blob: 65312173ac5a908b3d274ea2c90260fdc43d10c0 [file] [log] [blame]
[NOTE ] coreboot-4.19-97-g8190840fdf Sun Jan 22 19:08:55 UTC 2023 bootblock starting (log level: 7)...
[INFO ] Timestamp - end of bootblock: 10382047
[INFO ] Timestamp - starting to load romstage: 10398494
[DEBUG] FMAP: Found "FLASH" version 1.1 at 0x0.
[DEBUG] FMAP: base = 0xffc00000 size = 0x400000 #areas = 3
[DEBUG] FMAP: area COREBOOT found @ 200 (4193792 bytes)
[INFO ] CBFS: mcache @0x00014e00 built for 14 files, used 0x314 of 0x4000 bytes
[INFO ] CBFS: Found 'fallback/romstage' @0x80 size 0x72c0 in mcache @0x00014e2c
[INFO ] Timestamp - finished loading romstage: 10488953
[DEBUG] BS: bootblock times (exec / console): total (unknown) / 0 ms
[NOTE ] coreboot-4.19-97-g8190840fdf Sun Jan 22 19:08:55 UTC 2023 romstage starting (log level: 7)...
[DEBUG] SMBus controller enabled
[INFO ] QEMU: firmware config interface detected
[INFO ] Firmware config version id: 3
[INFO ] QEMU: firmware config: Found 'etc/e820'
[DEBUG] CBMEM:
[DEBUG] IMD: root @ 0x3ffff000 254 entries.
[DEBUG] IMD: root @ 0x3fffec00 62 entries.
[DEBUG] FMAP: area COREBOOT found @ 200 (4193792 bytes)
[INFO ] CBFS: Found 'fallback/postcar' @0x1ff80 size 0x8b00 in mcache @0x0001500c
[DEBUG] Loading module at 0x3ffce000 with entry 0x3ffce042. filesize: 0x7800 memsize: 0xdb58
[DEBUG] Processing 600 relocs. Offset value of 0x3dfce000
[INFO ] Timestamp - end of romstage: 20829970
[DEBUG] BS: romstage times (exec / console): total (unknown) / 0 ms
[NOTE ] coreboot-4.19-97-g8190840fdf Sun Jan 22 19:08:55 UTC 2023 postcar starting (log level: 7)...
[INFO ] Timestamp - start of postcar: 26188485
[INFO ] Timestamp - end of postcar: 26198816
[INFO ] Timestamp - starting to load ramstage: 26207211
[DEBUG] FMAP: area COREBOOT found @ 200 (4193792 bytes)
[INFO ] CBFS: Found 'fallback/ramstage' @0xd040 size 0x10f95 in mcache @0x3ffdd140
[INFO ] Timestamp - starting LZMA decompress (ignore for x86): 26232347
[INFO ] Timestamp - finished LZMA decompress (ignore for x86): 44738450
[DEBUG] Loading module at 0x3ff92000 with entry 0x3ff92000. filesize: 0x28db8 memsize: 0x3a0f8
[DEBUG] Processing 3993 relocs. Offset value of 0x3bf92000
[INFO ] Timestamp - finished loading ramstage: 44929736
[DEBUG] BS: postcar times (exec / console): total (unknown) / 0 ms
[NOTE ] coreboot-4.19-97-g8190840fdf Sun Jan 22 19:08:55 UTC 2023 ramstage starting (log level: 7)...
[INFO ] Timestamp - start of ramstage: 61992640
[INFO ] Timestamp - device enumeration: 62010823
[DEBUG] Initializing i82801ix southbridge...
[INFO ] Enumerating buses...
[DEBUG] Root Device scanning...
[DEBUG] CPU_CLUSTER: 0 enabled
[DEBUG] DOMAIN: 0000 enabled
[DEBUG] DOMAIN: 0000 scanning...
