pcengines/apu1: Fix and clean up devicetree
Remove functions 0:12.1 and 0:13.1 that do not exist in the hardware.
Disable 0:14.1 IDE controller, as it would only be used with SATA ports
4 and 5 that are not populated with connectors in the hardware.
Disable 0:14.2 HD audio, as it is not implemented in the hardware
Disable 0:14.5 OHCI controller, as ports behind this USB1.1 -only controller
are not populated in the hardware.
Fix some alignment and whitespace.
To my knowledge these changes are not included with SAGE release
pcengines.apu_139_osp.tar.gz, but that tarball does not contain
either devicetree.cb or a pre-compiled static.c file so I cannot tell
for sure.
Change-Id: Idcb8e76645fce7e89a37ff7007531b668f472131
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8328
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
diff --git a/src/mainboard/pcengines/apu1/devicetree.cb b/src/mainboard/pcengines/apu1/devicetree.cb
index a0a6a35..7a60885 100644
--- a/src/mainboard/pcengines/apu1/devicetree.cb
+++ b/src/mainboard/pcengines/apu1/devicetree.cb
@@ -26,29 +26,26 @@
device domain 0 on
subsystemid 0x1022 0x1510 inherit
chip northbridge/amd/agesa/family14 # CPU side of HT root complex
-# device pci 18.0 on # northbridge
- chip northbridge/amd/agesa/family14 # PCI side of HT root complex
- device pci 0.0 on end # Root Complex
- device pci 1.0 off end # Internal Graphics P2P bridge 0x980[2456]
- device pci 4.0 on end # PCIE P2P bridge on-board NIC
- device pci 5.0 on end # PCIE P2P bridge
- device pci 6.0 on end # PCIE P2P bridge PCIe slot
- device pci 7.0 on end # PCIE P2P bridge
- device pci 8.0 on end # NB/SB Link P2P bridge
- end # agesa northbridge
+# device pci 18.0 on # northbridge
+ chip northbridge/amd/agesa/family14 # PCI side of HT root complex
+ device pci 0.0 on end # Root Complex
+ device pci 1.0 off end # Internal Graphics P2P bridge 0x980[2456]
+ device pci 4.0 on end # PCIE P2P bridge on-board NIC
+ device pci 5.0 on end # PCIE P2P bridge
+ device pci 6.0 on end # PCIE P2P bridge PCIe slot
+ device pci 7.0 on end # PCIE P2P bridge
+ device pci 8.0 on end # NB/SB Link P2P bridge
+ end # agesa northbridge
- chip southbridge/amd/cimx/sb800 # it is under NB/SB Link, but on the same pri bus
- device pci 11.0 on end # SATA
- device pci 12.0 on end # OHCI USB 0-4
- device pci 12.1 on end # OHCI USB 0-4
- device pci 12.2 on end # EHCI USB 0-4
- device pci 13.0 on end # OHCI USB 5-9
- device pci 13.1 on end # OHCI USB 5-9
- device pci 13.2 on end # EHCI USB 5-9
- device pci 14.0 on # SM
- end # SM
- device pci 14.1 on end # IDE 0x439c
- device pci 14.2 on end # HDA 0x4383
+ chip southbridge/amd/cimx/sb800 # it is under NB/SB Link, but on the same pri bus
+ device pci 11.0 on end # SATA
+ device pci 12.0 on end # OHCI USB 0-4
+ device pci 12.2 on end # EHCI USB 0-4
+ device pci 13.0 on end # OHCI USB 5-9
+ device pci 13.2 on end # EHCI USB 5-9
+ device pci 14.0 on end # SMBus
+ device pci 14.1 off end # IDE 0x439c
+ device pci 14.2 off end # HDA 0x4383
device pci 14.3 on # LPC 0x439d
chip superio/nuvoton/nct5104d
register "irq_trigger_type" = "0"
@@ -76,20 +73,20 @@
device pnp 2e.607 off end
device pnp 2e.e off end
end
- end #LPC
- device pci 14.4 on end # PCIB 0x4384, NOTE: PCI interface pins shared with GPIO {GPIO 35:0}
- device pci 14.5 on end # OHCI FS/LS USB
- #device pci 14.6 off end # Hudson-E1 GbE MAC: Broadcom BCM5785 (14E4:1699)
- device pci 15.0 on end # PCIe PortA
- device pci 15.1 off end # PCIe PortB
- device pci 15.2 off end # PCIe PortC
- device pci 15.3 off end # PCIe PortD
- device pci 16.0 on end # OHCI USB 10-13
- device pci 16.2 on end # EHCI USB 10-13
- register "gpp_configuration" = "0"
- register "disconnect_pcib" = "1"
- register "boot_switch_sata_ide" = "0" # 0: boot from SATA. 1: IDE
- end #southbridge/amd/cimx/sb800
+ end #LPC
+ device pci 14.4 on end # PCIB 0x4384
+ device pci 14.5 off end # OHCI FS/LS USB
+ #device pci 14.6 off end # Hudson-E1 GbE MAC: Broadcom BCM5785 (14E4:1699)
+ device pci 15.0 on end # PCIe PortA
+ device pci 15.1 off end # PCIe PortB
+ device pci 15.2 off end # PCIe PortC
+ device pci 15.3 off end # PCIe PortD
+ device pci 16.0 on end # OHCI USB 10-13
+ device pci 16.2 on end # EHCI USB 10-13
+ register "gpp_configuration" = "0"
+ register "disconnect_pcib" = "1"
+ register "boot_switch_sata_ide" = "0" # 0: boot from SATA. 1: IDE
+ end #southbridge/amd/cimx/sb800
# end # device pci 18.0
# These seem unnecessary
device pci 18.0 on end
diff --git a/src/mainboard/pcengines/apu1/mptable.c b/src/mainboard/pcengines/apu1/mptable.c
index 18bdb97..03fa9f3 100644
--- a/src/mainboard/pcengines/apu1/mptable.c
+++ b/src/mainboard/pcengines/apu1/mptable.c
@@ -114,17 +114,6 @@
PCI_INT(0x3, 0x0, 0x0, intr_data_ptr[PIRQ_E]); /* Use INTE */
PCI_INT(0x4, 0x0, 0x0, intr_data_ptr[PIRQ_E]); /* Use INTE */
- /* PCI slots */
- device_t dev = dev_find_slot(0, PCI_DEVFN(0x14, 4));
- if (dev && dev->enabled) {
- u8 bus_pci = dev->link_list->secondary;
- /* PCI_SLOT 0 */
- PCI_INT(bus_pci, 0x5, 0x0, intr_data_ptr[PIRQ_E]); /* INTA -> INTE */
- PCI_INT(bus_pci, 0x5, 0x1, intr_data_ptr[PIRQ_F]); /* INTB -> INTF */
- PCI_INT(bus_pci, 0x5, 0x2, intr_data_ptr[PIRQ_G]); /* INTC -> INTG */
- PCI_INT(bus_pci, 0x5, 0x3, intr_data_ptr[PIRQ_H]); /* INTD -> INTH */
- }
-
/* PCIe PortA */
PCI_INT(0x0, 0x15, 0x0, intr_data_ptr[PIRQ_E]); /* INTA -> INTE */
/* PCIe PortB */