Add support for E7505 northbridge.
Adapted from northbridge/intel/e7501 with only minor changes.
This commit provides minimal patch from e7501 and I prefer any
cosmetic clean-up to be done after initial merge.
Due the incomplete register specifications, it is safer to have
e7505 as a separate directory in case I improve it to support
wider range of memory configurations. I have no e7501 to test with.
Change-Id: Iba3bf9d69ff5e9d9ef3a6ebf8259f048c55d637d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/295
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
diff --git a/src/northbridge/intel/e7505/Kconfig b/src/northbridge/intel/e7505/Kconfig
index c8219e8..578ab86 100644
--- a/src/northbridge/intel/e7505/Kconfig
+++ b/src/northbridge/intel/e7505/Kconfig
@@ -1,4 +1,4 @@
-config NORTHBRIDGE_INTEL_E7501
+config NORTHBRIDGE_INTEL_E7505
bool
select HAVE_DEBUG_RAM_SETUP
diff --git a/src/northbridge/intel/e7505/chip.h b/src/northbridge/intel/e7505/chip.h
index 458510b..9677dca 100644
--- a/src/northbridge/intel/e7505/chip.h
+++ b/src/northbridge/intel/e7505/chip.h
@@ -1,5 +1,6 @@
-struct northbridge_intel_e7501_config
+struct northbridge_intel_e7505_config
{
};
-extern struct chip_operations northbridge_intel_e7501_ops;
+extern struct chip_operations northbridge_intel_e7505_ops;
+
diff --git a/src/northbridge/intel/e7505/debug.c b/src/northbridge/intel/e7505/debug.c
index f19de0c..07f1596 100644
--- a/src/northbridge/intel/e7505/debug.c
+++ b/src/northbridge/intel/e7505/debug.c
@@ -39,7 +39,7 @@
for(i = 0; i < 256; i++) {
unsigned char val;
if ((i & 0x0f) == 0) {
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "\n%02x:",i);
#else
print_debug("\n");
@@ -48,7 +48,7 @@
#endif
}
val = pci_read_config8(dev, i);
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, " %02x", val);
#else
print_debug_char(' ');
@@ -101,7 +101,7 @@
device = ctrl->channel0[i];
if (device) {
int j;
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "dimm: %02x.0: %02x", i, device);
#else
print_debug("dimm: ");
@@ -113,7 +113,7 @@
int status;
unsigned char byte;
if ((j & 0xf) == 0) {
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "\n%02x: ", j);
#else
print_debug("\n");
@@ -126,7 +126,7 @@
break;
}
byte = status & 0xff;
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "%02x ", byte);
#else
print_debug_hex8(byte);
@@ -138,7 +138,7 @@
device = ctrl->channel1[i];
if (device) {
int j;
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "dimm: %02x.1: %02x", i, device);
#else
print_debug("dimm: ");
@@ -150,7 +150,7 @@
int status;
unsigned char byte;
if ((j & 0xf) == 0) {
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "\n%02x: ", j);
#else
print_debug("\n");
@@ -163,7 +163,7 @@
break;
}
byte = status & 0xff;
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "%02x ", byte);
#else
print_debug_hex8(byte);
@@ -181,7 +181,7 @@
for(device = 1; device < 0x80; device++) {
int j;
if( smbus_read_byte(device, 0) < 0 ) continue;
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "smbus: %02x", device);
#else
print_debug("smbus: ");
@@ -195,7 +195,7 @@
break;
}
if ((j & 0xf) == 0) {
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "\n%02x: ",j);
#else
print_debug("\n");
@@ -204,7 +204,7 @@
#endif
}
byte = status & 0xff;
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "%02x ", byte);
#else
print_debug_hex8(byte);
@@ -219,7 +219,7 @@
{
int i;
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "%04x:\n", port);
#else
print_debug_hex16(port);
@@ -228,7 +228,7 @@
for(i=0;i<256;i++) {
uint8_t val;
if ((i & 0x0f) == 0) {
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "%02x:", i);
#else
print_debug_hex8(i);