[DEBUG] PCI: pci_scan_bus for bus 00
[DEBUG] PCI: 00:00.0 [8086/29c0] enabled
[DEBUG] PCI: 00:01.0 [1234/1111] enabled
[DEBUG] PCI: 00:02.0 [8086/10d3] enabled
[INFO ] PCI: Static device PCI: 00:1a.0 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1a.1 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1a.2 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1a.7 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1b.0 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1c.0 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1c.1 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1c.2 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1c.3 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1c.4 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1c.5 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1d.0 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1d.1 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1d.2 not found, disabling it.
[INFO ] PCI: Static device PCI: 00:1d.7 not found, disabling it.
[DEBUG] PCI: 00:1f.0 [8086/2918] enabled
[DEBUG] PCI: 00:1f.2 [8086/2922] enabled
[DEBUG] PCI: 00:1f.3 [8086/2930] enabled
[WARN ] PCI: Leftover static devices:
[WARN ] PCI: 00:19.0
[WARN ] PCI: 00:1a.0
[WARN ] PCI: 00:1a.1
[WARN ] PCI: 00:1a.2
[WARN ] PCI: 00:1a.7
[WARN ] PCI: 00:1b.0
[WARN ] PCI: 00:1c.0
[WARN ] PCI: 00:1c.1
[WARN ] PCI: 00:1c.2
[WARN ] PCI: 00:1c.3
[WARN ] PCI: 00:1c.4
[WARN ] PCI: 00:1c.5
[WARN ] PCI: 00:1d.0
[WARN ] PCI: 00:1d.1
[WARN ] PCI: 00:1d.2
[WARN ] PCI: 00:1d.7
[WARN ] PCI: 00:1f.5
[WARN ] PCI: 00:1f.6
[WARN ] PCI: Check your devicetree.cb.
[DEBUG] PCI: 00:1f.0 scanning...
[DEBUG] PNP: 0c31.0 enabled
[DEBUG] scan_bus: bus PCI: 00:1f.0 finished in 0 msecs
[DEBUG] PCI: 00:1f.3 scanning...
[DEBUG] scan_bus: bus PCI: 00:1f.3 finished in 0 msecs
[DEBUG] scan_bus: bus DOMAIN: 0000 finished in 0 msecs
[DEBUG] scan_bus: bus Root Device finished in 0 msecs
[INFO ] done
[INFO ] Timestamp - device configuration: 66427905
[DEBUG] found VGA at PCI: 00:01.0
[DEBUG] Setting up VGA for PCI: 00:01.0
[DEBUG] Setting PCI_BRIDGE_CTL_VGA for bridge DOMAIN: 0000
[DEBUG] Setting PCI_BRIDGE_CTL_VGA for bridge Root Device
[INFO ] Allocating resources...
[INFO ] Reading resources...
[INFO ] QEMU: firmware config interface detected
[INFO ] Firmware config version id: 3
[INFO ] QEMU: firmware config: Found 'etc/e820'
[DEBUG] QEMU: e820/res: 0xfeffc000 +0x00004000
[DEBUG] QEMU: e820/ram: 0x00000000 + 0x40000000
[DEBUG] QEMU: reserve ioports 0x0510-0x0511 [firmware-config]
[DEBUG] QEMU: reserve ioports 0x5658-0x5658 [vmware-port]
[DEBUG] Adding PCIe enhanced config space BAR 0xb0000000-0xc0000000.
[ERROR] PNP: 0c31.0 missing read_resources
[INFO ] Done reading resources.
