[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt9-2 (2015-04-13)
[    0.000000] Command line: root=/dev/nfs initrd=initrd-cb-test-tgt-i386 rootfstype=nfs nfsroot=10.100.1.100:/nfsroots/cb-test-tgt-01,v3,hard,nointr,tcp ip=10.100.1.10::10.100.1.1:255.255.255.0:embed-o-matic:eth0:off console=ttyS0,115200n8 consoleblank=0 rw BOOT_IMAGE=vmlinuz-cb-test-tgt-i386 
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bff99fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bff9a000-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: ASUS KFSN4-DRE/KFSN4-DRE, BIOS RAPTOR-NORMAL 03/21/2017
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] AGP: No AGP bridge found
[    0.000000] e820: last_pfn = 0x180000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-back
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000F8000000 mask FFFFFC000000 write-combining
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000180000000 aka 6144M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0xbff9a max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f0690-0x000f069f] mapped at [ffff8800000f0690]
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01af4000, 0x01af4fff] PGTABLE
[    0.000000] BRK [0x01af5000, 0x01af5fff] PGTABLE
[    0.000000] BRK [0x01af6000, 0x01af6fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x17fe00000-0x17fffffff]
[    0.000000]  [mem 0x17fe00000-0x17fffffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x17c000000-0x17fdfffff]
[    0.000000]  [mem 0x17c000000-0x17fdfffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x100000000-0x17bffffff]
[    0.000000]  [mem 0x100000000-0x17bffffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x00100000-0xbff99fff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x3fffffff] page 2M
[    0.000000]  [mem 0x40000000-0x7fffffff] page 1G
[    0.000000]  [mem 0x80000000-0xbfdfffff] page 2M
[    0.000000]  [mem 0xbfe00000-0xbff99fff] page 4k
[    0.000000] RAMDISK: [mem 0x7f24c000-0x7fffefff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F07F0 000024 (v02 CORE  )
[    0.000000] ACPI: XSDT 0x00000000BFFAB0E0 00006C (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: FACP 0x00000000BFFAD910 000074 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: DSDT 0x00000000BFFAB280 002687 (v02 ASUS   COREBOOT 00000001 INTL 20160831)
[    0.000000] ACPI: FACS 0x00000000BFFAB240 000040
[    0.000000] ACPI: SSDT 0x00000000BFFADA10 000E1E (v02 CORE   COREBOOT 0000002A CORE 0000002A)
[    0.000000] ACPI: TCPA 0x00000000BFFAE830 000032 (v02 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: APIC 0x00000000BFFAE870 000072 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SRAT 0x00000000BFFAE8F0 0000F0 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SLIT 0x00000000BFFAE9E0 000030 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: HPET 0x00000000BFFAEA10 000038 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SRAT 0x00000000BFFAEA50 0000F0 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SLIT 0x00000000BFFAEB40 000030 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] SRAT: PXM 0 -> APIC 0x00 -> Node 0
[    0.000000] SRAT: PXM 1 -> APIC 0x04 -> Node 1
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x00000000-0x0009ffff]
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x00100000-0xbfffffff]
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x100000000-0x13fffffff]
[    0.000000] SRAT: Node 1 PXM 1 [mem 0x140000000-0x17fffffff]
[    0.000000] NUMA: Initialized distance table, cnt=2
[    0.000000] NUMA: Node 0 [mem 0x00000000-0x0009ffff] + [mem 0x00100000-0xbfffffff] -> [mem 0x00000000-0xbfffffff]
[    0.000000] NUMA: Node 0 [mem 0x00000000-0xbfffffff] + [mem 0x100000000-0x13fffffff] -> [mem 0x00000000-0x13fffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x13fffffff]
[    0.000000]   NODE_DATA [mem 0x13fffb000-0x13fffffff]
[    0.000000] Initmem setup node 1 [mem 0x140000000-0x17fffffff]
[    0.000000]   NODE_DATA [mem 0x17fff8000-0x17fffcfff]
[    0.000000]  [ffffea0000000000-ffffea00045fffff] PMD -> [ffff88013be00000-ffff88013f5fffff] on node 0
[    0.000000]  [ffffea0004600000-ffffea00053fffff] PMD -> [ffff88017e600000-ffff88017f3fffff] on node 1
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x17fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0xbff99fff]
[    0.000000]   node   0: [mem 0x100000000-0x13fffffff]
[    0.000000]   node   1: [mem 0x140000000-0x17fffffff]
[    0.000000] On node 0 totalpages: 1048376
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10695 pages used for memmap
[    0.000000]   DMA32 zone: 782234 pages, LIFO batch:31
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 262144 pages, LIFO batch:31
[    0.000000] On node 1 totalpages: 262144
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 262144 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x2008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x18] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 24, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xbff9a000-0xcfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xffffffff]
[    0.000000] e820: [mem 0xd0000000-0xffffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:2
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88013fc00000 s80896 r8192 d21504 u2097152
[    0.000000] pcpu-alloc: s80896 r8192 d21504 u2097152 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 [1] 1 
[    0.000000] Built 2 zonelists in Node order, mobility grouping on.  Total pages: 1292580
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=/dev/nfs initrd=initrd-cb-test-tgt-i386 rootfstype=nfs nfsroot=10.100.1.100:/nfsroots/cb-test-tgt-01,v3,hard,nointr,tcp ip=10.100.1.10::10.100.1.1:255.255.255.0:embed-o-matic:eth0:off console=ttyS0,115200n8 consoleblank=0 rw BOOT_IMAGE=vmlinuz-cb-test-tgt-i386 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] AGP: Node 0: aperture [bus addr 0xf5ea000000-0xf5ebffffff] (32MB)
[    0.000000] Aperture beyond 4GB. Ignoring.
