEBUG, " done.\n");
-
-#if CONFIG_ELOG_BOOT_COUNT
- /* Increment Boot Counter except when resuming from S3 */
- if ((inw(DEFAULT_PMBASE + PM1_STS) & WAK_STS) &&
- ((inl(DEFAULT_PMBASE + PM1_CNT) >> 10) & 7) == SLP_TYP_S3)
- return;
- boot_count_increment();
-#endif
}
static void haswell_setup_graphics(void)
diff --git a/src/northbridge/intel/haswell/raminit.c b/src/northbridge/intel/haswell/raminit.c
index 0c68e60..e2b085b 100644
--- a/src/northbridge/intel/haswell/raminit.c
+++ b/src/northbridge/intel/haswell/raminit.c
@@ -32,8 +32,6 @@
#include "pei_data.h"
#include "haswell.h"
-/* Management Engine is in the southbridge */
-#include "southbridge/intel/lynxpoint/me.h"
#if CONFIG_CHROMEOS
#include <vendorcode/google/chromeos/chromeos.h>
#else
@@ -152,12 +150,6 @@
struct sys_info sysinfo;
unsigned long entry;
- report_platform_info();
-
- /* Wait for ME to be ready */
- intel_early_me_init();
- intel_early_me_uma_size();
-
printk(BIOS_DEBUG, "Starting UEFI PEI System Agent\n");
memset(&sysinfo, 0, sizeof(sysinfo));
@@ -216,8 +208,6 @@
version >> 24 , (version >> 16) & 0xff,
(version >> 8) & 0xff, version & 0xff);
- intel_early_me_status();
-
report_memory_config();
/* S3 resume: don't save scrambler seed or MRC data */
@@ -232,7 +222,10 @@
unsigned long get_top_of_ram(void)
{
- /* Base of TSEG is top of usable DRAM */
+ /*
+ * Base of TSEG is top of usable DRAM below 4GiB. The register has
+ * 1 MiB alignement.
+ */
u32 tom = pci_read_config32(PCI_DEV(0,0,0), TSEG);
- return (unsigned long) tom;
+ return (unsigned long) tom & ~((1 << 20) - 1);
}
diff --git a/src/southbridge/intel/lynxpoint/Makefile.inc b/src/southbridge/intel/lynxpoint/Makefile.inc
index c14a538..6e84ce6 100644
--- a/src/southbridge/intel/lynxpoint/Makefile.inc
+++ b/src/southbridge/intel/lynxpoint/Makefile.inc
@@ -45,7 +45,7 @@
ramstage-$(CONFIG_HAVE_SMI_HANDLER) += smi.c
smm-$(CONFIG_HAVE_SMI_HANDLER) += smihandler.c me_9.x.c finalize.c
-romstage-y += early_usb.c early_smbus.c early_me.c me_status.c
+romstage-y += early_usb.c early_smbus.c early_me.c me_status.c early_pch.c
romstage-$(CONFIG_USBDEBUG) += usb_debug.c
romstage-y += reset.c early_spi.c
diff --git a/src/southbridge/intel/lynxpoint/early_pch.c b/src/southbridge/intel/lynxpoint/early_pch.c
new file mode 100644
index 0000000..d0a583f
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/early_pch.c
@@ -0,0 +1,172 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2012 Google Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+
+#include <console/console.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <device/pci_def.h>
+#include <elog.h>
+#include "pch.h"
+
+#if CONFIG_INTEL_LYNXPOINT_LP
+#include "lp_gpio.h"
+#else
+#include "gpio.h"
