[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt7-1 (2015-03-01)
[    0.000000] Command line: root=/dev/nfs initrd=initrd-cb-test-tgt rootfstype=nfs nfsroot=10.100.1.100:/nfsroots/cb-test-tgt-01,v3,hard,nointr,tcp ip=10.100.1.10::10.100.1.1:255.255.255.0:embed-o-matic:eth0:off console=ttyS0,115200n8 consoleblank=0 rw BOOT_IMAGE=vmlinuz-cb-test-tgt 
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bff9afff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bff9b000-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: ASUS KFSN4-DRE/KFSN4-DRE, BIOS 4.2-410-gedf965a-dirty 11/27/2015
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] AGP: No AGP bridge found
[    0.000000] e820: last_pfn = 0x180000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-back
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000F4000000 mask FFFFFC000000 write-combining
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000180000000 aka 6144M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0xbff9b max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f1cf0-0x000f1cff] mapped at [ffff8800000f1cf0]
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01af3000, 0x01af3fff] PGTABLE
[    0.000000] BRK [0x01af4000, 0x01af4fff] PGTABLE
[    0.000000] BRK [0x01af5000, 0x01af5fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x17fe00000-0x17fffffff]
[    0.000000]  [mem 0x17fe00000-0x17fffffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x17c000000-0x17fdfffff]
[    0.000000]  [mem 0x17c000000-0x17fdfffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x100000000-0x17bffffff]
[    0.000000]  [mem 0x100000000-0x17bffffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x00100000-0xbff9afff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x3fffffff] page 2M
[    0.000000]  [mem 0x40000000-0x7fffffff] page 1G
[    0.000000]  [mem 0x80000000-0xbfdfffff] page 2M
[    0.000000]  [mem 0xbfe00000-0xbff9afff] page 4k
[    0.000000] RAMDISK: [mem 0x7f775000-0x7fffefff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F1EC0 000024 (v02 CORE  )
[    0.000000] ACPI: XSDT 0x00000000BFFB40E0 00006C (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: FACP 0x00000000BFFB68D0 000074 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: DSDT 0x00000000BFFB4280 002644 (v02 ASUS   COREBOOT 00000001 INTL 20150204)
[    0.000000] ACPI: FACS 0x00000000BFFB4240 000040
[    0.000000] ACPI: SSDT 0x00000000BFFB69D0 000EA6 (v02 CORE   COREBOOT 0000002A CORE 0000002A)
[    0.000000] ACPI: TCPA 0x00000000BFFB7880 000032 (v02 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: APIC 0x00000000BFFB78C0 0000C6 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SRAT 0x00000000BFFB7990 000150 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SLIT 0x00000000BFFB7AE0 000030 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: HPET 0x00000000BFFB7B10 000038 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SRAT 0x00000000BFFB7B50 000150 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SLIT 0x00000000BFFB7CA0 000030 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] SRAT: PXM 0 -> APIC 0x00 -> Node 0
[    0.000000] SRAT: PXM 0 -> APIC 0x01 -> Node 0
[    0.000000] SRAT: PXM 0 -> APIC 0x02 -> Node 0
[    0.000000] SRAT: PXM 0 -> APIC 0x03 -> Node 0
[    0.000000] SRAT: PXM 1 -> APIC 0x04 -> Node 1
[    0.000000] SRAT: PXM 1 -> APIC 0x05 -> Node 1
[    0.000000] SRAT: PXM 1 -> APIC 0x06 -> Node 1
[    0.000000] SRAT: PXM 1 -> APIC 0x07 -> Node 1
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x00000000-0x0009ffff]
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x00100000-0xbfffffff]
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x100000000-0x13fffffff]
[    0.000000] SRAT: Node 1 PXM 1 [mem 0x140000000-0x17fffffff]
[    0.000000] NUMA: Initialized distance table, cnt=2
[    0.000000] NUMA: Node 0 [mem 0x00000000-0x0009ffff] + [mem 0x00100000-0xbfffffff] -> [mem 0x00000000-0xbfffffff]
[    0.000000] NUMA: Node 0 [mem 0x00000000-0xbfffffff] + [mem 0x100000000-0x13fffffff] -> [mem 0x00000000-0x13fffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x13fffffff]
[    0.000000]   NODE_DATA [mem 0x13fffb000-0x13fffffff]
[    0.000000] Initmem setup node 1 [mem 0x140000000-0x17fffffff]
[    0.000000]   NODE_DATA [mem 0x17fff8000-0x17fffcfff]
[    0.000000]  [ffffea0000000000-ffffea00045fffff] PMD -> [ffff88013be00000-ffff88013f5fffff] on node 0
[    0.000000]  [ffffea0004600000-ffffea00053fffff] PMD -> [ffff88017e600000-ffff88017f3fffff] on node 1
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x17fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0xbff9afff]
[    0.000000]   node   0: [mem 0x100000000-0x13fffffff]
[    0.000000]   node   1: [mem 0x140000000-0x17fffffff]
[    0.000000] On node 0 totalpages: 1048377
