blob: 7fb56dc07349cdd0e4186950fa17b5c2e8acf816 [file] [log] [blame]
*** Pre-CBMEM romstage console overflowed, log truncated! ***
reference clock support: yes
[DEBUG] PLL_REF100_CFG value: 0x7
[DEBUG] Trying CAS 11, tCK 320.
[DEBUG] Found compatible clock, CAS pair.
[DEBUG] Selected DRAM frequency: 800 MHz
[DEBUG] Selected CAS latency : 11T
[DEBUG] MPLL busy... done in 40 us
[DEBUG] MPLL frequency is set at : 800 MHz
[DEBUG] Selected CWL latency : 8T
[DEBUG] Selected tRCD : 11T
[DEBUG] Selected tRP : 11T
[DEBUG] Selected tRAS : 28T
[DEBUG] Selected tWR : 12T
[DEBUG] Selected tFAW : 24T
[DEBUG] Selected tRRD : 5T
[DEBUG] Selected tRTP : 6T
[DEBUG] Selected tWTR : 6T
[DEBUG] Selected tRFC : 128T
[DEBUG] Done dimm mapping
[DEBUG] Update PCI-E configuration space:
[DEBUG] PCI(0, 0, 0)[a0] = 0
[DEBUG] PCI(0, 0, 0)[a4] = 1
[DEBUG] PCI(0, 0, 0)[bc] = 82a00000
[DEBUG] PCI(0, 0, 0)[a8] = 7d600000
[DEBUG] PCI(0, 0, 0)[ac] = 1
[DEBUG] PCI(0, 0, 0)[b8] = 80000000
[DEBUG] PCI(0, 0, 0)[b0] = 80a00000
[DEBUG] PCI(0, 0, 0)[b4] = 80800000
[DEBUG] Done memory map
[DEBUG] Done io registers
[DEBUG] Done jedec reset
[DEBUG] Done MRS commands
[WARN ] Logic delay 2 greater than 1: 0 3
[DEBUG] t123: 1767, 6000, 7620
[NOTE ] ME: Wrong mode : 2
[NOTE ] ME: FWS2: 0x100a0140
[NOTE ] ME: Bist in progress: 0x0
[NOTE ] ME: ICC Status : 0x0
[NOTE ] ME: Invoke MEBx : 0x0
[NOTE ] ME: CPU replaced : 0x0
[NOTE ] ME: MBP ready : 0x0
[NOTE ] ME: MFS failure : 0x1
[NOTE ] ME: Warm reset req : 0x0
[NOTE ] ME: CPU repl valid : 0x1
[NOTE ] ME: (Reserved) : 0x0
[NOTE ] ME: FW update req : 0x0
[NOTE ] ME: (Reserved) : 0x0
[NOTE ] ME: Current state : 0xa
[NOTE ] ME: Current PM event: 0x0
[NOTE ] ME: Progress code : 0x1
[NOTE ] PASSED! Tell ME that DRAM is ready
[NOTE ] ME: ME is reporting as disabled, so not waiting for a response.
[NOTE ] ME: FWS2: 0x100a0140
[NOTE ] ME: Bist in progress: 0x0
[NOTE ] ME: ICC Status : 0x0
[NOTE ] ME: Invoke MEBx : 0x0
[NOTE ] ME: CPU replaced : 0x0
[NOTE ] ME: MBP ready : 0x0
[NOTE ] ME: MFS failure : 0x1
[NOTE ] ME: Warm reset req : 0x0
[NOTE ] ME: CPU repl valid : 0x1
[NOTE ] ME: (Reserved) : 0x0
[NOTE ] ME: FW update req : 0x0
[NOTE ] ME: (Reserved) : 0x0
[NOTE ] ME: Current state : 0xa
[NOTE ] ME: Current PM event: 0x0
[NOTE ] ME: Progress code : 0x1
[NOTE ] ME: Requested BIOS Action: No DID Ack received
[DEBUG] ME: FW Partition Table : OK
[DEBUG] ME: Bringup Loader Failure : NO
[DEBUG] ME: Firmware Init Complete : NO
[DEBUG] ME: Manufacturing Mode : YES
[DEBUG] ME: Boot Options Present : NO
[DEBUG] ME: Update In Progress : NO
[DEBUG] ME: Current Working State : Initializing
[DEBUG] ME: Current Operation State : Bring up
[DEBUG] ME: Current Operation Mode : Debug or Disabled by AltDisableBit
[DEBUG] ME: Error Code : No Error
[DEBUG] ME: Progress Phase : BUP Phase
[DEBUG] ME: Power Management Event : Clean Moff->Mx wake
[DEBUG] ME: Progress Phase State : Check to see if straps say ME DISABLED
[DEBUG] memcfg DDR3 ref clock 133 MHz
[DEBUG] memcfg DDR3 clock 1596 MHz
[DEBUG] memcfg channel assignment: A: 0, B 1, C 2
[DEBUG] memcfg channel[0] config (00630010):
[DEBUG] ECC inactive
[DEBUG] enhanced interleave mode on
[DEBUG] rank interleave on
[DEBUG] DIMMA 4096 MB width x8 dual rank
[DEBUG] DIMMB 0 MB width x8 single rank, selected
[DEBUG] memcfg channel[1] config (00000000):
[DEBUG] ECC inactive
[DEBUG] enhanced interleave mode off
[DEBUG] rank interleave off
[DEBUG] DIMMA 0 MB width x8 single rank, selected
[DEBUG] DIMMB 0 MB width x8 single rank
[DEBUG] CBMEM:
[DEBUG] IMD: root @ 0x7ffff000 254 entries.
[DEBUG] IMD: root @ 0x7fffec00 62 entries.
[DEBUG] External stage cache:
[DEBUG] IMD: root @ 0x803ff000 254 entries.
[DEBUG] IMD: root @ 0x803fec00 62 entries.
[DEBUG] FMAP: area RW_MRC_CACHE found @ 800000 (65536 bytes)
[DEBUG] MRC: Checking cached data update for 'RW_MRC_CACHE'.
[DEBUG] flash size 0xc00000 bytes
[INFO ] SF: Detected 00 0000 with sector size 0x100, total 0xc00000
[NOTE ] MRC: no data in 'RW_MRC_CACHE'
[DEBUG] MRC: cache data 'RW_MRC_CACHE' needs update.
[DEBUG] SF: Successfully written 2 bytes @ 0x800000
[DEBUG] SF: Successfully written 2 bytes @ 0x800002
[DEBUG] SF: Successfully written 20 bytes @ 0x800050
[DEBUG] SF: Successfully written 1588 bytes @ 0x800064
[DEBUG] MRC: updated 'RW_MRC_CACHE'.
[DEBUG] CBMEM entry for DIMM info: 0x7ffdb000
[DEBUG] SMM Memory Map
[DEBUG] SMRAM : 0x80000000 0x800000
[DEBUG] Subregion 0: 0x80000000 0x300000
[DEBUG] Subregion 1: 0x80300000 0x100000
[DEBUG] Subregion 2: 0x80400000 0x400000
[DEBUG] Normal boot
[INFO ] CBFS: Found 'fallback/postcar' @0x4b540 size 0x5abc in mcache @0xfeff107c
[DEBUG] Loading module at 0x7ffcf000 with entry 0x7ffcf031. filesize: 0x56e0 memsize: 0xba18
[DEBUG] Processing 231 relocs. Offset value of 0x7dfcf000
[DEBUG] BS: romstage times (exec / console): total (unknown) / 2 ms
[NOTE ] coreboot-4.19-479-gdb0946239f Thu Feb 16 00:48:04 UTC 2023 x86_32 postcar starting (log level: 7)...
[DEBUG] Normal boot
[INFO ] CBFS: Found 'fallback/ramstage' @0x1d500 size 0x1e43f in mcache @0x7ffdd0dc
[DEBUG] Loading module at 0x7ff7b000 with entry 0x7ff7b000. filesize: 0x3c538 memsize: 0x52eb0
[DEBUG] Processing 4254 relocs. Offset value of 0x7bf7b000
[DEBUG] BS: postcar times (exec / console): total (unknown) / 0 ms
[NOTE ] coreboot-4.19-479-gdb0946239f Thu Feb 16 00:48:04 UTC 2023 x86_32 ramstage starting (log level: 7)...
[DEBUG] Normal boot
[INFO ] Enumerating buses...
[DEBUG] Root Device scanning...
[DEBUG] CPU_CLUSTER: 0 enabled
[DEBUG] DOMAIN: 0000 enabled
[DEBUG] DOMAIN: 0000 scanning...
[DEBUG] PCI: pci_scan_bus for bus 00
[DEBUG] PCI: 00:00.0 [8086/0154] enabled
[INFO ] PCI: Static device PCI: 00:01.0 not found, disabling it.
[DEBUG] PCI: 00:02.0 [8086/0166] enabled
[DEBUG] PCI: 00:04.0 [8086/0153] disabled
[DEBUG] PCI: 00:14.0 [8086/1e31] enabled
[DEBUG] PCI: 00:16.0 [8086/1e3a] enabled
[DEBUG] PCI: 00:16.1: Disabling device
[DEBUG] PCI: 00:16.2: Disabling device
[INFO ] PCI: Static device PCI: 00:16.3 not found, disabling it.
