[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt9-2 (2015-04-13)
[    0.000000] Command line: root=/dev/nfs initrd=initrd-cb-test-tgt-i386 rootfstype=nfs nfsroot=10.100.1.100:/nfsroots/cb-test-tgt-01,v3,hard,nointr,tcp ip=10.100.1.10::10.100.1.1:255.255.255.0:embed-o-matic:eth0:off console=ttyS0,115200n8 consoleblank=0 rw BOOT_IMAGE=vmlinuz-cb-test-tgt-i386 
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bff99fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bff9a000-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: ASUS KFSN4-DRE/KFSN4-DRE, BIOS RAPTOR-NORMAL 03/24/2017
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] AGP: No AGP bridge found
[    0.000000] e820: last_pfn = 0x180000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-back
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000F8000000 mask FFFFFC000000 write-combining
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000180000000 aka 6144M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0xbff9a max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f0690-0x000f069f] mapped at [ffff8800000f0690]
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01af4000, 0x01af4fff] PGTABLE
[    0.000000] BRK [0x01af5000, 0x01af5fff] PGTABLE
[    0.000000] BRK [0x01af6000, 0x01af6fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x17fe00000-0x17fffffff]
[    0.000000]  [mem 0x17fe00000-0x17fffffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x17c000000-0x17fdfffff]
[    0.000000]  [mem 0x17c000000-0x17fdfffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x100000000-0x17bffffff]
[    0.000000]  [mem 0x100000000-0x17bffffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x00100000-0xbff99fff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x3fffffff] page 2M
[    0.000000]  [mem 0x40000000-0x7fffffff] page 1G
[    0.000000]  [mem 0x80000000-0xbfdfffff] page 2M
[    0.000000]  [mem 0xbfe00000-0xbff99fff] page 4k
[    0.000000] RAMDISK: [mem 0x7f24c000-0x7fffefff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F07F0 000024 (v02 CORE  )
[    0.000000] ACPI: XSDT 0x00000000BFFAB0E0 00006C (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: FACP 0x00000000BFFAD910 000074 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: DSDT 0x00000000BFFAB280 002687 (v02 ASUS   COREBOOT 00000001 INTL 20160831)
[    0.000000] ACPI: FACS 0x00000000BFFAB240 000040
[    0.000000] ACPI: SSDT 0x00000000BFFADA10 000E1E (v02 CORE   COREBOOT 0000002A CORE 0000002A)
[    0.000000] ACPI: TCPA 0x00000000BFFAE830 000032 (v02 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: APIC 0x00000000BFFAE870 000072 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SRAT 0x00000000BFFAE8F0 0000F0 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SLIT 0x00000000BFFAE9E0 000030 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: HPET 0x00000000BFFAEA10 000038 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SRAT 0x00000000BFFAEA50 0000F0 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SLIT 0x00000000BFFAEB40 000030 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] SRAT: PXM 0 -> APIC 0x00 -> Node 0
[    0.000000] SRAT: PXM 1 -> APIC 0x04 -> Node 1
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x00000000-0x0009ffff]
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x00100000-0xbfffffff]
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x100000000-0x13fffffff]
[    0.000000] SRAT: Node 1 PXM 1 [mem 0x140000000-0x17fffffff]
[    0.000000] NUMA: Initialized distance table, cnt=2
[    0.000000] NUMA: Node 0 [mem 0x00000000-0x0009ffff] + [mem 0x00100000-0xbfffffff] -> [mem 0x00000000-0xbfffffff]
[    0.000000] NUMA: Node 0 [mem 0x00000000-0xbfffffff] + [mem 0x100000000-0x13fffffff] -> [mem 0x00000000-0x13fffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x13fffffff]
[    0.000000]   NODE_DATA [mem 0x13fffb000-0x13fffffff]
[    0.000000] Initmem setup node 1 [mem 0x140000000-0x17fffffff]
[    0.000000]   NODE_DATA [mem 0x17fff8000-0x17fffcfff]
[    0.000000]  [ffffea0000000000-ffffea00045fffff] PMD -> [ffff88013be00000-ffff88013f5fffff] on node 0
[    0.000000]  [ffffea0004600000-ffffea00053fffff] PMD -> [ffff88017e600000-ffff88017f3fffff] on node 1
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x17fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0xbff99fff]
[    0.000000]   node   0: [mem 0x100000000-0x13fffffff]
[    0.000000]   node   1: [mem 0x140000000-0x17fffffff]
[    0.000000] On node 0 totalpages: 1048376
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10695 pages used for memmap
[    0.000000]   DMA32 zone: 782234 pages, LIFO batch:31
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 262144 pages, LIFO batch:31
[    0.000000] On node 1 totalpages: 262144
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 262144 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x2008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x18] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 24, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xbff9a000-0xcfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xffffffff]
[    0.000000] e820: [mem 0xd0000000-0xffffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:2
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88013fc00000 s80896 r8192 d21504 u2097152
[    0.000000] pcpu-alloc: s80896 r8192 d21504 u2097152 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 [1] 1 
[    0.000000] Built 2 zonelists in Node order, mobility grouping on.  Total pages: 1292580
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=/dev/nfs initrd=initrd-cb-test-tgt-i386 rootfstype=nfs nfsroot=10.100.1.100:/nfsroots/cb-test-tgt-01,v3,hard,nointr,tcp ip=10.100.1.10::10.100.1.1:255.255.255.0:embed-o-matic:eth0:off console=ttyS0,115200n8 consoleblank=0 rw BOOT_IMAGE=vmlinuz-cb-test-tgt-i386 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] AGP: Node 0: aperture [bus addr 0xe5fa000000-0xe5fbffffff] (32MB)
[    0.000000] Aperture beyond 4GB. Ignoring.
