diff --git a/src/mainboard/google/brya/variants/anraggar/overridetree.cb b/src/mainboard/google/brya/variants/anraggar/overridetree.cb
index 9646f29..0c584ee 100644
--- a/src/mainboard/google/brya/variants/anraggar/overridetree.cb
+++ b/src/mainboard/google/brya/variants/anraggar/overridetree.cb
@@ -10,6 +10,10 @@
 		option UF_720P			2
 		option UF_1080P_WF		3
 	end
+	field DB_AUX_BIAS 3 4
+		option REDRIVER		0
+		option SOC		1
+	end
 end
 
 chip soc/intel/alderlake
@@ -60,21 +64,6 @@
 	# [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39.
 	register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x01515"
 
-	# SOC Aux orientation override:
-	# This is a bitfield that corresponds to up to 4 TCSS ports.
-	# Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2.
-	# TcssAuxOri = 0100b
-	# Bit0 set to "0" indicates has retimer on USBC Port0, on the DB.
-	# Bit2 set to "1" indicates no retimer on USBC Port1, on the MB.
-	# Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the
-	# motherboard to USBC connector
-	register "tcss_aux_ori" = "4"
-
-	register "typec_aux_bias_pads[0]" = "{
-		.pad_auxp_dc = GPP_E22,
-		.pad_auxn_dc = GPP_E23
-	}"
-
 	# FIVR configurations for anraggar are disabled since the board doesn't have V1p05 and Vnn
 	# bypass rails implemented.
 	register "ext_fivr_settings" = "{
diff --git a/src/mainboard/google/brya/variants/anraggar/variant.c b/src/mainboard/google/brya/variants/anraggar/variant.c
index 4221a5b..0615618 100644
--- a/src/mainboard/google/brya/variants/anraggar/variant.c
+++ b/src/mainboard/google/brya/variants/anraggar/variant.c
@@ -1,9 +1,39 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 
+#include <baseboard/variants.h>
+#include <chip.h>
 #include <fw_config.h>
 #include <sar.h>
+#include <soc/gpio_soc_defs.h>
 
 const char *get_wifi_sar_cbfs_filename(void)
 {
 	return get_wifi_sar_fw_config_filename(FW_CONFIG_FIELD(WIFI));
 }
+
+void variant_update_soc_chip_config(struct soc_intel_alderlake_config *config)
+{
+	/*
+	* SOC Aux orientation override:
+	* This is a bitfield that corresponds to up to 4 TCSS ports.
+	* Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2.
+	* Bit0, Bit2 set to "0" indicates has retimer on TCSS Port.
+	* Bit0, Bit2 set to "1" indicates no retimer on TCSS Port.
+	* Bit1, Bit3 set to "0" indicates Aux lines are not swapped on TCSS Port.
+	* Bit1, Bit3 set to "1" indicates Aux lines are swapped on TCSS Port.
+	*/
+
+	if (fw_config_probe(FW_CONFIG(DB_AUX_BIAS, SOC))) {
+		printk(BIOS_INFO, "DB DP AUX BIAS connect to SOC.\n");
+		config->tcss_aux_ori = 5;
+		config->typec_aux_bias_pads[0].pad_auxp_dc = GPP_A19;
+		config->typec_aux_bias_pads[0].pad_auxn_dc = GPP_A20;
+		config->typec_aux_bias_pads[1].pad_auxp_dc = GPP_E22;
+		config->typec_aux_bias_pads[1].pad_auxn_dc = GPP_E23;
+	} else {
+		printk(BIOS_INFO, "DB DP AUX BIAS connect to redriver IC.\n");
+		config->tcss_aux_ori = 4;
+		config->typec_aux_bias_pads[1].pad_auxp_dc = GPP_E22;
+		config->typec_aux_bias_pads[1].pad_auxn_dc = GPP_E23;
+	}
+}