[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt9-2 (2015-04-13)
[    0.000000] Command line: root=/dev/nfs initrd=initrd-cb-test-tgt-i386 rootfstype=nfs nfsroot=10.100.1.100:/nfsroots/cb-test-tgt-01,v3,hard,nointr,tcp ip=10.100.1.10::10.100.1.1:255.255.255.0:embed-o-matic:eth0:off console=ttyS0,115200n8 consoleblank=0 rw BOOT_IMAGE=vmlinuz-cb-test-tgt-i386 
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bff99fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bff9a000-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: ASUS KFSN4-DRE/KFSN4-DRE, BIOS RAPTOR-NORMAL 03/29/2017
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] AGP: No AGP bridge found
[    0.000000] e820: last_pfn = 0x180000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-back
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000F8000000 mask FFFFFC000000 write-combining
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000180000000 aka 6144M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0xbff9a max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f0690-0x000f069f] mapped at [ffff8800000f0690]
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01af4000, 0x01af4fff] PGTABLE
[    0.000000] BRK [0x01af5000, 0x01af5fff] PGTABLE
[    0.000000] BRK [0x01af6000, 0x01af6fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x17fe00000-0x17fffffff]
[    0.000000]  [mem 0x17fe00000-0x17fffffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x17c000000-0x17fdfffff]
[    0.000000]  [mem 0x17c000000-0x17fdfffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x100000000-0x17bffffff]
[    0.000000]  [mem 0x100000000-0x17bffffff] page 1G
[    0.000000] init_memory_mapping: [mem 0x00100000-0xbff99fff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x3fffffff] page 2M
[    0.000000]  [mem 0x40000000-0x7fffffff] page 1G
[    0.000000]  [mem 0x80000000-0xbfdfffff] page 2M
[    0.000000]  [mem 0xbfe00000-0xbff99fff] page 4k
[    0.000000] RAMDISK: [mem 0x7f24c000-0x7fffefff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F07F0 000024 (v02 CORE  )
[    0.000000] ACPI: XSDT 0x00000000BFFAB0E0 00006C (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: FACP 0x00000000BFFAD910 000074 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: DSDT 0x00000000BFFAB280 002687 (v02 ASUS   COREBOOT 00000001 INTL 20160831)
[    0.000000] ACPI: FACS 0x00000000BFFAB240 000040
[    0.000000] ACPI: SSDT 0x00000000BFFADA10 000E1E (v02 CORE   COREBOOT 0000002A CORE 0000002A)
[    0.000000] ACPI: TCPA 0x00000000BFFAE830 000032 (v02 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: APIC 0x00000000BFFAE870 000072 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SRAT 0x00000000BFFAE8F0 0000F0 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SLIT 0x00000000BFFAE9E0 000030 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: HPET 0x00000000BFFAEA10 000038 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SRAT 0x00000000BFFAEA50 0000F0 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: SLIT 0x00000000BFFAEB40 000030 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] SRAT: PXM 0 -> APIC 0x00 -> Node 0
[    0.000000] SRAT: PXM 1 -> APIC 0x04 -> Node 1
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x00000000-0x0009ffff]
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x00100000-0xbfffffff]
[    0.000000] SRAT: Node 0 PXM 0 [mem 0x100000000-0x13fffffff]
[    0.000000] SRAT: Node 1 PXM 1 [mem 0x140000000-0x17fffffff]
[    0.000000] NUMA: Initialized distance table, cnt=2
[    0.000000] NUMA: Node 0 [mem 0x00000000-0x0009ffff] + [mem 0x00100000-0xbfffffff] -> [mem 0x00000000-0xbfffffff]
[    0.000000] NUMA: Node 0 [mem 0x00000000-0xbfffffff] + [mem 0x100000000-0x13fffffff] -> [mem 0x00000000-0x13fffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x13fffffff]
[    0.000000]   NODE_DATA [mem 0x13fffb000-0x13fffffff]
[    0.000000] Initmem setup node 1 [mem 0x140000000-0x17fffffff]
[    0.000000]   NODE_DATA [mem 0x17fff8000-0x17fffcfff]
[    0.000000]  [ffffea0000000000-ffffea00045fffff] PMD -> [ffff88013be00000-ffff88013f5fffff] on node 0
[    0.000000]  [ffffea0004600000-ffffea00053fffff] PMD -> [ffff88017e600000-ffff88017f3fffff] on node 1
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x17fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0xbff99fff]