[    0.000000] AGP: Your BIOS doesn't leave a aperture memory hole
[    0.000000] AGP: Please enable the IOMMU option in the BIOS setup
[    0.000000] AGP: This costs you 64MB of RAM
[    0.000000] AGP: Mapping aperture over RAM [mem 0xb4000000-0xb7ffffff] (65536KB)
[    0.000000] PM: Registered nosave memory: [mem 0xb4000000-0xb7ffffff]
[    0.000000] Memory: 5012856K/5242080K available (5207K kernel code, 946K rwdata, 1832K rodata, 1204K init, 840K bss, 229224K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:33024 nr_irqs:512 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour *CGA 80x25
[    0.000000] console [ttyS0] enabled
[    0.000000] mempolicy: Disabling automatic NUMA balancing. Configure with numa_balancing= or the kernel.numa_balancing sysctl
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1909.763 MHz processor
[    0.000147] Calibrating delay loop (skipped), value calculated using timer frequency.. 3819.52 BogoMIPS (lpj=7639052)
[    0.010770] pid_max: default: 32768 minimum: 301
[    0.015406] ACPI: Core revision 20140424
[    0.021626] ACPI: All ACPI Tables successfully acquired
[    0.026950] Security Framework initialized
[    0.031062] AppArmor: AppArmor disabled by boot time parameter
[    0.036890] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.044328] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.057201] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.066905] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.073803] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.081615] Initializing cgroup subsys memory
[    0.085980] Initializing cgroup subsys devices
[    0.090435] Initializing cgroup subsys freezer
[    0.094879] Initializing cgroup subsys net_cls
[    0.099327] Initializing cgroup subsys blkio
[    0.103606] Initializing cgroup subsys perf_event
[    0.108315] Initializing cgroup subsys net_prio
[    0.112885] tseg: 0000000000
[    0.112895] CPU: Physical Processor ID: 0
[    0.116909] CPU: Processor Core ID: 0
[    0.120572] mce: CPU supports 6 MCE banks
[    0.124592] LVT offset 0 assigned for vector 0xf9
[    0.129303] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8
Last level dTLB entries: 4KB 512, 2MB 128, 4MB 64, 1GB 0
tlb_flushall_shift: 6
[    0.144634] Freeing SMP alternatives memory: 20K (ffffffff81a1b000 - ffffffff81a20000)
[    0.153632] ftrace: allocating 21614 entries in 85 pages
[    0.168791] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=0 pin2=0
[    0.214295] smpboot: CPU0: Quad-Core AMD Opteron(tm) Processor 8347 (fam: 10, model: 02, stepping: 01)
[    0.328537] Performance Events: AMD PMU driver.
[    0.333095] ... version:                0
[    0.337100] ... bit width:              48
[    0.341197] ... generic registers:      4
[    0.345201] ... value mask:             0000ffffffffffff
[    0.350511] ... max period:             00007fffffffffff
[    0.355812] ... fixed-purpose events:   0
[    0.359816] ... event mask:             000000000000000f
[    0.367324] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.375578] x86: Booting SMP configuration:
[    0.379761] .... node  #1, CPUs:      #1
[    0.492534] x86: Booted up 2 nodes, 2 CPUs
[    0.496817] smpboot: Total of 2 processors activated (7639.12 BogoMIPS)
[    0.505254] devtmpfs: initialized
[    0.516383] pinctrl core: initialized pinctrl subsystem
[    0.521757] NET: Registered protocol family 16
[    0.526411] cpuidle: using governor ladder
[    0.530511] cpuidle: using governor menu
[    0.534440] node 0 link 1: io port [1000, 3fff]
[    0.534443] TOM: 00000000c0000000 aka 3072M
[    0.538627] Fam 10h mmconf [mem 0xc0000000-0xcfffffff]
[    0.538631] node 0 link 1: mmio [fc000000, fc3fffff]
[    0.538635] node 0 link 1: mmio [f8000000, fbffffff]
[    0.538637] TOM2: 0000000180000000 aka 6144M
[    0.542908] bus: [bus 00-05] on node 0 link 1
[    0.542910] bus: 00 [io  0x0000-0xffff]
[    0.542912] bus: 00 [mem 0xd0000000-0xffffffff]
[    0.542913] bus: 00 [mem 0x180000000-0xfcffffffff]
[    0.542996] ACPI: bus type PCI registered
[    0.547006] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.553580] PCI: Using configuration type 1 for base access
[    0.559150] PCI: Using configuration type 1 for extended access
[    0.577209] ACPI: Added _OSI(Module Device)
[    0.581396] ACPI: Added _OSI(Processor Device)
