[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt20-1+deb8u3 (2016-01-17)
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000c7c54fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000c7c55000-0x00000000dfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021effffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: ASROCK E350M1/E350M1, BIOS 4.2-968-g98fc426 01/27/2016
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x21f000 max_arch_pfn = 0x1000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-back
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FF8000000 write-back
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 base 0FFC00000 mask FFFC00000 write-protect
[    0.000000]   7 disabled
[    0.000000] TOM2: 000000021f000000 aka 8688M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] found SMP MP-table at [mem 0x000f5d20-0x000f5d2f] mapped at [c00f5d20]
[    0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] init_memory_mapping: [mem 0x37200000-0x373fffff]
[    0.000000]  [mem 0x37200000-0x373fffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x34000000-0x371fffff]
[    0.000000]  [mem 0x34000000-0x371fffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x33ffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x33ffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x37400000-0x375fdfff]
[    0.000000]  [mem 0x37400000-0x375fdfff] page 4k
[    0.000000] BRK [0x0179c000, 0x0179cfff] PGTABLE
[    0.000000] BRK [0x0179d000, 0x0179efff] PGTABLE
[    0.000000] BRK [0x0179f000, 0x0179ffff] PGTABLE
[    0.000000] BRK [0x017a0000, 0x017a0fff] PGTABLE
[    0.000000] RAMDISK: [mem 0x3604a000-0x3701cfff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F5F20 000024 (v02 CORE  )
[    0.000000] ACPI: XSDT 0x00000000C7C700E0 000064 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: FACP 0x00000000C7C72740 0000F4 (v04 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: DSDT 0x00000000C7C70280 0024B6 (v02 ASROCK COREBOOT 00010001 INTL 20140926)
[    0.000000] ACPI: FACS 0x00000000C7C70240 000040
[    0.000000] ACPI: FACS 0x00000000C7C70240 000040
[    0.000000] ACPI: SSDT 0x00000000C7C72840 000046 (v02 CORE   COREBOOT 0000002A CORE 0000002A)
[    0.000000] ACPI: TCPA 0x00000000C7C72890 000032 (v02 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: APIC 0x00000000C7C728D0 00005C (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: HEST 0x00000000C7C72930 000028 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SSDT 0x00000000C7C72960 00168E (v02 AMD    ALIB     00000001 MSFT 04000000)
[    0.000000] ACPI: SSDT 0x00000000C7C73FF0 0003DE (v01 AMD    POWERNOW 00000001 AMD  00000001)
[    0.000000] ACPI: HPET 0x00000000C7C743D0 000038 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 7802MB HIGHMEM available.
[    0.000000] 885MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 375fe000
[    0.000000]   low ram: 0 - 375fe000
[    0.000000] BRK [0x017a1000, 0x017a1fff] PGTABLE
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   Normal   [mem 0x01000000-0x375fdfff]
[    0.000000]   HighMem  [mem 0x375fe000-0x1effffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0xc7c54fff]
[    0.000000]   node   0: [mem 0x00000000-0x1effffff]
[    0.000000] On node 0 totalpages: 1993715
[    0.000000] free_area_init_node: node 0, pgdat c165d180, node_mem_map f1c6a020
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   Normal zone: 1740 pages used for memmap
[    0.000000]   Normal zone: 222718 pages, LIFO batch:31
[    0.000000]   HighMem zone: 15605 pages used for memmap
[    0.000000]   HighMem zone: 1766999 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x43538210 base: 0xfed00000
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] e820: [mem 0xe0000000-0xf7ffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @f75d0000 s34752 r0 d22592 u57344
[    0.000000] pcpu-alloc: s34752 r0 d22592 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1991943
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.16.0-4-686-pae root=UUID=0198e82a-32df-4f18-bec0-3e08802b084d ro quiet noisapnp pcie_aspm=force pcie_aspm.policy=powersave nmi_watchdog=0
[    0.000000] PCIe ASPM is forcibly enabled
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (000375fe:0021f000)
[    0.000000] Initializing Movable for node 0 (00000000:00000000)
[    0.000000] Memory: 7880292K/7974860K available (4608K kernel code, 522K rwdata, 1452K rodata, 656K init, 460K bss, 94568K reserved, 7067996K highmem)
[    0.000000] virtual kernel memory layout:
    fixmap  : 0xffd36000 - 0xfffff000   (2852 kB)
    pkmap   : 0xff600000 - 0xff800000   (2048 kB)
    vmalloc : 0xf7dfe000 - 0xff5fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf75fe000   ( 885 MB)
      .init : 0xc1671000 - 0xc1715000   ( 656 kB)
      .data : 0xc148044c - 0xc166fb40   (1981 kB)
      .text : 0xc1000000 - 0xc148044c   (4609 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:2304 nr_irqs:512 16
[    0.000000] CPU 0 irqstacks, hard=f1806000 soft=f1808000
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1600.061 MHz processor
[    0.000055] Calibrating delay loop (skipped), value calculated using timer frequency.. 3200.12 BogoMIPS (lpj=6400244)
[    0.000062] pid_max: default: 32768 minimum: 301
[    0.000080] ACPI: Core revision 20140424
[    0.005857] ACPI: All ACPI Tables successfully acquired
[    0.005904] Security Framework initialized
[    0.005924] AppArmor: AppArmor disabled by boot time parameter
[    0.005927] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.005961] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.005966] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.006369] Initializing cgroup subsys memory
[    0.006381] Initializing cgroup subsys devices
[    0.006395] Initializing cgroup subsys freezer
[    0.006402] Initializing cgroup subsys net_cls
[    0.006414] Initializing cgroup subsys blkio
[    0.006422] Initializing cgroup subsys perf_event
[    0.006427] Initializing cgroup subsys net_prio
[    0.006470] CPU: Physical Processor ID: 0
[    0.006473] CPU: Processor Core ID: 0
[    0.006479] mce: CPU supports 6 MCE banks
[    0.006499] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4, 1GB 0
tlb_flushall_shift: 6
[    0.006829] Freeing SMP alternatives memory: 20K (c1715000 - c171a000)
[    0.009016] ftrace: allocating 20810 entries in 41 pages
[    0.028441] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.028892] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.068585] smpboot: CPU0: AMD E-350D APU with Radeon(tm) HD Graphics (fam: 14, model: 02, stepping: 00)
[    0.176555] Performance Events: AMD PMU driver.