[INFO ] === Resource allocator: DOMAIN: 0000 - Pass 1 (gathering requirements) ===
[INFO ] === Resource allocator: DOMAIN: 0000 - Pass 2 (allocating resources) ===
[DEBUG] DOMAIN: 0000 io: base: 0 size: 0 align: 0 gran: 0 limit: ffff
[DEBUG] update_constraints: DOMAIN: 0000 0d base 00000510 limit 00000511 io (fixed)
[DEBUG] update_constraints: DOMAIN: 0000 0e base 00005658 limit 00005658 io (fixed)
[DEBUG] update_constraints: PCI: 00:1f.0 10000000 base 00000000 limit 00000fff io (fixed)
[DEBUG] update_constraints: PCI: 00:1f.3 20 base 00000400 limit 0000041f io (fixed)
[INFO ] DOMAIN: 0000: Resource ranges:
[INFO ] * Base: 1000, Size: 4658, Tag: 100
[INFO ] * Base: 5659, Size: a9a7, Tag: 100
[DEBUG] PCI: 00:02.0 18 * [0x1000 - 0x101f] limit: 101f io
[DEBUG] PCI: 00:1f.2 20 * [0x1020 - 0x103f] limit: 103f io
[DEBUG] DOMAIN: 0000 io: base: 0 size: 0 align: 0 gran: 0 limit: ffff done
[DEBUG] DOMAIN: 0000 mem: base: 0 size: 0 align: 0 gran: 0 limit: ffffffffff
[DEBUG] update_constraints: DOMAIN: 0000 0a base feffc000 limit feffffff mem (fixed)
[DEBUG] update_constraints: DOMAIN: 0000 0b base 00000000 limit 0009ffff mem (fixed)
[DEBUG] update_constraints: DOMAIN: 0000 0c base 000c0000 limit 3fffffff mem (fixed)
[DEBUG] update_constraints: DOMAIN: 0000 0f base 000a0000 limit 000bffff mem (fixed)
[DEBUG] update_constraints: DOMAIN: 0000 10 base 000c0000 limit 000fffff mem (fixed)
[DEBUG] update_constraints: DOMAIN: 0000 11 base 40000000 limit afffffff mem (fixed)
[DEBUG] update_constraints: DOMAIN: 0000 03 base fee00000 limit fee0ffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 02 base b0000000 limit bfffffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:00.0 00 base 00008000 limit 0000dfff mem (fixed)
[DEBUG] update_constraints: PCI: 00:1f.0 10000100 base ff800000 limit ffffffff mem (fixed)
[DEBUG] update_constraints: PCI: 00:1f.0 03 base fec00000 limit fec00fff mem (fixed)
[INFO ] DOMAIN: 0000: Resource ranges:
[INFO ] * Base: c0000000, Size: 3ec00000, Tag: 200
[INFO ] * Base: fec01000, Size: 1ff000, Tag: 200
[INFO ] * Base: fee10000, Size: 1ec000, Tag: 200
[INFO ] * Base: ff000000, Size: 800000, Tag: 200
[INFO ] * Base: 100000000, Size: ff00000000, Tag: 100200
[DEBUG] PCI: 00:01.0 10 * [0xc0000000 - 0xc0ffffff] limit: c0ffffff prefmem
[DEBUG] PCI: 00:02.0 30 * [0xc1000000 - 0xc103ffff] limit: c103ffff mem
[DEBUG] PCI: 00:02.0 10 * [0xc1040000 - 0xc105ffff] limit: c105ffff mem
[DEBUG] PCI: 00:02.0 14 * [0xc1060000 - 0xc107ffff] limit: c107ffff mem
[DEBUG] PCI: 00:01.0 30 * [0xc1080000 - 0xc108ffff] limit: c108ffff mem
[DEBUG] PCI: 00:02.0 1c * [0xc1090000 - 0xc1093fff] limit: c1093fff mem