@@ -236,7 +236,7 @@
#endif
}
val = inb(port);
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, " %02x",val);
#else
print_debug_char(' ');
@@ -255,7 +255,7 @@
print_debug("dump_mem:");
for(i=start;i<end;i++) {
if((i & 0xf)==0) {
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, "\n%08x:", i);
#else
print_debug("\n");
@@ -263,7 +263,7 @@
print_debug(":");
#endif
}
-#if CONFIG_CACHE_AS_RAM
+#if !defined(__ROMCC__)
printk(BIOS_DEBUG, " %02x", (unsigned char)*((unsigned char *)i));
#else
print_debug(" ");
diff --git a/src/northbridge/intel/e7505/e7501.h b/src/northbridge/intel/e7505/e7505.h
similarity index 97%
rename from src/northbridge/intel/e7505/e7501.h
rename to src/northbridge/intel/e7505/e7505.h
index 32a26da..e20c5bc 100644
--- a/src/northbridge/intel/e7505/e7501.h
+++ b/src/northbridge/intel/e7505/e7505.h
@@ -19,7 +19,7 @@
*/
/*
- * e7501.h: PCI configuration space for the Intel E7501 memory controller
+ * e7505.h: PCI configuration space for the Intel E7501 memory controller
*/
/************ D0:F0 ************/
diff --git a/src/northbridge/intel/e7505/northbridge.c b/src/northbridge/intel/e7505/northbridge.c
index e6e955f..1ea3ce9 100644
--- a/src/northbridge/intel/e7505/northbridge.c
+++ b/src/northbridge/intel/e7505/northbridge.c
@@ -8,6 +8,7 @@
#include <string.h>
#include <bitops.h>
#include "chip.h"
+#include "e7505.h"
#if CONFIG_WRITE_HIGH_TABLES==1
#include <cbmem.h>
@@ -65,17 +66,17 @@
/* Write the ram configuration registers,
* preserving the reserved bits.
*/
- tolm_r = pci_read_config16(mc_dev, 0xc4);
+ tolm_r = pci_read_config16(mc_dev, TOLM);
tolm_r = ((tolmk >> 17) << 11) | (tolm_r & 0x7ff);
- pci_write_config16(mc_dev, 0xc4, tolm_r);
+ pci_write_config16(mc_dev, TOLM, tolm_r);
- remapbase_r = pci_read_config16(mc_dev, 0xc6);
+ remapbase_r = pci_read_config16(mc_dev, REMAPBASE);
remapbase_r = (remapbasek >> 16) | (remapbase_r & 0xfc00);
- pci_write_config16(mc_dev, 0xc6, remapbase_r);
+ pci_write_config16(mc_dev, REMAPBASE, remapbase_r);
- remaplimit_r = pci_read_config16(mc_dev, 0xc8);
+ remaplimit_r = pci_read_config16(mc_dev, REMAPLIMIT);
remaplimit_r = (remaplimitk >> 16) | (remaplimit_r & 0xfc00);
- pci_write_config16(mc_dev, 0xc8, remaplimit_r);
+ pci_write_config16(mc_dev, REMAPLIMIT, remaplimit_r);
/* Report the memory regions */
idx = 10;
@@ -98,12 +99,23 @@
assign_resources(dev->link_list);
}
+static void intel_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+}
+
+static struct pci_operations intel_pci_ops = {
+ .set_subsystem = intel_set_subsystem,
+};
+
static struct device_operations pci_domain_ops = {
.read_resources = pci_domain_read_resources,
.set_resources = pci_domain_set_resources,
.enable_resources = NULL,
.init = NULL,
.scan_bus = pci_domain_scan_bus,
+ .ops_pci = &intel_pci_ops,
.ops_pci_bus = &pci_cf8_conf1,
};
@@ -135,7 +147,8 @@
}
}
-struct chip_operations northbridge_intel_e7501_ops = {
- CHIP_NAME("Intel E7501 Northbridge")
+struct chip_operations northbridge_intel_e7505_ops = {
+ CHIP_NAME("Intel E7505 Northbridge")
.enable_dev = enable_dev,
};
+
diff --git a/src/northbridge/intel/e7505/raminit.c b/src/northbridge/intel/e7505/raminit.c
index f42bef2..46c1903 100644
--- a/src/northbridge/intel/e7505/raminit.c
+++ b/src/northbridge/intel/e7505/raminit.c
@@ -15,7 +15,7 @@
#include <spd.h>
#include <sdram_mode.h>
#include <stdlib.h>
-#include "e7501.h"
+#include "e7505.h"
/*-----------------------------------------------------------------------------
Definitions:
@@ -176,7 +176,8 @@
// without jumping through 36-bit adddressing hoops, even if the
// total memory is > 4 GB. Changing these values may break do_ram_command()!