[    0.000000]   node   0: [mem 0x100000000-0x13fffffff]
[    0.000000]   node   1: [mem 0x140000000-0x17fffffff]
[    0.000000] On node 0 totalpages: 1048376
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10695 pages used for memmap
[    0.000000]   DMA32 zone: 782234 pages, LIFO batch:31
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 262144 pages, LIFO batch:31
[    0.000000] On node 1 totalpages: 262144
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 262144 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x2008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x18] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 24, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xbff9a000-0xcfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xffffffff]
[    0.000000] e820: [mem 0xd0000000-0xffffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:2
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88013fc00000 s80896 r8192 d21504 u2097152
[    0.000000] pcpu-alloc: s80896 r8192 d21504 u2097152 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 [1] 1 
[    0.000000] Built 2 zonelists in Node order, mobility grouping on.  Total pages: 1292580
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=/dev/nfs initrd=initrd-cb-test-tgt-i386 rootfstype=nfs nfsroot=10.100.1.100:/nfsroots/cb-test-tgt-01,v3,hard,nointr,tcp ip=10.100.1.10::10.100.1.1:255.255.255.0:embed-o-matic:eth0:off console=ttyS0,115200n8 consoleblank=0 rw BOOT_IMAGE=vmlinuz-cb-test-tgt-i386 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] AGP: Node 0: aperture [bus addr 0xf5ea000000-0xf5ebffffff] (32MB)
[    0.000000] Aperture beyond 4GB. Ignoring.
[    0.000000] AGP: Your BIOS doesn't leave a aperture memory hole
[    0.000000] AGP: Please enable the IOMMU option in the BIOS setup
[    0.000000] AGP: This costs you 64MB of RAM
[    0.000000] AGP: Mapping aperture over RAM [mem 0xb4000000-0xb7ffffff] (65536KB)
[    0.000000] PM: Registered nosave memory: [mem 0xb4000000-0xb7ffffff]
[    0.000000] Memory: 5012856K/5242080K available (5207K kernel code, 946K rwdata, 1832K rodata, 1204K init, 840K bss, 229224K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:33024 nr_irqs:512 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour *CGA 80x25
[    0.000000] console [ttyS0] enabled
[    0.000000] mempolicy: Disabling automatic NUMA balancing. Configure with numa_balancing= or the kernel.numa_balancing sysctl
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1909.734 MHz processor
[    0.000149] Calibrating delay loop (skipped), value calculated using timer frequency.. 3819.46 BogoMIPS (lpj=7638936)
[    0.010769] pid_max: default: 32768 minimum: 301
[    0.015405] ACPI: Core revision 20140424
[    0.021629] ACPI: All ACPI Tables successfully acquired
[    0.026951] Security Framework initialized
[    0.031062] AppArmor: AppArmor disabled by boot time parameter
[    0.036890] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.044324] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.057183] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.066879] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.073773] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.081585] Initializing cgroup subsys memory
[    0.085954] Initializing cgroup subsys devices
[    0.090408] Initializing cgroup subsys freezer
[    0.094853] Initializing cgroup subsys net_cls
[    0.099300] Initializing cgroup subsys blkio
[    0.103579] Initializing cgroup subsys perf_event
[    0.108289] Initializing cgroup subsys net_prio
[    0.112859] tseg: 0000000000
[    0.112869] CPU: Physical Processor ID: 0
[    0.116882] CPU: Processor Core ID: 0
[    0.120542] mce: CPU supports 6 MCE banks
[    0.124568] LVT offset 0 assigned for vector 0xf9
[    0.129277] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8
Last level dTLB entries: 4KB 512, 2MB 128, 4MB 64, 1GB 0
tlb_flushall_shift: 6
[    0.144606] Freeing SMP alternatives memory: 20K (ffffffff81a1b000 - ffffffff81a20000)
[    0.153619] ftrace: allocating 21614 entries in 85 pages
[    0.168796] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=0 pin2=0
[    0.214296] smpboot: CPU0: Quad-Core AMD Opteron(tm) Processor 8347 (fam: 10, model: 02, stepping: 01)
[    0.328536] Performance Events: AMD PMU driver.