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10695 pages used for memmap
[    0.000000]   DMA32 zone: 782235 pages, LIFO batch:31
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 262144 pages, LIFO batch:31
[    0.000000] On node 1 totalpages: 262144
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 262144 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x2008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x18] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 24, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[    0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xbff9b000-0xcfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xffffffff]
[    0.000000] e820: [mem 0xd0000000-0xffffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:8 nr_node_ids:2
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88013fc00000 s80896 r8192 d21504 u524288
[    0.000000] pcpu-alloc: s80896 r8192 d21504 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 [1] 4 5 6 7 
[    0.000000] Built 2 zonelists in Node order, mobility grouping on.  Total pages: 1292581
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=/dev/nfs initrd=initrd-cb-test-tgt rootfstype=nfs nfsroot=10.100.1.100:/nfsroots/cb-test-tgt-01,v3,hard,nointr,tcp ip=10.100.1.10::10.100.1.1:255.255.255.0:embed-o-matic:eth0:off console=ttyS0,115200n8 consoleblank=0 rw BOOT_IMAGE=vmlinuz-cb-test-tgt 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] AGP: Node 0: aperture [bus addr 0xf8000000-0xfbffffff] (64MB)
[    0.000000] AGP: Node 1: aperture [bus addr 0xf8000000-0xfbffffff] (64MB)
[    0.000000] Memory: 5083036K/5242084K available (5203K kernel code, 943K rwdata, 1832K rodata, 1204K init, 840K bss, 159048K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=8.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS:33024 nr_irqs:744 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [ttyS0] enabled
[    0.000000] mempolicy: Disabling automatic NUMA balancing. Configure with numa_balancing= or the kernel.numa_balancing sysctl
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1909.804 MHz processor
[    0.000157] Calibrating delay loop (skipped), value calculated using timer frequency.. 3819.60 BogoMIPS (lpj=7639216)
[    0.010795] pid_max: default: 32768 minimum: 301
[    0.015450] ACPI: Core revision 20140424
[    0.021807] ACPI: All ACPI Tables successfully acquired
[    0.027172] Security Framework initialized
[    0.031297] AppArmor: AppArmor disabled by boot time parameter
[    0.037132] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.044883] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.058107] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.067870] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.074771] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.082623] Initializing cgroup subsys memory
[    0.087002] Initializing cgroup subsys devices
[    0.091463] Initializing cgroup subsys freezer
[    0.095926] Initializing cgroup subsys net_cls
[    0.100383] Initializing cgroup subsys blkio
[    0.104679] Initializing cgroup subsys perf_event
[    0.109398] Initializing cgroup subsys net_prio
[    0.113977] tseg: 0000000000
[    0.113988] CPU: Physical Processor ID: 0
[    0.118016] CPU: Processor Core ID: 0
[    0.121706] mce: CPU supports 6 MCE banks
[    0.125734] LVT offset 0 assigned for vector 0xf9
[    0.130464] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8
Last level dTLB entries: 4KB 512, 2MB 128, 4MB 64, 1GB 0
tlb_flushall_shift: 6
[    0.145813] Freeing SMP alternatives memory: 20K (ffffffff81a1a000 - ffffffff81a1f000)
[    0.154819] ftrace: allocating 21601 entries in 85 pages
[    0.170202] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=0 pin2=0
[    0.215727] smpboot: CPU0: Quad-Core AMD Opteron(tm) Processor 8347 (fam: 10, model: 02, stepping: 01)
[    0.332510] Performance Events: AMD PMU driver.
[    0.337079] ... version:                0
[    0.341093] ... bit width:              48
[    0.345194] ... generic registers:      4
[    0.349211] ... value mask:             0000ffffffffffff
[    0.354521] ... max period:             00007fffffffffff
[    0.359832] ... fixed-purpose events:   0
[    0.363861] ... event mask:             000000000000000f
[    0.371778] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.379978] x86: Booting SMP configuration:
[    0.384174] .... node  #0, CPUs:      #1 #2 #3
[    0.428519] .... node  #1, CPUs:   #4 #5 #6 #7
[    0.581110] x86: Booted up 2 nodes, 8 CPUs
[    0.585412] smpboot: Total of 8 processors activated (30557.62 BogoMIPS)
[    0.597924] devtmpfs: initialized
[    0.609831] pinctrl core: initialized pinctrl subsystem
[    0.615230] NET: Registered protocol family 16
[    0.619894] cpuidle: using governor ladder