0x60, 0x00000000, (0x01 << 0) | (0x02 << 8) | (0x03 << 16) | (0x04 << 24),
- 0x64, 0x00000000, (0x05 << 0) | (0x06 << 8) | (0x07 << 16) | (0x08 << 24),
+// 0x64, 0x00000000, (0x05 << 0) | (0x06 << 8) | (0x07 << 16) | (0x08 << 24),
+ 0x64, 0x00000000, (0x04 << 0) | (0x04 << 8) | (0x04 << 16) | (0x04 << 24),
/* DRA - DRAM Row Attribute Register
* 0x70 Row 0,1
@@ -260,7 +261,8 @@
// The only things we need to set here are DRAM idle timer, Back-to-Back Read Turnaround, and
// Back-to-Back Write-Read Turnaround. All others are configured based on SPD.
- 0x78, 0xD7F8FFFF, (1 << 29) | (1 << 27) | (1 << 16),
+// 0x78, 0xD7F8FFFF, (1 << 29) | (1 << 27) | (1 << 16),
+ 0x78, 0xC7F8FFFF, (0x03<<16)|(0x28<<24),
/* FIXME why was I attempting to set a reserved bit? */
/* 0x0100040f */
@@ -314,7 +316,8 @@
// Default to dual-channel mode, ECC, 1-clock address/cmd hold
// NOTE: configure_e7501_dram_controller_mode() configures further
- 0x7c, 0xff8ef8ff, (1 << 22) | (2 << 20) | (1 << 16) | (0 << 8),
+// 0x7c, 0xff8ef8ff, (1 << 22) | (2 << 20) | (1 << 16) | (0 << 8),
+ 0x7c, 0xffcef8f7, 0x00210008,
/* Another Intel undocumented register
* 0x88 - 0x8B
@@ -400,7 +403,8 @@
*/
// Enable D0:D1, disable D2:F1, D3:F1, D4:F1
- 0xe0, 0xffffffe2, (1 << 4) | (1 << 3) | (1 << 2) | (0 << 0),
+// 0xe0, 0xffffffe2, (1 << 4) | (1 << 3) | (1 << 2) | (0 << 0),
+ 0xe0, 0xfffffffa, 0x0,
// Undocumented
0xd8, 0xffff9fff, 0x00000000,
@@ -422,7 +426,7 @@
* [00:00] Unknown - not used?
*/
- 0xf4, 0x3f8ffffd, 0x40300002,
+// 0xf4, 0x3f8ffffd, 0x40300002,
#ifdef SUSPICIOUS_LOOKING_CODE
// SJM: Undocumented.
