| uses HAVE_MP_TABLE |
| uses HAVE_PIRQ_TABLE |
| uses USE_FALLBACK_IMAGE |
| uses HAVE_FALLBACK_BOOT |
| uses HAVE_HARD_RESET |
| uses HAVE_OPTION_TABLE |
| uses USE_OPTION_TABLE |
| uses CONFIG_ROM_PAYLOAD |
| uses IRQ_SLOT_COUNT |
| uses MAINBOARD |
| uses MAINBOARD_VENDOR |
| uses MAINBOARD_PART_NUMBER |
| uses LINUXBIOS_EXTRA_VERSION |
| uses ARCH |
| uses FALLBACK_SIZE |
| uses STACK_SIZE |
| uses HEAP_SIZE |
| uses ROM_SIZE |
| uses ROM_SECTION_SIZE |
| uses ROM_IMAGE_SIZE |
| uses ROM_SECTION_SIZE |
| uses ROM_SECTION_OFFSET |
| uses CONFIG_ROM_PAYLOAD_START |
| uses CONFIG_COMPRESSED_PAYLOAD_NRV2B |
| uses CONFIG_COMPRESSED_PAYLOAD_LZMA |
| uses CONFIG_PRECOMPRESSED_PAYLOAD |
| uses PAYLOAD_SIZE |
| uses _ROMBASE |
| uses _RAMBASE |
| uses XIP_ROM_SIZE |
| uses XIP_ROM_BASE |
| uses HAVE_MP_TABLE |
| uses HAVE_ACPI_TABLES |
| uses CROSS_COMPILE |
| uses CC |
| uses HOSTCC |
| uses OBJCOPY |
| uses DEFAULT_CONSOLE_LOGLEVEL |
| uses MAXIMUM_CONSOLE_LOGLEVEL |
| uses CONFIG_CONSOLE_SERIAL8250 |
| uses CONFIG_UDELAY_TSC |
| uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 |
| uses CONFIG_PCI_ROM_RUN |
| uses CONFIG_CONSOLE_VGA |
| uses CONFIG_MAX_PCI_BUSES |
| uses TTYS0_BAUD |
| |
| ## ROM_SIZE is the size of boot ROM that this board will use. |
| default ROM_SIZE = 256*1024 |
| |
| ### |
| ### Build options |
| ### |
| default CONFIG_PCI_ROM_RUN=0 |
| default CONFIG_CONSOLE_VGA=0 |
| |
| ## |
| ## Build code for the fallback boot |
| ## |
| default HAVE_FALLBACK_BOOT=1 |
| |
| ## |
| ## no MP table |
| ## |
| default HAVE_MP_TABLE=0 |
| |
| ## |
| ## Use TSC for udelay. |
| ## |
| default CONFIG_UDELAY_TSC=1 |
| default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 |
| |
| ## |
| ## Build code to reset the motherboard from linuxBIOS |
| ## |
| default HAVE_HARD_RESET=0 |
| |
| ## |
| ## Build code to export a programmable irq routing table |
| ## |
| default HAVE_PIRQ_TABLE=1 |
| default IRQ_SLOT_COUNT=5 |
| |
| |
| ## |
| ## Build code to load acpi tables |
| ## |
| default HAVE_ACPI_TABLES=1 |
| |
| |
| ## |
| ## Build code to export a CMOS option table |
| ## |
| default HAVE_OPTION_TABLE=1 |
| |
| ### |
| ### LinuxBIOS layout values |
| ### |
| |
| ## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. |
| default ROM_IMAGE_SIZE = 65536 |
| default FALLBACK_SIZE = 131072 |
| |
| ## |
| ## Use a small 8K stack |
| ## |
| default STACK_SIZE=0x2000 |
| |
| ## |
| ## Use a small 16K heap |
| ## |
| default HEAP_SIZE=0x4000 |
| |
| ## |
| ## Only use the option table in a normal image |
| ## |
| #default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE |
| default USE_OPTION_TABLE = 0 |
| |
| default _RAMBASE = 0x00004000 |
| |
| default CONFIG_ROM_PAYLOAD = 1 |
| |
| ## |
| ## The default compiler |
| ## |
| default CROSS_COMPILE="" |
| default CC="$(CROSS_COMPILE)gcc -m32" |
| default HOSTCC="gcc" |
| |
| ## |
| ## Set this to the max PCI bus number you |
| ## would ever use for PCI config IO. |
| ## Setting this number very high will make |
| ## pci_locate_device take a long time when |
| ## it can't find a device. |
| ## |
| default CONFIG_MAX_PCI_BUSES = 5 |
| |
| end |
| |