[    0.333086] ... version:                0
[    0.337091] ... bit width:              48
[    0.341189] ... generic registers:      4
[    0.345200] ... value mask:             0000ffffffffffff
[    0.350502] ... max period:             00007fffffffffff
[    0.355804] ... fixed-purpose events:   0
[    0.359806] ... event mask:             000000000000000f
[    0.367313] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.375571] x86: Booting SMP configuration:
[    0.379753] .... node  #1, CPUs:      #1
[    0.492550] x86: Booted up 2 nodes, 2 CPUs
[    0.496834] smpboot: Total of 2 processors activated (7639.04 BogoMIPS)
[    0.505287] devtmpfs: initialized
[    0.516420] pinctrl core: initialized pinctrl subsystem
[    0.521800] NET: Registered protocol family 16
[    0.526454] cpuidle: using governor ladder
[    0.530554] cpuidle: using governor menu
[    0.534484] node 0 link 1: io port [1000, 3fff]
[    0.534487] TOM: 00000000c0000000 aka 3072M
[    0.538670] Fam 10h mmconf [mem 0xc0000000-0xcfffffff]
[    0.538674] node 0 link 1: mmio [fc000000, fc3fffff]
[    0.538677] node 0 link 1: mmio [f8000000, fbffffff]
[    0.538680] TOM2: 0000000180000000 aka 6144M
[    0.542950] bus: [bus 00-05] on node 0 link 1
[    0.542952] bus: 00 [io  0x0000-0xffff]
[    0.542953] bus: 00 [mem 0xd0000000-0xffffffff]
[    0.542955] bus: 00 [mem 0x180000000-0xfcffffffff]
[    0.543037] ACPI: bus type PCI registered
[    0.547049] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.553624] PCI: Using configuration type 1 for base access
[    0.559194] PCI: Using configuration type 1 for extended access
[    0.577207] ACPI: Added _OSI(Module Device)
[    0.581394] ACPI: Added _OSI(Processor Device)
[    0.585834] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.590538] ACPI: Added _OSI(Processor Aggregator Device)
[    0.596909] ACPI: Executed 1 blocks of module-level executable AML code
[    0.605885] ACPI: Interpreter enabled
[    0.609558] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[    0.618808] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20140424/hwxface-580)
[    0.628052] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S4_] (20140424/hwxface-580)
[    0.637310] ACPI: (supports S0 S1 S5)
[    0.640971] ACPI: Using IOAPIC for interrupt routing
[    0.645976] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.670740] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-05])
[    0.676922] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.685124] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.716325] acpi PNP0A03:00: host bridge window expanded to [io  0x0000-0x0cf7]; [io  0x03b0-0x03df] ignored
[    0.726318] PCI host bridge to bus 0000:00
[    0.730421] pci_bus 0000:00: root bus resource [bus 00-05]
[    0.735898] pci_bus 0000:00: root bus resource [io  0x0d00-0x3fff]
[    0.742076] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.748946] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfbffffff]
[    0.755815] pci_bus 0000:00: root bus resource [mem 0xfc000000-0xfc3fffff]
[    0.762687] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.768877] pci 0000:00:00.0: [10de:005e] type 00 class 0x058000
[    0.769033] pci 0000:00:01.0: [10de:0051] type 00 class 0x060100
[    0.769040] pci 0000:00:01.0: reg 0x10: [io  0x2c00-0x2c7f]
[    0.769152] pci 0000:00:01.1: [10de:0052] type 00 class 0x0c0500
[    0.769162] pci 0000:00:01.1: reg 0x10: [io  0x3000-0x301f]
[    0.769174] pci 0000:00:01.1: reg 0x20: [io  0x2c80-0x2cbf]
[    0.769181] pci 0000:00:01.1: reg 0x24: [io  0x2cc0-0x2cff]
[    0.769198] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.769300] pci 0000:00:02.0: [10de:005a] type 00 class 0x0c0310
[    0.769308] pci 0000:00:02.0: reg 0x10: [mem 0xfc300000-0xfc300fff]
[    0.769344] pci 0000:00:02.0: supports D1 D2
[    0.769347] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.769392] pci 0000:00:02.0: System wakeup disabled by ACPI
[    0.775111] pci 0000:00:02.1: [10de:005b] type 00 class 0x0c0320
[    0.775121] pci 0000:00:02.1: reg 0x10: [mem 0xfc303000-0xfc3030ff]
[    0.775161] pci 0000:00:02.1: supports D1 D2