[DEBUG] PCI: 00:19.0 [8086/1502] enabled
[DEBUG] PCI: 00:1a.0 [8086/1e2d] enabled
[DEBUG] PCI: 00:1b.0 [8086/1e20] enabled
[INFO ] PCH: PCIe Root Port coalescing is enabled
[DEBUG] PCI: 00:1c.0 [8086/1e10] enabled
[DEBUG] PCI: 00:1c.1 [8086/1e12] enabled
[DEBUG] PCI: 00:1c.2 [8086/1e14] enabled
[DEBUG] PCI: 00:1c.3: Disabling device
[DEBUG] PCI: 00:1c.3 [8086/1e16] disabled
[DEBUG] PCI: 00:1c.4: Disabling device
[DEBUG] PCI: 00:1c.4: check set enabled
[DEBUG] PCI: 00:1c.5: Disabling device
[DEBUG] PCI: 00:1c.6: Disabling device
[DEBUG] PCI: 00:1c.7: Disabling device
[DEBUG] PCI: 00:1d.0 [8086/1e26] enabled
[DEBUG] PCI: 00:1e.0: Disabling device
[DEBUG] PCI: 00:1e.0 [8086/2448] disabled
[DEBUG] PCI: 00:1f.0 [8086/1e55] enabled
[DEBUG] PCI: 00:1f.2 [8086/1e01] enabled
[DEBUG] PCI: 00:1f.3 [8086/1e22] enabled
[DEBUG] PCI: 00:1f.5: Disabling device
[DEBUG] PCI: 00:1f.5 [8086/1e09] disabled No operations
[DEBUG] PCI: 00:1f.6: Disabling device
[DEBUG] PCI: 00:1f.6 [8086/1e24] disabled No operations
[WARN ] PCI: Leftover static devices:
[WARN ] PCI: 00:01.0
[WARN ] PCI: 00:01.1
[WARN ] PCI: 00:01.2
[WARN ] PCI: 00:06.0
[WARN ] PCI: 00:16.1
[WARN ] PCI: 00:16.2
[WARN ] PCI: 00:16.3
[WARN ] PCI: 00:1c.4
[WARN ] PCI: 00:1c.5
[WARN ] PCI: 00:1c.6
[WARN ] PCI: 00:1c.7
[WARN ] PCI: Check your devicetree.cb.
[DEBUG] PCI: 00:1c.0 scanning...
[DEBUG] PCI: pci_scan_bus for bus 01
[DEBUG] PCI: 01:00.0 [1180/e823] enabled
[DEBUG] PCI: 01:00.3 [1180/e832] enabled
[INFO ] Enabling Common Clock Configuration
[INFO ] ASPM: Enabled L0s and L1
[INFO ] PCIe: Max_Payload_Size adjusted to 128
[DEBUG] PCI: 01:00.0: No LTR support
[INFO ] Enabling Common Clock Configuration
[INFO ] ASPM: Enabled L0s and L1
[INFO ] PCIe: Max_Payload_Size adjusted to 128
[DEBUG] PCI: 01:00.3: No LTR support
[DEBUG] scan_bus: bus PCI: 00:1c.0 finished in 0 msecs
[DEBUG] PCI: 00:1c.1 scanning...
[DEBUG] PCI: pci_scan_bus for bus 02
[DEBUG] PCI: 02:00.0 [168c/002a] enabled
[INFO ] Enabling Common Clock Configuration
[INFO ] ASPM: Enabled L0s and L1
[INFO ] PCIe: Max_Payload_Size adjusted to 128
[DEBUG] PCI: 02:00.0: No LTR support
[DEBUG] scan_bus: bus PCI: 00:1c.1 finished in 0 msecs
[DEBUG] PCI: 00:1c.2 scanning...
[DEBUG] PCI: pci_scan_bus for bus 03
[DEBUG] scan_bus: bus PCI: 00:1c.2 finished in 0 msecs
[DEBUG] PCI: 00:1f.0 scanning...
[INFO ] PMH7: ID 05 Revision 12
[DEBUG] PNP: 00ff.1 enabled
[DEBUG] PNP: 0c31.0 enabled
[INFO ] H8: EC Firmware ID G4HT40WW-3.22, Version 4.01B
[INFO ] H8: WWAN detection not implemented. Assuming WWAN installed
[DEBUG] PNP: 00ff.2 enabled
[DEBUG] Hybrid graphics: Switching panel to integrated GPU.
[DEBUG] PNP: 00ff.f disabled
[DEBUG] scan_bus: bus PCI: 00:1f.0 finished in 2 msecs
[DEBUG] PCI: 00:1f.3 scanning...
[DEBUG] I2C: 01:54 enabled
[DEBUG] bus: PCI: 00:1f.3[0]->I2C: 01:55 enabled
[DEBUG] bus: PCI: 00:1f.3[0]->I2C: 01:56 enabled
[DEBUG] bus: PCI: 00:1f.3[0]->I2C: 01:57 enabled
[DEBUG] bus: PCI: 00:1f.3[0]->I2C: 01:5c enabled
[DEBUG] bus: PCI: 00:1f.3[0]->I2C: 01:5d enabled
[DEBUG] bus: PCI: 00:1f.3[0]->I2C: 01:5e enabled
[DEBUG] bus: PCI: 00:1f.3[0]->I2C: 01:5f enabled
[DEBUG] bus: PCI: 00:1f.3[0]->scan_bus: bus PCI: 00:1f.3 finished in 0 msecs
[DEBUG] scan_bus: bus DOMAIN: 0000 finished in 4 msecs
[DEBUG] scan_bus: bus Root Device finished in 4 msecs
[INFO ] done
[DEBUG] BS: BS_DEV_ENUMERATE run times (exec / console): 4 / 0 ms
[DEBUG] found VGA at PCI: 00:02.0
[DEBUG] Setting up VGA for PCI: 00:02.0
[DEBUG] Setting PCI_BRIDGE_CTL_VGA for bridge DOMAIN: 0000
[DEBUG] Setting PCI_BRIDGE_CTL_VGA for bridge Root Device
[INFO ] Allocating resources...
[INFO ] Reading resources...
[DEBUG] Adding PCIe enhanced config space BAR 0xf0000000-0xf4000000.
[DEBUG] TOUUD 0x17d600000 TOLUD 0x82a00000 TOM 0x100000000
[DEBUG] MEBASE 0x7ffff00000
[DEBUG] IGD decoded, subtracting 32M UMA and 2M GTT
[DEBUG] TSEG base 0x80000000 size 8M
[INFO ] Available memory below 4GB: 2048M
[INFO ] Available memory above 4GB: 2006M
[ERROR] PNP: 00ff.1 missing read_resources
[ERROR] PNP: 00ff.2 missing read_resources
[INFO ] Done reading resources.
[INFO ] === Resource allocator: DOMAIN: 0000 - Pass 1 (gathering requirements) ===
[DEBUG] PCI: 00:1c.0 io: size: 0 align: 12 gran: 12 limit: ffff
[DEBUG] PCI: 00:1c.0 io: size: 0 align: 12 gran: 12 limit: ffff done
[DEBUG] PCI: 00:1c.0 mem: size: 0 align: 20 gran: 20 limit: ffffffff
[DEBUG] PCI: 01:00.3 10 * [0x0 - 0x7ff] mem
[DEBUG] PCI: 01:00.0 10 * [0x1000 - 0x10ff] mem
[DEBUG] PCI: 00:1c.0 mem: size: 100000 align: 20 gran: 20 limit: ffffffff done
[DEBUG] PCI: 00:1c.0 prefmem: size: 0 align: 20 gran: 20 limit: ffffffffffffffff
[DEBUG] PCI: 00:1c.0 prefmem: size: 0 align: 20 gran: 20 limit: ffffffffffffffff done
[DEBUG] PCI: 00:1c.1 io: size: 0 align: 12 gran: 12 limit: ffff
[DEBUG] PCI: 00:1c.1 io: size: 0 align: 12 gran: 12 limit: ffff done
[DEBUG] PCI: 00:1c.1 mem: size: 0 align: 20 gran: 20 limit: ffffffff
[DEBUG] PCI: 02:00.0 10 * [0x0 - 0xffff] mem
[DEBUG] PCI: 00:1c.1 mem: size: 100000 align: 20 gran: 20 limit: ffffffff done
[DEBUG] PCI: 00:1c.1 prefmem: size: 0 align: 20 gran: 20 limit: ffffffffffffffff
[DEBUG] PCI: 00:1c.1 prefmem: size: 0 align: 20 gran: 20 limit: ffffffffffffffff done
[DEBUG] PCI: 00:1c.2 io: size: 0 align: 12 gran: 12 limit: ffff
[DEBUG] NONE 18 * [0x0 - 0x1fff] io
[DEBUG] PCI: 00:1c.2 io: size: 2000 align: 12 gran: 12 limit: ffff done
[DEBUG] PCI: 00:1c.2 mem: size: 0 align: 20 gran: 20 limit: ffffffff
[DEBUG] NONE 10 * [0x0 - 0x7fffff] mem
[DEBUG] PCI: 00:1c.2 mem: size: 800000 align: 20 gran: 20 limit: ffffffff done
[DEBUG] PCI: 00:1c.2 prefmem: size: 0 align: 20 gran: 20 limit: ffffffffffffffff
[DEBUG] NONE 14 * [0x0 - 0xfffffff] prefmem
[DEBUG] PCI: 00:1c.2 prefmem: size: 10000000 align: 20 gran: 20 limit: ffffffffffffffff done
[INFO ] === Resource allocator: DOMAIN: 0000 - Pass 2 (allocating resources) ===
[DEBUG] DOMAIN: 0000 io: base: 0 size: 0 align: 0 gran: 0 limit: ffff
[DEBUG] update_constraints: PCI: 00:1f.0 10000000 base 00000000 limit 00000fff io (fixed)
[DEBUG] update_constraints: PCI: 00:1f.0 10000200 base 00001600 limit 0000167b io (fixed)
[DEBUG] update_constraints: PCI: 00:1f.0 10000300 base 000015e0 limit 000015eb io (fixed)
[DEBUG] update_constraints: PNP: 00ff.1 77 base 000015e0 limit 000015ef io (fixed)
[DEBUG] update_constraints: PCI: 00:1f.3 20 base 00000400 limit 0000041f io (fixed)
[INFO ] DOMAIN: 0000: Resource ranges:
[INFO ] * Base: 1000, Size: 5e0, Tag: 100
[INFO ] * Base: 15f0, Size: 10, Tag: 100
[INFO ] * Base: 167c, Size: e984, Tag: 100
[DEBUG] PCI: 00:1c.2 1c * [0x2000 - 0x3fff] limit: 3fff io
[DEBUG] PCI: 00:02.0 20 * [0x1000 - 0x103f] limit: 103f io
[DEBUG] PCI: 00:19.0 18 * [0x1040 - 0x105f] limit: 105f io
[DEBUG] PCI: 00:1f.2 20 * [0x1060 - 0x107f] limit: 107f io
[DEBUG] PCI: 00:1f.2 10 * [0x1080 - 0x1087] limit: 1087 io
[DEBUG] PCI: 00:1f.2 18 * [0x1088 - 0x108f] limit: 108f io
[DEBUG] PCI: 00:1f.2 14 * [0x1090 - 0x1093] limit: 1093 io
[DEBUG] PCI: 00:1f.2 1c * [0x1094 - 0x1097] limit: 1097 io
[DEBUG] DOMAIN: 0000 io: base: 0 size: 0 align: 0 gran: 0 limit: ffff done
[DEBUG] DOMAIN: 0000 mem: base: 0 size: 0 align: 0 gran: 0 limit: fffffffff