[DEBUG] PCI: 00:01.0 18 * [0xc1094000 - 0xc1094fff] limit: c1094fff mem
[DEBUG] PCI: 00:1f.2 24 * [0xc1095000 - 0xc1095fff] limit: c1095fff mem
[DEBUG] DOMAIN: 0000 mem: base: 0 size: 0 align: 0 gran: 0 limit: ffffffffff done
[INFO ] === Resource allocator: DOMAIN: 0000 - resource allocation complete ===
[DEBUG] PCI: 00:01.0 10 <- [0x00000000c0000000 - 0x00000000c0ffffff] size 0x01000000 gran 0x18 prefmem
[DEBUG] PCI: 00:01.0 18 <- [0x00000000c1094000 - 0x00000000c1094fff] size 0x00001000 gran 0x0c mem
[DEBUG] PCI: 00:01.0 30 <- [0x00000000c1080000 - 0x00000000c108ffff] size 0x00010000 gran 0x10 romem
[DEBUG] PCI: 00:02.0 10 <- [0x00000000c1040000 - 0x00000000c105ffff] size 0x00020000 gran 0x11 mem
[DEBUG] PCI: 00:02.0 14 <- [0x00000000c1060000 - 0x00000000c107ffff] size 0x00020000 gran 0x11 mem
[DEBUG] PCI: 00:02.0 18 <- [0x0000000000001000 - 0x000000000000101f] size 0x00000020 gran 0x05 io
[DEBUG] PCI: 00:02.0 1c <- [0x00000000c1090000 - 0x00000000c1093fff] size 0x00004000 gran 0x0e mem
[DEBUG] PCI: 00:02.0 30 <- [0x00000000c1000000 - 0x00000000c103ffff] size 0x00040000 gran 0x12 romem
[DEBUG] PCI: 00:1f.2 20 <- [0x0000000000001020 - 0x000000000000103f] size 0x00000020 gran 0x05 io
[DEBUG] PCI: 00:1f.2 24 <- [0x00000000c1095000 - 0x00000000c1095fff] size 0x00001000 gran 0x0c mem
[INFO ] Done setting resources.
[INFO ] Done allocating resources.
[DEBUG] BS: BS_DEV_RESOURCES run times (exec / console): 1 / 0 ms
[INFO ] Timestamp - device enable: 76333005
[INFO ] Enabling resources...
[DEBUG] PCI: 00:00.0 cmd <- 00
[DEBUG] PCI: 00:01.0 cmd <- 03
[DEBUG] PCI: 00:02.0 cmd <- 03
[DEBUG] PCI: 00:1f.0 subsystem <- 8086/2918
[DEBUG] PCI: 00:1f.0 cmd <- 100
[DEBUG] PCI: 00:1f.2 subsystem <- 8086/2922
[DEBUG] PCI: 00:1f.2 cmd <- 103
[DEBUG] PCI: 00:1f.3 subsystem <- 8086/2930
[DEBUG] PCI: 00:1f.3 cmd <- 101
[INFO ] done.
[DEBUG] BS: BS_DEV_INIT entry times (exec / console): 1 / 0 ms
[INFO ] Timestamp - device initialization: 87935762
[INFO ] Initializing devices...
[DEBUG] CPU_CLUSTER: 0 init
[DEBUG] Setting up SMI for CPU
[DEBUG] Save state size: 0x200 bytes
[INFO ] Will perform SMM setup.
[INFO ] CPU: QEMU Virtual CPU version 2.5+.
[INFO ] LAPIC 0x0 in XAPIC mode.
[DEBUG] CPU: APIC: 00 enabled
[DEBUG] CPU: APIC: 01 enabled
[DEBUG] Loading module at 0x00030000 with entry 0x00030000. filesize: 0x1b8 memsize: 0x1b8
[DEBUG] Processing 17 relocs. Offset value of 0x00030000
[DEBUG] Attempting to start 1 APs
[DEBUG] Waiting for 10ms after sending INIT.
[DEBUG] Waiting for SIPI to complete...
[DEBUG] done.
[DEBUG] Waiting for SIPI to complete...
[INFO ] LAPIC 0x1 in XAPIC mode.
[DEBUG] done.