@@ -432,12 +436,13 @@
};
/* DDR RECOMP tables */
-
+#if 0
// Slew table for 1x drive?
static const uint32_t maybe_1x_slew_table[] = {
0x44332211, 0xc9776655, 0xffffffff, 0xffffffff,
0x22111111, 0x55444332, 0xfffca876, 0xffffffff,
};
+#endif
// Slew table for 2x drive?
static const uint32_t maybe_2x_slew_table[] = {
@@ -478,16 +483,64 @@
#define EXTRA_DELAY DO_DELAY
-static void die_on_spd_error(int spd_return_value)
+/*-----------------------------------------------------------------------------
+Handle (undocumented) control bits in device 0:6.0
+-----------------------------------------------------------------------------*/
+
+/**
+ *
+ */
+static void ram_handle_d060_1(void)
{
- if (spd_return_value < 0)
- die("Error reading SPD info\n");
+ uint32_t dword;
+
+ dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST);
+ dword |= 0x02;
+ pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword);
+
+ dword = pci_read_config32(PCI_DEV(0,6,0), 0xf0);
+ dword |= 0x04;
+ pci_write_config32(PCI_DEV(0,6,0), 0xf0, dword);
+
+ dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST);
+ dword &= ~0x02;
+ pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword);
+}
+
+/**
+ *
+ */
+static void ram_handle_d060_2(void)
+{
+ uint32_t dword;
+ uint8_t revision;
+
+ revision = pci_read_config8(PCI_DEV(0,0,0), 0x08);
+ if (revision >= 3) {
+ dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST);
+ dword |= 0x02;
+ pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword);
+
+ dword = pci_read_config32(PCI_DEV(0,6,0), 0xf0);
+ dword |= 0x18000000;
+ pci_write_config32(PCI_DEV(0,6,0), 0xf0, dword);
+
+ dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST);
+ dword &= ~0x02;
+ pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword);
+ }
}
/*-----------------------------------------------------------------------------
Serial presence detect (SPD) functions:
-----------------------------------------------------------------------------*/
+static void die_on_spd_error(int spd_return_value)
+{
+ if (spd_return_value < 0)
+ die("Error reading SPD info\n");
+}
+
/**
* Calculate the page size for each physical bank of the DIMM:
* log2(page size) = (# columns) + log2(data width)
@@ -843,10 +896,10 @@
*/
static void do_ram_command(uint8_t command, uint16_t jedec_mode_bits)
{
- int i;
+ uint8_t dimm_start_64M_multiple;
+ uint32_t dimm_start_address;
uint32_t dram_controller_mode;
- uint8_t dimm_start_64M_multiple = 0;
- uint16_t e7501_mode_bits = jedec_mode_bits;
+ uint8_t i;
// Configure the RAM command
dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC);
@@ -856,58 +909,43 @@
// RAM_COMMAND_NORMAL is an exception.
// It affects only the memory controller and does not need to be "sent" to the DIMMs.
+ if (command == RAM_COMMAND_NORMAL)
+ return;
- if (command != RAM_COMMAND_NORMAL) {
+ // NOTE: for mode select commands, some of the location address bits are part of the command
+ // Map JEDEC mode bits to E7505
+ if (command == RAM_COMMAND_MRS) {
+ // Host address lines [25:18] map to DIMM address lines [7:0]
+ // Host address lines [17:16] map to DIMM address lines [9:8]
+ // Host address lines [15:4] map to DIMM address lines [11:0]
+ dimm_start_address = (jedec_mode_bits & 0x00ff) << 18;
+ dimm_start_address |= (jedec_mode_bits & 0x0300) << 8;
+ dimm_start_address |= (jedec_mode_bits & 0x0fff) << 4;
+ } else if (command == RAM_COMMAND_EMRS) {
+ // Host address lines [15:4] map to DIMM address lines [11:0]
+ dimm_start_address = (jedec_mode_bits << 4);
+ } else {
+ ASSERT(jedec_mode_bits == 0);
+ dimm_start_address = 0;