[DEBUG] update_constraints: PCI: 00:00.0 60 base f0000000 limit f3ffffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 03 base 00000000 limit 0009ffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 04 base 00100000 limit 7fffffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 05 base 100000000 limit 17d5fffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 06 base 80000000 limit 829fffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 07 base 000a0000 limit 000bffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 08 base 000c0000 limit 000fffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 09 base fed90000 limit fed90fff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 0a base fed91000 limit fed91fff mem (fixed)
[DEBUG] update_constraints: PCI: 00:1f.0 10000100 base ff000000 limit ffffffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:1f.0 03 base fec00000 limit fec00fff mem (fixed)
[DEBUG] update_constraints: PNP: 0c31.0 00 base fed40000 limit fed44fff mem (fixed)
[INFO ] DOMAIN: 0000: Resource ranges:
[INFO ] * Base: 82a00000, Size: 6d600000, Tag: 200
[INFO ] * Base: f4000000, Size: ac00000, Tag: 200
[INFO ] * Base: fec01000, Size: 13f000, Tag: 200
[INFO ] * Base: fed45000, Size: 4b000, Tag: 200
[INFO ] * Base: fed92000, Size: 26e000, Tag: 200
[INFO ] * Base: 17d600000, Size: e82a00000, Tag: 100200
[DEBUG] PCI: 00:02.0 18 * [0x90000000 - 0x9fffffff] limit: 9fffffff prefmem
[DEBUG] PCI: 00:02.0 10 * [0x82c00000 - 0x82ffffff] limit: 82ffffff mem
[DEBUG] PCI: 00:1c.2 20 * [0x83000000 - 0x837fffff] limit: 837fffff mem
[DEBUG] PCI: 00:1c.0 20 * [0x82a00000 - 0x82afffff] limit: 82afffff mem
[DEBUG] PCI: 00:1c.1 20 * [0x82b00000 - 0x82bfffff] limit: 82bfffff mem
[DEBUG] PCI: 00:19.0 10 * [0x83800000 - 0x8381ffff] limit: 8381ffff mem
[DEBUG] PCI: 00:14.0 10 * [0x83820000 - 0x8382ffff] limit: 8382ffff mem
[DEBUG] PCI: 00:1b.0 10 * [0x83830000 - 0x83833fff] limit: 83833fff mem
[DEBUG] PCI: 00:19.0 14 * [0x83834000 - 0x83834fff] limit: 83834fff mem
[DEBUG] PCI: 00:1f.2 24 * [0x83835000 - 0x838357ff] limit: 838357ff mem
[DEBUG] PCI: 00:1a.0 10 * [0x83836000 - 0x838363ff] limit: 838363ff mem
[DEBUG] PCI: 00:1d.0 10 * [0x83837000 - 0x838373ff] limit: 838373ff mem
[DEBUG] PCI: 00:1f.3 10 * [0x83838000 - 0x838380ff] limit: 838380ff mem
[DEBUG] PCI: 00:16.0 10 * [0x83839000 - 0x8383900f] limit: 8383900f mem
[DEBUG] PCI: 00:1c.2 24 * [0x17d600000 - 0x18d5fffff] limit: 18d5fffff prefmem
[DEBUG] DOMAIN: 0000 mem: base: 0 size: 0 align: 0 gran: 0 limit: fffffffff done
[DEBUG] PCI: 00:1c.0 mem: base: 82a00000 size: 100000 align: 20 gran: 20 limit: 82afffff
[INFO ] PCI: 00:1c.0: Resource ranges:
[INFO ] * Base: 82a00000, Size: 100000, Tag: 200
[DEBUG] PCI: 01:00.3 10 * [0x82a00000 - 0x82a007ff] limit: 82a007ff mem
[DEBUG] PCI: 01:00.0 10 * [0x82a01000 - 0x82a010ff] limit: 82a010ff mem
[DEBUG] PCI: 00:1c.0 mem: base: 82a00000 size: 100000 align: 20 gran: 20 limit: 82afffff done
[DEBUG] PCI: 00:1c.1 mem: base: 82b00000 size: 100000 align: 20 gran: 20 limit: 82bfffff
[INFO ] PCI: 00:1c.1: Resource ranges:
[INFO ] * Base: 82b00000, Size: 100000, Tag: 200
[DEBUG] PCI: 02:00.0 10 * [0x82b00000 - 0x82b0ffff] limit: 82b0ffff mem
[DEBUG] PCI: 00:1c.1 mem: base: 82b00000 size: 100000 align: 20 gran: 20 limit: 82bfffff done
[DEBUG] PCI: 00:1c.2 io: base: 2000 size: 2000 align: 12 gran: 12 limit: 3fff
[INFO ] PCI: 00:1c.2: Resource ranges:
[INFO ] * Base: 2000, Size: 2000, Tag: 100
[DEBUG] NONE 18 * [0x2000 - 0x3fff] limit: 3fff io
[DEBUG] PCI: 00:1c.2 io: base: 2000 size: 2000 align: 12 gran: 12 limit: 3fff done
[DEBUG] PCI: 00:1c.2 prefmem: base: 17d600000 size: 10000000 align: 20 gran: 20 limit: 18d5fffff
[INFO ] PCI: 00:1c.2: Resource ranges:
[INFO ] * Base: 17d600000, Size: 10000000, Tag: 1200
[DEBUG] NONE 14 * [0x17d600000 - 0x18d5fffff] limit: 18d5fffff prefmem
[DEBUG] PCI: 00:1c.2 prefmem: base: 17d600000 size: 10000000 align: 20 gran: 20 limit: 18d5fffff done
[DEBUG] PCI: 00:1c.2 mem: base: 83000000 size: 800000 align: 20 gran: 20 limit: 837fffff
[INFO ] PCI: 00:1c.2: Resource ranges:
[INFO ] * Base: 83000000, Size: 800000, Tag: 200
[DEBUG] NONE 10 * [0x83000000 - 0x837fffff] limit: 837fffff mem
[DEBUG] PCI: 00:1c.2 mem: base: 83000000 size: 800000 align: 20 gran: 20 limit: 837fffff done
[INFO ] === Resource allocator: DOMAIN: 0000 - resource allocation complete ===
[DEBUG] PCI: 00:02.0 10 <- [0x0000000082c00000 - 0x0000000082ffffff] size 0x00400000 gran 0x16 mem64
[DEBUG] PCI: 00:02.0 18 <- [0x0000000090000000 - 0x000000009fffffff] size 0x10000000 gran 0x1c prefmem64
[DEBUG] PCI: 00:02.0 20 <- [0x0000000000001000 - 0x000000000000103f] size 0x00000040 gran 0x06 io
[DEBUG] PCI: 00:14.0 10 <- [0x0000000083820000 - 0x000000008382ffff] size 0x00010000 gran 0x10 mem64
[DEBUG] PCI: 00:16.0 10 <- [0x0000000083839000 - 0x000000008383900f] size 0x00000010 gran 0x04 mem64
[DEBUG] PCI: 00:19.0 10 <- [0x0000000083800000 - 0x000000008381ffff] size 0x00020000 gran 0x11 mem
[DEBUG] PCI: 00:19.0 14 <- [0x0000000083834000 - 0x0000000083834fff] size 0x00001000 gran 0x0c mem
[DEBUG] PCI: 00:19.0 18 <- [0x0000000000001040 - 0x000000000000105f] size 0x00000020 gran 0x05 io
[DEBUG] PCI: 00:1a.0 10 <- [0x0000000083836000 - 0x00000000838363ff] size 0x00000400 gran 0x0a mem
[DEBUG] PCI: 00:1b.0 10 <- [0x0000000083830000 - 0x0000000083833fff] size 0x00004000 gran 0x0e mem64
[DEBUG] PCI: 00:1c.0 1c <- [0x000000000000ffff - 0x000000000000fffe] size 0x00000000 gran 0x0c bus 01 io
[DEBUG] PCI: 00:1c.0 24 <- [0xffffffffffffffff - 0xfffffffffffffffe] size 0x00000000 gran 0x14 bus 01 prefmem
[DEBUG] PCI: 00:1c.0 20 <- [0x0000000082a00000 - 0x0000000082afffff] size 0x00100000 gran 0x14 bus 01 mem
[DEBUG] PCI: 01:00.0 10 <- [0x0000000082a01000 - 0x0000000082a010ff] size 0x00000100 gran 0x08 mem
[DEBUG] PCI: 01:00.3 10 <- [0x0000000082a00000 - 0x0000000082a007ff] size 0x00000800 gran 0x0b mem
[DEBUG] PCI: 00:1c.1 1c <- [0x000000000000ffff - 0x000000000000fffe] size 0x00000000 gran 0x0c bus 02 io
[DEBUG] PCI: 00:1c.1 24 <- [0xffffffffffffffff - 0xfffffffffffffffe] size 0x00000000 gran 0x14 bus 02 prefmem
[DEBUG] PCI: 00:1c.1 20 <- [0x0000000082b00000 - 0x0000000082bfffff] size 0x00100000 gran 0x14 bus 02 mem
[DEBUG] PCI: 02:00.0 10 <- [0x0000000082b00000 - 0x0000000082b0ffff] size 0x00010000 gran 0x10 mem64
[DEBUG] PCI: 00:1c.2 1c <- [0x0000000000002000 - 0x0000000000003fff] size 0x00002000 gran 0x0c bus 03 io
[DEBUG] PCI: 00:1c.2 24 <- [0x000000017d600000 - 0x000000018d5fffff] size 0x10000000 gran 0x14 bus 03 prefmem
[DEBUG] PCI: 00:1c.2 20 <- [0x0000000083000000 - 0x00000000837fffff] size 0x00800000 gran 0x14 bus 03 mem
[DEBUG] PCI: 00:1d.0 10 <- [0x0000000083837000 - 0x00000000838373ff] size 0x00000400 gran 0x0a mem
[ERROR] PNP: 00ff.1 missing set_resources
[ERROR] PNP: 00ff.2 missing set_resources
[DEBUG] PCI: 00:1f.2 10 <- [0x0000000000001080 - 0x0000000000001087] size 0x00000008 gran 0x03 io
[DEBUG] PCI: 00:1f.2 14 <- [0x0000000000001090 - 0x0000000000001093] size 0x00000004 gran 0x02 io
[DEBUG] PCI: 00:1f.2 18 <- [0x0000000000001088 - 0x000000000000108f] size 0x00000008 gran 0x03 io
[DEBUG] PCI: 00:1f.2 1c <- [0x0000000000001094 - 0x0000000000001097] size 0x00000004 gran 0x02 io
[DEBUG] PCI: 00:1f.2 20 <- [0x0000000000001060 - 0x000000000000107f] size 0x00000020 gran 0x05 io
[DEBUG] PCI: 00:1f.2 24 <- [0x0000000083835000 - 0x00000000838357ff] size 0x00000800 gran 0x0b mem
[DEBUG] PCI: 00:1f.3 10 <- [0x0000000083838000 - 0x00000000838380ff] size 0x00000100 gran 0x08 mem64
[INFO ] Done setting resources.