[    0.585836] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.590539] ACPI: Added _OSI(Processor Aggregator Device)
[    0.596917] ACPI: Executed 1 blocks of module-level executable AML code
[    0.605910] ACPI: Interpreter enabled
[    0.609585] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[    0.618833] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20140424/hwxface-580)
[    0.628079] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S4_] (20140424/hwxface-580)
[    0.637326] ACPI: (supports S0 S1 S5)
[    0.640987] ACPI: Using IOAPIC for interrupt routing
[    0.645995] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.670780] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-05])
[    0.676965] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.685168] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.716725] acpi PNP0A03:00: host bridge window expanded to [io  0x0000-0x0cf7]; [io  0x03b0-0x03df] ignored
[    0.726727] PCI host bridge to bus 0000:00
[    0.730825] pci_bus 0000:00: root bus resource [bus 00-05]
[    0.736306] pci_bus 0000:00: root bus resource [io  0x0d00-0x3fff]
[    0.742484] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.749355] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfbffffff]
[    0.756224] pci_bus 0000:00: root bus resource [mem 0xfc000000-0xfc3fffff]
[    0.763093] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.769284] pci 0000:00:00.0: [10de:005e] type 00 class 0x058000
[    0.769439] pci 0000:00:01.0: [10de:0051] type 00 class 0x060100
[    0.769447] pci 0000:00:01.0: reg 0x10: [io  0x2c00-0x2c7f]
[    0.769561] pci 0000:00:01.1: [10de:0052] type 00 class 0x0c0500
[    0.769571] pci 0000:00:01.1: reg 0x10: [io  0x3000-0x301f]
[    0.769583] pci 0000:00:01.1: reg 0x20: [io  0x2c80-0x2cbf]
[    0.769590] pci 0000:00:01.1: reg 0x24: [io  0x2cc0-0x2cff]
[    0.769607] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.769710] pci 0000:00:02.0: [10de:005a] type 00 class 0x0c0310
[    0.769720] pci 0000:00:02.0: reg 0x10: [mem 0xfc300000-0xfc300fff]
[    0.769748] pci 0000:00:02.0: supports D1 D2
[    0.769750] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.769795] pci 0000:00:02.0: System wakeup disabled by ACPI
[    0.775510] pci 0000:00:02.1: [10de:005b] type 00 class 0x0c0320
[    0.775521] pci 0000:00:02.1: reg 0x10: [mem 0xfc303000-0xfc3030ff]
[    0.775554] pci 0000:00:02.1: supports D1 D2
[    0.775557] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.775601] pci 0000:00:02.1: System wakeup disabled by ACPI
[    0.781319] pci 0000:00:06.0: [10de:0053] type 00 class 0x01018a
[    0.781338] pci 0000:00:06.0: reg 0x20: [io  0x3020-0x302f]
[    0.781349] pci 0000:00:06.0: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.788480] pci 0000:00:06.0: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.795002] pci 0000:00:06.0: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.802132] pci 0000:00:06.0: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.808751] pci 0000:00:07.0: [10de:0054] type 00 class 0x010185
[    0.808762] pci 0000:00:07.0: reg 0x10: [io  0x3050-0x3057]
[    0.808767] pci 0000:00:07.0: reg 0x14: [io  0x3070-0x3073]
[    0.808772] pci 0000:00:07.0: reg 0x18: [io  0x3058-0x305f]
[    0.808777] pci 0000:00:07.0: reg 0x1c: [io  0x3074-0x3077]
[    0.808782] pci 0000:00:07.0: reg 0x20: [io  0x3030-0x303f]
[    0.808787] pci 0000:00:07.0: reg 0x24: [mem 0xfc301000-0xfc301fff]
[    0.808881] pci 0000:00:08.0: [10de:0055] type 00 class 0x010185
[    0.808892] pci 0000:00:08.0: reg 0x10: [io  0x3060-0x3067]
[    0.808896] pci 0000:00:08.0: reg 0x14: [io  0x3078-0x307b]
[    0.808901] pci 0000:00:08.0: reg 0x18: [io  0x3068-0x306f]
[    0.808906] pci 0000:00:08.0: reg 0x1c: [io  0x307c-0x307f]
[    0.808910] pci 0000:00:08.0: reg 0x20: [io  0x3040-0x304f]
[    0.808915] pci 0000:00:08.0: reg 0x24: [mem 0xfc302000-0xfc302fff]
[    0.809012] pci 0000:00:09.0: [10de:005c] type 01 class 0x060400
[    0.809073] pci 0000:00:09.0: System wakeup disabled by ACPI
[    0.814790] pci 0000:00:0b.0: [10de:005d] type 01 class 0x060400
[    0.814834] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.814878] pci 0000:00:0b.0: System wakeup disabled by ACPI
[    0.820601] pci 0000:00:0c.0: [10de:005d] type 01 class 0x060400
[    0.820636] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.820685] pci 0000:00:0c.0: System wakeup disabled by ACPI