[INFO ] AP: slot 1 apic_id 1
[DEBUG] Loading module at 0x00038000 with entry 0x00038000. filesize: 0x260 memsize: 0x260
[DEBUG] Processing 12 relocs. Offset value of 0x00038000
[DEBUG] smm_module_setup_stub: stack_top = 0xa1000
[DEBUG] smm_module_setup_stub: per cpu stack_size = 0x800
[DEBUG] smm_module_setup_stub: runtime.start32_offset = 0x4c
[DEBUG] smm_module_setup_stub: runtime.smm_size = 0x10000
[DEBUG] SMM Module: stub loaded at 38000. Will call 0x3ffa32ba
[DEBUG] Installing permanent SMM handler to 0x000a0000
[DEBUG] FX_SAVE [0xafc00-0xb0000]
[DEBUG] HANDLER [0xaf000-0xaf898]
[DEBUG] CPU 0
[DEBUG] ss0 [0xaee00-0xaf000]
[DEBUG] stub0 [0xa7000-0xa7260]
[DEBUG] CPU 1
[DEBUG] ss1 [0xaeba0-0xaeda0]
[DEBUG] stub1 [0xa6da0-0xa7000]
[DEBUG] stacks [0xa0000-0xa1000]
[DEBUG] Loading module at 0x000af000 with entry 0x000af084. filesize: 0x888 memsize: 0x898
[DEBUG] Processing 81 relocs. Offset value of 0x000af000
[DEBUG] Loading module at 0x000a7000 with entry 0x000a7000. filesize: 0x260 memsize: 0x260
[DEBUG] Processing 12 relocs. Offset value of 0x000a7000
[DEBUG] smm_module_setup_stub: stack_top = 0xa1000
[DEBUG] smm_module_setup_stub: per cpu stack_size = 0x800
[DEBUG] smm_module_setup_stub: runtime.start32_offset = 0x4c
[DEBUG] smm_module_setup_stub: runtime.smm_size = 0x10000
[DEBUG] SMM Module: placing smm entry code at a6da0, cpu # 0x1
[DEBUG] SMM Module: stub loaded at a7000. Will call 0x000af084
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x9f000, cpu = 0
[DEBUG] In relocation handler: cpu 0
[DEBUG] SMM revision: 0x00020064
[DEBUG] New SMBASE=0x0009f000
[DEBUG] Relocation complete.
[INFO ] smm_do_relocation : curr_smbase 0x30000 perm_smbase 0x9eda0, cpu = 1
[DEBUG] In relocation handler: cpu 1
[DEBUG] SMM revision: 0x00020064
[DEBUG] New SMBASE=0x0009eda0
[DEBUG] Relocation complete.
[INFO ] Initializing CPU #0
[DEBUG] CPU: vendor Intel device 60fb1
[DEBUG] CPU: family 0f, model 6b, stepping 01
[INFO ] CPU #0 initialized
[INFO ] Initializing CPU #1
[DEBUG] CPU: vendor Intel device 60fb1
[DEBUG] CPU: family 0f, model 6b, stepping 01
[INFO ] CPU #1 initialized
[INFO ] bsp_do_flight_plan done after 0 msecs.
[DEBUG] SMI_STS:
[DEBUG] GPE0_STS:
[DEBUG] ALT_GP_SMI_STS: GPI15 GPI14 GPI13 GPI12 GPI11 GPI10 GPI9 GPI8 GPI7 GPI6 GPI5 GPI4 GPI3 GPI2 GPI1 GPI0
[DEBUG] TCO_STS:
[DEBUG] Locking SMM.
[DEBUG] CPU_CLUSTER: 0 init finished in 11 msecs
[DEBUG] PCI: 00:00.0 init
[DEBUG] Assigning IRQ 11 to PCI: 00:02.0
[DEBUG] Assigning IRQ 10 to PCI: 00:1f.2
[DEBUG] Assigning IRQ 10 to PCI: 00:1f.3
[DEBUG] PCI: 00:00.0 init finished in 1 msecs
[DEBUG] PCI: 00:01.0 init
[DEBUG] PCI: 00:01.0 init finished in 11 msecs
[DEBUG] PCI: 00:02.0 init
[DEBUG] PCI: 00:02.0 init finished in 0 msecs
[DEBUG] PCI: 00:1f.0 init
[DEBUG] i82801ix: lpc_init
[DEBUG] IOAPIC: Initializing IOAPIC at 0xfec00000
[DEBUG] IOAPIC: 24 interrupts
[DEBUG] IOAPIC: Clearing IOAPIC at 0xfec00000
[DEBUG] IOAPIC: Bootstrap Processor Local APIC = 0x00
[INFO ] Set power on after power failure.