[INFO ] Done allocating resources.
[DEBUG] BS: BS_DEV_RESOURCES run times (exec / console): 3 / 0 ms
[INFO ] Enabling resources...
[DEBUG] PCI: 00:00.0 subsystem <- 8086/0154
[DEBUG] PCI: 00:00.0 cmd <- 06
[DEBUG] PCI: 00:02.0 subsystem <- 17aa/21f5
[DEBUG] PCI: 00:02.0 cmd <- 03
[DEBUG] PCI: 00:14.0 subsystem <- 8086/1e31
[DEBUG] PCI: 00:14.0 cmd <- 102
[DEBUG] PCI: 00:16.0 subsystem <- 8086/1e3a
[DEBUG] PCI: 00:16.0 cmd <- 02
[DEBUG] PCI: 00:19.0 subsystem <- 17aa/21f3
[DEBUG] PCI: 00:19.0 cmd <- 103
[DEBUG] PCI: 00:1a.0 subsystem <- 8086/1e2d
[DEBUG] PCI: 00:1a.0 cmd <- 102
[DEBUG] PCI: 00:1b.0 subsystem <- 8086/1e20
[DEBUG] PCI: 00:1b.0 cmd <- 102
[DEBUG] PCI: 00:1c.0 bridge ctrl <- 0013
[DEBUG] PCI: 00:1c.0 subsystem <- 8086/1e10
[DEBUG] PCI: 00:1c.0 cmd <- 106
[DEBUG] PCI: 00:1c.1 bridge ctrl <- 0013
[DEBUG] PCI: 00:1c.1 subsystem <- 8086/1e12
[DEBUG] PCI: 00:1c.1 cmd <- 106
[DEBUG] PCI: 00:1c.2 bridge ctrl <- 0013
[DEBUG] PCI: 00:1c.2 subsystem <- 8086/1e14
[DEBUG] PCI: 00:1c.2 cmd <- 107
[DEBUG] PCI: 00:1d.0 subsystem <- 8086/1e26
[DEBUG] PCI: 00:1d.0 cmd <- 102
[DEBUG] PCI: 00:1f.0 subsystem <- 8086/1e55
[DEBUG] PCI: 00:1f.0 cmd <- 107
[DEBUG] PCI: 00:1f.2 subsystem <- 8086/1e03
[DEBUG] PCI: 00:1f.2 cmd <- 03
[DEBUG] PCI: 00:1f.3 subsystem <- 8086/1e22
[DEBUG] PCI: 00:1f.3 cmd <- 103
[DEBUG] PCI: 01:00.0 subsystem <- 1180/e823
[DEBUG] PCI: 01:00.0 cmd <- 06
[DEBUG] PCI: 01:00.3 cmd <- 02
[DEBUG] PCI: 02:00.0 cmd <- 02
[INFO ] done.
[INFO ] Initializing devices...
[DEBUG] CPU_CLUSTER: 0 init
[DEBUG] MTRR: Physical address space:
[DEBUG] 0x0000000000000000 - 0x000000000009ffff size 0x000a0000 type 6
[DEBUG] 0x00000000000a0000 - 0x00000000000bffff size 0x00020000 type 0
[DEBUG] 0x00000000000c0000 - 0x000000007fffffff size 0x7ff40000 type 6
[DEBUG] 0x0000000080000000 - 0x000000008fffffff size 0x10000000 type 0
[DEBUG] 0x0000000090000000 - 0x000000009fffffff size 0x10000000 type 1
[DEBUG] 0x00000000a0000000 - 0x00000000ffffffff size 0x60000000 type 0
[DEBUG] 0x0000000100000000 - 0x000000017d5fffff size 0x7d600000 type 6
[DEBUG] 0x000000017d600000 - 0x000000018d5fffff size 0x10000000 type 0
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x250 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x258 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x259 0x0000000000000000
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x268 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x269 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x26a 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x26b 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x26c 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x26d 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x26e 0x0606060606060606
[DEBUG] apic_id 0x0: MTRR: Fixed MSR 0x26f 0x0606060606060606
[DEBUG] apic_id 0x0 setup mtrr for CPU physical address size: 36 bits
[DEBUG] MTRR: default type WB/UC MTRR counts: 12/6.
[DEBUG] MTRR: UC selected as default type.
[DEBUG] MTRR: 0 base 0x0000000000000000 mask 0x0000000f80000000 type 6
[DEBUG] MTRR: 1 base 0x0000000090000000 mask 0x0000000ff0000000 type 1
[DEBUG] MTRR: 2 base 0x0000000100000000 mask 0x0000000f80000000 type 6
[DEBUG] MTRR: 3 base 0x000000017d600000 mask 0x0000000fffe00000 type 0
[DEBUG] MTRR: 4 base 0x000000017d800000 mask 0x0000000fff800000 type 0
[DEBUG] MTRR: 5 base 0x000000017e000000 mask 0x0000000ffe000000 type 0
[DEBUG] MTRR check
[DEBUG] Fixed MTRRs : Enabled
[DEBUG] Variable MTRRs: Enabled
[DEBUG] CPU has 4 cores, 8 threads enabled.
[DEBUG] Setting up SMI for CPU
[INFO ] Will perform SMM setup.
[INFO ] CBFS: Found 'cpu_microcode_blob.bin' @0x16cc0 size 0x6800 in mcache @0x7ffdd0ac
[DEBUG] microcode: sig=0x306a9 pf=0x10 revision=0x21
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[INFO ] LAPIC 0x0 in XAPIC mode.
[DEBUG] CPU: APIC: 00 enabled
[DEBUG] CPU: APIC: 01 enabled
[DEBUG] CPU: APIC: 02 enabled
[DEBUG] CPU: APIC: 03 enabled
[DEBUG] CPU: APIC: 04 enabled
[DEBUG] CPU: APIC: 05 enabled
[DEBUG] CPU: APIC: 06 enabled
[DEBUG] CPU: APIC: 07 enabled
[DEBUG] Loading module at 0x00030000 with entry 0x00030000. filesize: 0x178 memsize: 0x178
[DEBUG] Processing 16 relocs. Offset value of 0x00030000
[DEBUG] Attempting to start 7 APs
[DEBUG] Waiting for 10ms after sending INIT.
[DEBUG] Waiting for SIPI to complete...
[DEBUG] done.
[DEBUG] Waiting for SIPI to complete...
[INFO ] LAPIC 0x1 in XAPIC mode.
[DEBUG] done.
[INFO ] AP: slot 1 apic_id 1, MCU rev: 0x00000021
[INFO ] LAPIC 0x5 in XAPIC mode.
[INFO ] AP: slot 2 apic_id 5, MCU rev: 0x00000021
[INFO ] LAPIC 0x4 in XAPIC mode.
[INFO ] AP: slot 3 apic_id 4, MCU rev: 0x00000021
[INFO ] LAPIC 0x6 in XAPIC mode.