[    0.176565] ... version:                0
[    0.176568] ... bit width:              48
[    0.176570] ... generic registers:      4
[    0.176573] ... value mask:             0000ffffffffffff
[    0.176576] ... max period:             00007fffffffffff
[    0.176579] ... fixed-purpose events:   0
[    0.176581] ... event mask:             000000000000000f
[    0.179820] CPU 1 irqstacks, hard=f193e000 soft=f1940000
[    0.179828] x86: Booting SMP configuration:
[    0.179832] .... node  #0, CPUs:      #1
[    0.189872] Initializing CPU#1
[    0.193043] x86: Booted up 1 node, 2 CPUs
[    0.193050] smpboot: Total of 2 processors activated (6400.24 BogoMIPS)
[    0.193946] devtmpfs: initialized
[    0.196727] pinctrl core: initialized pinctrl subsystem
[    0.196899] NET: Registered protocol family 16
[    0.197146] cpuidle: using governor ladder
[    0.197153] cpuidle: using governor menu
[    0.197368] ACPI: bus type PCI registered
[    0.197373] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.197692] PCI : PCI BIOS area is rw and x. Use pci=nobios if you want it NX.
[    0.197697] bios32_service(0x49435024): not present
[    0.197700] PCI: Using configuration type 1 for base access
[    0.197702] PCI: Using configuration type 1 for extended access
[    0.210932] ACPI: Added _OSI(Module Device)
[    0.210941] ACPI: Added _OSI(Processor Device)
[    0.210944] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.210948] ACPI: Added _OSI(Processor Aggregator Device)
[    0.213210] ACPI: Executed 2 blocks of module-level executable AML code
[    0.217533] ACPI: Interpreter enabled
[    0.217554] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[    0.217580] ACPI: (supports S0 S1 S3 S4 S5)
[    0.217584] ACPI: Using IOAPIC for interrupt routing
[    0.217614] HEST: Table parsing has been initialized.
[    0.217622] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.233499] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.233515] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.233653] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.234206] PCI host bridge to bus 0000:00
[    0.234213] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.234219] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.234226] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.234230] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.234235] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xffffffff]
[    0.234252] pci 0000:00:00.0: [1022:1510] type 00 class 0x060000
[    0.234439] pci 0000:00:01.0: [1002:9802] type 00 class 0x030000
[    0.234459] pci 0000:00:01.0: reg 0x10: [mem 0xe0000000-0xefffffff pref]
[    0.234470] pci 0000:00:01.0: reg 0x14: [io  0x2000-0x20ff]
[    0.234481] pci 0000:00:01.0: reg 0x18: [mem 0xf0100000-0xf013ffff]
[    0.234549] pci 0000:00:01.0: supports D1 D2
[    0.234629] pci 0000:00:01.0: System wakeup disabled by ACPI
[    0.234723] pci 0000:00:01.1: [1002:1314] type 00 class 0x040300
[    0.234740] pci 0000:00:01.1: reg 0x10: [mem 0xf0140000-0xf0143fff]
[    0.234818] pci 0000:00:01.1: supports D1 D2
[    0.234897] pci 0000:00:01.1: System wakeup disabled by ACPI
[    0.235087] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601
[    0.235115] pci 0000:00:11.0: reg 0x10: [io  0x2410-0x2417]
[    0.235130] pci 0000:00:11.0: reg 0x14: [io  0x2420-0x2423]
[    0.235145] pci 0000:00:11.0: reg 0x18: [io  0x2418-0x241f]
[    0.235159] pci 0000:00:11.0: reg 0x1c: [io  0x2424-0x2427]
[    0.235173] pci 0000:00:11.0: reg 0x20: [io  0x2400-0x240f]
[    0.235188] pci 0000:00:11.0: reg 0x24: [mem 0xf014b000-0xf014b3ff]
[    0.235458] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310
[    0.235479] pci 0000:00:12.0: reg 0x10: [mem 0xf0148000-0xf0148fff]
[    0.235627] pci 0000:00:12.0: System wakeup disabled by ACPI
[    0.235788] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320
[    0.235816] pci 0000:00:12.2: reg 0x10: [mem 0xf014c000-0xf014c0ff]
[    0.235928] pci 0000:00:12.2: supports D1 D2
[    0.235932] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.236014] pci 0000:00:12.2: System wakeup disabled by ACPI
[    0.236114] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310
[    0.236135] pci 0000:00:13.0: reg 0x10: [mem 0xf0149000-0xf0149fff]
[    0.236281] pci 0000:00:13.0: System wakeup disabled by ACPI
[    0.236445] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320
[    0.236473] pci 0000:00:13.2: reg 0x10: [mem 0xf014d000-0xf014d0ff]
[    0.236585] pci 0000:00:13.2: supports D1 D2