[    0.624001] cpuidle: using governor menu
[    0.627938] node 0 link 1: io port [1000, 3fff]
[    0.627942] TOM: 00000000c0000000 aka 3072M
[    0.632135] Fam 10h mmconf [mem 0xc0000000-0xcfffffff]
[    0.632139] node 0 link 1: mmio [fc000000, fc3fffff]
[    0.632142] node 0 link 1: mmio [f4000000, f7ffffff]
[    0.632145] TOM2: 0000000180000000 aka 6144M
[    0.636422] bus: [bus 00-05] on node 0 link 1
[    0.636424] bus: 00 [io  0x0000-0xffff]
[    0.636425] bus: 00 [mem 0xf8000000-0xffffffff]
[    0.636427] bus: 00 [mem 0xd0000000-0xf7ffffff]
[    0.636428] bus: 00 [mem 0x180000000-0xfcffffffff]
[    0.636534] ACPI: bus type PCI registered
[    0.640547] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.647155] PCI: Using configuration type 1 for base access
[    0.652727] PCI: Using configuration type 1 for extended access
[    0.669320] ACPI: Added _OSI(Module Device)
[    0.673514] ACPI: Added _OSI(Processor Device)
[    0.677965] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.682675] ACPI: Added _OSI(Processor Aggregator Device)
[    0.691692] ACPI: Interpreter enabled
[    0.695374] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[    0.704638] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20140424/hwxface-580)
[    0.713903] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S4_] (20140424/hwxface-580)
[    0.723181] ACPI: (supports S0 S1 S5)
[    0.726852] ACPI: Using IOAPIC for interrupt routing
[    0.731863] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.760056] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-05])
[    0.766246] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.774455] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.811376] acpi PNP0A03:00: host bridge window expanded to [io  0x0000-0x0cf7]; [io  0x03b0-0x03df] ignored
[    0.821427] PCI host bridge to bus 0000:00
[    0.825535] pci_bus 0000:00: root bus resource [bus 00-05]
[    0.831025] pci_bus 0000:00: root bus resource [io  0x0d00-0x3fff]
[    0.837212] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.844090] pci_bus 0000:00: root bus resource [mem 0xf4000000-0xf7ffffff]
[    0.850959] pci_bus 0000:00: root bus resource [mem 0xfc000000-0xfc3fffff]
[    0.857830] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.864029] pci 0000:00:00.0: [10de:005e] type 00 class 0x058000
[    0.864220] pci 0000:00:01.0: [10de:0051] type 00 class 0x060100
[    0.864227] pci 0000:00:01.0: reg 0x10: [io  0x2c00-0x2c7f]
[    0.864364] pci 0000:00:01.1: [10de:0052] type 00 class 0x0c0500
[    0.864375] pci 0000:00:01.1: reg 0x10: [io  0x3000-0x301f]
[    0.864394] pci 0000:00:01.1: reg 0x20: [io  0x2c80-0x2cbf]
[    0.864413] pci 0000:00:01.1: reg 0x24: [io  0x2cc0-0x2cff]
[    0.864440] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.864561] pci 0000:00:02.0: [10de:005a] type 00 class 0x0c0310
[    0.864585] pci 0000:00:02.0: reg 0x10: [mem 0xfc300000-0xfc300fff]
[    0.864622] pci 0000:00:02.0: supports D1 D2
[    0.864625] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.864685] pci 0000:00:02.0: System wakeup disabled by ACPI
[    0.870409] pci 0000:00:02.1: [10de:005b] type 00 class 0x0c0320
[    0.870418] pci 0000:00:02.1: reg 0x10: [mem 0xfc303000-0xfc3030ff]
[    0.870452] pci 0000:00:02.1: supports D1 D2
[    0.870454] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.870507] pci 0000:00:02.1: System wakeup disabled by ACPI
[    0.876236] pci 0000:00:06.0: [10de:0053] type 00 class 0x01018a
[    0.876262] pci 0000:00:06.0: reg 0x20: [io  0x3020-0x302f]
[    0.876289] pci 0000:00:06.0: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.883423] pci 0000:00:06.0: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.889945] pci 0000:00:06.0: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.897077] pci 0000:00:06.0: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.903721] pci 0000:00:07.0: [10de:0054] type 00 class 0x010185
[    0.903737] pci 0000:00:07.0: reg 0x10: [io  0x3050-0x3057]
[    0.903742] pci 0000:00:07.0: reg 0x14: [io  0x3070-0x3073]
[    0.903746] pci 0000:00:07.0: reg 0x18: [io  0x3058-0x305f]
[    0.903751] pci 0000:00:07.0: reg 0x1c: [io  0x3074-0x3077]
[    0.903756] pci 0000:00:07.0: reg 0x20: [io  0x3030-0x303f]
[    0.903760] pci 0000:00:07.0: reg 0x24: [mem 0xfc301000-0xfc301fff]
[    0.903927] pci 0000:00:08.0: [10de:0055] type 00 class 0x010185
[    0.903934] pci 0000:00:08.0: reg 0x10: [io  0x3060-0x3067]
[    0.903939] pci 0000:00:08.0: reg 0x14: [io  0x3078-0x307b]
[    0.903944] pci 0000:00:08.0: reg 0x18: [io  0x3068-0x306f]
[    0.903948] pci 0000:00:08.0: reg 0x1c: [io  0x307c-0x307f]
[    0.903953] pci 0000:00:08.0: reg 0x20: [io  0x3040-0x304f]
[    0.903958] pci 0000:00:08.0: reg 0x24: [mem 0xfc302000-0xfc302fff]
[    0.904113] pci 0000:00:09.0: [10de:005c] type 01 class 0x060400
