chip soc/amd/genoa

	# USB configuration
	register "usb.xhci0_enable" = "1"
	register "usb.xhci1_enable" = "1"
	# OC pins
	register "usb.usb2_oc_pins[0].port0" = "0x0"
	register "usb.usb2_oc_pins[0].port1" = "0x1"
	register "usb.usb2_oc_pins[0].port2" = "0x0"
	register "usb.usb2_oc_pins[0].port3" = "0x1"

	register "usb.usb2_oc_pins[1].port0" = "0x0"
	register "usb.usb2_oc_pins[1].port1" = "0x1"

	register "usb.usb3_oc_pins[0].port0" = "0x0"
	register "usb.usb3_oc_pins[0].port1" = "0x1"
	register "usb.usb3_oc_pins[0].port2" = "0x0"
	register "usb.usb3_oc_pins[0].port3" = "0x1"
	register "usb.usb3_oc_pins[1].port0" = "0x0"
	register "usb.usb3_oc_pins[1].port1" = "0x1"

	register "usb.polarity_cfg_low" = "true"

	register "usb.usb3_force_gen1.port0" = "3"
	register "usb.usb3_force_gen1.port1" = "3"
	register "usb.usb3_force_gen1.port2" = "3"
	register "usb.usb3_force_gen1.port3" = "3"

	# eSPI configuration
	register "common_config.espi_config" = "{
		.std_io_decode_bitmap = ESPI_DECODE_IO_0x80_EN,
		.io_mode = ESPI_IO_MODE_SINGLE,
		.op_freq_mhz = ESPI_OP_FREQ_33_MHZ,
		.crc_check_enable = 1,
		.alert_pin = ESPI_ALERT_PIN_PUSH_PULL,
		.periph_ch_en = 0,
		.vw_ch_en = 0,
		.oob_ch_en = 0,
		.flash_ch_en = 0,
	}"

	# PHY settings
	register "usb.usb31_phy_enable" = "1"
	register "usb.usb31_phy" = "{
			{0x01, 0x07, 0x00, 0x00, 0x07, 0x01, 0x05, 0x00, 0x05, 0x00, 0x05, 0x00},
			{0x05, 0x07, 0x00, 0x00, 0x07, 0x01, 0x05, 0x00, 0x05, 0x00, 0x05, 0x00},
			{0x05, 0x07, 0x00, 0x00, 0x07, 0x01, 0x05, 0x00, 0x05, 0x00, 0x05, 0x00},
			{0x05, 0x07, 0x00, 0x00, 0x07, 0x01, 0x05, 0x00, 0x05, 0x00, 0x05, 0x00},
			{0x05, 0x01, 0x07, 0x00, 0x00, 0x07, 0x01, 0x05, 0x00, 0x05, 0x00, 0x05},
			{0x00, 0x05, 0x07, 0x00, 0x00, 0x07, 0x01, 0x05, 0x00, 0x05, 0x00, 0x05},
			{0x00, 0x05, 0x07, 0x00, 0x00, 0x07, 0x01, 0x05, 0x00, 0x05, 0x00, 0x05},
			{0x00, 0x05, 0x07, 0x00, 0x00, 0x07, 0x01, 0x05, 0x00, 0x05, 0x00, 0x05},
		}"

	device domain 0 on
	end

end