soc/intel/baytrail: Get rid of device_t
Use of device_t has been abandoned in ramstage.
Change-Id: I8b2cfe3e2090fb8eed755e40d337c6049d8dd96e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
diff --git a/src/soc/intel/baytrail/southcluster.c b/src/soc/intel/baytrail/southcluster.c
index 84ae0ee..8dd8986 100644
--- a/src/soc/intel/baytrail/southcluster.c
+++ b/src/soc/intel/baytrail/southcluster.c
@@ -42,12 +42,13 @@
#include <cpu/cpu.h>
static inline void
-add_mmio_resource(device_t dev, int i, unsigned long addr, unsigned long size)
+add_mmio_resource(struct device *dev, int i, unsigned long addr,
+ unsigned long size)
{
mmio_resource(dev, i, addr >> 10, size >> 10);
}
-static void sc_add_mmio_resources(device_t dev)
+static void sc_add_mmio_resources(struct device *dev)
{
add_mmio_resource(dev, 0xfeb, ABORT_BASE_ADDRESS, ABORT_BASE_SIZE);
add_mmio_resource(dev, PBASE, PMC_BASE_ADDRESS, PMC_BASE_SIZE);
@@ -82,7 +83,8 @@
* Note: this function assumes there is no overlap with the default LPC device's
* claimed range: LPC_DEFAULT_IO_RANGE_LOWER -> LPC_DEFAULT_IO_RANGE_UPPER.
*/
-static void sc_add_io_resource(device_t dev, int base, int size, int index)
+static void sc_add_io_resource(struct device *dev, int base, int size,
+ int index)
{
struct resource *res;
@@ -95,7 +97,7 @@
res->flags = IORESOURCE_IO | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
}
-static void sc_add_io_resources(device_t dev)
+static void sc_add_io_resources(struct device *dev)
{
struct resource *res;
@@ -112,7 +114,7 @@
sc_add_io_resource(dev, ACPI_BASE_ADDRESS, 128, ABASE);
}
-static void sc_read_resources(device_t dev)
+static void sc_read_resources(struct device *dev)
{
/* Get the normal PCI resources of this device. */
pci_dev_read_resources(dev);
@@ -137,7 +139,7 @@
* or configuration. This is definitely a hack, but it helps the kernel
* along.
*/
-static void com1_configure_resume(device_t dev)
+static void com1_configure_resume(struct device *dev)
{
const uint16_t port = 0x3f8;
@@ -165,7 +167,7 @@
outb(3, port + UART8250_LCR);
}
-static void sc_init(device_t dev)
+static void sc_init(struct device *dev)
{
int i;
u8 *pr_base = (u8 *)(ILB_BASE_ADDRESS + 0x08);
@@ -207,7 +209,7 @@
*/
/* Set bit in function disable register to hide this device. */
-static void sc_disable_devfn(device_t dev)
+static void sc_disable_devfn(struct device *dev)
{
u32 *func_dis = (u32 *)(PMC_BASE_ADDRESS + FUNC_DIS);
u32 *func_dis2 = (u32 *)(PMC_BASE_ADDRESS + FUNC_DIS2);
@@ -316,7 +318,7 @@
}
}
-static inline void set_d3hot_bits(device_t dev, int offset)
+static inline void set_d3hot_bits(struct device *dev, int offset)
{
uint32_t reg8;
printk(BIOS_DEBUG, "Power management CAP offset 0x%x.\n", offset);
@@ -328,7 +330,7 @@
/* Parts of the audio subsystem are powered by the HDA device. Therefore, one
* cannot put HDA into D3Hot. Instead perform this workaround to make some of
* the audio paths work for LPE audio. */
-static void hda_work_around(device_t dev)
+static void hda_work_around(struct device *dev)
{
u32 *gctl = (u32 *)(TEMP_BASE_ADDRESS + 0x8);
@@ -345,7 +347,7 @@
pci_write_config32(dev, PCI_BASE_ADDRESS_0, 0);
}
-static int place_device_in_d3hot(device_t dev)
+static int place_device_in_d3hot(struct device *dev)
{
unsigned offset;
@@ -461,7 +463,7 @@
}
/* Common PCI device function disable. */
-void southcluster_enable_dev(device_t dev)
+void southcluster_enable_dev(struct device *dev)
{
uint32_t reg32;
@@ -494,7 +496,7 @@
}
}
-static void southcluster_inject_dsdt(device_t device)
+static void southcluster_inject_dsdt(struct device *device)
{
global_nvs_t *gnvs;