[    0.904197] pci 0000:00:09.0: System wakeup disabled by ACPI
[    0.909917] pci 0000:00:0b.0: [10de:005d] type 01 class 0x060400
[    0.909966] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.910027] pci 0000:00:0b.0: System wakeup disabled by ACPI
[    0.915744] pci 0000:00:0c.0: [10de:005d] type 01 class 0x060400
[    0.915799] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.915856] pci 0000:00:0c.0: System wakeup disabled by ACPI
[    0.921580] pci 0000:00:0d.0: [10de:005d] type 01 class 0x060400
[    0.921630] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.921695] pci 0000:00:0d.0: System wakeup disabled by ACPI
[    0.927419] pci 0000:00:0e.0: [10de:005d] type 01 class 0x060400
[    0.927472] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.927526] pci 0000:00:0e.0: System wakeup disabled by ACPI
[    0.933256] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000
[    0.933395] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000
[    0.933551] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000
[    0.933683] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000
[    0.933812] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000
[    0.933928] pci 0000:00:19.0: [1022:1200] type 00 class 0x060000
[    0.934072] pci 0000:00:19.1: [1022:1201] type 00 class 0x060000
[    0.934201] pci 0000:00:19.2: [1022:1202] type 00 class 0x060000
[    0.934337] pci 0000:00:19.3: [1022:1203] type 00 class 0x060000
[    0.934472] pci 0000:00:19.4: [1022:1204] type 00 class 0x060000
[    0.934658] pci 0000:01:04.0: [18ca:0020] type 00 class 0x030000
[    0.934678] pci 0000:01:04.0: reg 0x10: [mem 0xf4000000-0xf7ffffff pref]
[    0.934697] pci 0000:01:04.0: reg 0x14: [mem 0xfc000000-0xfc03ffff]
[    0.934710] pci 0000:01:04.0: reg 0x18: [io  0x1000-0x107f]
[    0.934762] pci 0000:01:04.0: supports D1 D2
[    0.934838] pci 0000:00:09.0: PCI bridge to [bus 01]
[    0.939826] pci 0000:00:09.0:   bridge window [io  0x1000-0x1fff]
[    0.939829] pci 0000:00:09.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    0.939833] pci 0000:00:09.0:   bridge window [mem 0xf4000000-0xf7ffffff pref]
[    0.939952] pci 0000:02:00.0: [14e4:1659] type 00 class 0x020000
[    0.939986] pci 0000:02:00.0: reg 0x10: [mem 0xfc100000-0xfc10ffff 64bit]
[    0.940030] pci 0000:02:00.0: reg 0x30: [mem 0x7be00000-0x7be0ffff pref]
[    0.940122] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.940224] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.950226] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    0.955195] pci 0000:00:0b.0:   bridge window [mem 0xfc100000-0xfc1fffff]
[    0.955301] pci 0000:03:00.0: [14e4:1659] type 00 class 0x020000
[    0.955339] pci 0000:03:00.0: reg 0x10: [mem 0xfc200000-0xfc20ffff 64bit]
[    0.955450] pci 0000:03:00.0: PME# supported from D3hot D3cold
[    0.955527] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.965526] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    0.970495] pci 0000:00:0c.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    0.970570] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    0.975608] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    0.980594] pci_bus 0000:00: on NUMA node 0
[    0.980695] ACPI: PCI Interrupt Link [LNKA] (IRQs *16 17 18 19)
[    0.986852] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 *17 18 19)
[    0.993028] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[    1.000332] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[    1.007641] ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled.
[    1.014944] ACPI: PCI Interrupt Link [LLAS] (IRQs 20 21 22 23) *0, disabled.
[    1.022237] ACPI: PCI Interrupt Link [LUOH] (IRQs 20 21 22 *23)
[    1.028360] ACPI: PCI Interrupt Link [LUEH] (IRQs 20 21 *22 23)
[    1.034497] ACPI: PCI Interrupt Link [LAUD] (IRQs 20 21 22 23) *0, disabled.
[    1.041801] ACPI: PCI Interrupt Link [LMOD] (IRQs 20 21 22 23) *0, disabled.
[    1.049102] ACPI: PCI Interrupt Link [LPA0] (IRQs 20 21 22 23) *0, disabled.
[    1.056398] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 *21 22 23)
[    1.062530] ACPI: PCI Interrupt Link [LSA1] (IRQs *20 21 22 23)
[    1.068670] ACPI: PCI Interrupt Link [LEMA] (IRQs 20 21 22 23) *0, disabled.
[    1.075966] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *0, disabled.
[    1.083280] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *0, disabled.
[    1.090582] ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    1.099145] ACPI: PCI Interrupt Link [LNIA] (IRQs 16) *0, disabled.
[    1.105609] ACPI: PCI Interrupt Link [LNIB] (IRQs 17) *0, disabled.
[    1.112092] ACPI: PCI Interrupt Link [LNIC] (IRQs 18) *0, disabled.
[    1.118560] ACPI: PCI Interrupt Link [LNND] (IRQs 19) *0, disabled.