[    0.236589] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[    0.236671] pci 0000:00:13.2: System wakeup disabled by ACPI
[    0.236836] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
[    0.237108] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
[    0.237139] pci 0000:00:14.2: reg 0x10: [mem 0xf0144000-0xf0147fff 64bit]
[    0.237230] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.237458] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100
[    0.237752] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
[    0.237873] pci 0000:00:14.4: System wakeup disabled by ACPI
[    0.238025] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310
[    0.238046] pci 0000:00:14.5: reg 0x10: [mem 0xf014a000-0xf014afff]
[    0.238196] pci 0000:00:14.5: System wakeup disabled by ACPI
[    0.238356] pci 0000:00:15.0: [1002:43a0] type 01 class 0x060400
[    0.238464] pci 0000:00:15.0: supports D1 D2
[    0.238552] pci 0000:00:15.0: System wakeup disabled by ACPI
[    0.238713] pci 0000:00:15.1: [1002:43a1] type 01 class 0x060400
[    0.238828] pci 0000:00:15.1: supports D1 D2
[    0.238916] pci 0000:00:15.1: System wakeup disabled by ACPI
[    0.239077] pci 0000:00:18.0: [1022:1700] type 00 class 0x060000
[    0.239245] pci 0000:00:18.1: [1022:1701] type 00 class 0x060000
[    0.239409] pci 0000:00:18.2: [1022:1702] type 00 class 0x060000
[    0.239576] pci 0000:00:18.3: [1022:1703] type 00 class 0x060000
[    0.239757] pci 0000:00:18.4: [1022:1704] type 00 class 0x060000
[    0.239922] pci 0000:00:18.5: [1022:1718] type 00 class 0x060000
[    0.240083] pci 0000:00:18.6: [1022:1716] type 00 class 0x060000
[    0.240251] pci 0000:00:18.7: [1022:1719] type 00 class 0x060000
[    0.240683] pci 0000:00:14.4: PCI bridge to [bus 01] (subtractive decode)
[    0.240699] pci 0000:00:14.4:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.240703] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.240708] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.240712] pci 0000:00:14.4:   bridge window [mem 0xe0000000-0xffffffff] (subtractive decode)
[    0.240816] pci 0000:00:15.0: PCI bridge to [bus 02]
[    0.241028] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000
[    0.241058] pci 0000:03:00.0: reg 0x10: [io  0x1000-0x10ff]
[    0.241105] pci 0000:03:00.0: reg 0x18: [mem 0xf0004000-0xf0004fff 64bit pref]
[    0.241132] pci 0000:03:00.0: reg 0x20: [mem 0xf0000000-0xf0003fff 64bit pref]
[    0.241261] pci 0000:03:00.0: supports D1 D2
[    0.241265] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.249397] pci 0000:00:15.1: PCI bridge to [bus 03]
[    0.249416] pci 0000:00:15.1:   bridge window [io  0x1000-0x1fff]
[    0.249430] pci 0000:00:15.1:   bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[    0.249465] pci_bus 0000:00: on NUMA node 0
[    0.250401] ACPI: PCI Interrupt Link [INTA] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.250642] ACPI: PCI Interrupt Link [INTB] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.250739] ACPI: PCI Interrupt Link [INTC] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.250834] ACPI: PCI Interrupt Link [INTD] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.250929] ACPI: PCI Interrupt Link [INTE] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.251024] ACPI: PCI Interrupt Link [INTF] (IRQs 9) *0
[    0.251115] ACPI: PCI Interrupt Link [INTG] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.251214] ACPI: PCI Interrupt Link [INTH] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.251477] ACPI: Enabled 6 GPEs in block 00 to 1F
[    0.251959] vgaarb: setting as boot device: PCI:0000:00:01.0
[    0.251968] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[    0.251980] vgaarb: loaded
[    0.251984] vgaarb: bridge control possible 0000:00:01.0
[    0.252135] PCI: Using ACPI for IRQ routing
[    0.252141] PCI: pci_cache_line_size set to 64 bytes
[    0.252227] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    0.252232] e820: reserve RAM buffer [mem 0xc7c55000-0xc7ffffff]
[    0.252236] e820: reserve RAM buffer [mem 0x21f000000-0x21fffffff]
[    0.252619] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.252628] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[    0.254808] Switched to clocksource hpet
[    0.265381] pnp: PnP ACPI init
[    0.265413] ACPI: bus type PNP registered
[    0.265872] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.266150] pnp: PnP ACPI: found 1 devices
[    0.266153] ACPI: bus type PNP unregistered
[    0.266160] PnPBIOS: Disabled by ACPI PNP