+#endif
+
+static void pch_enable_bars(void)
+{
+ /* Setting up Southbridge. In the northbridge code. */
+ pci_write_config32(PCH_LPC_DEV, RCBA, DEFAULT_RCBA | 1);
+
+ pci_write_config32(PCH_LPC_DEV, PMBASE, DEFAULT_PMBASE | 1);
+ /* Enable ACPI BAR */
+ pci_write_config8(PCH_LPC_DEV, ACPI_CNTL, 0x80);
+
+ pci_write_config32(PCH_LPC_DEV, GPIO_BASE, DEFAULT_GPIOBASE|1);
+
+ /* Enable GPIO functionality. */
+ pci_write_config8(PCH_LPC_DEV, GPIO_CNTL, 0x10);
+}
+
+static void pch_generic_setup(void)
+{
+ u8 reg8;
+
+ printk(BIOS_DEBUG, "Disabling Watchdog reboot...");
+ RCBA32(GCS) = RCBA32(GCS) | (1 << 5); /* No reset */
+ outw((1 << 11), DEFAULT_PMBASE | 0x60 | 0x08); /* halt timer */
+ printk(BIOS_DEBUG, " done.\n");
+
+ // reset rtc power status
+ reg8 = pci_read_config8(PCH_LPC_DEV, GEN_PMCON_3);
+ reg8 &= ~(1 << 2);
+ pci_write_config8(PCH_LPC_DEV, GEN_PMCON_3, reg8);
+}
+
+static int sleep_type_s3(void)
+{
+ u32 pm1_cnt;
+ u16 pm1_sts;
+ int is_s3 = 0;
+
+ /* Check PM1_STS[15] to see if we are waking from Sx */
+ pm1_sts = inw(DEFAULT_PMBASE + PM1_STS);
+ if (pm1_sts & WAK_STS) {
+ /* Read PM1_CNT[12:10] to determine which Sx state */
+ pm1_cnt = inl(DEFAULT_PMBASE + PM1_CNT);
+ if (((pm1_cnt >> 10) & 7) == SLP_TYP_S3) {
+ /* Clear SLP_TYPE. */
+ outl(pm1_cnt & ~(7 << 10), DEFAULT_PMBASE + PM1_CNT);
+ is_s3 = 1;
+ }
+ }
+ return is_s3;
+}
+
+static void pch_enable_lpc(void)
+{
+ device_t dev = PCH_LPC_DEV;
+
+ /* Set COM1/COM2 decode range */
+ pci_write_config16(dev, LPC_IO_DEC, 0x0010);
+
+ /* Enable SuperIO + COM1 + PS/2 Keyboard/Mouse */
+ u16 lpc_config = CNF1_LPC_EN | CNF2_LPC_EN | COMA_LPC_EN | KBC_LPC_EN;
+ pci_write_config16(dev, LPC_EN, lpc_config);
+}
+
+static void pch_config_rcba(const struct rcba_config_instruction *rcba_config)
+{
+ const struct rcba_config_instruction *rc;
+ u32 value;
+
+ rc = rcba_config;
+ while (rc->command != RCBA_COMMAND_END)
+ {
+ if ((rc->command & RCBA_REG_SIZE_MASK) == RCBA_REG_SIZE_16) {
+ switch (rc->command & RCBA_COMMAND_MASK) {
+ case RCBA_COMMAND_SET:
+ RCBA16(rc->reg) = (u16)rc->or_value;
+ break;
+ case RCBA_COMMAND_READ:
+ (void)RCBA16(rc->reg);
+ break;
+ case RCBA_COMMAND_RMW:
+ value = RCBA16(rc->reg);
+ value &= rc->mask;
+ value |= rc->or_value;
+ RCBA16(rc->reg) = (u16)value;
+ break;
+ }
+ } else {
+ switch (rc->command & RCBA_COMMAND_MASK) {
+ case RCBA_COMMAND_SET:
+ RCBA32(rc->reg) = rc->or_value;
+ break;
+ case RCBA_COMMAND_READ:
+ (void)RCBA32(rc->reg);
+ break;
+ case RCBA_COMMAND_RMW:
+ value = RCBA32(rc->reg);
+ value &= rc->mask;
+ value |= rc->or_value;
+ RCBA32(rc->reg) = value;
+ break;
+ }
+ }
+ rc++;
+ }
+}
+
+int early_pch_init(const void *gpio_map,
+ const struct rcba_config_instruction *rcba_config)