[    1.125285] ACPI: Enabled 1 GPEs in block 00 to 1F
[    1.130398] vgaarb: setting as boot device: PCI:0000:01:04.0
[    1.136064] vgaarb: device added: PCI:0000:01:04.0,decodes=io+mem,owns=io+mem,locks=none
[    1.144160] vgaarb: loaded
[    1.146876] vgaarb: bridge control possible 0000:01:04.0
[    1.152364] PCI: Using ACPI for IRQ routing
[    1.156559] PCI: pci_cache_line_size set to 64 bytes
[    1.156615] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    1.156619] e820: reserve RAM buffer [mem 0xbff9b000-0xbfffffff]
[    1.156952] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    1.164009] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    1.169070] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    1.177751] Switched to clocksource hpet
[    1.193362] pnp: PnP ACPI init
[    1.196486] ACPI: bus type PNP registered
[    1.201026] pnp 00:00: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    1.201114] pnp 00:01: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[    1.201198] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.201295] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.201334] pnp 00:04: [dma 2]
[    1.201381] pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
[    1.201403] pnp: PnP ACPI: found 5 devices
[    1.205512] ACPI: bus type PNP unregistered
[    1.217534] pci 0000:02:00.0: can't claim BAR 6 [mem 0x7be00000-0x7be0ffff pref]: no compatible bridge window
[    1.227483] pci 0000:00:09.0: PCI bridge to [bus 01]
[    1.232460] pci 0000:00:09.0:   bridge window [io  0x1000-0x1fff]
[    1.238561] pci 0000:00:09.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    1.245351] pci 0000:00:09.0:   bridge window [mem 0xf4000000-0xf7ffffff pref]
[    1.252584] pci 0000:02:00.0: BAR 6: assigned [mem 0xfc110000-0xfc11ffff pref]
[    1.259811] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    1.264784] pci 0000:00:0b.0:   bridge window [mem 0xfc100000-0xfc1fffff]
[    1.271578] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    1.276547] pci 0000:00:0c.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    1.283342] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    1.288322] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    1.293299] pci_bus 0000:00: resource 4 [io  0x0d00-0x3fff]
[    1.293302] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[    1.293304] pci_bus 0000:00: resource 6 [mem 0xf4000000-0xf7ffffff]
[    1.293307] pci_bus 0000:00: resource 7 [mem 0xfc000000-0xfc3fffff]
[    1.293309] pci_bus 0000:00: resource 8 [io  0x0000-0x0cf7]
[    1.293312] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]
[    1.293315] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfc0fffff]
[    1.293317] pci_bus 0000:01: resource 2 [mem 0xf4000000-0xf7ffffff pref]
[    1.293321] pci_bus 0000:02: resource 1 [mem 0xfc100000-0xfc1fffff]
[    1.293324] pci_bus 0000:03: resource 1 [mem 0xfc200000-0xfc2fffff]
[    1.293480] NET: Registered protocol family 2
[    1.298375] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    1.306076] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    1.313422] TCP: Hash tables configured (established 65536 bind 65536)
[    1.320022] TCP: reno registered
[    1.323280] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    1.329489] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    1.336277] NET: Registered protocol family 1
[    1.341028] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[    1.347108] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[    1.353009] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.358550] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.364045] pci 0000:00:0b.0: Found disabled HT MSI Mapping
[    1.369632] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.375168] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.380677] pci 0000:00:0c.0: Found disabled HT MSI Mapping
[    1.386267] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.391804] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.397311] pci 0000:00:0d.0: Found disabled HT MSI Mapping
[    1.402896] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.408445] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.413954] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[    1.419538] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.425067] pci 0000:01:04.0: Video device with shadowed ROM
[    1.425076] PCI: CLS 64 bytes, default 64
[    1.425183] Unpacking initramfs...
[    1.658431] Freeing initrd memory: 8744K (ffff88007f775000 - ffff88007ffff000)
[    1.666291] PCI-DMA: Disabling AGP.
[    1.671379] PCI-DMA: aperture base @ f8000000 size 65536 KB
[    1.676962] init_memory_mapping: [mem 0xf8000000-0xfbffffff]
[    1.682624]  [mem 0xf8000000-0xfbffffff] page 2M
[    1.682647] PCI-DMA: using GART IOMMU.
[    1.686415] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    1.698780] platform rtc_cmos: registered platform RTC device (no PNP device found)
[    1.706962] microcode: CPU0: patch_level=0x01000084
[    1.711849] microcode: CPU1: patch_level=0x01000084
[    1.716744] microcode: CPU2: patch_level=0x01000084
[    1.721646] microcode: CPU3: patch_level=0x01000084
[    1.726551] microcode: CPU4: patch_level=0x01000084
[    1.731443] microcode: CPU5: patch_level=0x01000084
[    1.736344] microcode: CPU6: patch_level=0x01000084
[    1.741240] microcode: CPU7: patch_level=0x01000084
[    1.746233] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.755033] LVT offset 1 assigned for vector 0x400
[    1.759843] IBS: LVT offset 1 assigned
[    1.763634] perf: AMD IBS detected (0x00000007)
[    1.768777] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    1.775161] audit: initializing netlink subsys (disabled)
[    1.780589] audit: type=2000 audit(1448647709.516:1): initialized
[    1.787470] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.793876] zbud: loaded
[    1.796771] VFS: Disk quotas dquot_6.5.2
[    1.800732] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.807286] msgmni has been set to 10073
[    1.811773] alg: No test for stdrng (krng)
[    1.815936] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.823443] io scheduler noop registered
[    1.827378] io scheduler deadline registered
[    1.831731] io scheduler cfq registered (default)
[    1.836655] pcieport 0000:00:0b.0: irq 40 for MSI/MSI-X
[    1.836780] pcieport 0000:00:0c.0: irq 41 for MSI/MSI-X
[    1.836913] pcieport 0000:00:0d.0: irq 42 for MSI/MSI-X
[    1.837027] pcieport 0000:00:0e.0: irq 43 for MSI/MSI-X
[    1.837192] aer 0000:00:0b.0:pcie02: service driver aer loaded
[    1.837216] aer 0000:00:0c.0:pcie02: service driver aer loaded
[    1.837242] aer 0000:00:0d.0:pcie02: service driver aer loaded
[    1.837267] aer 0000:00:0e.0:pcie02: service driver aer loaded
[    1.837287] pcieport 0000:00:0b.0: Signaling PME through PCIe PME interrupt
[    1.844260] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[    1.850793] pcie_pme 0000:00:0b.0:pcie01: service driver pcie_pme loaded
[    1.850804] pcieport 0000:00:0c.0: Signaling PME through PCIe PME interrupt
[    1.857768] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[    1.864299] pcie_pme 0000:00:0c.0:pcie01: service driver pcie_pme loaded
[    1.864308] pcieport 0000:00:0d.0: Signaling PME through PCIe PME interrupt
[    1.871274] pcie_pme 0000:00:0d.0:pcie01: service driver pcie_pme loaded
[    1.871286] pcieport 0000:00:0e.0: Signaling PME through PCIe PME interrupt
[    1.878250] pcie_pme 0000:00:0e.0:pcie01: service driver pcie_pme loaded
[    1.878279] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.883885] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.890624] GHES: HEST is not enabled!