[    0.310353] pci 0000:00:14.4: PCI bridge to [bus 01]
[    0.310379] pci 0000:00:15.0: PCI bridge to [bus 02]
[    0.310397] pci 0000:00:15.1: PCI bridge to [bus 03]
[    0.310404] pci 0000:00:15.1:   bridge window [io  0x1000-0x1fff]
[    0.310416] pci 0000:00:15.1:   bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[    0.310429] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.310433] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.310438] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.310443] pci_bus 0000:00: resource 7 [mem 0xe0000000-0xffffffff]
[    0.310448] pci_bus 0000:01: resource 4 [io  0x0000-0x0cf7]
[    0.310452] pci_bus 0000:01: resource 5 [io  0x0d00-0xffff]
[    0.310456] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
[    0.310461] pci_bus 0000:01: resource 7 [mem 0xe0000000-0xffffffff]
[    0.310465] pci_bus 0000:03: resource 0 [io  0x1000-0x1fff]
[    0.310470] pci_bus 0000:03: resource 2 [mem 0xf0000000-0xf00fffff 64bit pref]
[    0.310633] NET: Registered protocol family 2
[    0.311354] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.311386] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.311424] TCP: Hash tables configured (established 8192 bind 8192)
[    0.311472] TCP: reno registered
[    0.311477] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.311490] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.311724] NET: Registered protocol family 1
[    0.311758] pci 0000:00:01.0: Video device with shadowed ROM
[    0.369029] PCI: CLS 64 bytes, default 64
[    0.369158] Unpacking initramfs...
[    1.004781] Freeing initrd memory: 16204K (f604a000 - f701d000)
[    1.005576] microcode: CPU0: patch_level=0x05000119
[    1.005596] microcode: CPU1: patch_level=0x05000119
[    1.005949] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.005970] LVT offset 0 assigned for vector 0x400
[    1.006097] perf: AMD IBS detected (0x000000ff)
[    1.007203] futex hash table entries: 512 (order: 3, 32768 bytes)
[    1.007336] audit: initializing netlink subsys (disabled)
[    1.007377] audit: type=2000 audit(1454010953.900:1): initialized
[    1.008191] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.008232] zbud: loaded
[    1.008830] VFS: Disk quotas dquot_6.5.2
[    1.008936] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.009118] msgmni has been set to 1618
[    1.010338] alg: No test for stdrng (krng)
[    1.010403] bounce: pool size: 64 pages
[    1.010521] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.010671] io scheduler noop registered
[    1.010677] io scheduler deadline registered
[    1.010882] io scheduler cfq registered (default)
[    1.011458] pcieport 0000:00:15.0: irq 40 for MSI/MSI-X
[    1.011894] pcieport 0000:00:15.1: irq 41 for MSI/MSI-X
[    1.012145] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt
[    1.012154] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded
[    1.012188] pcieport 0000:00:15.1: Signaling PME through PCIe PME interrupt
[    1.012193] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[    1.012201] pcie_pme 0000:00:15.1:pcie01: service driver pcie_pme loaded
[    1.012237] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.012277] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.012396] GHES: Failed to enable APEI firmware first mode.
[    1.012407] isapnp: ISA Plug & Play support disabled
[    1.012792] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.033503] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.035128] Linux agpgart interface v0.103
[    1.035508] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    1.039380] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.039401] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.040258] mousedev: PS/2 mouse device common for all mice
[    1.040477] rtc_cmos 00:00: RTC can wake from S4
[    1.040823] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0
[    1.040932] rtc_cmos 00:00: alarms up to one day, 114 bytes nvram, hpet irqs
[    1.040964] ledtrig-cpu: registered to indicate activity on CPUs
[    1.041285] TCP: cubic registered
[    1.041416] NET: Registered protocol family 10
[    1.041927] mip6: Mobile IPv6
[    1.041934] NET: Registered protocol family 17
[    1.041946] mpls_gso: MPLS GSO support
[    1.042551] Using IPI No-Shortcut mode
[    1.043017] registered taskstats version 1
[    1.043930] rtc_cmos 00:00: setting system clock to 2016-01-28 19:55:54 UTC (1454010954)
[    1.044048] PM: Hibernation image not present or could not be loaded.