[    0.826401] pci 0000:00:0d.0: [10de:005d] type 01 class 0x060400
[    0.826435] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.826486] pci 0000:00:0d.0: System wakeup disabled by ACPI
[    0.832203] pci 0000:00:0e.0: [10de:005d] type 01 class 0x060400
[    0.832236] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.832282] pci 0000:00:0e.0: System wakeup disabled by ACPI
[    0.838006] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000
[    0.838108] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000
[    0.838210] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000
[    0.838302] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000
[    0.838398] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000
[    0.838494] pci 0000:00:19.0: [1022:1200] type 00 class 0x060000
[    0.838601] pci 0000:00:19.1: [1022:1201] type 00 class 0x060000
[    0.838692] pci 0000:00:19.2: [1022:1202] type 00 class 0x060000
[    0.838786] pci 0000:00:19.3: [1022:1203] type 00 class 0x060000
[    0.838884] pci 0000:00:19.4: [1022:1204] type 00 class 0x060000
[    0.839035] pci 0000:01:04.0: [18ca:0020] type 00 class 0x030000
[    0.839051] pci 0000:01:04.0: reg 0x10: [mem 0xf8000000-0xfbffffff pref]
[    0.839061] pci 0000:01:04.0: reg 0x14: [mem 0xfc000000-0xfc03ffff]
[    0.839072] pci 0000:01:04.0: reg 0x18: [io  0x1000-0x107f]
[    0.839109] pci 0000:01:04.0: supports D1 D2
[    0.839178] pci 0000:00:09.0: PCI bridge to [bus 01]
[    0.844144] pci 0000:00:09.0:   bridge window [io  0x1000-0x1fff]
[    0.844147] pci 0000:00:09.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    0.844151] pci 0000:00:09.0:   bridge window [mem 0xf8000000-0xfbffffff pref]
[    0.844227] pci 0000:02:00.0: [14e4:1659] type 00 class 0x020000
[    0.844245] pci 0000:02:00.0: reg 0x10: [mem 0xfc100000-0xfc10ffff 64bit]
[    0.844273] pci 0000:02:00.0: reg 0x30: [mem 0x7b620000-0x7b62ffff pref]
[    0.844340] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.844422] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.854417] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    0.859375] pci 0000:00:0b.0:   bridge window [mem 0xfc100000-0xfc1fffff]
[    0.859451] pci 0000:03:00.0: [14e4:1659] type 00 class 0x020000
[    0.859469] pci 0000:03:00.0: reg 0x10: [mem 0xfc200000-0xfc20ffff 64bit]
[    0.859557] pci 0000:03:00.0: PME# supported from D3hot D3cold
[    0.859637] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.869628] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    0.874589] pci 0000:00:0c.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    0.874650] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    0.879669] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    0.884645] pci_bus 0000:00: on NUMA node 0
[    0.884743] ACPI: PCI Interrupt Link [LNKA] (IRQs *16 17 18 19)
[    0.890844] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 *17 18 19)
[    0.896952] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[    0.904216] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[    0.911488] ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled.
[    0.918764] ACPI: PCI Interrupt Link [LLAS] (IRQs 20 21 22 23) *0, disabled.
[    0.926037] ACPI: PCI Interrupt Link [LUOH] (IRQs 20 21 22 *23)
[    0.932133] ACPI: PCI Interrupt Link [LUEH] (IRQs 20 21 *22 23)
[    0.938242] ACPI: PCI Interrupt Link [LAUD] (IRQs 20 21 22 23) *0, disabled.
[    0.945515] ACPI: PCI Interrupt Link [LMOD] (IRQs 20 21 22 23) *0, disabled.
[    0.952788] ACPI: PCI Interrupt Link [LPA0] (IRQs 20 21 22 23) *0, disabled.
[    0.960057] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 *21 22 23)
[    0.966150] ACPI: PCI Interrupt Link [LSA1] (IRQs *20 21 22 23)
[    0.972261] ACPI: PCI Interrupt Link [LEMA] (IRQs 20 21 22 23) *0, disabled.
[    0.979528] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *0, disabled.
[    0.986805] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *0, disabled.
[    0.994072] ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    1.002574] ACPI: PCI Interrupt Link [LNIA] (IRQs 16) *0, disabled.
[    1.009001] ACPI: PCI Interrupt Link [LNIB] (IRQs 17) *0, disabled.
[    1.015433] ACPI: PCI Interrupt Link [LNIC] (IRQs 18) *0, disabled.
[    1.021868] ACPI: PCI Interrupt Link [LNND] (IRQs 19) *0, disabled.