[    1.894507] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.921099] 00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.948784] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[    1.956718] Linux agpgart interface v0.103
[    1.961032] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f03:MOU] at 0x60,0x64 irq 1,12
[    1.971537] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.976526] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.981820] mousedev: PS/2 mouse device common for all mice
[    1.987493] rtc_cmos rtc_cmos: RTC can wake from S4
[    1.992599] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[    1.998999] rtc_cmos rtc_cmos: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    2.006867] ledtrig-cpu: registered to indicate activity on CPUs
[    2.013140] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[    2.019591] AMD IOMMUv2 functionality not available on this system
[    2.025953] TCP: cubic registered
[    2.029416] NET: Registered protocol family 10
[    2.034257] mip6: Mobile IPv6
[    2.035707] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    2.045844] NET: Registered protocol family 17
[    2.050305] mpls_gso: MPLS GSO support
[    2.054912] registered taskstats version 1
[    2.059765] rtc_cmos rtc_cmos: setting system clock to 2015-11-27 18:08:30 UTC (1448647710)
[    2.068183] PM: Hibernation image not present or could not be loaded.
[    2.070008] Freeing unused kernel memory: 1204K (ffffffff818ed000 - ffffffff81a1a000)
[    2.077845] Write protecting the kernel read-only data: 8192k
[    2.087081] Freeing unused kernel memory: 928K (ffff880001518000 - ffff880001600000)
[    2.095675] Freeing unused kernel memory: 216K (ffff8800017ca000 - ffff880001800000)
[    2.119576] systemd-udevd[99]: starting version 215
[    2.125346] random: systemd-udevd urandom read with 3 bits of entropy available
[    2.155295] ACPI: bus type USB registered
[    2.159514] usbcore: registered new interface driver usbfs
[    2.165097] usbcore: registered new interface driver hub
[    2.170637] usbcore: registered new device driver usb
[    2.170722] pps_core: LinuxPPS API ver. 1 registered
[    2.170723] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.190500] PTP clock support registered
[    2.194732] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.201684] tg3.c:v3.137 (May 11, 2014)
[    2.205584] tg3 0000:02:00.0: enabling device (0004 -> 0006)
[    2.211417] ehci-pci: EHCI PCI platform driver
[    2.211506] ACPI: PCI Interrupt Link [LNIB] enabled at IRQ 17
[    2.221884] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.221971] ehci-pci 0000:00:02.1: EHCI Host Controller
[    2.221988] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 1
[    2.222007] ehci-pci 0000:00:02.1: debug port 1
[    2.222052] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[    2.222081] ehci-pci 0000:00:02.1: irq 22, io mem 0xfc303000
[    2.233419] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    2.233485] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.233487] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.233488] usb usb1: Product: EHCI Host Controller
[    2.233490] usb usb1: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    2.233491] usb usb1: SerialNumber: 0000:00:02.1
[    2.233845] hub 1-0:1.0: USB hub found
[    2.233856] hub 1-0:1.0: 10 ports detected
[    2.294871] ohci-pci: OHCI PCI platform driver
[    2.299567] ohci-pci 0000:00:02.0: OHCI PCI host controller
[    2.305411] ohci-pci 0000:00:02.0: new USB bus registered, assigned bus number 2
[    2.312864] ohci-pci 0000:00:02.0: irq 23, io mem 0xfc300000
[    2.325684] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM95721) rev 4201] (PCI Express) MAC address 00:1e:8c:51:61:a2
[    2.335943] tg3 0000:02:00.0 eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    2.345680] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.353511] tg3 0000:02:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.360366] tg3 0000:03:00.0: enabling device (0004 -> 0006)
[    2.366180] ACPI: PCI Interrupt Link [LNIA] enabled at IRQ 16
[    2.375540] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.382341] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.389571] usb usb2: Product: OHCI PCI host controller
[    2.394802] usb usb2: Manufacturer: Linux 3.16.0-4-amd64 ohci_hcd
[    2.400900] usb usb2: SerialNumber: 0000:00:02.0
[    2.405754] hub 2-0:1.0: USB hub found
[    2.409528] hub 2-0:1.0: 10 ports detected
[    2.449718] tg3 0000:03:00.0 eth1: Tigon3 [partno(BCM95721) rev 4201] (PCI Express) MAC address 00:1e:8c:51:63:95
[    2.459986] tg3 0000:03:00.0 eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    2.469727] tg3 0000:03:00.0 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.477559] tg3 0000:03:00.0 eth1: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.491696] FS-Cache: Loaded
[    2.498201] RPC: Registered named UNIX socket transport module.
[    2.504837] RPC: Registered udp transport module.
[    2.510931] RPC: Registered tcp transport module.