[    1.044619] Freeing unused kernel memory: 656K (c1671000 - c1715000)
[    1.044765] Write protecting the kernel text: 4612k
[    1.044908] Write protecting the kernel read-only data: 1456k
[    1.044911] NX-protecting the kernel data: 3580k
[    1.143986] systemd-udevd[61]: starting version 215
[    1.144798] random: systemd-udevd urandom read with 0 bits of entropy available
[    1.172417] ACPI: bus type USB registered
[    1.172486] usbcore: registered new interface driver usbfs
[    1.172513] usbcore: registered new interface driver hub
[    1.172676] usbcore: registered new device driver usb
[    1.173684] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.174024] ehci-pci: EHCI PCI platform driver
[    1.174434] QUIRK: Enable AMD PLL fix
[    1.174476] ehci-pci 0000:00:12.2: EHCI Host Controller
[    1.174489] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 1
[    1.174504] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.174590] ehci-pci 0000:00:12.2: debug port 1
[    1.174666] ehci-pci 0000:00:12.2: irq 17, io mem 0xf014c000
[    1.176748] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.177582] SCSI subsystem initialized
[    1.181139] libata version 3.00 loaded.
[    1.183037] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[    1.183168] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.183173] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.183178] usb usb1: Product: EHCI Host Controller
[    1.183182] usb usb1: Manufacturer: Linux 3.16.0-4-686-pae ehci_hcd
[    1.183186] usb usb1: SerialNumber: 0000:00:12.2
[    1.183500] hub 1-0:1.0: USB hub found
[    1.183518] hub 1-0:1.0: 5 ports detected
[    1.184400] ehci-pci 0000:00:13.2: EHCI Host Controller
[    1.184414] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 2
[    1.184423] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.184440] ehci-pci 0000:00:13.2: debug port 1
[    1.184497] ehci-pci 0000:00:13.2: irq 17, io mem 0xf014d000
[    1.185126] thermal LNXTHERM:00: registered as thermal_zone0
[    1.185135] ACPI: Thermal Zone [TZ00] (36 C)
[    1.194912] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[    1.195083] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.195092] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.195097] usb usb2: Product: EHCI Host Controller
[    1.195101] usb usb2: Manufacturer: Linux 3.16.0-4-686-pae ehci_hcd
[    1.195105] usb usb2: SerialNumber: 0000:00:13.2
[    1.195405] hub 2-0:1.0: USB hub found
[    1.195423] hub 2-0:1.0: 5 ports detected
[    1.196051] ahci 0000:00:11.0: version 3.0
[    1.196679] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[    1.196686] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck led clo pmp pio slum part 
[    1.197904] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.198433] r8169 0000:03:00.0: irq 42 for MSI/MSI-X
[    1.199083] r8169 0000:03:00.0 eth0: RTL8168e/8111e at 0xf7e0e000, bc:5f:f4:c8:d3:98, XID 0c200000 IRQ 42
[    1.199088] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.199408] ohci-pci: OHCI PCI platform driver
[    1.200361] scsi0 : ahci
[    1.206035] scsi1 : ahci
[    1.212751] scsi2 : ahci
[    1.214878] scsi3 : ahci
[    1.222968] scsi4 : ahci
[    1.228814] scsi5 : ahci
[    1.228977] ata1: SATA max UDMA/133 abar m1024@0xf014b000 port 0xf014b100 irq 19
[    1.228983] ata2: SATA max UDMA/133 abar m1024@0xf014b000 port 0xf014b180 irq 19
[    1.228988] ata3: SATA max UDMA/133 abar m1024@0xf014b000 port 0xf014b200 irq 19
[    1.228994] ata4: SATA max UDMA/133 abar m1024@0xf014b000 port 0xf014b280 irq 19
[    1.228999] ata5: SATA max UDMA/133 abar m1024@0xf014b000 port 0xf014b300 irq 19
[    1.229004] ata6: SATA max UDMA/133 abar m1024@0xf014b000 port 0xf014b380 irq 19
[    1.229393] ohci-pci 0000:00:12.0: OHCI PCI host controller
[    1.229413] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 3
[    1.229480] ohci-pci 0000:00:12.0: irq 18, io mem 0xf0148000
[    1.287366] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.287376] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.287381] usb usb3: Product: OHCI PCI host controller
[    1.287385] usb usb3: Manufacturer: Linux 3.16.0-4-686-pae ohci_hcd
[    1.287389] usb usb3: SerialNumber: 0000:00:12.0
[    1.288000] hub 3-0:1.0: USB hub found
[    1.288024] hub 3-0:1.0: 5 ports detected
[    1.288652] ohci-pci 0000:00:13.0: OHCI PCI host controller
[    1.288666] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 4
[    1.288718] ohci-pci 0000:00:13.0: irq 18, io mem 0xf0149000
[    1.347265] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.347275] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.347280] usb usb4: Product: OHCI PCI host controller
[    1.347284] usb usb4: Manufacturer: Linux 3.16.0-4-686-pae ohci_hcd
[    1.347288] usb usb4: SerialNumber: 0000:00:13.0
[    1.347892] hub 4-0:1.0: USB hub found
[    1.347915] hub 4-0:1.0: 5 ports detected
[    1.348543] ohci-pci 0000:00:14.5: OHCI PCI host controller