[    1.028598] ACPI: Enabled 1 GPEs in block 00 to 1F
[    1.033663] vgaarb: setting as boot device: PCI:0000:01:04.0
[    1.039326] vgaarb: device added: PCI:0000:01:04.0,decodes=io+mem,owns=io+mem,locks=none
[    1.047415] vgaarb: loaded
[    1.050120] vgaarb: bridge control possible 0000:01:04.0
[    1.055573] PCI: Using ACPI for IRQ routing
[    1.059760] PCI: pci_cache_line_size set to 64 bytes
[    1.059819] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    1.059823] e820: reserve RAM buffer [mem 0xbff9a000-0xbfffffff]
[    1.060115] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    1.067158] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    1.072186] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    1.080236] Switched to clocksource hpet
[    1.095801] pnp: PnP ACPI init
[    1.098903] ACPI: bus type PNP registered
[    1.103414] pnp 00:00: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    1.103499] pnp 00:01: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[    1.103580] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.103652] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.103688] pnp 00:04: [dma 2]
[    1.103722] pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
[    1.103754] pnp: PnP ACPI: found 5 devices
[    1.107850] ACPI: bus type PNP unregistered
[    1.119017] pci 0000:02:00.0: can't claim BAR 6 [mem 0x7b620000-0x7b62ffff pref]: no compatible bridge window
[    1.128960] pci 0000:00:09.0: PCI bridge to [bus 01]
[    1.133928] pci 0000:00:09.0:   bridge window [io  0x1000-0x1fff]
[    1.140019] pci 0000:00:09.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    1.146803] pci 0000:00:09.0:   bridge window [mem 0xf8000000-0xfbffffff pref]
[    1.154034] pci 0000:02:00.0: BAR 6: assigned [mem 0xfc110000-0xfc11ffff pref]
[    1.161254] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    1.166216] pci 0000:00:0b.0:   bridge window [mem 0xfc100000-0xfc1fffff]
[    1.173003] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    1.177965] pci 0000:00:0c.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    1.184751] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    1.189715] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    1.194681] pci_bus 0000:00: resource 4 [io  0x0d00-0x3fff]
[    1.194684] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[    1.194687] pci_bus 0000:00: resource 6 [mem 0xf8000000-0xfbffffff]
[    1.194689] pci_bus 0000:00: resource 7 [mem 0xfc000000-0xfc3fffff]
[    1.194691] pci_bus 0000:00: resource 8 [io  0x0000-0x0cf7]
[    1.194694] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]
[    1.194697] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfc0fffff]
[    1.194699] pci_bus 0000:01: resource 2 [mem 0xf8000000-0xfbffffff pref]
[    1.194702] pci_bus 0000:02: resource 1 [mem 0xfc100000-0xfc1fffff]
[    1.194705] pci_bus 0000:03: resource 1 [mem 0xfc200000-0xfc2fffff]
[    1.194787] NET: Registered protocol family 2
[    1.199544] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    1.207192] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    1.214523] TCP: Hash tables configured (established 65536 bind 65536)
[    1.221126] TCP: reno registered
[    1.224375] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    1.230584] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    1.237313] NET: Registered protocol family 1
[    1.242047] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[    1.248119] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[    1.254004] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.259526] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.265012] pci 0000:00:0b.0: Found disabled HT MSI Mapping
[    1.270587] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.276109] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.281602] pci 0000:00:0c.0: Found disabled HT MSI Mapping
[    1.287176] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.292707] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.298194] pci 0000:00:0d.0: Found disabled HT MSI Mapping
[    1.303766] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.309292] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.314776] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[    1.320348] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.325857] pci 0000:01:04.0: Video device with shadowed ROM
[    1.325866] PCI: CLS 64 bytes, default 64
[    1.325966] Unpacking initramfs...
[    1.704122] Freeing initrd memory: 14028K (ffff88007f24c000 - ffff88007ffff000)
[    1.712040] PCI-DMA: Disabling AGP.
[    1.715674] PCI-DMA: aperture base @ b4000000 size 65536 KB
[    1.721253] PCI-DMA: using GART IOMMU.
[    1.725014] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    1.736837] platform rtc_cmos: registered platform RTC device (no PNP device found)
[    1.744655] microcode: CPU0: patch_level=0x01000084
[    1.749546] microcode: CPU1: patch_level=0x01000084
[    1.754541] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.763333] LVT offset 1 assigned for vector 0x400
[    1.768134] IBS: LVT offset 1 assigned
[    1.771909] perf: AMD IBS detected (0x00000007)
[    1.776909] futex hash table entries: 512 (order: 3, 32768 bytes)
[    1.783057] audit: initializing netlink subsys (disabled)
[    1.788481] audit: type=2000 audit(1490116155.536:1): initialized
[    1.795321] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.801721] zbud: loaded
[    1.804514] VFS: Disk quotas dquot_6.5.2
[    1.808464] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.814990] msgmni has been set to 9946
[    1.819349] alg: No test for stdrng (krng)
[    1.823505] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.830981] io scheduler noop registered
[    1.834913] io scheduler deadline registered
[    1.839239] io scheduler cfq registered (default)
[    1.844157] pcieport 0000:00:0b.0: irq 40 for MSI/MSI-X
[    1.844281] pcieport 0000:00:0c.0: irq 41 for MSI/MSI-X
[    1.844389] pcieport 0000:00:0d.0: irq 42 for MSI/MSI-X
[    1.844494] pcieport 0000:00:0e.0: irq 43 for MSI/MSI-X
[    1.844647] aer 0000:00:0b.0:pcie02: service driver aer loaded
[    1.844674] aer 0000:00:0c.0:pcie02: service driver aer loaded
[    1.844702] aer 0000:00:0d.0:pcie02: service driver aer loaded
[    1.844728] aer 0000:00:0e.0:pcie02: service driver aer loaded
[    1.844750] pcieport 0000:00:0b.0: Signaling PME through PCIe PME interrupt
[    1.851708] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[    1.858230] pcie_pme 0000:00:0b.0:pcie01: service driver pcie_pme loaded
[    1.858240] pcieport 0000:00:0c.0: Signaling PME through PCIe PME interrupt
[    1.865194] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[    1.871718] pcie_pme 0000:00:0c.0:pcie01: service driver pcie_pme loaded
[    1.871729] pcieport 0000:00:0d.0: Signaling PME through PCIe PME interrupt
[    1.878683] pcie_pme 0000:00:0d.0:pcie01: service driver pcie_pme loaded
[    1.878692] pcieport 0000:00:0e.0: Signaling PME through PCIe PME interrupt
[    1.885647] pcie_pme 0000:00:0e.0:pcie01: service driver pcie_pme loaded
[    1.885679] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.891273] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.897981] GHES: HEST is not enabled!