[INFO ] NMI sources disabled.
[DEBUG] rtc_failed = 0x0
[DEBUG] RTC Init
[DEBUG] apm_control: Disabling ACPI.
[DEBUG] APMC done.
[DEBUG] PCI: 00:1f.0 init finished in 0 msecs
[DEBUG] PCI: 00:1f.2 init
[DEBUG] i82801ix_sata: initializing...
[DEBUG] SATA controller in AHCI mode.
[DEBUG] ABAR: 0xc1095000
[DEBUG] PCI: 00:1f.2 init finished in 0 msecs
[DEBUG] PCI: 00:1f.3 init
[DEBUG] PCI: 00:1f.3 init finished in 0 msecs
[INFO ] Devices initialized
[DEBUG] BS: BS_DEV_INIT run times (exec / console): 24 / 0 ms
[INFO ] Finalize devices...
[INFO ] Devices finalized
[INFO ] Timestamp - device setup done: 291576763
[INFO ] Timestamp - cbmem post: 291595233
[INFO ] Timestamp - write tables: 291601916
[INFO ] QEMU: firmware config: Found 'etc/table-loader'
[DEBUG] QEMU: found ACPI tables in fw_cfg.
[INFO ] QEMU: firmware config: Found 'etc/acpi/rsdp'
[DEBUG] QEMU: loading "etc/acpi/rsdp" to 0x3ff51000 (len 20)
[INFO ] QEMU: firmware config: Found 'etc/acpi/tables'
[DEBUG] QEMU: loading "etc/acpi/tables" to 0x3ff51040 (len 131072)
[DEBUG] QEMU: loaded ACPI tables from fw_cfg.
[DEBUG] Looking on 0x3ff51000 for valid checksum
[DEBUG] Checksum 1 passed
[DEBUG] Checksum 2 passed all OK
[DEBUG] ACPI: * SSDT
[DEBUG] Generating ACPI PIRQ entries
[DEBUG] ACPI: added table 6/32, length now 60
[DEBUG] ACPI tables: 131136 bytes.
[DEBUG] smbios_write_tables: 3ff49000
[DEBUG] SMBIOS firmware version is set to coreboot_version: '4.19-97-g8190840fdf'
[DEBUG] SMBIOS: Unknown CPU or CPU doesn't support Deterministic Cache CPUID leaf
[INFO ] DOMAIN: 0000 (QEMU Northbridge q35)
[INFO ] QEMU: firmware config: Found 'etc/smbios/smbios-tables'
[DEBUG] QEMU: found smbios tables in fw_cfg (len 309).
[DEBUG] QEMU: coreboot type0 table found at 0x3ff49040.
[DEBUG] QEMU: loading smbios tables to 0x3ff49083
[DEBUG] SMBIOS tables: 468 bytes.
[DEBUG] Writing table forward entry at 0x00000500
[DEBUG] Wrote coreboot table at: 0x00000500, 0x10 bytes, checksum 2fe6
[DEBUG] Writing coreboot table at 0x3ff89000
[DEBUG] 0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
[DEBUG] 1. 0000000000001000-0000000000007fff: RAM
[DEBUG] 2. 0000000000008000-000000000000dfff: RESERVED
[DEBUG] 3. 000000000000e000-000000000009ffff: RAM
[DEBUG] 4. 00000000000a0000-00000000000fffff: RESERVED
[DEBUG] 5. 0000000000100000-000000003ff48fff: RAM
[DEBUG] 6. 000000003ff49000-000000003ff91fff: CONFIGURATION TABLES
[DEBUG] 7. 000000003ff92000-000000003ffccfff: RAMSTAGE
[DEBUG] 8. 000000003ffcd000-000000003fffffff: CONFIGURATION TABLES
[DEBUG] 9. 00000000b0000000-00000000bfffffff: RESERVED
[DEBUG] FMAP: area COREBOOT found @ 200 (4193792 bytes)
[DEBUG] Wrote coreboot table at: 0x3ff89000, 0x2e0 bytes, checksum d707
[DEBUG] coreboot table: 760 bytes.