[    0.000000] AGP: Your BIOS doesn't leave a aperture memory hole
[    0.000000] AGP: Please enable the IOMMU option in the BIOS setup
[    0.000000] AGP: This costs you 64MB of RAM
[    0.000000] AGP: Mapping aperture over RAM [mem 0xb4000000-0xb7ffffff] (65536KB)
[    0.000000] PM: Registered nosave memory: [mem 0xb4000000-0xb7ffffff]
[    0.000000] Memory: 5012856K/5242080K available (5207K kernel code, 946K rwdata, 1832K rodata, 1204K init, 840K bss, 229224K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:33024 nr_irqs:512 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour *CGA 80x25
[    0.000000] console [ttyS0] enabled
[    0.000000] mempolicy: Disabling automatic NUMA balancing. Configure with numa_balancing= or the kernel.numa_balancing sysctl
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1909.731 MHz processor
[    0.000148] Calibrating delay loop (skipped), value calculated using timer frequency.. 3819.46 BogoMIPS (lpj=7638924)
[    0.010769] pid_max: default: 32768 minimum: 301
[    0.015405] ACPI: Core revision 20140424
[    0.021629] ACPI: All ACPI Tables successfully acquired
[    0.026950] Security Framework initialized
[    0.031062] AppArmor: AppArmor disabled by boot time parameter
[    0.036890] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.044326] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.057220] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.066920] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.073810] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.081614] Initializing cgroup subsys memory
[    0.085979] Initializing cgroup subsys devices
[    0.090434] Initializing cgroup subsys freezer
[    0.094879] Initializing cgroup subsys net_cls
[    0.099326] Initializing cgroup subsys blkio
[    0.103605] Initializing cgroup subsys perf_event
[    0.108315] Initializing cgroup subsys net_prio
[    0.112884] tseg: 0000000000
[    0.112895] CPU: Physical Processor ID: 0
[    0.116908] CPU: Processor Core ID: 0
[    0.120572] mce: CPU supports 6 MCE banks
[    0.124590] LVT offset 0 assigned for vector 0xf9
[    0.129303] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8
Last level dTLB entries: 4KB 512, 2MB 128, 4MB 64, 1GB 0
tlb_flushall_shift: 6
[    0.144634] Freeing SMP alternatives memory: 20K (ffffffff81a1b000 - ffffffff81a20000)
[    0.153630] ftrace: allocating 21614 entries in 85 pages
[    0.168780] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=0 pin2=0
[    0.214289] smpboot: CPU0: Quad-Core AMD Opteron(tm) Processor 8347 (fam: 10, model: 02, stepping: 01)
[    0.328536] Performance Events: AMD PMU driver.
[    0.333094] ... version:                0
[    0.337100] ... bit width:              48
[    0.341198] ... generic registers:      4
[    0.345208] ... value mask:             0000ffffffffffff
[    0.350511] ... max period:             00007fffffffffff
[    0.355811] ... fixed-purpose events:   0
[    0.359815] ... event mask:             000000000000000f
[    0.367315] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.375570] x86: Booting SMP configuration:
[    0.379751] .... node  #1, CPUs:      #1
[    0.492556] x86: Booted up 2 nodes, 2 CPUs
[    0.496841] smpboot: Total of 2 processors activated (7639.05 BogoMIPS)
[    0.505274] devtmpfs: initialized
[    0.516399] pinctrl core: initialized pinctrl subsystem
[    0.521770] NET: Registered protocol family 16
[    0.526429] cpuidle: using governor ladder
[    0.530528] cpuidle: using governor menu
[    0.534457] node 0 link 1: io port [1000, 3fff]
[    0.534460] TOM: 00000000c0000000 aka 3072M
[    0.538644] Fam 10h mmconf [mem 0xc0000000-0xcfffffff]
[    0.538648] node 0 link 1: mmio [fc000000, fc3fffff]
[    0.538651] node 0 link 1: mmio [f8000000, fbffffff]
[    0.538653] TOM2: 0000000180000000 aka 6144M
[    0.542925] bus: [bus 00-05] on node 0 link 1
[    0.542927] bus: 00 [io  0x0000-0xffff]
[    0.542929] bus: 00 [mem 0xd0000000-0xffffffff]
[    0.542930] bus: 00 [mem 0x180000000-0xfcffffffff]
[    0.543013] ACPI: bus type PCI registered
[    0.547025] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.553601] PCI: Using configuration type 1 for base access
[    0.559167] PCI: Using configuration type 1 for extended access
[    0.577219] ACPI: Added _OSI(Module Device)
[    0.581404] ACPI: Added _OSI(Processor Device)