[    1.901868] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.928439] 00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.956076] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[    1.963944] Linux agpgart interface v0.103
[    1.968189] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f03:MOU] at 0x60,0x64 irq 1,12
[    1.978329] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.983303] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.988542] mousedev: PS/2 mouse device common for all mice
[    1.994220] rtc_cmos rtc_cmos: RTC can wake from S4
[    1.999277] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[    2.005671] rtc_cmos rtc_cmos: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    2.013531] ledtrig-cpu: registered to indicate activity on CPUs
[    2.019718] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[    2.026159] AMD IOMMUv2 functionality not available on this system
[    2.032479] TCP: cubic registered
[    2.035867] NET: Registered protocol family 10
[    2.040700] mip6: Mobile IPv6
[    2.043673] NET: Registered protocol family 17
[    2.048194] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    2.056958] mpls_gso: MPLS GSO support
[    2.061163] registered taskstats version 1
[    2.065952] rtc_cmos rtc_cmos: setting system clock to 2017-03-21 17:09:17 UTC (1490116157)
[    2.074368] PM: Hibernation image not present or could not be loaded.
[    2.076292] Freeing unused kernel memory: 1204K (ffffffff818ee000 - ffffffff81a1b000)
[    2.084117] Write protecting the kernel read-only data: 8192k
[    2.093310] Freeing unused kernel memory: 924K (ffff880001519000 - ffff880001600000)
[    2.101876] Freeing unused kernel memory: 216K (ffff8800017ca000 - ffff880001800000)
[    2.132813] systemd-udevd[63]: starting version 215
[    2.138535] random: systemd-udevd urandom read with 3 bits of entropy available
[    2.158424] ACPI: bus type USB registered
[    2.167365] usbcore: registered new interface driver usbfs
[    2.174264] SCSI subsystem initialized
[    2.176675] usbcore: registered new interface driver hub
[    2.176748] usbcore: registered new device driver usb
[    2.192982] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.204648] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.211901] libata version 3.00 loaded.
[    2.212634] sata_nv 0000:00:07.0: version 3.5
[    2.213405] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
[    2.220426] ehci-pci: EHCI PCI platform driver
[    2.220996] FDC 0 is a post-1991 82077
[    2.227939] pps_core: LinuxPPS API ver. 1 registered
[    2.227940] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.243857] PTP clock support registered
[    2.248182] scsi0 : sata_nv
[    2.251305] scsi1 : sata_nv
[    2.254328] ata1: SATA max UDMA/133 cmd 0x3050 ctl 0x3070 bmdma 0x3030 irq 21
[    2.261534] ata2: SATA max UDMA/133 cmd 0x3058 ctl 0x3074 bmdma 0x3038 irq 21
[    2.271373] ehci-pci 0000:00:02.1: EHCI Host Controller
[    2.277428] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 1
[    2.286474] tg3.c:v3.137 (May 11, 2014)
[    2.290328] tg3 0000:02:00.0: enabling device (0004 -> 0006)
[    2.296840] ACPI: PCI Interrupt Link [LNIB] enabled at IRQ 17
[    2.306775] ehci-pci 0000:00:02.1: debug port 1
[    2.333856] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM95721) rev 4201] (PCI Express) MAC address 00:1e:8c:51:61:a2
[    2.337304] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[    2.337345] ehci-pci 0000:00:02.1: irq 22, io mem 0xfc303000
[    2.343827] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    2.343914] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.343916] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.343917] usb usb1: Product: EHCI Host Controller
[    2.343919] usb usb1: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    2.343920] usb usb1: SerialNumber: 0000:00:02.1
[    2.344215] hub 1-0:1.0: USB hub found
[    2.344301] hub 1-0:1.0: 10 ports detected
[    2.392932] tg3 0000:02:00.0 eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    2.402677] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.410537] tg3 0000:02:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.417357] pata_amd 0000:00:06.0: version 0.4.1
[    2.417890] ohci-pci: OHCI PCI platform driver
[    2.417913] scsi2 : pata_amd
[    2.418028] scsi3 : pata_amd
[    2.418088] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x3020 irq 14
[    2.418089] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x3028 irq 15
[    2.418101] tg3 0000:03:00.0: enabling device (0004 -> 0006)
[    2.418244] ACPI: PCI Interrupt Link [LNIA] enabled at IRQ 16
[    2.453994] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 20
[    2.460610] scsi4 : sata_nv
[    2.463560] scsi5 : sata_nv
[    2.466429] ata5: SATA max UDMA/133 cmd 0x3060 ctl 0x3078 bmdma 0x3040 irq 20
[    2.473562] ata6: SATA max UDMA/133 cmd 0x3068 ctl 0x307c bmdma 0x3048 irq 20
[    2.483192] ohci-pci 0000:00:02.0: OHCI PCI host controller
[    2.488790] ohci-pci 0000:00:02.0: new USB bus registered, assigned bus number 2
[    2.496270] ohci-pci 0000:00:02.0: irq 23, io mem 0xfc300000
[    2.507365] tg3 0000:03:00.0 eth1: Tigon3 [partno(BCM95721) rev 4201] (PCI Express) MAC address 00:1e:8c:51:63:95
[    2.517620] tg3 0000:03:00.0 eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    2.527349] tg3 0000:03:00.0 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.535172] tg3 0000:03:00.0 eth1: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.557812] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.564597] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.571812] usb usb2: Product: OHCI PCI host controller
[    2.577035] usb usb2: Manufacturer: Linux 3.16.0-4-amd64 ohci_hcd
[    2.583123] usb usb2: SerialNumber: 0000:00:02.0
[    2.588176] ata1: SATA link down (SStatus 0 SControl 300)
[    2.588308] hub 2-0:1.0: USB hub found
[    2.588316] hub 2-0:1.0: 10 ports detected
[    2.735678] tsc: Refined TSC clocksource calibration: 1909.786 MHz
[    2.791666] ata5: SATA link down (SStatus 0 SControl 300)
[    2.911618] ata2: SATA link down (SStatus 0 SControl 300)
[    3.391447] ata6: SATA link down (SStatus 0 SControl 300)
[    3.414743] FS-Cache: Loaded
[    3.422840] RPC: Registered named UNIX socket transport module.