[INFO ] AP: slot 4 apic_id 6, MCU rev: 0x00000021
[INFO ] LAPIC 0x7 in XAPIC mode.
[INFO ] LAPIC 0x2 in XAPIC mode.
[INFO ] LAPIC 0x3 in XAPIC mode.
[INFO ] AP: slot 6 apic_id 2, MCU rev: 0x00000021
[INFO ] AP: slot 7 apic_id 3, MCU rev: 0x00000021
[INFO ] AP: slot 5 apic_id 7, MCU rev: 0x00000021
[DEBUG] Loading module at 0x00038000 with entry 0x00038000. filesize: 0x1e8 memsize: 0x1e8
[DEBUG] Processing 11 relocs. Offset value of 0x00038000
[DEBUG] smm_module_setup_stub: stack_top = 0x80002000
[DEBUG] smm_module_setup_stub: per cpu stack_size = 0x400
[DEBUG] smm_module_setup_stub: runtime.start32_offset = 0x4c
[DEBUG] smm_module_setup_stub: runtime.smm_size = 0x10000
[DEBUG] SMM Module: stub loaded at 38000. Will call 0x7ff9bbc7
[DEBUG] Installing permanent SMM handler to 0x80000000
[DEBUG] FX_SAVE [0x802ff000-0x80300000]
[DEBUG] HANDLER [0x802fc000-0x802fe038]
[DEBUG] CPU 0
[DEBUG] ss0 [0x802fbc00-0x802fc000]
[DEBUG] stub0 [0x802f4000-0x802f41e8]
[DEBUG] CPU 1
[DEBUG] ss1 [0x802fb800-0x802fbc00]
[DEBUG] stub1 [0x802f3c00-0x802f3de8]
[DEBUG] CPU 2
[DEBUG] ss2 [0x802fb400-0x802fb800]
[DEBUG] stub2 [0x802f3800-0x802f39e8]
[DEBUG] CPU 3
[DEBUG] ss3 [0x802fb000-0x802fb400]
[DEBUG] stub3 [0x802f3400-0x802f35e8]
[DEBUG] CPU 4
[DEBUG] ss4 [0x802fac00-0x802fb000]
[DEBUG] stub4 [0x802f3000-0x802f31e8]
[DEBUG] CPU 5
[DEBUG] ss5 [0x802fa800-0x802fac00]
[DEBUG] stub5 [0x802f2c00-0x802f2de8]
[DEBUG] CPU 6
[DEBUG] ss6 [0x802fa400-0x802fa800]
[DEBUG] stub6 [0x802f2800-0x802f29e8]
[DEBUG] CPU 7
[DEBUG] ss7 [0x802fa000-0x802fa400]
[DEBUG] stub7 [0x802f2400-0x802f25e8]
[DEBUG] stacks [0x80000000-0x80002000]
[DEBUG] Loading module at 0x802fc000 with entry 0x802fc7bd. filesize: 0x1ff0 memsize: 0x2038
[DEBUG] Processing 91 relocs. Offset value of 0x802fc000
[DEBUG] Loading module at 0x802f4000 with entry 0x802f4000. filesize: 0x1e8 memsize: 0x1e8
[DEBUG] Processing 11 relocs. Offset value of 0x802f4000
[DEBUG] smm_module_setup_stub: stack_top = 0x80002000
[DEBUG] smm_module_setup_stub: per cpu stack_size = 0x400
[DEBUG] smm_module_setup_stub: runtime.start32_offset = 0x4c
[DEBUG] smm_module_setup_stub: runtime.smm_size = 0x300000
[DEBUG] SMM Module: placing smm entry code at 802f3c00, cpu # 0x1
[DEBUG] SMM Module: placing smm entry code at 802f3800, cpu # 0x2
[DEBUG] SMM Module: placing smm entry code at 802f3400, cpu # 0x3
[DEBUG] SMM Module: placing smm entry code at 802f3000, cpu # 0x4
[DEBUG] SMM Module: placing smm entry code at 802f2c00, cpu # 0x5
[DEBUG] SMM Module: placing smm entry code at 802f2800, cpu # 0x6
[DEBUG] SMM Module: placing smm entry code at 802f2400, cpu # 0x7
[DEBUG] SMM Module: stub loaded at 802f4000. Will call 0x802fc7bd
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x802ec000, cpu = 0
[DEBUG] In relocation handler: cpu 0
[DEBUG] New SMBASE=0x802ec000 IEDBASE=0x80400000
[DEBUG] Writing SMRR. base = 0x80000006, mask=0xff800800
[DEBUG] Relocation complete.
[INFO ] microcode: Update skipped, already up-to-date
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x802ebc00, cpu = 1
[DEBUG] In relocation handler: cpu 1
[DEBUG] New SMBASE=0x802ebc00 IEDBASE=0x80400000
[DEBUG] Writing SMRR. base = 0x80000006, mask=0xff800800
[DEBUG] Relocation complete.
[INFO ] microcode: Update skipped, already up-to-date
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x802ea800, cpu = 6
[DEBUG] In relocation handler: cpu 6
[DEBUG] New SMBASE=0x802ea800 IEDBASE=0x80400000
[DEBUG] Writing SMRR. base = 0x80000006, mask=0xff800800
[DEBUG] Relocation complete.
[INFO ] microcode: Update skipped, already up-to-date
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x802ea400, cpu = 7
[DEBUG] In relocation handler: cpu 7
[DEBUG] New SMBASE=0x802ea400 IEDBASE=0x80400000
[DEBUG] Writing SMRR. base = 0x80000006, mask=0xff800800
[DEBUG] Relocation complete.
[INFO ] microcode: Update skipped, already up-to-date
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x802eac00, cpu = 5
[DEBUG] In relocation handler: cpu 5
[DEBUG] New SMBASE=0x802eac00 IEDBASE=0x80400000
[DEBUG] Writing SMRR. base = 0x80000006, mask=0xff800800
[DEBUG] Relocation complete.
[INFO ] microcode: Update skipped, already up-to-date
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x802eb000, cpu = 4
[DEBUG] In relocation handler: cpu 4
[DEBUG] New SMBASE=0x802eb000 IEDBASE=0x80400000
[DEBUG] Writing SMRR. base = 0x80000006, mask=0xff800800
[DEBUG] Relocation complete.
[INFO ] microcode: Update skipped, already up-to-date
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x802eb400, cpu = 3
[DEBUG] In relocation handler: cpu 3
[DEBUG] New SMBASE=0x802eb400 IEDBASE=0x80400000
[DEBUG] Writing SMRR. base = 0x80000006, mask=0xff800800
[DEBUG] Relocation complete.
[INFO ] microcode: Update skipped, already up-to-date
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x802eb800, cpu = 2
[DEBUG] In relocation handler: cpu 2
[DEBUG] New SMBASE=0x802eb800 IEDBASE=0x80400000
[DEBUG] Writing SMRR. base = 0x80000006, mask=0xff800800
[DEBUG] Relocation complete.
[INFO ] microcode: Update skipped, already up-to-date
[INFO ] Initializing CPU #0
[DEBUG] CPU: vendor Intel device 306a9
[DEBUG] CPU: family 06, model 3a, stepping 09
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[INFO ] CPU: platform id 4
[INFO ] CPU: cpuid(1) 0x306a9
[INFO ] CPU: AES supported
[INFO ] CPU: TXT supported
[INFO ] CPU: VT supported
[DEBUG] VMX status: enabled
[DEBUG] IA32_FEATURE_CONTROL status: locked
[DEBUG] cpu: energy policy set to 6
[DEBUG] model_x06ax: frequency set to 2700
[INFO ] Turbo is available but hidden
[INFO ] Turbo is available and visible
[INFO ] CPU #0 initialized
[INFO ] Initializing CPU #1
[INFO ] Initializing CPU #4
[INFO ] Initializing CPU #5
[DEBUG] CPU: vendor Intel device 306a9
[DEBUG] CPU: family 06, model 3a, stepping 09
[DEBUG] CPU: vendor Intel device 306a9
[DEBUG] CPU: family 06, model 3a, stepping 09
[INFO ] Initializing CPU #2
[INFO ] Initializing CPU #3
[DEBUG] CPU: vendor Intel device 306a9
[DEBUG] CPU: family 06, model 3a, stepping 09
[DEBUG] CPU: vendor Intel device 306a9
[DEBUG] CPU: family 06, model 3a, stepping 09
[INFO ] Initializing CPU #6
[INFO ] Initializing CPU #7
[DEBUG] CPU: vendor Intel device 306a9
[DEBUG] CPU: family 06, model 3a, stepping 09
[DEBUG] CPU: vendor Intel device 306a9
[DEBUG] CPU: family 06, model 3a, stepping 09
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[INFO ] CPU: platform id 4
[INFO ] CPU: platform id 4
[INFO ] CPU: cpuid(1) 0x306a9
[INFO ] CPU: cpuid(1) 0x306a9
[INFO ] CPU: AES supported
[INFO ] CPU: TXT supported
[INFO ] CPU: VT supported
[INFO ] CPU: AES supported
[DEBUG] VMX status: enabled
[INFO ] CPU: TXT supported
[INFO ] CPU: VT supported
[DEBUG] IA32_FEATURE_CONTROL status: locked
[DEBUG] VMX status: enabled
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[INFO ] CPU: platform id 4
[INFO ] CPU: platform id 4
[INFO ] CPU: cpuid(1) 0x306a9
[INFO ] CPU: cpuid(1) 0x306a9
[INFO ] CPU: AES supported
[INFO ] CPU: TXT supported
[INFO ] CPU: VT supported
[INFO ] CPU: AES supported
[INFO ] CPU: TXT supported
[INFO ] CPU: VT supported
[DEBUG] VMX status: enabled
[DEBUG] VMX status: enabled
[DEBUG] IA32_FEATURE_CONTROL status: locked
[DEBUG] IA32_FEATURE_CONTROL status: locked
[DEBUG] CPU: vendor Intel device 306a9
[DEBUG] CPU: family 06, model 3a, stepping 09
[DEBUG] cpu: energy policy set to 6
[DEBUG] IA32_FEATURE_CONTROL status: locked
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[INFO ] CPU: platform id 4
[INFO ] CPU: platform id 4
[INFO ] CPU: cpuid(1) 0x306a9
[INFO ] CPU: cpuid(1) 0x306a9
[INFO ] CPU: Intel(R) Core(TM) i7-3820QM CPU @ 2.70GHz.