[    0.585843] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.590548] ACPI: Added _OSI(Processor Aggregator Device)
[    0.596926] ACPI: Executed 1 blocks of module-level executable AML code
[    0.605918] ACPI: Interpreter enabled
[    0.609594] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[    0.618843] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20140424/hwxface-580)
[    0.628095] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S4_] (20140424/hwxface-580)
[    0.637335] ACPI: (supports S0 S1 S5)
[    0.640995] ACPI: Using IOAPIC for interrupt routing
[    0.645994] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.670941] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-05])
[    0.677122] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.685326] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.716956] acpi PNP0A03:00: host bridge window expanded to [io  0x0000-0x0cf7]; [io  0x03b0-0x03df] ignored
[    0.726953] PCI host bridge to bus 0000:00
[    0.731050] pci_bus 0000:00: root bus resource [bus 00-05]
[    0.736530] pci_bus 0000:00: root bus resource [io  0x0d00-0x3fff]
[    0.742708] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.749579] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfbffffff]
[    0.756448] pci_bus 0000:00: root bus resource [mem 0xfc000000-0xfc3fffff]
[    0.763319] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.769508] pci 0000:00:00.0: [10de:005e] type 00 class 0x058000
[    0.769668] pci 0000:00:01.0: [10de:0051] type 00 class 0x060100
[    0.769675] pci 0000:00:01.0: reg 0x10: [io  0x2c00-0x2c7f]
[    0.769794] pci 0000:00:01.1: [10de:0052] type 00 class 0x0c0500
[    0.769804] pci 0000:00:01.1: reg 0x10: [io  0x3000-0x301f]
[    0.769816] pci 0000:00:01.1: reg 0x20: [io  0x2c80-0x2cbf]
[    0.769822] pci 0000:00:01.1: reg 0x24: [io  0x2cc0-0x2cff]
[    0.769840] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.769943] pci 0000:00:02.0: [10de:005a] type 00 class 0x0c0310
[    0.769953] pci 0000:00:02.0: reg 0x10: [mem 0xfc300000-0xfc300fff]
[    0.769981] pci 0000:00:02.0: supports D1 D2
[    0.769983] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.770028] pci 0000:00:02.0: System wakeup disabled by ACPI
[    0.775743] pci 0000:00:02.1: [10de:005b] type 00 class 0x0c0320
[    0.775753] pci 0000:00:02.1: reg 0x10: [mem 0xfc303000-0xfc3030ff]
[    0.775787] pci 0000:00:02.1: supports D1 D2
[    0.775790] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.775835] pci 0000:00:02.1: System wakeup disabled by ACPI
[    0.781551] pci 0000:00:06.0: [10de:0053] type 00 class 0x01018a
[    0.781568] pci 0000:00:06.0: reg 0x20: [io  0x3020-0x302f]
[    0.781579] pci 0000:00:06.0: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.788703] pci 0000:00:06.0: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.795227] pci 0000:00:06.0: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.802356] pci 0000:00:06.0: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.808967] pci 0000:00:07.0: [10de:0054] type 00 class 0x010185
[    0.808978] pci 0000:00:07.0: reg 0x10: [io  0x3050-0x3057]
[    0.808983] pci 0000:00:07.0: reg 0x14: [io  0x3070-0x3073]
[    0.808988] pci 0000:00:07.0: reg 0x18: [io  0x3058-0x305f]
[    0.808993] pci 0000:00:07.0: reg 0x1c: [io  0x3074-0x3077]
[    0.808997] pci 0000:00:07.0: reg 0x20: [io  0x3030-0x303f]
[    0.809002] pci 0000:00:07.0: reg 0x24: [mem 0xfc301000-0xfc301fff]
[    0.809096] pci 0000:00:08.0: [10de:0055] type 00 class 0x010185
[    0.809107] pci 0000:00:08.0: reg 0x10: [io  0x3060-0x3067]
[    0.809112] pci 0000:00:08.0: reg 0x14: [io  0x3078-0x307b]
[    0.809116] pci 0000:00:08.0: reg 0x18: [io  0x3068-0x306f]
[    0.809121] pci 0000:00:08.0: reg 0x1c: [io  0x307c-0x307f]
[    0.809126] pci 0000:00:08.0: reg 0x20: [io  0x3040-0x304f]
[    0.809131] pci 0000:00:08.0: reg 0x24: [mem 0xfc302000-0xfc302fff]
[    0.809227] pci 0000:00:09.0: [10de:005c] type 01 class 0x060400
[    0.809289] pci 0000:00:09.0: System wakeup disabled by ACPI
[    0.815006] pci 0000:00:0b.0: [10de:005d] type 01 class 0x060400
[    0.815048] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.815093] pci 0000:00:0b.0: System wakeup disabled by ACPI
[    0.820817] pci 0000:00:0c.0: [10de:005d] type 01 class 0x060400
[    0.820852] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.820898] pci 0000:00:0c.0: System wakeup disabled by ACPI