[    3.430077] RPC: Registered udp transport module.
[    3.436154] RPC: Registered tcp transport module.
[    3.442237] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    3.455452] FS-Cache: Netfs 'nfs' registered for caching
[    3.471882] tg3 0000:02:00.0: irq 44 for MSI/MSI-X
[    3.503867] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    3.739435] Switched to clocksource tsc
[    6.644454] tg3 0000:02:00.0 eth0: Link is up at 1000 Mbps, full duplex
[    6.651060] tg3 0000:02:00.0 eth0: Flow control is on for TX and on for RX
[    6.657936] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.651965] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    7.665785] systemd[1]: Detected architecture 'x86-64'.
[    7.711283] systemd[1]: Inserted module 'autofs4'
[    7.718022] systemd[1]: Set hostname to <cb-test-tgt>.
[    7.874276] systemd[1]: Cannot add dependency job for unit dbus.socket, ignoring: Unit dbus.socket failed to load: No such file or directory.
[    7.886994] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    7.902365] systemd[1]: Expecting device dev-ttyS0.device...
[    7.918064] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    7.925886] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    7.933496] systemd[1]: Starting Remote File Systems (Pre).
[    7.949909] systemd[1]: Reached target Remote File Systems (Pre).
[    7.956046] systemd[1]: Starting Encrypted Volumes.
[    7.969895] systemd[1]: Reached target Encrypted Volumes.
[    7.975347] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    7.997884] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    8.007297] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[    8.015377] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    8.023313] systemd[1]: Starting Paths.
[    8.037871] systemd[1]: Reached target Paths.
[    8.042321] systemd[1]: Starting Swap.
[    8.053863] systemd[1]: Reached target Swap.
[    8.058153] systemd[1]: Starting Root Slice.
[    8.069861] systemd[1]: Created slice Root Slice.
[    8.074586] systemd[1]: Starting User and Session Slice.
[    8.089859] systemd[1]: Created slice User and Session Slice.
[    8.095622] systemd[1]: Starting Delayed Shutdown Socket.
[    8.109846] systemd[1]: Listening on Delayed Shutdown Socket.
[    8.115610] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[    8.133840] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    8.140835] systemd[1]: Starting Journal Socket (/dev/log).
[    8.157831] systemd[1]: Listening on Journal Socket (/dev/log).
[    8.163786] systemd[1]: Starting udev Kernel Socket.
[    8.177820] systemd[1]: Listening on udev Kernel Socket.
[    8.183156] systemd[1]: Starting udev Control Socket.
[    8.197815] systemd[1]: Listening on udev Control Socket.
[    8.203243] systemd[1]: Starting Journal Socket.
[    8.217805] systemd[1]: Listening on Journal Socket.
[    8.222802] systemd[1]: Starting System Slice.
[    8.237806] systemd[1]: Created slice System Slice.
[    8.242708] systemd[1]: Starting system-getty.slice.
[    8.257797] systemd[1]: Created slice system-getty.slice.
[    8.263209] systemd[1]: Starting system-serial\x2dgetty.slice.
[    8.277790] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    8.284093] systemd[1]: Starting Increase datagram queue length...
[    8.302629] systemd[1]: Starting udev Coldplug all Devices...
[    8.337219] systemd[1]: Starting Load Kernel Modules...
[    8.352780] systemd[1]: Started Set Up Additional Binary Formats.
[    8.359350] systemd[1]: Mounting Debug File System...
[    8.374864] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    8.398554] systemd[1]: Mounting POSIX Message Queue File System...
[    8.414447] systemd[1]: Mounting Huge Pages File System...
[    8.430615] systemd[1]: Starting Slices.
[    8.441805] systemd[1]: Reached target Slices.
[    8.446342] systemd[1]: Starting Remount Root and Kernel File Systems...
[    8.473806] systemd[1]: Mounted Huge Pages File System.
[    8.489722] systemd[1]: Mounted POSIX Message Queue File System.