[DEBUG] IMD ROOT 0. 0x3ffff000 0x00001000
[DEBUG] IMD SMALL 1. 0x3fffe000 0x00001000
[DEBUG] CONSOLE 2. 0x3ffde000 0x00020000
[DEBUG] RO MCACHE 3. 0x3ffdd000 0x00000314
[DEBUG] TIME STAMP 4. 0x3ffdc000 0x00000910
[DEBUG] AFTER CAR 5. 0x3ffcd000 0x0000f000
[DEBUG] RAMSTAGE 6. 0x3ff91000 0x0003c000
[DEBUG] COREBOOT 7. 0x3ff89000 0x00008000
[DEBUG] ACPI 8. 0x3ff51000 0x00038000
[DEBUG] SMBIOS 9. 0x3ff49000 0x00008000
[DEBUG] IMD small region:
[DEBUG] IMD ROOT 0. 0x3fffec00 0x00000400
[DEBUG] FMAP 1. 0x3fffeb40 0x000000b6
[DEBUG] ROMSTG STCK 2. 0x3fffeaa0 0x00000088
[DEBUG] ACPI GNVS 3. 0x3fffe9a0 0x00000100
[INFO ] Timestamp - finalize chips: 299469822
[DEBUG] BS: BS_WRITE_TABLES run times (exec / console): 1 / 0 ms
[INFO ] Timestamp - starting to load payload: 299500234
[INFO ] CBFS: Found 'fallback/payload' @0x28b00 size 0xfede in mcache @0x3ffdd250
[DEBUG] Checking segment from ROM address 0xffc28d2c
[DEBUG] Checking segment from ROM address 0xffc28d48
[DEBUG] Loading segment from ROM address 0xffc28d2c
[DEBUG] code (compression=1)
[DEBUG] New segment dstaddr 0x00100000 memsize 0x1354d0 srcaddr 0xffc28d64 filesize 0xfea6
[DEBUG] Loading Segment: addr: 0x00100000 memsz: 0x00000000001354d0 filesz: 0x000000000000fea6
[DEBUG] using LZMA
[INFO ] Timestamp - starting LZMA decompress (ignore for x86): 299597344
[INFO ] Timestamp - finished LZMA decompress (ignore for x86): 312634498
[DEBUG] Clearing Segment: addr: 0x000000000011e628 memsz: 0x0000000000116ea8
[DEBUG] Loading segment from ROM address 0xffc28d48
[DEBUG] Entry Point 0x00100000
[DEBUG] BS: BS_PAYLOAD_LOAD run times (exec / console): 2 / 0 ms
[DEBUG] ICH-NM10-PCH: watchdog disabled
[DEBUG] Jumping to boot code at 0x00100000(0x3ff89000)
[INFO ] Timestamp - selfboot jump: 315304529
coreboot: 4.19-97-g8190840fdf
FILO version 0.6.0 (pmenzel@ersatz) Sun Jan 22 23:05:32 UTC 2023
ahci: Found SATA controller 00:1f.02 (8086:2922).
ahci: ATA drive on port #1.
ata: Identified QEMU HARDDISK [2.5+]
ata: Support for LBA-48 enabled.
ahci: ATAPI drive on port #3.
atapi: Identified QEMU DVD-ROM [2.5+]
Press <Enter> for default boot, or <Esc> for boot prompt... 2? ?1? ?timed out
boot: hda1:/vmlinuz initrd=hda1:/initrd.img root=/dev/sda1 ro console=ttyS0,115200n8
Found Linux version 5.6.0-1-686-pae (debian-kernel@lists.debian.org) #1 SMP Debian 5.6.7-1 (2020-04-29) relocatable bzImage.
Loading kernel... ok
Loading initrd... ok
Jumping to entry point...