+ }
- // Send the command to all DIMMs by accessing a memory location within each
- // NOTE: for mode select commands, some of the location address bits
- // are part of the command
+ // Send the command to all DIMMs by accessing a memory location within each
- // Map JEDEC mode bits to E7501
- if (command == RAM_COMMAND_MRS) {
- // Host address lines [15:5] map to DIMM address lines [12:11, 9:1]
- // The E7501 hard-sets DIMM address lines 10 & 0 to zero
+ dimm_start_64M_multiple = 0;
- ASSERT(!(jedec_mode_bits & 0x0401));
+ for (i = 0; i < (MAX_NUM_CHANNELS * MAX_DIMM_SOCKETS_PER_CHANNEL); ++i) {
- e7501_mode_bits = ((jedec_mode_bits & 0x1800) << (15 - 12)) | // JEDEC bits 11-12 move to bits 14-15
- ((jedec_mode_bits & 0x03FE) << (13 - 9)); // JEDEC bits 1-9 move to bits 5-13
+ uint8_t dimm_end_64M_multiple = pci_read_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + i);
- } else if (command == RAM_COMMAND_EMRS) {
- // Host address lines [15:3] map to DIMM address lines [12:0]
- e7501_mode_bits = jedec_mode_bits <<= 3;
- } else
- ASSERT(jedec_mode_bits == 0);
-
- dimm_start_64M_multiple = 0;
-
- for (i = 0; i < (MAX_NUM_CHANNELS * MAX_DIMM_SOCKETS_PER_CHANNEL); ++i) {
-
- uint8_t dimm_end_64M_multiple =
- pci_read_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + i);
- if (dimm_end_64M_multiple > dimm_start_64M_multiple) {
-
- // This code assumes DRAM row boundaries are all set below 4 GB
- // NOTE: 0x40 * 64 MB == 4 GB
- ASSERT(dimm_start_64M_multiple < 0x40);
-
- // NOTE: 2^26 == 64 MB
-
- uint32_t dimm_start_address =
- dimm_start_64M_multiple << 26;
-
- RAM_DEBUG_MESSAGE(" Sending RAM command to 0x");
- RAM_DEBUG_HEX32(dimm_start_address + e7501_mode_bits);
- RAM_DEBUG_MESSAGE("\n");
-
- read32(dimm_start_address + e7501_mode_bits);
-
+ if (dimm_end_64M_multiple > dimm_start_64M_multiple) {
+ dimm_start_address &= 0x3ffffff;
+ dimm_start_address |= dimm_start_64M_multiple << 26;
+ read32(dimm_start_address);
// Set the start of the next DIMM
- dimm_start_64M_multiple =
- dimm_end_64M_multiple;
- }
+ dimm_start_64M_multiple = dimm_end_64M_multiple;
}
}
+
}
/**
@@ -1136,13 +1174,10 @@
dram_controller_mode >>= 20;
dram_controller_mode &= 3;
if (dram_controller_mode == 2) {
-
uint8_t byte;
RAM_DEBUG_MESSAGE("Initializing ECC state...\n");
- /* Initialize ECC bits , use ECC zero mode (new to 7501) */
- pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x06);
- pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x07);
+ pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x01);
// Wait for scrub cycle to complete
do {
@@ -1150,7 +1185,7 @@
pci_read_config8(PCI_DEV(0, 0, 0), MCHCFGNS);
} while ((byte & 0x08) == 0);
- pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, byte & 0xfc);
+ pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, (byte & 0xfc) | 0x04);
RAM_DEBUG_MESSAGE("ECC state initialized.\n");
/* Clear the ECC error bits */
@@ -1160,9 +1195,6 @@
// Clear DRAM Interface error bits (write-one-clear)
pci_write_config32(PCI_DEV(0, 0, 1), FERR_GLOBAL, 1 << 18);
pci_write_config32(PCI_DEV(0, 0, 1), NERR_GLOBAL, 1 << 18);
-
- // Start normal ECC scrub
- pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 5);
}
}
@@ -1403,11 +1435,11 @@
maybe_dram_read_timing =
pci_read_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL);
- maybe_dram_read_timing &= 0xF00C;
+ maybe_dram_read_timing &= 0xF000;
if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_0) {
dram_timing |= DRT_CAS_2_0;
- maybe_dram_read_timing |= 0xBB1;
+ maybe_dram_read_timing |= 0x0222;