[    8.505724] systemd[1]: Mounted Debug File System.
[    8.521719] systemd[1]: Started Increase datagram queue length.
[    8.537849] systemd[1]: Started Load Kernel Modules.
[    8.557830] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    8.577803] systemd[1]: Started Remount Root and Kernel File Systems.
[    8.593696] systemd[1]: Started udev Coldplug all Devices.
[    8.638574] systemd[1]: Started Various fixups to make systemd work better on Debian.
[    8.646443] systemd[1]: Starting Load/Save Random Seed...
[    8.662735] systemd[1]: Starting Create Static Device Nodes in /dev...
[    8.682577] systemd[1]: Starting Apply Kernel Variables...
[    8.698528] systemd[1]: Mounted Configuration File System.
[    8.704236] systemd[1]: Mounted FUSE Control File System.
[    8.709670] systemd[1]: Starting Syslog Socket.
[    8.725643] systemd[1]: Listening on Syslog Socket.
[    8.730552] systemd[1]: Starting Sockets.
[    8.741629] systemd[1]: Reached target Sockets.
[    8.746187] systemd[1]: Starting Journal Service...
[    8.769692] systemd[1]: Started Journal Service.
[    8.847815] systemd-udevd[162]: starting version 215
[    8.967177] systemd-journald[161]: Received request to flush runtime journal from PID 1
[    9.007067] acpi-cpufreq: overriding BIOS provided _PSD data
[    9.007445] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    9.021075] i2c i2c-0: nForce2 SMBus adapter at 0x2c80
[    9.028483] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    9.037543] i2c i2c-1: nForce2 SMBus adapter at 0x2cc0
[    9.044767] ACPI: Power Button [PWRB]
[    9.049999] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    9.060479] ACPI: Power Button [PWRF]
[    9.098377] k10temp 0000:00:18.3: unreliable CPU thermal sensor; monitoring disabled
[    9.106888] EDAC MC: Ver: 3.0.0
[    9.110122] k10temp 0000:00:19.3: unreliable CPU thermal sensor; monitoring disabled
[    9.135992] MCE: In-kernel MCE decoding enabled.
[    9.143129] input: PC Speaker as /devices/platform/pcspkr/input/input4
[    9.156686] AMD64 EDAC driver v3.4.0
[    9.173068] EDAC amd64: DRAM ECC enabled.
[    9.187497] EDAC amd64: F10h detected (node 0).
[    9.190923] kvm: Nested Virtualization enabled
[    9.190925] kvm: Nested Paging enabled
[    9.200327] EDAC MC: DCT0 chip selects:
[    9.200329] EDAC amd64: MC: 0:     0MB 1:     0MB
[    9.205101] EDAC amd64: MC: 2:     0MB 3:     0MB
[    9.209854] EDAC amd64: MC: 4:     0MB 5:     0MB
[    9.214566] EDAC amd64: MC: 6:  2048MB 7:  2048MB
[    9.219284] EDAC MC: DCT1 chip selects:
[    9.219297] EDAC amd64: MC: 0:     0MB 1:     0MB
[    9.223999] EDAC amd64: MC: 2:     0MB 3:     0MB
[    9.228719] EDAC amd64: MC: 4:     0MB 5:     0MB
[    9.233420] EDAC amd64: MC: 6:  1024MB 7:  1024MB
[    9.238135] EDAC amd64: using x4 syndromes.
[    9.245493] EDAC amd64: CS6: Registered DDR2 RAM
[    9.250121] EDAC amd64: CS7: Registered DDR2 RAM
[    9.255052] EDAC MC0: Giving out device to module amd64_edac controller F10h: DEV 0000:00:18.2 (INTERRUPT)
[    9.268803] EDAC amd64: DRAM ECC enabled.
[    9.273874] EDAC amd64: F10h detected (node 1).
[    9.278452] EDAC MC: DCT0 chip selects:
[    9.278455] EDAC amd64: MC: 0:  1024MB 1:     0MB
[    9.283162] EDAC amd64: MC: 2:     0MB 3:     0MB
[    9.287877] EDAC amd64: MC: 4:     0MB 5:     0MB
[    9.292591] EDAC amd64: MC: 6:     0MB 7:     0MB
[    9.297300] EDAC MC: DCT1 chip selects:
[    9.297301] EDAC amd64: MC: 0:     0MB 1:     0MB
[    9.302013] EDAC amd64: MC: 2:     0MB 3:     0MB
[    9.306725] EDAC amd64: MC: 4:     0MB 5:     0MB
[    9.311429] EDAC amd64: MC: 6:     0MB 7:     0MB
[    9.316136] EDAC amd64: using x4 syndromes.
[    9.320328] EDAC amd64: MCT channel count: 1
[    9.324803] EDAC amd64: CS0: Registered DDR2 RAM
[    9.329847] EDAC MC1: Giving out device to module amd64_edac controller F10h: DEV 0000:00:19.2 (INTERRUPT)
[    9.339809] EDAC PCI0: Giving out device to module amd64_edac controller EDAC PCI controller: DEV 0000:00:18.2 (POLLED)
[    9.438401] random: nonblocking pool is initialized
[   39.580227] *****RAPTOR ENGINEERING AUTOMATED TEST BOOT SUCCESS*****