[    2.517022] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.529424] FS-Cache: Netfs 'nfs' registered for caching
[    2.547566] tg3 0000:02:00.0: irq 44 for MSI/MSI-X
[    2.593399] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    2.697245] tsc: Refined TSC clocksource calibration: 1909.786 MHz
[    3.701006] Switched to clocksource tsc
[    4.184519] tg3 0000:02:00.0 eth0: Link is up at 100 Mbps, full duplex
[    4.191045] tg3 0000:02:00.0 eth0: Flow control is on for TX and on for RX
[    4.197930] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    5.058495] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    5.072519] systemd[1]: Detected architecture 'x86-64'.
[    5.290116] systemd[1]: Inserted module 'autofs4'
[    5.296262] systemd[1]: Set hostname to <cb-test-tgt>.
[    5.382653] random: nonblocking pool is initialized
[    5.547286] systemd[1]: Cannot add dependency job for unit dbus.socket, ignoring: Unit dbus.socket failed to load: No such file or directory.
[    5.560015] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    5.575410] systemd[1]: Expecting device dev-ttyS0.device...
[    5.588376] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    5.596146] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    5.603755] systemd[1]: Starting Remote File Systems (Pre).
[    5.620287] systemd[1]: Reached target Remote File Systems (Pre).
[    5.626409] systemd[1]: Starting Encrypted Volumes.
[    5.640263] systemd[1]: Reached target Encrypted Volumes.
[    5.645736] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    5.668254] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    5.677683] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[    5.685743] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    5.693671] systemd[1]: Starting Paths.
[    5.708241] systemd[1]: Reached target Paths.
[    5.712636] systemd[1]: Starting Swap.
[    5.724239] systemd[1]: Reached target Swap.
[    5.728538] systemd[1]: Starting Root Slice.
[    5.740257] systemd[1]: Created slice Root Slice.
[    5.744979] systemd[1]: Starting User and Session Slice.
[    5.760311] systemd[1]: Created slice User and Session Slice.
[    5.766131] systemd[1]: Starting Delayed Shutdown Socket.
[    5.780213] systemd[1]: Listening on Delayed Shutdown Socket.
[    5.785985] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[    5.804225] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    5.811205] systemd[1]: Starting Journal Socket (/dev/log).
[    5.828204] systemd[1]: Listening on Journal Socket (/dev/log).
[    5.834172] systemd[1]: Starting udev Kernel Socket.
[    5.848285] systemd[1]: Listening on udev Kernel Socket.
[    5.853686] systemd[1]: Starting udev Control Socket.
[    5.868175] systemd[1]: Listening on udev Control Socket.
[    5.873622] systemd[1]: Starting Journal Socket.
[    5.888170] systemd[1]: Listening on Journal Socket.
[    5.893185] systemd[1]: Starting System Slice.
[    5.908160] systemd[1]: Created slice System Slice.
[    5.913064] systemd[1]: Starting system-getty.slice.
[    5.928169] systemd[1]: Created slice system-getty.slice.
[    5.933589] systemd[1]: Starting system-serial\x2dgetty.slice.
[    5.948161] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    5.954488] systemd[1]: Starting Increase datagram queue length...
[    5.973668] systemd[1]: Starting udev Coldplug all Devices...
[    6.197196] systemd[1]: Starting Load Kernel Modules...
[    6.224269] systemd[1]: Started Set Up Additional Binary Formats.
[    6.230701] systemd[1]: Mounting Debug File System...
[    6.245900] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    6.270067] systemd[1]: Mounting POSIX Message Queue File System...
[    6.289996] systemd[1]: Mounting Huge Pages File System...
[    6.305566] systemd[1]: Starting Slices.
[    6.320108] systemd[1]: Reached target Slices.
[    6.324648] systemd[1]: Starting Remount Root and Kernel File Systems...
[    6.352070] systemd[1]: Mounted Huge Pages File System.
[    6.368081] systemd[1]: Mounted POSIX Message Queue File System.
[    6.384007] systemd[1]: Mounted Debug File System.
[    6.400037] systemd[1]: Started Increase datagram queue length.
[    6.416061] systemd[1]: Started Load Kernel Modules.
[    6.436045] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    6.459980] systemd[1]: Started Remount Root and Kernel File Systems.
[    6.476037] systemd[1]: Started udev Coldplug all Devices.
[    6.522138] systemd[1]: Started Various fixups to make systemd work better on Debian.
[    6.530027] systemd[1]: Starting Load/Save Random Seed...
[    6.545710] systemd[1]: Starting Create Static Device Nodes in /dev...
[    6.565491] systemd[1]: Starting Apply Kernel Variables...
[    6.581957] systemd[1]: Mounted Configuration File System.
[    6.587760] systemd[1]: Mounted FUSE Control File System.
[    6.593315] systemd[1]: Starting Syslog Socket.
[    6.607983] systemd[1]: Listening on Syslog Socket.
[    6.612938] systemd[1]: Starting Sockets.
[    6.623973] systemd[1]: Reached target Sockets.
[    6.628577] systemd[1]: Starting Journal Service...
[    6.655983] systemd[1]: Started Journal Service.