[    1.348557] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 5
[    1.348607] ohci-pci 0000:00:14.5: irq 18, io mem 0xf014a000
[    1.407285] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    1.407295] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.407299] usb usb5: Product: OHCI PCI host controller
[    1.407304] usb usb5: Manufacturer: Linux 3.16.0-4-686-pae ohci_hcd
[    1.407307] usb usb5: SerialNumber: 0000:00:14.5
[    1.407911] hub 5-0:1.0: USB hub found
[    1.407934] hub 5-0:1.0: 2 ports detected
[    1.547194] ata1: SATA link down (SStatus 0 SControl 300)
[    1.551184] ata2: SATA link down (SStatus 0 SControl 300)
[    1.555185] ata3: SATA link down (SStatus 0 SControl 300)
[    1.559184] ata6: SATA link down (SStatus 0 SControl 300)
[    1.559240] ata5: SATA link down (SStatus 0 SControl 300)
[    1.731136] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.731877] ata4.00: ATA-9: M4-CT256M4SSD2, 070H, max UDMA/100
[    1.731887] ata4.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.732676] ata4.00: configured for UDMA/100
[    1.733277] scsi 3:0:0:0: Direct-Access     ATA      M4-CT256M4SSD2   070H PQ: 0 ANSI: 5
[    1.744912] sd 3:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[    1.745369] sd 3:0:0:0: [sda] Write Protect is off
[    1.745382] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.745806] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.747228]  sda: sda1 sda2
[    1.748274] sd 3:0:0:0: [sda] Attached SCSI disk
[    1.749505] sd 3:0:0:0: Attached scsi generic sg0 type 0
[    1.805212] device-mapper: uevent: version 1.0.3
[    1.805375] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    2.003211] tsc: Refined TSC clocksource calibration: 1599.999 MHz
[    2.067119] usb 2-2: new high-speed USB device number 2 using ehci-pci
[    2.216747] usb 2-2: New USB device found, idVendor=148f, idProduct=2870
[    2.216764] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.216773] usb 2-2: Product: 802.11 n WLAN
[    2.216781] usb 2-2: Manufacturer: Ralink
[    2.355121] usb 3-1: new low-speed USB device number 2 using ohci-pci
[    2.527389] usb 3-1: New USB device found, idVendor=046d, idProduct=c312
[    2.527406] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.527416] usb 3-1: Product: USB Multimedia Keyboard
[    2.527424] usb 3-1: Manufacturer: LITEON Technology
[    2.531960] hidraw: raw HID events driver (C) Jiri Kosina
[    2.538740] usbcore: registered new interface driver usbhid
[    2.538748] usbhid: USB HID core driver
[    2.540849] input: LITEON Technology USB Multimedia Keyboard as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.0/0003:046D:C312.0001/input/input2
[    2.540980] hid-generic 0003:046D:C312.0001: input,hidraw0: USB HID v1.10 Keyboard [LITEON Technology USB Multimedia Keyboard] on usb-0000:00:12.0-1/input0
[    2.791120] usb 3-2: new full-speed USB device number 3 using ohci-pci
[    2.956294] usb 3-2: New USB device found, idVendor=1b1a, idProduct=7001
[    2.956311] usb 3-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.956320] usb 3-2: Product:  USB  Mouse 
[    2.963024] input:  USB  Mouse  as /devices/pci0000:00/0000:00:12.0/usb3/3-2/3-2:1.0/0003:1B1A:7001.0002/input/input3
[    2.963205] hid-generic 0003:1B1A:7001.0002: input,hidraw1: USB HID v1.10 Mouse [ USB  Mouse ] on usb-0000:00:12.0-2/input0
[    2.968528] input:  USB  Mouse  as /devices/pci0000:00/0000:00:12.0/usb3/3-2/3-2:1.1/0003:1B1A:7001.0003/input/input4
[    2.968667] hid-generic 0003:1B1A:7001.0003: input,hidraw2: USB HID v1.10 Keyboard [ USB  Mouse ] on usb-0000:00:12.0-2/input1
[    3.003460] Switched to clocksource tsc
[    5.639198] NET: Registered protocol family 38
[    6.036083] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[    6.170367] random: nonblocking pool is initialized
[    7.006600] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    7.006633] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    7.006647] systemd[1]: Cannot add dependency job for unit NetworkManager-wait-online.service, ignoring: Unit NetworkManager-wait-online.service failed to load: No such file or directory.
[    7.006772] systemd[1]: Found ordering cycle on basic.target/start
[    7.006780] systemd[1]: Found dependency on sysinit.target/start
[    7.006787] systemd[1]: Found dependency on rpcbind.service/start
[    7.006794] systemd[1]: Found dependency on network-online.target/start
[    7.006848] systemd[1]: Found dependency on network.target/start
[    7.006855] systemd[1]: Found dependency on systemd-networkd.service/start
[    7.006861] systemd[1]: Found dependency on dbus.service/start
[    7.006866] systemd[1]: Found dependency on basic.target/start
[    7.006873] systemd[1]: Breaking ordering cycle by deleting job rpcbind.service/start
[    7.006881] systemd[1]: Job rpcbind.service/start deleted to break ordering cycle starting with basic.target/start
[    8.178652] systemd[1]: tmp.mount: Directory /tmp to mount over is not empty, mounting anyway.