[    0.826616] pci 0000:00:0d.0: [10de:005d] type 01 class 0x060400
[    0.826653] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.826704] pci 0000:00:0d.0: System wakeup disabled by ACPI
[    0.832419] pci 0000:00:0e.0: [10de:005d] type 01 class 0x060400
[    0.832452] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.832499] pci 0000:00:0e.0: System wakeup disabled by ACPI
[    0.838222] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000
[    0.838328] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000
[    0.838425] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000
[    0.838517] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000
[    0.838614] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000
[    0.838712] pci 0000:00:19.0: [1022:1200] type 00 class 0x060000
[    0.838816] pci 0000:00:19.1: [1022:1201] type 00 class 0x060000
[    0.838909] pci 0000:00:19.2: [1022:1202] type 00 class 0x060000
[    0.839003] pci 0000:00:19.3: [1022:1203] type 00 class 0x060000
[    0.839105] pci 0000:00:19.4: [1022:1204] type 00 class 0x060000
[    0.839258] pci 0000:01:04.0: [18ca:0020] type 00 class 0x030000
[    0.839271] pci 0000:01:04.0: reg 0x10: [mem 0xf8000000-0xfbffffff pref]
[    0.839281] pci 0000:01:04.0: reg 0x14: [mem 0xfc000000-0xfc03ffff]
[    0.839288] pci 0000:01:04.0: reg 0x18: [io  0x1000-0x107f]
[    0.839328] pci 0000:01:04.0: supports D1 D2
[    0.839397] pci 0000:00:09.0: PCI bridge to [bus 01]
[    0.844361] pci 0000:00:09.0:   bridge window [io  0x1000-0x1fff]
[    0.844365] pci 0000:00:09.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    0.844368] pci 0000:00:09.0:   bridge window [mem 0xf8000000-0xfbffffff pref]
[    0.844448] pci 0000:02:00.0: [14e4:1659] type 00 class 0x020000
[    0.844466] pci 0000:02:00.0: reg 0x10: [mem 0xfc100000-0xfc10ffff 64bit]
[    0.844494] pci 0000:02:00.0: reg 0x30: [mem 0x68400000-0x6840ffff pref]
[    0.844557] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.844635] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.854632] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    0.859591] pci 0000:00:0b.0:   bridge window [mem 0xfc100000-0xfc1fffff]
[    0.859668] pci 0000:03:00.0: [14e4:1659] type 00 class 0x020000
[    0.859686] pci 0000:03:00.0: reg 0x10: [mem 0xfc200000-0xfc20ffff 64bit]
[    0.859772] pci 0000:03:00.0: PME# supported from D3hot D3cold
[    0.859848] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.869844] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    0.874805] pci 0000:00:0c.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    0.874866] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    0.879884] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    0.884861] pci_bus 0000:00: on NUMA node 0
[    0.884961] ACPI: PCI Interrupt Link [LNKA] (IRQs *16 17 18 19)
[    0.891060] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 *17 18 19)
[    0.897185] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[    0.904456] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[    0.911721] ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled.
[    0.919000] ACPI: PCI Interrupt Link [LLAS] (IRQs 20 21 22 23) *0, disabled.
[    0.926263] ACPI: PCI Interrupt Link [LUOH] (IRQs 20 21 22 *23)
[    0.932359] ACPI: PCI Interrupt Link [LUEH] (IRQs 20 21 *22 23)
[    0.938468] ACPI: PCI Interrupt Link [LAUD] (IRQs 20 21 22 23) *0, disabled.
[    0.945740] ACPI: PCI Interrupt Link [LMOD] (IRQs 20 21 22 23) *0, disabled.
[    0.953019] ACPI: PCI Interrupt Link [LPA0] (IRQs 20 21 22 23) *0, disabled.
[    0.960286] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 *21 22 23)
[    0.966383] ACPI: PCI Interrupt Link [LSA1] (IRQs *20 21 22 23)
[    0.972495] ACPI: PCI Interrupt Link [LEMA] (IRQs 20 21 22 23) *0, disabled.
[    0.979763] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *0, disabled.
[    0.987044] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *0, disabled.
[    0.994314] ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    1.002813] ACPI: PCI Interrupt Link [LNIA] (IRQs 16) *0, disabled.
[    1.009243] ACPI: PCI Interrupt Link [LNIB] (IRQs 17) *0, disabled.
[    1.015677] ACPI: PCI Interrupt Link [LNIC] (IRQs 18) *0, disabled.
[    1.022122] ACPI: PCI Interrupt Link [LNND] (IRQs 19) *0, disabled.