+{
+ int wake_from_s3;
+
+ pch_enable_lpc();
+
+ pch_enable_bars();
+
+#if CONFIG_INTEL_LYNXPOINT_LP
+ setup_pch_lp_gpios(gpio_map);
+#else
+ setup_pch_gpios(gpio_map);
+#endif
+
+ console_init();
+
+ pch_generic_setup();
+
+ /* Enable SMBus for reading SPDs. */
+ enable_smbus();
+
+ pch_config_rcba(rcba_config);
+
+ wake_from_s3 = sleep_type_s3();
+
+#if CONFIG_ELOG_BOOT_COUNT
+ if (!wake_from_s3)
+ boot_count_increment();
+#endif
+
+ /* Report if we are waking from s3. */
+ return wake_from_s3;
+}
diff --git a/src/southbridge/intel/lynxpoint/pch.h b/src/southbridge/intel/lynxpoint/pch.h
index f265448..f27ae90 100644
--- a/src/southbridge/intel/lynxpoint/pch.h
+++ b/src/southbridge/intel/lynxpoint/pch.h
@@ -102,6 +102,48 @@
void enable_usb_bar(void);
int smbus_read_byte(unsigned device, unsigned address);
int early_spi_read(u32 offset, u32 size, u8 *buffer);
+
+/* State Machine configuration. */
+#define RCBA_REG_SIZE_MASK 0x8000
+#define RCBA_REG_SIZE_16 0x8000
+#define RCBA_REG_SIZE_32 0x0000
+#define RCBA_COMMAND_MASK 0x000f
+#define RCBA_COMMAND_SET 0x0001
+#define RCBA_COMMAND_READ 0x0002
+#define RCBA_COMMAND_RMW 0x0003
+#define RCBA_COMMAND_END 0x0007
+
+#define RCBA_ENCODE_COMMAND(command_, reg_, mask_, or_value_) \
+ { .command = command_, \
+ .reg = reg_, \
+ .mask = mask_, \
+ .or_value = or_value_ \
+ }
+#define RCBA_SET_REG_32(reg_, value_) \
+ RCBA_ENCODE_COMMAND(RCBA_REG_SIZE_32|RCBA_COMMAND_SET, reg_, 0, value_)
+#define RCBA_READ_REG_32(reg_) \
+ RCBA_ENCODE_COMMAND(RCBA_REG_SIZE_32|RCBA_COMMAND_READ, reg_, 0, 0)
+#define RCBA_RMW_REG_32(reg_, mask_, or_) \
+ RCBA_ENCODE_COMMAND(RCBA_REG_SIZE_32|RCBA_COMMAND_RMW, reg_, mask_, or_)
+#define RCBA_SET_REG_16(reg_, value_) \
+ RCBA_ENCODE_COMMAND(RCBA_REG_SIZE_16|RCBA_COMMAND_SET, reg_, 0, value_)
+#define RCBA_READ_REG_16(reg_) \
+ RCBA_ENCODE_COMMAND(RCBA_REG_SIZE_16|RCBA_COMMAND_READ, reg_, 0, 0)
+#define RCBA_RMW_REG_16(reg_, mask_, or_) \
+ RCBA_ENCODE_COMMAND(RCBA_REG_SIZE_16|RCBA_COMMAND_RMW, reg_, mask_, or_)
+#define RCBA_END_CONFIG \
+ RCBA_ENCODE_COMMAND(RCBA_COMMAND_END, 0, 0, 0)
+
+struct rcba_config_instruction
+{
+ u16 command;
+ u16 reg;
+ u32 mask;
+ u32 or_value;
+};
+
+int early_pch_init(const void *gpio_map,
+ const struct rcba_config_instruction *rcba_config);
#endif
/*
* get GPIO pin value
@@ -460,9 +502,9 @@
#define SOFT_RESET_CTRL 0x38f4
#define SOFT_RESET_DATA 0x38f8
-#define DIR_ROUTE(x,a,b,c,d) \
- RCBA32(x) = (((d) << DIR_IDR) | ((c) << DIR_ICR) | \
- ((b) << DIR_IBR) | ((a) << DIR_IAR))
+#define DIR_ROUTE(a,b,c,d) \
+ (((d) << DIR_IDR) | ((c) << DIR_ICR) | \
+ ((b) << DIR_IBR) | ((a) << DIR_IAR))
#define RC 0x3400 /* 32bit */
#define HPTC 0x3404 /* 32bit */