[    8.409879] lp: driver loaded but no devices found
[    8.432526] ppdev: user-space parallel port driver
[    8.451672] fuse init (API version 7.23)
[    8.498151] w83627ehf: Found NCT6775F chip at 0x290
[    8.502966] systemd-udevd[237]: starting version 215
[    8.942578] ACPI: acpi_idle registered with cpuidle
[    8.967302] acpi-cpufreq: overriding BIOS provided _PSD data
[    8.972911] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
[    8.972926] ACPI: Power Button [PWRB]
[    8.973048] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[    8.973053] ACPI: Power Button [PWRF]
[    8.980131] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    8.980264] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0x8060
[    8.985088] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[    8.985209] sp5100_tco: PCI Revision ID: 0x42
[    8.985291] sp5100_tco: Using 0xfed80b00 for watchdog MMIO address
[    8.985305] sp5100_tco: Last reboot was not triggered by watchdog.
[    8.985650] sp5100_tco: initialized (0xf7e1cb00). heartbeat=60 sec (nowayout=0)
[    9.030231] [drm] Initialized drm 1.1.0 20060810
[    9.041356] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,discard
[    9.068520] snd_hda_intel 0000:00:01.1: irq 43 for MSI/MSI-X
[    9.116399] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    9.119886] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input7
[    9.163027] sound hdaudioC1D0: ALC892: SKU not ready 0x00000100
[    9.163471] sound hdaudioC1D0: autoconfig: line_outs=4 (0x14/0x16/0x15/0x17/0x0) type:line
[    9.163476] sound hdaudioC1D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    9.163486] sound hdaudioC1D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[    9.163490] sound hdaudioC1D0:    mono: mono_out=0x0
[    9.163494] sound hdaudioC1D0:    dig-out=0x1e/0x0
[    9.163498] sound hdaudioC1D0:    inputs:
[    9.163504] sound hdaudioC1D0:      Rear Mic=0x18
[    9.163509] sound hdaudioC1D0:      Front Mic=0x19
[    9.163513] sound hdaudioC1D0:      Line=0x1a
[    9.163517] sound hdaudioC1D0:      CD=0x1c
[    9.184146] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/sound/card1/hdaudioC1D0/input8
[    9.184567] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input9
[    9.184645] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[    9.184724] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
[    9.184804] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card1/input12
[    9.184880] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card1/input13
[    9.184957] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card1/input14
[    9.185029] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card1/input15
[    9.185102] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input16
[    9.412143] systemd-udevd[282]: renamed network interface eth0 to eth10
[    9.420845] [drm] radeon kernel modesetting enabled.
[    9.473054] [drm] initializing kernel modesetting (PALM 0x1002:0x9802 0x1002:0x9802).
[    9.473087] [drm] register mmio base: 0xF0100000
[    9.473090] [drm] register mmio size: 262144
[    9.473199] ATOM BIOS: AMD
[    9.473286] radeon 0000:00:01.0: VRAM: 384M 0x0000000000000000 - 0x0000000017FFFFFF (384M used)
[    9.473292] radeon 0000:00:01.0: GTT: 1024M 0x0000000018000000 - 0x0000000057FFFFFF
[    9.473297] [drm] Detected VRAM RAM=384M, BAR=256M
[    9.473300] [drm] RAM width 32bits DDR
[    9.481873] [TTM] Zone  kernel: Available graphics memory: 414588 kiB
[    9.481883] [TTM] Zone highmem: Available graphics memory: 3948586 kiB
[    9.481886] [TTM] Initializing pool allocator
[    9.481898] [TTM] Initializing DMA pool allocator
[    9.481943] [drm] radeon: 384M of VRAM memory ready
[    9.481947] [drm] radeon: 1024M of GTT memory ready.
[    9.481982] [drm] Loading PALM Microcode
[    9.530786] kvm: Nested Virtualization enabled
[    9.530837] kvm: Nested Paging enabled
[    9.584673] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/PALM_pfp.bin
[    9.599672] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/PALM_me.bin
[    9.645963] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/SUMO_rlc.bin
[    9.645983] [drm] Internal thermal controller without fan control
[    9.646291] [drm] Found smc ucode version: 0x00010601
[    9.662516] [drm] radeon: dpm initialized
[    9.710747] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/SUMO_uvd.bin
[    9.710877] [drm] GART: num cpu pages 262144, num gpu pages 262144
[    9.745591] [drm] PCIE GART of 1024M enabled (table at 0x0000000000273000).