[    1.028848] ACPI: Enabled 1 GPEs in block 00 to 1F
[    1.033918] vgaarb: setting as boot device: PCI:0000:01:04.0
[    1.039577] vgaarb: device added: PCI:0000:01:04.0,decodes=io+mem,owns=io+mem,locks=none
[    1.047663] vgaarb: loaded
[    1.050371] vgaarb: bridge control possible 0000:01:04.0
[    1.055833] PCI: Using ACPI for IRQ routing
[    1.060019] PCI: pci_cache_line_size set to 64 bytes
[    1.060075] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    1.060079] e820: reserve RAM buffer [mem 0xbff9a000-0xbfffffff]
[    1.060380] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    1.067425] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    1.072464] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    1.080499] Switched to clocksource hpet
[    1.096035] pnp: PnP ACPI init
[    1.099138] ACPI: bus type PNP registered
[    1.103647] pnp 00:00: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    1.103734] pnp 00:01: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[    1.103815] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.103887] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.103924] pnp 00:04: [dma 2]
[    1.103958] pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
[    1.103989] pnp: PnP ACPI: found 5 devices
[    1.108084] ACPI: bus type PNP unregistered
[    1.119247] pci 0000:02:00.0: can't claim BAR 6 [mem 0x68400000-0x6840ffff pref]: no compatible bridge window
[    1.129195] pci 0000:00:09.0: PCI bridge to [bus 01]
[    1.134162] pci 0000:00:09.0:   bridge window [io  0x1000-0x1fff]
[    1.140254] pci 0000:00:09.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    1.147035] pci 0000:00:09.0:   bridge window [mem 0xf8000000-0xfbffffff pref]
[    1.154259] pci 0000:02:00.0: BAR 6: assigned [mem 0xfc110000-0xfc11ffff pref]
[    1.161478] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    1.166440] pci 0000:00:0b.0:   bridge window [mem 0xfc100000-0xfc1fffff]
[    1.173229] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    1.178190] pci 0000:00:0c.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    1.184976] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    1.189942] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    1.194906] pci_bus 0000:00: resource 4 [io  0x0d00-0x3fff]
[    1.194909] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[    1.194911] pci_bus 0000:00: resource 6 [mem 0xf8000000-0xfbffffff]
[    1.194914] pci_bus 0000:00: resource 7 [mem 0xfc000000-0xfc3fffff]
[    1.194916] pci_bus 0000:00: resource 8 [io  0x0000-0x0cf7]
[    1.194919] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]
[    1.194922] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfc0fffff]
[    1.194924] pci_bus 0000:01: resource 2 [mem 0xf8000000-0xfbffffff pref]
[    1.194927] pci_bus 0000:02: resource 1 [mem 0xfc100000-0xfc1fffff]
[    1.194930] pci_bus 0000:03: resource 1 [mem 0xfc200000-0xfc2fffff]
[    1.195008] NET: Registered protocol family 2
[    1.199746] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    1.207390] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    1.214730] TCP: Hash tables configured (established 65536 bind 65536)
[    1.221333] TCP: reno registered
[    1.224581] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    1.230791] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    1.237523] NET: Registered protocol family 1
[    1.242262] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[    1.248332] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[    1.254225] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.259745] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.265236] pci 0000:00:0b.0: Found disabled HT MSI Mapping
[    1.270810] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.276334] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.281819] pci 0000:00:0c.0: Found disabled HT MSI Mapping
[    1.287392] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.292921] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.298410] pci 0000:00:0d.0: Found disabled HT MSI Mapping
[    1.303982] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.309515] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.314999] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[    1.320572] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.326081] pci 0000:01:04.0: Video device with shadowed ROM
[    1.326090] PCI: CLS 64 bytes, default 64
[    1.326190] Unpacking initramfs...
[    1.704110] Freeing initrd memory: 14028K (ffff88007f24c000 - ffff88007ffff000)
[    1.711975] PCI-DMA: Disabling AGP.
[    1.715626] PCI-DMA: aperture base @ b4000000 size 65536 KB
[    1.721201] PCI-DMA: using GART IOMMU.
[    1.724961] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    1.736800] platform rtc_cmos: registered platform RTC device (no PNP device found)
[    1.744618] microcode: CPU0: patch_level=0x01000084
[    1.749509] microcode: CPU1: patch_level=0x01000084
[    1.754511] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.763308] LVT offset 1 assigned for vector 0x400
[    1.768110] IBS: LVT offset 1 assigned
[    1.771879] perf: AMD IBS detected (0x00000007)
[    1.776869] futex hash table entries: 512 (order: 3, 32768 bytes)
[    1.783019] audit: initializing netlink subsys (disabled)
[    1.788447] audit: type=2000 audit(1490364582.540:1): initialized
[    1.795288] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.801687] zbud: loaded
[    1.804475] VFS: Disk quotas dquot_6.5.2
[    1.808430] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.814959] msgmni has been set to 9946
[    1.819310] alg: No test for stdrng (krng)
[    1.823465] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.830932] io scheduler noop registered
[    1.834864] io scheduler deadline registered
[    1.839193] io scheduler cfq registered (default)
[    1.844096] pcieport 0000:00:0b.0: irq 40 for MSI/MSI-X
[    1.844220] pcieport 0000:00:0c.0: irq 41 for MSI/MSI-X
[    1.844344] pcieport 0000:00:0d.0: irq 42 for MSI/MSI-X
[    1.844451] pcieport 0000:00:0e.0: irq 43 for MSI/MSI-X
[    1.844605] aer 0000:00:0b.0:pcie02: service driver aer loaded
[    1.844632] aer 0000:00:0c.0:pcie02: service driver aer loaded
[    1.844657] aer 0000:00:0d.0:pcie02: service driver aer loaded
[    1.844679] aer 0000:00:0e.0:pcie02: service driver aer loaded
[    1.844702] pcieport 0000:00:0b.0: Signaling PME through PCIe PME interrupt
[    1.851668] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[    1.858196] pcie_pme 0000:00:0b.0:pcie01: service driver pcie_pme loaded
[    1.858208] pcieport 0000:00:0c.0: Signaling PME through PCIe PME interrupt
[    1.865171] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[    1.871692] pcie_pme 0000:00:0c.0:pcie01: service driver pcie_pme loaded
[    1.871706] pcieport 0000:00:0d.0: Signaling PME through PCIe PME interrupt
[    1.878666] pcie_pme 0000:00:0d.0:pcie01: service driver pcie_pme loaded
[    1.878676] pcieport 0000:00:0e.0: Signaling PME through PCIe PME interrupt
[    1.885632] pcie_pme 0000:00:0e.0:pcie01: service driver pcie_pme loaded
[    1.885663] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.891264] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.897968] GHES: HEST is not enabled!