} else if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_5) {
uint32_t dram_row_attributes =
@@ -1438,22 +1470,22 @@
dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88);
dword |= (1 << 26);
pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword);
-
- dword &= 0x0c0007ff; /* patch try register 88 is undocumented tnz */
- dword |= 0xd2109800;
-
+ /* patch try register 88 is undocumented tnz */
+ dword &= 0x0ca17fff;
+ dword |= 0xd14a5000;
pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword);
pci_write_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL,
maybe_dram_read_timing);
- dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88); /* reset master DLL reset */
+ /* clear master DLL reset */
+ dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88);
dword &= ~(1 << 26);
pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword);
return;
- hw_err:
+hw_err:
die(SPD_ERROR);
}
@@ -1627,6 +1659,8 @@
int i;
uint8_t clock_disable = pci_read_config8(PCI_DEV(0, 0, 0), CKDIS);
+ pci_write_config8(PCI_DEV(0,0,0), 0x8e, 0xb0);
+
for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) {
uint8_t socket_mask = 1 << i;
@@ -1727,7 +1761,7 @@
static void ram_set_rcomp_regs(void)
{
uint32_t dword;
- uint8_t maybe_strength_control;
+ uint8_t maybe_strength_control, revision;
RAM_DEBUG_MESSAGE("Setting RCOMP registers.\n");
@@ -1745,81 +1779,105 @@
write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
/* Begin to write the RCOMP registers */
+ write8(RCOMP_MMIO + 0x2c, 0x0);
// Set CMD and DQ/DQS strength to 2x (?)
maybe_strength_control = read8(RCOMP_MMIO + MAYBE_DQCMDSTR) & 0x88;
- maybe_strength_control |= 0x44;
+ maybe_strength_control |= 0x40;
write8(RCOMP_MMIO + MAYBE_DQCMDSTR, maybe_strength_control);
-
write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x80);
write16(RCOMP_MMIO + 0x42, 0);
- write_8dwords(maybe_1x_slew_table, RCOMP_MMIO + 0x60);
-
- // NOTE: some factory BIOS set 0x9088 here. Seems to work either way.
+ // Set CMD and DQ/DQS strength to 2x (?)
+ maybe_strength_control = read8(RCOMP_MMIO + MAYBE_DQCMDSTR) & 0xF8;
+ maybe_strength_control |= 0x04;
+ write8(RCOMP_MMIO + MAYBE_DQCMDSTR, maybe_strength_control);
+ write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x60);
write16(RCOMP_MMIO + 0x40, 0);
// Set RCVEnOut# strength to 2x (?)
maybe_strength_control = read8(RCOMP_MMIO + MAYBE_RCVENSTR) & 0xF8;
- maybe_strength_control |= 4;
+ maybe_strength_control |= 0x04;
write8(RCOMP_MMIO + MAYBE_RCVENSTR, maybe_strength_control);
-
write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x1c0);
write16(RCOMP_MMIO + 0x50, 0);
// Set CS# strength for x4 SDRAM to 2x (?)
- maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CSBSTR) & 0xF8;
- maybe_strength_control |= 4;
+ maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CSBSTR) & 0x88;
+ maybe_strength_control |= 0x04;
write8(RCOMP_MMIO + MAYBE_CSBSTR, maybe_strength_control);
-
write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x140);
write16(RCOMP_MMIO + 0x48, 0);
- // Set CKE strength for x4 SDRAM to 2x (?)
- maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKESTR) & 0xF8;
- maybe_strength_control |= 4;
- write8(RCOMP_MMIO + MAYBE_CKESTR, maybe_strength_control);
+ // Set CS# strength for x4 SDRAM to 2x (?)
+ maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CSBSTR) & 0x8F;
+ maybe_strength_control |= 0x40;
+ write8(RCOMP_MMIO + MAYBE_CSBSTR, maybe_strength_control);
+ write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x160);
+ write16(RCOMP_MMIO + 0x4a, 0);
+ // Set CKE strength for x4 SDRAM to 2x (?)
+ maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKESTR) & 0x88;
+ maybe_strength_control |= 0x04;
+ write8(RCOMP_MMIO + MAYBE_CKESTR, maybe_strength_control);
write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0xa0);
write16(RCOMP_MMIO + 0x44, 0);
- // Set CK strength for x4 SDRAM to 1x (?)
- maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKSTR) & 0xF8;
- maybe_strength_control |= 1;
- write8(RCOMP_MMIO + MAYBE_CKSTR, maybe_strength_control);
+ // Set CKE strength for x4 SDRAM to 2x (?)
+ maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKESTR) & 0x8F;
+ maybe_strength_control |= 0x40;
+ write8(RCOMP_MMIO + MAYBE_CKESTR, maybe_strength_control);
+ write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0xc0);
+ write16(RCOMP_MMIO + 0x46, 0);
+ // Set CK strength for x4 SDRAM to 1x (?)
+ maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKSTR) & 0x88;
+ maybe_strength_control |= 0x01;
+ write8(RCOMP_MMIO + MAYBE_CKSTR, maybe_strength_control);
write_8dwords(maybe_pull_updown_offset_table, RCOMP_MMIO + 0x180);
write16(RCOMP_MMIO + 0x4c, 0);
- write8(RCOMP_MMIO + 0x2c, 0xff);
+ // Set CK strength for x4 SDRAM to 1x (?)
+ maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKSTR) & 0x8F;
+ maybe_strength_control |= 0x10;
+ write8(RCOMP_MMIO + MAYBE_CKSTR, maybe_strength_control);
+ write_8dwords(maybe_pull_updown_offset_table, RCOMP_MMIO + 0x1a0);
+ write16(RCOMP_MMIO + 0x4e, 0);
- // Set the digital filter length to 8 (?)
+
+ dword = read32(RCOMP_MMIO + 0x400);
+ dword &= 0x7f7fffff;
+ write32(RCOMP_MMIO + 0x400, dword);
+
+ dword = read32(RCOMP_MMIO + 0x408);
+ dword &= 0x7f7fffff;
+ write32(RCOMP_MMIO + 0x408, dword);
+
+ ram_handle_d060_1();
+
+ dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST);
+ dword &= 0x3fffffff;
+ pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword);
+
+ revision = pci_read_config8(PCI_DEV(0,0,0), 0x08);
+ if (revision >= 3) {
+ dword = read32(RCOMP_MMIO + MAYBE_SMRCTL);
+ dword &= ~0x100;
+ write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
+ dword = read32(RCOMP_MMIO + MAYBE_SMRCTL);
+ dword |= 0x500;
+ write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
+ }
dword = read32(RCOMP_MMIO + MAYBE_SMRCTL);
-
- // NOTE: Some factory BIOS don't do this.
- // Doesn't seem to matter either way.
- dword &= ~2;
-
- dword |= 1;
+ dword &= ~0x203;
+ dword |= 0x401;
write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
/* Wait 40 usec */
SLOW_DOWN_IO;
- /* unblock updates */
- dword = read32(RCOMP_MMIO + MAYBE_SMRCTL);
- dword &= ~(1 << 9);
- write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
-
- // Force a RCOMP measurement cycle?
- dword |= (1 << 8);
- write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
- dword &= ~(1 << 8);
- write32(RCOMP_MMIO + MAYBE_SMRCTL, dword);
-
- /* Wait 40 usec */
- SLOW_DOWN_IO;
-
+ // Clear the RCOMP MMIO base address
+ pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_SMRBASE, 0);
/*disable access to the rcomp bar */
dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST);
dword &= ~(1 << 22);
@@ -2004,4 +2062,6 @@
ram_set_rcomp_regs();
ram_set_d0f0_regs();
+ ram_handle_d060_2();
}
+