[    9.758120] radeon 0000:00:01.0: WB enabled
[    9.758135] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000018000c00 and cpu addr 0xff6d4c00
[    9.758141] radeon 0000:00:01.0: fence driver on ring 3 use gpu addr 0x0000000018000c0c and cpu addr 0xff6d4c0c
[    9.760184] radeon 0000:00:01.0: fence driver on ring 5 use gpu addr 0x0000000000072118 and cpu addr 0xf8632118
[    9.761449] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    9.761454] [drm] Driver supports precise vblank timestamp query.
[    9.761461] radeon 0000:00:01.0: radeon: MSI limited to 32-bit
[    9.761499] radeon 0000:00:01.0: irq 44 for MSI/MSI-X
[    9.761524] radeon 0000:00:01.0: radeon: using MSI.
[    9.761566] [drm] radeon: irq initialized.
[    9.779990] [drm] ring test on 0 succeeded in 1 usecs
[    9.780009] [drm] ring test on 3 succeeded in 3 usecs
[    9.842257] [drm] ring test on 5 succeeded in 1 usecs
[    9.862542] [drm] UVD initialized successfully.
[    9.864101] [drm] ib test on ring 0 succeeded in 0 usecs
[    9.864149] [drm] ib test on ring 3 succeeded in 0 usecs
[    9.885387] [drm] ib test on ring 5 succeeded
[    9.922502] [drm] Radeon Display Connectors
[    9.922513] [drm] Connector 0:
[    9.922515] [drm]   HDMI-A-1
[    9.922518] [drm]   HPD1
[    9.922523] [drm]   DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[    9.922525] [drm]   Encoders:
[    9.922528] [drm]     DFP1: INTERNAL_UNIPHY
[    9.922531] [drm] Connector 1:
[    9.922533] [drm]   HDMI-A-2
[    9.922535] [drm]   HPD2
[    9.922539] [drm]   DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[    9.922541] [drm]   Encoders:
[    9.922544] [drm]     DFP2: INTERNAL_UNIPHY
[    9.922546] [drm] Connector 2:
[    9.922548] [drm]   VGA-1
[    9.922552] [drm]   DDC: 0x64d8 0x64d8 0x64dc 0x64dc 0x64e0 0x64e0 0x64e4 0x64e4
[    9.922554] [drm]   Encoders:
[    9.922556] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    9.970102] [drm] fb mappable at 0xE0477000
[    9.970112] [drm] vram apper at 0xE0000000
[    9.970115] [drm] size 5242880
[    9.970117] [drm] fb depth is 24
[    9.970120] [drm]    pitch is 5120
[    9.970310] fbcon: radeondrmfb (fb0) is primary device
[   10.011614] Console: switching to colour frame buffer device 160x64
[   10.021588] radeon 0000:00:01.0: fb0: radeondrmfb frame buffer device
[   10.021593] radeon 0000:00:01.0: registered panic notifier
[   10.038987] [drm] Initialized radeon 2.39.0 20080528 for 0000:00:01.0 on minor 0
[   10.060274] cfg80211: Calling CRDA to update world regulatory domain
[   10.310958] usb 2-2: reset high-speed USB device number 2 using ehci-pci
[   10.352802] cfg80211: World regulatory domain updated:
[   10.352816] cfg80211:  DFS Master region: unset
[   10.352820] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   10.352828] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.352833] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.352838] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   10.352844] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   10.352850] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   10.352855] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   10.352859] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.352864] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   10.393600] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: discard
[   10.452800] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0202 detected
[   10.465544] systemd-journald[223]: Received request to flush runtime journal from PID 1
[   10.507443] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0001 detected
[   10.535256] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   10.535962] usbcore: registered new interface driver rt2800usb
[   10.635090] systemd-udevd[276]: renamed network interface wlan0 to wlan1
[   11.151272] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[   11.152707] rt2800usb 2-2:1.0: firmware: direct-loading firmware rt2870.bin
[   11.152734] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[   11.366783] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   12.413927] r8169 0000:03:00.0: firmware: direct-loading firmware rtl_nic/rtl8168e-2.fw
[   12.550600] r8169 0000:03:00.0 eth10: link down
[   12.550776] IPv6: ADDRCONF(NETDEV_UP): eth10: link is not ready
[   35.718911] wlan1: authenticate with 34:31:c4:bd:c8:97
[   35.767208] wlan1: send auth to 34:31:c4:bd:c8:97 (try 1/3)
[   35.776706] wlan1: authenticated
[   35.779355] wlan1: associate with 34:31:c4:bd:c8:97 (try 1/3)
[   35.802105] wlan1: RX AssocResp from 34:31:c4:bd:c8:97 (capab=0x31 status=0 aid=2)
[   35.812320] wlan1: associated
[   35.812362] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   35.812698] cfg80211: Calling CRDA for country: DE
[   35.826975] cfg80211: Regulatory domain changed to country: DE
[   35.826988] cfg80211:  DFS Master region: ETSI
[   35.826992] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   35.826999] cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   35.827004] cfg80211:   (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   35.827010] cfg80211:   (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   35.827014] cfg80211:   (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2698 mBm), (0 s)
[   35.827018] cfg80211:   (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)