[DEBUG] model_x06ax: frequency set to 2700
[INFO ] CPU #4 initialized
[INFO ] CPU: AES supported
[INFO ] CPU: TXT supported
[INFO ] CPU: VT supported
[INFO ] CPU: AES supported
[INFO ] CPU: TXT supported
[INFO ] CPU: VT supported
[DEBUG] VMX status: enabled
[DEBUG] VMX status: enabled
[DEBUG] IA32_FEATURE_CONTROL status: locked
[DEBUG] IA32_FEATURE_CONTROL status: locked
[INFO ] CPU: platform id 4
[DEBUG] cpu: energy policy set to 6
[DEBUG] cpu: energy policy set to 6
[DEBUG] cpu: energy policy set to 6
[DEBUG] model_x06ax: frequency set to 2700
[INFO ] CPU #5 initialized
[INFO ] CPU: cpuid(1) 0x306a9
[DEBUG] model_x06ax: frequency set to 2700
[DEBUG] model_x06ax: frequency set to 2700
[INFO ] CPU #2 initialized
[INFO ] CPU #3 initialized
[INFO ] CPU: AES supported
[INFO ] CPU: TXT supported
[INFO ] CPU: VT supported
[DEBUG] cpu: energy policy set to 6
[DEBUG] cpu: energy policy set to 6
[DEBUG] VMX status: enabled
[DEBUG] model_x06ax: frequency set to 2700
[DEBUG] model_x06ax: frequency set to 2700
[INFO ] CPU #6 initialized
[INFO ] CPU #7 initialized
[DEBUG] IA32_FEATURE_CONTROL status: locked
[DEBUG] cpu: energy policy set to 6
[DEBUG] model_x06ax: frequency set to 2700
[INFO ] CPU #1 initialized
[INFO ] bsp_do_flight_plan done after 29 msecs.
[DEBUG] SMI_STS:
[DEBUG] GPE0_STS: GPIO15 GPIO14 GPIO11 GPIO9 GPIO7 GPIO5 GPIO4 GPIO3 GPIO0
[DEBUG] ALT_GP_SMI_STS: GPI14 GPI11 GPI9 GPI7 GPI5 GPI4 GPI3 GPI1 GPI0
[DEBUG] TCO_STS:
[DEBUG] Locking SMM.
[DEBUG] CPU_CLUSTER: 0 init finished in 44 msecs
[DEBUG] PCI: 00:00.0 init
[DEBUG] Disabling PEG12.
[DEBUG] Disabling PEG11.
[DEBUG] Disabling PEG10.
[DEBUG] Disabling Device 4.
[DEBUG] Disabling PEG60.
[DEBUG] Disabling Device 7.
[DEBUG] Disabling PEG IO clock.
[DEBUG] Set BIOS_RESET_CPL
[DEBUG] CPU TDP: 45 Watts
[DEBUG] PCI: 00:00.0 init finished in 1 msecs
[DEBUG] PCI: 00:02.0 init
[WARN ] CBFS: 'vbt.bin' not found.
[WARN ] CBFS: 'pci8086,0166.rom' not found.
[WARN ] CBFS: 'pci8086,0106.rom' not found.
[DEBUG] PCI Option ROM loading disabled for PCI: 00:02.0
[ERROR] GMA: VBT couldn't be found
[DEBUG] GT Power Management Init
[DEBUG] IVB GT2 35W Power Meter Weights
[DEBUG] GT Power Management Init (post VBIOS)
[INFO ] framebuffer_info: bytes_per_line: 4096, bits_per_pixel: 32
[INFO ] x_res x y_res: 1024 x 768, size: 3145728 at 0x90000000
[DEBUG] PCI: 00:02.0 init finished in 510 msecs
[DEBUG] PCI: 00:14.0 init
[DEBUG] XHCI: Setting up controller.. done.
[DEBUG] PCI: 00:14.0 init finished in 0 msecs
[DEBUG] PCI: 00:16.0 init
[DEBUG] ME: FW Partition Table : OK
[DEBUG] ME: Bringup Loader Failure : NO
[DEBUG] ME: Firmware Init Complete : NO
[DEBUG] ME: Manufacturing Mode : YES
[DEBUG] ME: Boot Options Present : NO
[DEBUG] ME: Update In Progress : NO
[DEBUG] ME: Current Working State : Initializing
[DEBUG] ME: Current Operation State : Bring up
[DEBUG] ME: Current Operation Mode : Debug or Disabled by AltDisableBit
[DEBUG] ME: Error Code : No Error
[DEBUG] ME: Progress Phase : BUP Phase
[DEBUG] ME: Power Management Event : Clean Moff->Mx wake
[DEBUG] ME: Progress Phase State : Check to see if straps say ME DISABLED
[CRIT ] intel_me_path: mbp is not ready!
[NOTE ] ME: BIOS path: Error
[DEBUG] ME: me_state=0, me_state_prev=0
[DEBUG] PCI: 00:16.0 init finished in 0 msecs
[DEBUG] PCI: 00:19.0 init
[DEBUG] PCI: 00:19.0 init finished in 0 msecs
[DEBUG] PCI: 00:1a.0 init
[DEBUG] EHCI: Setting up controller.. done.
[DEBUG] PCI: 00:1a.0 init finished in 0 msecs
[DEBUG] PCI: 00:1b.0 init
[DEBUG] Azalia: base = 0x83830000
[DEBUG] Azalia: codec_mask = 09
[DEBUG] azalia_audio: Initializing codec #3
[DEBUG] azalia_audio: codec viddid: 80862806
[DEBUG] azalia_audio: verb_size: 16
[DEBUG] azalia_audio: verb loaded.
[DEBUG] azalia_audio: Initializing codec #0
[DEBUG] azalia_audio: codec viddid: 10ec0269
[DEBUG] azalia_audio: verb_size: 72
[DEBUG] azalia_audio: verb loaded.
[DEBUG] PCI: 00:1b.0 init finished in 5 msecs
[DEBUG] PCI: 00:1c.0 init
[DEBUG] Initializing PCH PCIe bridge.
[DEBUG] PCI: 00:1c.0 init finished in 0 msecs
[DEBUG] PCI: 00:1c.1 init
[DEBUG] Initializing PCH PCIe bridge.
[DEBUG] PCI: 00:1c.1 init finished in 0 msecs
[DEBUG] PCI: 00:1c.2 init
[DEBUG] Initializing PCH PCIe bridge.
[DEBUG] PCI: 00:1c.2 init finished in 0 msecs
[DEBUG] PCI: 00:1d.0 init
[DEBUG] EHCI: Setting up controller.. done.
[DEBUG] PCI: 00:1d.0 init finished in 0 msecs
[DEBUG] PCI: 00:1f.0 init
[DEBUG] pch: lpc_init
[INFO ] PCH: detected QM77, device id: 0x1e55, rev id 0x4
[DEBUG] IOAPIC: Initializing IOAPIC at 0xfec00000
[DEBUG] IOAPIC: 24 interrupts
[DEBUG] IOAPIC: Clearing IOAPIC at 0xfec00000
[DEBUG] IOAPIC: Bootstrap Processor Local APIC = 0x00
[INFO ] Set power off after power failure.
[INFO ] NMI sources enabled.
[DEBUG] PantherPoint PM init
[DEBUG] RTC: failed = 0x0
[DEBUG] RTC Init
[DEBUG] apm_control: Disabling ACPI.
[DEBUG] APMC done.
[DEBUG] pch_spi_init
[DEBUG] PCI: 00:1f.0 init finished in 0 msecs
[DEBUG] PCI: 00:1f.2 init
[DEBUG] SATA: Initializing...
[DEBUG] SATA: Controller in AHCI mode.