[    1.901857] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.928429] 00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.956069] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[    1.963932] Linux agpgart interface v0.103
[    1.968183] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f03:MOU] at 0x60,0x64 irq 1,12
[    1.978333] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.983301] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.988543] mousedev: PS/2 mouse device common for all mice
[    1.994221] rtc_cmos rtc_cmos: RTC can wake from S4
[    1.999275] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[    2.005664] rtc_cmos rtc_cmos: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    2.013527] ledtrig-cpu: registered to indicate activity on CPUs
[    2.019711] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[    2.026150] AMD IOMMUv2 functionality not available on this system
[    2.032474] TCP: cubic registered
[    2.035860] NET: Registered protocol family 10
[    2.040687] mip6: Mobile IPv6
[    2.043653] NET: Registered protocol family 17
[    2.048181] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    2.056814] mpls_gso: MPLS GSO support
[    2.061067] registered taskstats version 1
[    2.065855] rtc_cmos rtc_cmos: setting system clock to 2017-03-24 14:09:44 UTC (1490364584)
[    2.074261] PM: Hibernation image not present or could not be loaded.
[    2.076187] Freeing unused kernel memory: 1204K (ffffffff818ee000 - ffffffff81a1b000)
[    2.084012] Write protecting the kernel read-only data: 8192k
[    2.093204] Freeing unused kernel memory: 924K (ffff880001519000 - ffff880001600000)
[    2.101763] Freeing unused kernel memory: 216K (ffff8800017ca000 - ffff880001800000)
[    2.133879] systemd-udevd[63]: starting version 215
[    2.139569] random: systemd-udevd urandom read with 3 bits of entropy available
[    2.179627] SCSI subsystem initialized
[    2.185987] ACPI: bus type USB registered
[    2.190989] usbcore: registered new interface driver usbfs
[    2.191005] libata version 3.00 loaded.
[    2.198148] sata_nv 0000:00:07.0: version 3.5
[    2.198264] FDC 0 is a post-1991 82077
[    2.198407] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
[    2.198889] scsi0 : sata_nv
[    2.210584] usbcore: registered new interface driver hub
[    2.216240] usbcore: registered new device driver usb
[    2.222470] pps_core: LinuxPPS API ver. 1 registered
[    2.222625] scsi1 : sata_nv
[    2.222699] ata1: SATA max UDMA/133 cmd 0x3050 ctl 0x3070 bmdma 0x3030 irq 21
[    2.222701] ata2: SATA max UDMA/133 cmd 0x3058 ctl 0x3074 bmdma 0x3038 irq 21
[    2.222894] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 20
[    2.250210] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.260202] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.266959] scsi2 : sata_nv
[    2.271025] ehci-pci: EHCI PCI platform driver
[    2.275543] scsi3 : sata_nv
[    2.278473] ata3: SATA max UDMA/133 cmd 0x3060 ctl 0x3078 bmdma 0x3040 irq 20
[    2.284759] PTP clock support registered
[    2.289560] ata4: SATA max UDMA/133 cmd 0x3068 ctl 0x307c bmdma 0x3048 irq 20
[    2.298870] ehci-pci 0000:00:02.1: EHCI Host Controller
[    2.303056] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.310735] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 1
[    2.318582] ehci-pci 0000:00:02.1: debug port 1
[    2.323227] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[    2.323257] ehci-pci 0000:00:02.1: irq 22, io mem 0xfc303000
[    2.340082] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    2.346848] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.353643] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.360898] usb usb1: Product: EHCI Host Controller
[    2.365815] usb usb1: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    2.371920] usb usb1: SerialNumber: 0000:00:02.1
[    2.376598] tg3.c:v3.137 (May 11, 2014)
[    2.380448] tg3 0000:02:00.0: enabling device (0004 -> 0006)
[    2.380459] hub 1-0:1.0: USB hub found
[    2.380471] hub 1-0:1.0: 10 ports detected
[    2.394770] ohci-pci: OHCI PCI platform driver
[    2.399762] ACPI: PCI Interrupt Link [LNIB] enabled at IRQ 17
[    2.405687] pata_amd 0000:00:06.0: version 0.4.1
[    2.406260] scsi4 : pata_amd
[    2.409304] scsi5 : pata_amd
[    2.412265] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x3020 irq 14
[    2.419225] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x3028 irq 15
[    2.426478] ohci-pci 0000:00:02.0: OHCI PCI host controller
[    2.432679] ohci-pci 0000:00:02.0: new USB bus registered, assigned bus number 2
[    2.440296] ohci-pci 0000:00:02.0: irq 23, io mem 0xfc300000
[    2.451867] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM95721) rev 4201] (PCI Express) MAC address 00:1e:8c:51:61:a2
[    2.462125] tg3 0000:02:00.0 eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    2.471863] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.479689] tg3 0000:02:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.486490] tg3 0000:03:00.0: enabling device (0004 -> 0006)
[    2.492288] ACPI: PCI Interrupt Link [LNIA] enabled at IRQ 16
[    2.502099] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.508891] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.516113] usb usb2: Product: OHCI PCI host controller
[    2.521337] usb usb2: Manufacturer: Linux 3.16.0-4-amd64 ohci_hcd
[    2.527426] usb usb2: SerialNumber: 0000:00:02.0
[    2.532371] hub 2-0:1.0: USB hub found
[    2.536131] hub 2-0:1.0: 10 ports detected
[    2.543408] tg3 0000:03:00.0 eth1: Tigon3 [partno(BCM95721) rev 4201] (PCI Express) MAC address 00:1e:8c:51:63:95
[    2.553671] tg3 0000:03:00.0 eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    2.563400] tg3 0000:03:00.0 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.571221] tg3 0000:03:00.0 eth1: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.577994] ata1: SATA link down (SStatus 0 SControl 300)
[    2.611987] ata3: SATA link down (SStatus 0 SControl 300)
[    2.735940] tsc: Refined TSC clocksource calibration: 1909.786 MHz
[    2.891882] ata2: SATA link down (SStatus 0 SControl 300)
[    3.207773] ata4: SATA link down (SStatus 0 SControl 300)
[    3.393724] FS-Cache: Loaded
[    3.401226] RPC: Registered named UNIX socket transport module.