[    6.792281] systemd-udevd[189]: starting version 215
[    7.060546] systemd-journald[188]: Received request to flush runtime journal from PID 1
[    7.521006] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    7.555802] SCSI subsystem initialized
[    7.562429] EDAC MC: Ver: 3.0.0
[    7.565992] k10temp 0000:00:18.3: unreliable CPU thermal sensor; monitoring disabled
[    7.573859] k10temp 0000:00:19.3: unreliable CPU thermal sensor; monitoring disabled
[    7.617481] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    7.625881] ACPI: Power Button [PWRB]
[    7.629756] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    7.637194] ACPI: Power Button [PWRF]
[    7.641864] MCE: In-kernel MCE decoding enabled.
[    7.642034] i2c i2c-0: nForce2 SMBus adapter at 0x2c80
[    7.642061] i2c i2c-1: nForce2 SMBus adapter at 0x2cc0
[    7.672624] libata version 3.00 loaded.
[    7.675561] FDC 0 is a post-1991 82077
[    7.679919] acpi-cpufreq: overriding BIOS provided _PSD data
[    7.680092] input: PC Speaker as /devices/platform/pcspkr/input/input4
[    7.693067] pata_amd 0000:00:06.0: version 0.4.1
[    7.694050] scsi0 : pata_amd
[    7.694095] AMD64 EDAC driver v3.4.0
[    7.701032] scsi1 : pata_amd
[    7.704035] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x3020 irq 14
[    7.710998] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x3028 irq 15
[    7.718037] EDAC amd64: DRAM ECC enabled.
[    7.722163] EDAC amd64: F10h detected (node 0).
[    7.726735] EDAC MC: DCT0 chip selects:
[    7.726737] EDAC amd64: MC: 0:     0MB 1:     0MB
[    7.731444] EDAC amd64: MC: 2:     0MB 3:     0MB
[    7.736144] EDAC amd64: MC: 4:     0MB 5:     0MB
[    7.740858] EDAC amd64: MC: 6:  1024MB 7:  1024MB
[    7.745571] EDAC MC: DCT1 chip selects:
[    7.745573] EDAC amd64: MC: 0:     0MB 1:     0MB
[    7.750275] EDAC amd64: MC: 2:     0MB 3:     0MB
[    7.754984] EDAC amd64: MC: 4:     0MB 5:     0MB
[    7.759712] EDAC amd64: MC: 6:  1024MB 7:  1024MB
[    7.764444] EDAC amd64: using x4 syndromes.
[    7.768652] EDAC amd64: MCT channel count: 2
[    7.773024] EDAC amd64: CS6: Registered DDR2 RAM
[    7.777653] EDAC amd64: CS7: Registered DDR2 RAM
[    7.782828] EDAC MC0: Giving out device to module amd64_edac controller F10h: DEV 0000:00:18.2 (INTERRUPT)
[    7.792627] EDAC amd64: DRAM ECC enabled.
[    7.796814] EDAC amd64: F10h detected (node 1).
[    7.801457] EDAC MC: DCT0 chip selects:
[    7.801461] EDAC amd64: MC: 0:  1024MB 1:     0MB
[    7.806204] EDAC amd64: MC: 2:     0MB 3:     0MB
[    7.810944] EDAC amd64: MC: 4:     0MB 5:     0MB
[    7.815688] EDAC amd64: MC: 6:     0MB 7:     0MB
[    7.820521] EDAC MC: DCT1 chip selects:
[    7.820524] EDAC amd64: MC: 0:     0MB 1:     0MB
[    7.826630] EDAC amd64: MC: 2:     0MB 3:     0MB
[    7.832734] EDAC amd64: MC: 4:     0MB 5:     0MB
[    7.838408] EDAC amd64: MC: 6:     0MB 7:     0MB
[    7.843165] EDAC amd64: using x4 syndromes.
[    7.847400] EDAC amd64: MCT channel count: 1
[    7.851808] EDAC amd64: CS0: Registered DDR2 RAM
[    7.856923] EDAC MC1: Giving out device to module amd64_edac controller F10h: DEV 0000:00:19.2 (INTERRUPT)
[    7.866711] sata_nv 0000:00:07.0: version 3.5
[    7.866736] EDAC PCI0: Giving out device to module amd64_edac controller EDAC PCI controller: DEV 0000:00:18.2 (POLLED)
[    7.866817] kvm: Nested Virtualization enabled
[    7.866822] kvm: Nested Paging enabled
[    7.867110] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
[    7.868070] scsi2 : sata_nv
[    7.869176] scsi3 : sata_nv
[    7.869301] ata3: SATA max UDMA/133 cmd 0x3050 ctl 0x3070 bmdma 0x3030 irq 21
[    7.869304] ata4: SATA max UDMA/133 cmd 0x3058 ctl 0x3074 bmdma 0x3038 irq 21
[    7.873290] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 20
[    7.873984] scsi4 : sata_nv
[    7.874172] scsi5 : sata_nv
[    7.874238] ata5: SATA max UDMA/133 cmd 0x3060 ctl 0x3078 bmdma 0x3040 irq 20
[    7.874240] ata6: SATA max UDMA/133 cmd 0x3068 ctl 0x307c bmdma 0x3048 irq 20
[    8.179363] ata3: SATA link down (SStatus 0 SControl 300)
[    8.183365] ata5: SATA link down (SStatus 0 SControl 300)
[    8.499260] ata4: SATA link down (SStatus 0 SControl 300)
[    8.815157] ata6: SATA link down (SStatus 0 SControl 300)
[   38.704999] *****RAPTOR ENGINEERING AUTOMATED TEST BOOT SUCCESS*****