[DEBUG] ABAR: 0x83835000
[DEBUG] PCI: 00:1f.2 init finished in 0 msecs
[DEBUG] PCI: 00:1f.3 init
[DEBUG] PCI: 00:1f.3 init finished in 0 msecs
[DEBUG] PCI: 01:00.0 init
[DEBUG] PCI: 01:00.0 init finished in 0 msecs
[DEBUG] PCI: 01:00.3 init
[DEBUG] PCI: 01:00.3 init finished in 0 msecs
[DEBUG] PCI: 02:00.0 init
[DEBUG] PCI: 02:00.0 init finished in 0 msecs
[DEBUG] PNP: 00ff.2 init
[DEBUG] PNP: 00ff.2 init finished in 0 msecs
[DEBUG] smbus: PCI: 00:1f.3[0]->I2C: 01:54 init
[DEBUG] I2C: 01:54 init finished in 0 msecs
[DEBUG] smbus: PCI: 00:1f.3[0]->I2C: 01:55 init
[DEBUG] I2C: 01:55 init finished in 0 msecs
[DEBUG] smbus: PCI: 00:1f.3[0]->I2C: 01:56 init
[DEBUG] I2C: 01:56 init finished in 0 msecs
[DEBUG] smbus: PCI: 00:1f.3[0]->I2C: 01:57 init
[DEBUG] I2C: 01:57 init finished in 0 msecs
[DEBUG] smbus: PCI: 00:1f.3[0]->I2C: 01:5c init
[DEBUG] Locking EEPROM RFID
[DEBUG] init EEPROM done
[DEBUG] I2C: 01:5c init finished in 22 msecs
[DEBUG] smbus: PCI: 00:1f.3[0]->I2C: 01:5d init
[DEBUG] I2C: 01:5d init finished in 0 msecs
[DEBUG] smbus: PCI: 00:1f.3[0]->I2C: 01:5e init
[DEBUG] I2C: 01:5e init finished in 0 msecs
[DEBUG] smbus: PCI: 00:1f.3[0]->I2C: 01:5f init
[DEBUG] I2C: 01:5f init finished in 0 msecs
[INFO ] Devices initialized
[DEBUG] BS: BS_DEV_INIT run times (exec / console): 584 / 1 ms
[INFO ] Found TPM ST33ZP24 by ST Microelectronics
[DEBUG] TPM: Startup
[DEBUG] TPM: command 0x99 returned 0x0
[DEBUG] TPM: Asserting physical presence
[DEBUG] TPM: command 0x4000000a returned 0x0
[DEBUG] TPM: command 0x65 returned 0x801
[DEBUG] TPM: Continue self test
[DEBUG] TPM: command 0x53 returned 0x0
[DEBUG] TPM: command 0x65 returned 0x0
[DEBUG] TPM: flags disable=0, deactivated=0, nvlocked=1
[INFO ] TPM: setup succeeded
[DEBUG] BS: BS_DEV_INIT exit times (exec / console): 137 / 0 ms
[INFO ] Finalize devices...
[DEBUG] PCI: 00:1f.0 final
[DEBUG] flash size 0xc00000 bytes
[INFO ] SF: Detected 00 0000 with sector size 0x1000, total 0xc00000
[DEBUG] apm_control: Finalizing SMM.
[DEBUG] APMC done.
[INFO ] Devices finalized
[INFO ] CBFS: Found 'fallback/dsdt.aml' @0x47280 size 0x38ba in mcache @0x7ffdd200
[WARN ] CBFS: 'fallback/slic' not found.
[INFO ] ACPI: Writing ACPI tables at 7ff3e000.
[DEBUG] ACPI: * FACS
[DEBUG] ACPI: * DSDT
[DEBUG] ACPI: * FADT
[DEBUG] ACPI: added table 1/32, length now 40
[DEBUG] ACPI: * SSDT
[DEBUG] Found 1 CPU(s) with 8 core(s) each.
[DEBUG] PSS: 2701MHz power 45000 control 0x2500 status 0x2500
[DEBUG] PSS: 2700MHz power 45000 control 0x1b00 status 0x1b00
[DEBUG] PSS: 2400MHz power 38601 control 0x1800 status 0x1800
[DEBUG] PSS: 2200MHz power 34542 control 0x1600 status 0x1600
[DEBUG] PSS: 2000MHz power 30669 control 0x1400 status 0x1400
[DEBUG] PSS: 1800MHz power 26973 control 0x1200 status 0x1200
[DEBUG] PSS: 1600MHz power 23389 control 0x1000 status 0x1000
[DEBUG] PSS: 1400MHz power 19976 control 0xe00 status 0xe00
[DEBUG] PSS: 1200MHz power 16703 control 0xc00 status 0xc00
[DEBUG] PSS: 2701MHz power 45000 control 0x2500 status 0x2500
[DEBUG] PSS: 2700MHz power 45000 control 0x1b00 status 0x1b00
[DEBUG] PSS: 2400MHz power 38601 control 0x1800 status 0x1800
[DEBUG] PSS: 2200MHz power 34542 control 0x1600 status 0x1600
[DEBUG] PSS: 2000MHz power 30669 control 0x1400 status 0x1400
[DEBUG] PSS: 1800MHz power 26973 control 0x1200 status 0x1200
[DEBUG] PSS: 1600MHz power 23389 control 0x1000 status 0x1000
[DEBUG] PSS: 1400MHz power 19976 control 0xe00 status 0xe00
[DEBUG] PSS: 1200MHz power 16703 control 0xc00 status 0xc00
[DEBUG] PSS: 2701MHz power 45000 control 0x2500 status 0x2500
[DEBUG] PSS: 2700MHz power 45000 control 0x1b00 status 0x1b00
[DEBUG] PSS: 2400MHz power 38601 control 0x1800 status 0x1800
[DEBUG] PSS: 2200MHz power 34542 control 0x1600 status 0x1600
[DEBUG] PSS: 2000MHz power 30669 control 0x1400 status 0x1400
[DEBUG] PSS: 1800MHz power 26973 control 0x1200 status 0x1200
[DEBUG] PSS: 1600MHz power 23389 control 0x1000 status 0x1000
[DEBUG] PSS: 1400MHz power 19976 control 0xe00 status 0xe00
[DEBUG] PSS: 1200MHz power 16703 control 0xc00 status 0xc00
[DEBUG] PSS: 2701MHz power 45000 control 0x2500 status 0x2500
[DEBUG] PSS: 2700MHz power 45000 control 0x1b00 status 0x1b00
[DEBUG] PSS: 2400MHz power 38601 control 0x1800 status 0x1800
[DEBUG] PSS: 2200MHz power 34542 control 0x1600 status 0x1600
[DEBUG] PSS: 2000MHz power 30669 control 0x1400 status 0x1400
[DEBUG] PSS: 1800MHz power 26973 control 0x1200 status 0x1200
[DEBUG] PSS: 1600MHz power 23389 control 0x1000 status 0x1000
[DEBUG] PSS: 1400MHz power 19976 control 0xe00 status 0xe00
[DEBUG] PSS: 1200MHz power 16703 control 0xc00 status 0xc00
[DEBUG] PSS: 2701MHz power 45000 control 0x2500 status 0x2500
[DEBUG] PSS: 2700MHz power 45000 control 0x1b00 status 0x1b00
[DEBUG] PSS: 2400MHz power 38601 control 0x1800 status 0x1800
[DEBUG] PSS: 2200MHz power 34542 control 0x1600 status 0x1600
[DEBUG] PSS: 2000MHz power 30669 control 0x1400 status 0x1400
[DEBUG] PSS: 1800MHz power 26973 control 0x1200 status 0x1200
[DEBUG] PSS: 1600MHz power 23389 control 0x1000 status 0x1000
[DEBUG] PSS: 1400MHz power 19976 control 0xe00 status 0xe00
[DEBUG] PSS: 1200MHz power 16703 control 0xc00 status 0xc00
[DEBUG] PSS: 2701MHz power 45000 control 0x2500 status 0x2500
[DEBUG] PSS: 2700MHz power 45000 control 0x1b00 status 0x1b00
[DEBUG] PSS: 2400MHz power 38601 control 0x1800 status 0x1800
[DEBUG] PSS: 2200MHz power 34542 control 0x1600 status 0x1600
[DEBUG] PSS: 2000MHz power 30669 control 0x1400 status 0x1400
[DEBUG] PSS: 1800MHz power 26973 control 0x1200 status 0x1200
[DEBUG] PSS: 1600MHz power 23389 control 0x1000 status 0x1000
[DEBUG] PSS: 1400MHz power 19976 control 0xe00 status 0xe00
[DEBUG] PSS: 1200MHz power 16703 control 0xc00 status 0xc00
[DEBUG] PSS: 2701MHz power 45000 control 0x2500 status 0x2500
[DEBUG] PSS: 2700MHz power 45000 control 0x1b00 status 0x1b00
[DEBUG] PSS: 2400MHz power 38601 control 0x1800 status 0x1800
[DEBUG] PSS: 2200MHz power 34542 control 0x1600 status 0x1600
[DEBUG] PSS: 2000MHz power 30669 control 0x1400 status 0x1400
[DEBUG] PSS: 1800MHz power 26973 control 0x1200 status 0x1200
[DEBUG] PSS: 1600MHz power 23389 control 0x1000 status 0x1000
[DEBUG] PSS: 1400MHz power 19976 control 0xe00 status 0xe00
[DEBUG] PSS: 1200MHz power 16703 control 0xc00 status 0xc00
[DEBUG] PSS: 2701MHz power 45000 control 0x2500 status 0x2500
[DEBUG] PSS: 2700MHz power 45000 control 0x1b00 status 0x1b00
[DEBUG] PSS: 2400MHz power 38601 control 0x1800 status 0x1800
[DEBUG] PSS: 2200MHz power 34542 control 0x1600 status 0x1600
[DEBUG] PSS: 2000MHz power 30669 control 0x1400 status 0x1400
[DEBUG] PSS: 1800MHz power 26973 control 0x1200 status 0x1200
[DEBUG] PSS: 1600MHz power 23389 control 0x1000 status 0x1000
[DEBUG] PSS: 1400MHz power 19976 control 0xe00 status 0xe00
[DEBUG] PSS: 1200MHz power 16703 control 0xc00 status 0xc00
[DEBUG] PCI space above 4GB MMIO is at 0x17d600000, len = 0xe82a00000
[DEBUG] Generating ACPI PIRQ entries
[INFO ] \_SB_.PCI0.TPM: LPC TPM PNP: 0c31.0
[INFO ] ACPI: * H8
[INFO ] H8: BDC not installed
[INFO ] H8: WWAN detection not implemented. Assuming WWAN installed
[DEBUG] ACPI: added table 2/32, length now 44
[DEBUG] ACPI: * MCFG
[DEBUG] ACPI: added table 3/32, length now 48
[DEBUG] ACPI: * TCPA
[DEBUG] TCPA log created at 0x7ff2e000
[DEBUG] ACPI: added table 4/32, length now 52
[DEBUG] ACPI: * MADT
[DEBUG] IOAPIC: 24 interrupts
[DEBUG] ACPI: added table 5/32, length now 56
[DEBUG] current = 7ff44900
[DEBUG] ACPI: * DMAR
[DEBUG] ACPI: added table 6/32, length now 60
[DEBUG] current = 7ff449c0
[DEBUG] ACPI: * HPET
[DEBUG] ACPI: added table 7/32, length now 64
[INFO ] ACPI: done.