[    3.408254] RPC: Registered udp transport module.
[    3.414344] RPC: Registered tcp transport module.
[    3.420421] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    3.433578] FS-Cache: Netfs 'nfs' registered for caching
[    3.446841] tg3 0000:02:00.0: irq 44 for MSI/MSI-X
[    3.491782] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    3.739687] Switched to clocksource tsc
[    6.242197] tg3 0000:02:00.0 eth0: Link is up at 1000 Mbps, full duplex
[    6.248805] tg3 0000:02:00.0 eth0: Flow control is on for TX and on for RX
[    6.255679] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    6.675879] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    6.689701] systemd[1]: Detected architecture 'x86-64'.
[    6.735786] systemd[1]: Inserted module 'autofs4'
[    6.742572] systemd[1]: Set hostname to <cb-test-tgt>.
[    6.902169] systemd[1]: Cannot add dependency job for unit dbus.socket, ignoring: Unit dbus.socket failed to load: No such file or directory.
[    6.914889] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    6.930239] systemd[1]: Expecting device dev-ttyS0.device...
[    6.946653] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    6.954450] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    6.962056] systemd[1]: Starting Remote File Systems (Pre).
[    6.978507] systemd[1]: Reached target Remote File Systems (Pre).
[    6.984641] systemd[1]: Starting Encrypted Volumes.
[    6.998494] systemd[1]: Reached target Encrypted Volumes.
[    7.003943] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    7.026485] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    7.035905] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[    7.043951] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    7.051885] systemd[1]: Starting Paths.
[    7.066473] systemd[1]: Reached target Paths.
[    7.070857] systemd[1]: Starting Swap.
[    7.082465] systemd[1]: Reached target Swap.
[    7.086750] systemd[1]: Starting Root Slice.
[    7.098459] systemd[1]: Created slice Root Slice.
[    7.103189] systemd[1]: Starting User and Session Slice.
[    7.118453] systemd[1]: Created slice User and Session Slice.
[    7.124217] systemd[1]: Starting Delayed Shutdown Socket.
[    7.138443] systemd[1]: Listening on Delayed Shutdown Socket.
[    7.144201] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[    7.162445] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    7.169421] systemd[1]: Starting Journal Socket (/dev/log).
[    7.186427] systemd[1]: Listening on Journal Socket (/dev/log).
[    7.192369] systemd[1]: Starting udev Kernel Socket.
[    7.206420] systemd[1]: Listening on udev Kernel Socket.
[    7.211759] systemd[1]: Starting udev Control Socket.
[    7.226414] systemd[1]: Listening on udev Control Socket.
[    7.231840] systemd[1]: Starting Journal Socket.
[    7.246403] systemd[1]: Listening on Journal Socket.
[    7.251404] systemd[1]: Starting System Slice.
[    7.266403] systemd[1]: Created slice System Slice.
[    7.271298] systemd[1]: Starting system-getty.slice.
[    7.286396] systemd[1]: Created slice system-getty.slice.
[    7.291810] systemd[1]: Starting system-serial\x2dgetty.slice.
[    7.306385] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    7.312688] systemd[1]: Starting Increase datagram queue length...
[    7.331893] systemd[1]: Starting udev Coldplug all Devices...
[    7.359792] systemd[1]: Starting Load Kernel Modules...
[    7.378453] systemd[1]: Started Set Up Additional Binary Formats.
[    7.385372] systemd[1]: Mounting Debug File System...
[    7.400132] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    7.424060] systemd[1]: Mounting POSIX Message Queue File System...
[    7.443639] systemd[1]: Mounting Huge Pages File System...
[    7.459605] systemd[1]: Starting Slices.
[    7.474410] systemd[1]: Reached target Slices.
[    7.478952] systemd[1]: Starting Remount Root and Kernel File Systems...
[    7.506422] systemd[1]: Mounted Huge Pages File System.
[    7.522422] systemd[1]: Mounted POSIX Message Queue File System.
[    7.538313] systemd[1]: Mounted Debug File System.
[    7.554336] systemd[1]: Started Increase datagram queue length.
[    7.570395] systemd[1]: Started Load Kernel Modules.
[    7.590396] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    7.614301] systemd[1]: Started Remount Root and Kernel File Systems.
[    7.630294] systemd[1]: Started udev Coldplug all Devices.
[    7.676606] systemd[1]: Started Various fixups to make systemd work better on Debian.
[    7.684466] systemd[1]: Starting Load/Save Random Seed...
[    7.700012] systemd[1]: Starting Create Static Device Nodes in /dev...
[    7.719785] systemd[1]: Starting Apply Kernel Variables...
[    7.735958] systemd[1]: Mounted Configuration File System.
[    7.741839] systemd[1]: Mounted FUSE Control File System.
[    7.747465] systemd[1]: Starting Syslog Socket.
[    7.762337] systemd[1]: Listening on Syslog Socket.
[    7.767289] systemd[1]: Starting Sockets.
[    7.778222] systemd[1]: Reached target Sockets.
[    7.782782] systemd[1]: Starting Journal Service...
[    7.810306] systemd[1]: Started Journal Service.
[    7.901027] systemd-udevd[162]: starting version 215
[    7.994373] systemd-journald[161]: Received request to flush runtime journal from PID 1
[    8.082262] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.099479] acpi-cpufreq: overriding BIOS provided _PSD data
[    8.106355] i2c i2c-0: nForce2 SMBus adapter at 0x2c80
[    8.112967] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    8.121483] i2c i2c-1: nForce2 SMBus adapter at 0x2cc0
[    8.134010] ACPI: Power Button [PWRB]
[    8.141570] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    8.156164] ACPI: Power Button [PWRF]
[    8.182801] k10temp 0000:00:18.3: unreliable CPU thermal sensor; monitoring disabled
[    8.196380] EDAC MC: Ver: 3.0.0
[    8.201206] input: PC Speaker as /devices/platform/pcspkr/input/input4
[    8.210935] k10temp 0000:00:19.3: unreliable CPU thermal sensor; monitoring disabled
[    8.220062] MCE: In-kernel MCE decoding enabled.
[    8.235142] AMD64 EDAC driver v3.4.0
[    8.243085] EDAC amd64: DRAM ECC enabled.
[    8.257122] EDAC amd64: F10h detected (node 0).
[    8.261710] EDAC MC: DCT0 chip selects:
[    8.261713] EDAC amd64: MC: 0:     0MB 1:     0MB
[    8.266663] EDAC amd64: MC: 2:     0MB 3:     0MB
[    8.271372] EDAC amd64: MC: 4:     0MB 5:     0MB
[    8.276079] EDAC amd64: MC: 6:  2048MB 7:  2048MB
[    8.280775] EDAC MC: DCT1 chip selects:
[    8.280776] EDAC amd64: MC: 0:     0MB 1:     0MB
[    8.285479] EDAC amd64: MC: 2:     0MB 3:     0MB
[    8.290184] EDAC amd64: MC: 4:     0MB 5:     0MB
[    8.294888] EDAC amd64: MC: 6:  1024MB 7:  1024MB
[    8.299593] EDAC amd64: using x4 syndromes.
[    8.311525] EDAC amd64: CS6: Registered DDR2 RAM
[    8.316169] EDAC amd64: CS7: Registered DDR2 RAM
[    8.321779] EDAC MC0: Giving out device to module amd64_edac controller F10h: DEV 0000:00:18.2 (INTERRUPT)
[    8.335561] EDAC amd64: DRAM ECC enabled.
[    8.336943] kvm: Nested Virtualization enabled
[    8.336963] kvm: Nested Paging enabled
[    8.360353] EDAC amd64: F10h detected (node 1).
[    8.364936] EDAC MC: DCT0 chip selects:
[    8.364939] EDAC amd64: MC: 0:  1024MB 1:     0MB
[    8.369659] EDAC amd64: MC: 2:     0MB 3:     0MB
[    8.374367] EDAC amd64: MC: 4:     0MB 5:     0MB
[    8.379073] EDAC amd64: MC: 6:     0MB 7:     0MB
[    8.383785] EDAC MC: DCT1 chip selects:
[    8.383786] EDAC amd64: MC: 0:     0MB 1:     0MB
[    8.388497] EDAC amd64: MC: 2:     0MB 3:     0MB
[    8.393201] EDAC amd64: MC: 4:     0MB 5:     0MB
[    8.397912] EDAC amd64: MC: 6:     0MB 7:     0MB
[    8.402619] EDAC amd64: using x4 syndromes.
[    8.406804] EDAC amd64: MCT channel count: 1
[    8.411128] EDAC amd64: CS0: Registered DDR2 RAM
[    8.415912] EDAC MC1: Giving out device to module amd64_edac controller F10h: DEV 0000:00:19.2 (INTERRUPT)
[    8.425980] EDAC PCI0: Giving out device to module amd64_edac controller EDAC PCI controller: DEV 0000:00:18.2 (POLLED)
[    8.519057] random: nonblocking pool is initialized
[   38.690024] *****RAPTOR ENGINEERING AUTOMATED TEST BOOT SUCCESS*****