[DEBUG] ACPI tables: 27136 bytes.
[DEBUG] smbios_write_tables: 7ff26000
[INFO ] Create SMBIOS type 16
[INFO ] Create SMBIOS type 17
[INFO ] Create SMBIOS type 20
[DEBUG] SMBIOS tables: 950 bytes.
[DEBUG] Writing table forward entry at 0x00000500
[DEBUG] Wrote coreboot table at: 0x00000500, 0x10 bytes, checksum 5fe8
[DEBUG] Writing coreboot table at 0x7ff62000
[INFO ] CBFS: Found 'cmos_layout.bin' @0x4acc0 size 0x83c in mcache @0x7ffdd254
[DEBUG] 0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
[DEBUG] 1. 0000000000001000-000000000009ffff: RAM
[DEBUG] 2. 00000000000a0000-00000000000fffff: RESERVED
[DEBUG] 3. 0000000000100000-000000007ff25fff: RAM
[DEBUG] 4. 000000007ff26000-000000007ff7afff: CONFIGURATION TABLES
[DEBUG] 5. 000000007ff7b000-000000007ffcdfff: RAMSTAGE
[DEBUG] 6. 000000007ffce000-000000007fffffff: CONFIGURATION TABLES
[DEBUG] 7. 0000000080000000-00000000829fffff: RESERVED
[DEBUG] 8. 00000000f0000000-00000000f3ffffff: RESERVED
[DEBUG] 9. 00000000fed40000-00000000fed44fff: RESERVED
[DEBUG] 10. 00000000fed90000-00000000fed91fff: RESERVED
[DEBUG] 11. 0000000100000000-000000017d5fffff: RAM
[INFO ] Setting up bootsplash in 1024x768@32
[INFO ] CBFS: Found 'bootsplash.jpg' @0x43840 size 0x39f8 in mcache @0x7ffdd1d8
[DEBUG] Bootsplash image resolution: 1024x768
[INFO ] Bootsplash loaded
[DEBUG] Wrote coreboot table at: 0x7ff62000, 0xc10 bytes, checksum 5c63
[DEBUG] coreboot table: 3112 bytes.
[DEBUG] IMD ROOT 0. 0x7ffff000 0x00001000
[DEBUG] IMD SMALL 1. 0x7fffe000 0x00001000
[DEBUG] CONSOLE 2. 0x7ffde000 0x00020000
[DEBUG] RO MCACHE 3. 0x7ffdd000 0x00000404
[DEBUG] TIME STAMP 4. 0x7ffdc000 0x00000910
[DEBUG] MEM INFO 5. 0x7ffdb000 0x000007a8
[DEBUG] AFTER CAR 6. 0x7ffce000 0x0000d000
[DEBUG] RAMSTAGE 7. 0x7ff7a000 0x00054000
[DEBUG] SMM BACKUP 8. 0x7ff6a000 0x00010000
[DEBUG] COREBOOT 9. 0x7ff62000 0x00008000
[DEBUG] ACPI 10. 0x7ff3e000 0x00024000
[DEBUG] TCPA TCGLOG11. 0x7ff2e000 0x00010000
[DEBUG] SMBIOS 12. 0x7ff26000 0x00008000
[DEBUG] IMD small region:
[DEBUG] IMD ROOT 0. 0x7fffec00 0x00000400
[DEBUG] FMAP 1. 0x7fffeb20 0x000000e0
[DEBUG] ROMSTAGE 2. 0x7fffeb00 0x00000004
[DEBUG] ROMSTG STCK 3. 0x7fffea40 0x000000a8
[DEBUG] ACPI GNVS 4. 0x7fffe940 0x00000100
[DEBUG] BS: BS_WRITE_TABLES run times (exec / console): 43 / 0 ms
[INFO ] CBFS: Found 'fallback/payload' @0x67f80 size 0x11885 in mcache @0x7ffdd310
[DEBUG] Checking segment from ROM address 0xffc781ac
[DEBUG] Payload being loaded at below 1MiB without region being marked as RAM usable.
[DEBUG] Checking segment from ROM address 0xffc781c8
[DEBUG] Loading segment from ROM address 0xffc781ac
[DEBUG] code (compression=1)
[DEBUG] New segment dstaddr 0x000dedc0 memsize 0x21240 srcaddr 0xffc781e4 filesize 0x1184d
[DEBUG] Loading Segment: addr: 0x000dedc0 memsz: 0x0000000000021240 filesz: 0x000000000001184d
[DEBUG] using LZMA
[DEBUG] Loading segment from ROM address 0xffc781c8
[DEBUG] Entry Point 0x000fd25b
[DEBUG] BS: BS_PAYLOAD_LOAD run times (exec / console): 20 / 0 ms
[DEBUG] ICH-NM10-PCH: watchdog disabled
[DEBUG] Jumping to boot code at 0x000fd25b(0x7ff62000)
SeaBIOS (version rel-1.16.1-0-g3208b09)
BUILD: gcc: (coreboot toolchain v2021-09-23_b0d87f753c) 11.2.0 binutils: (GNU Binutils) 2.37
Found coreboot cbmem console @ 7ffde000
Found mainboard LENOVO ThinkPad W530
Relocating init from 0x000e0520 to 0x7ef18aa0 (size 54464)
Found CBFS header at 0xffc1022c
multiboot: eax=7ffb6948, ebx=7ffb68c4
Found 17 PCI devices (max PCI bus is 03)
Copying SMBIOS from 0x7ff26000 to 0x000f67c0
Copying SMBIOS 3.0 from 0x7ff26020 to 0x000f67a0
Copying ACPI RSDP from 0x7ff3e000 to 0x000f6770
table(50434146)=0x7ff41b50 (via xsdt)
Using pmtimer, ioport 0x508
table(41504354)=0x7ff44820 (via xsdt)
Scan for VGA option rom
Running option rom at c000:0003
pmm call arg1=0
Turning on vga text mode console
SeaBIOS (version rel-1.16.1-0-g3208b09)
Machine UUID b0ed3381-43e8-11cb-88c4-f673c4ea3c86
PCI: XHCI at 00:14.0 (mmio 0x83820000)
XHCI init: regs @ 0x83820000, 8 ports, 32 slots, 32 byte contexts
XHCI protocol USB 2.00, 4 ports (offset 1), def 3001
XHCI protocol USB 3.00, 4 ports (offset 5), def 1000
XHCI extcap 0xc1 @ 0x83828040
XHCI extcap 0xc0 @ 0x83828070
XHCI extcap 0x1 @ 0x83828330
EHCI init on dev 00:1a.0 (regs=0x83836020)
EHCI init on dev 00:1d.0 (regs=0x83837020)
AHCI controller at 00:1f.2, iobase 0x83835000, irq 11
Searching bootorder for: /pci@i0cf8/pci-bridge@1c/*@0
Searching bootorder for: HALT
Found 0 lpt ports
Found 0 serial ports
Searching bootorder for: /rom@img/nvramcui
Searching bootorder for: /rom@img/coreinfo
Searching bootorder for: /pci@i0cf8/*@1f,2/drive@2/disk@0
AHCI/2: Set transfer mode to UDMA-6
Searching bios-geometry for: /pci@i0cf8/*@1f,2/drive@2/disk@0
AHCI/2: registering: "AHCI/2: Dogfish SSD 1TB ATA-10 Hard-Disk (931 GiBytes)"
XHCI no devices found
Initialized USB HUB (0 ports used)
Discarding ps2 data aa (status=11)
Discarding ps2 data e0 (status=11)
Discarding ps2 data 0f (status=11)
Discarding ps2 data e0 (status=11)
Discarding ps2 data f0 (status=11)
Discarding ps2 data 0f (status=11)
WARNING - Timeout at ps2_recvbyte:182!
PS2 keyboard initialized
WARNING - Timeout at ehci_wait_td:517!
ehci pipe=0x7ef14400 cur=7ef0ddc0 tok=80080d80 next=7ef0de00 td=0x7ef0ddc0 status=80080d80
Initialized USB HUB (0 ports used)
All threads complete.
Scan for option roms
Press ESC for boot menu.
Turning on vga text mode console
SeaBIOS (version rel-1.16.1-0-g3208b09)
Machine UUID b0ed3381-43e8-11cb-88c4-f673c4ea3c86
Searching bootorder for: HALT
drive 0x000f6700: PCHS=16383/16/63 translation=lba LCHS=1024/255/63 s=1953525168
Space available for UMB: c7000-ec000, f5fe0-f6700
Returned 16703488 bytes of ZoneHigh
e820 map has 9 items:
0: 0000000000000000 - 000000000009fc00 = 1 RAM
1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED
2: 00000000000f0000 - 0000000000100000 = 2 RESERVED
3: 0000000000100000 - 000000007ff14000 = 1 RAM
4: 000000007ff14000 - 0000000082a00000 = 2 RESERVED
5: 00000000f0000000 - 00000000f4000000 = 2 RESERVED
6: 00000000fed40000 - 00000000fed45000 = 2 RESERVED
7: 00000000fed90000 - 00000000fed92000 = 2 RESERVED
8: 0000000100000000 - 000000017d600000 = 1 RAM
enter handle_19:
NULL
Booting from Hard Disk...
Booting from 0000:7c00