[    0.775163] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.775208] pci 0000:00:02.1: System wakeup disabled by ACPI
[    0.780928] pci 0000:00:06.0: [10de:0053] type 00 class 0x01018a
[    0.780945] pci 0000:00:06.0: reg 0x20: [io  0x3020-0x302f]
[    0.780955] pci 0000:00:06.0: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.788080] pci 0000:00:06.0: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.794605] pci 0000:00:06.0: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.801733] pci 0000:00:06.0: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.808356] pci 0000:00:07.0: [10de:0054] type 00 class 0x010185
[    0.808367] pci 0000:00:07.0: reg 0x10: [io  0x3050-0x3057]
[    0.808371] pci 0000:00:07.0: reg 0x14: [io  0x3070-0x3073]
[    0.808376] pci 0000:00:07.0: reg 0x18: [io  0x3058-0x305f]
[    0.808381] pci 0000:00:07.0: reg 0x1c: [io  0x3074-0x3077]
[    0.808385] pci 0000:00:07.0: reg 0x20: [io  0x3030-0x303f]
[    0.808390] pci 0000:00:07.0: reg 0x24: [mem 0xfc301000-0xfc301fff]
[    0.808492] pci 0000:00:08.0: [10de:0055] type 00 class 0x010185
[    0.808503] pci 0000:00:08.0: reg 0x10: [io  0x3060-0x3067]
[    0.808508] pci 0000:00:08.0: reg 0x14: [io  0x3078-0x307b]
[    0.808512] pci 0000:00:08.0: reg 0x18: [io  0x3068-0x306f]
[    0.808517] pci 0000:00:08.0: reg 0x1c: [io  0x307c-0x307f]
[    0.808521] pci 0000:00:08.0: reg 0x20: [io  0x3040-0x304f]
[    0.808526] pci 0000:00:08.0: reg 0x24: [mem 0xfc302000-0xfc302fff]
[    0.808623] pci 0000:00:09.0: [10de:005c] type 01 class 0x060400
[    0.808685] pci 0000:00:09.0: System wakeup disabled by ACPI
[    0.814400] pci 0000:00:0b.0: [10de:005d] type 01 class 0x060400
[    0.814443] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.814488] pci 0000:00:0b.0: System wakeup disabled by ACPI
[    0.820207] pci 0000:00:0c.0: [10de:005d] type 01 class 0x060400
[    0.820242] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.820291] pci 0000:00:0c.0: System wakeup disabled by ACPI
[    0.826009] pci 0000:00:0d.0: [10de:005d] type 01 class 0x060400
[    0.826043] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.826090] pci 0000:00:0d.0: System wakeup disabled by ACPI
[    0.831804] pci 0000:00:0e.0: [10de:005d] type 01 class 0x060400
[    0.831840] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.831886] pci 0000:00:0e.0: System wakeup disabled by ACPI
[    0.837607] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000
[    0.837710] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000
[    0.837808] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000
[    0.837900] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000
[    0.837996] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000
[    0.838093] pci 0000:00:19.0: [1022:1200] type 00 class 0x060000
[    0.838198] pci 0000:00:19.1: [1022:1201] type 00 class 0x060000
[    0.838288] pci 0000:00:19.2: [1022:1202] type 00 class 0x060000
[    0.838383] pci 0000:00:19.3: [1022:1203] type 00 class 0x060000
[    0.838478] pci 0000:00:19.4: [1022:1204] type 00 class 0x060000
[    0.838629] pci 0000:01:04.0: [18ca:0020] type 00 class 0x030000
[    0.838642] pci 0000:01:04.0: reg 0x10: [mem 0xf8000000-0xfbffffff pref]
[    0.838652] pci 0000:01:04.0: reg 0x14: [mem 0xfc000000-0xfc03ffff]
[    0.838659] pci 0000:01:04.0: reg 0x18: [io  0x1000-0x107f]
[    0.838698] pci 0000:01:04.0: supports D1 D2
[    0.838767] pci 0000:00:09.0: PCI bridge to [bus 01]
[    0.843727] pci 0000:00:09.0:   bridge window [io  0x1000-0x1fff]
[    0.843730] pci 0000:00:09.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    0.843734] pci 0000:00:09.0:   bridge window [mem 0xf8000000-0xfbffffff pref]
[    0.843810] pci 0000:02:00.0: [14e4:1659] type 00 class 0x020000
[    0.843828] pci 0000:02:00.0: reg 0x10: [mem 0xfc100000-0xfc10ffff 64bit]
[    0.843857] pci 0000:02:00.0: reg 0x30: [mem 0x68400000-0x6840ffff pref]
[    0.843921] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.843999] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.853991] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    0.858951] pci 0000:00:0b.0:   bridge window [mem 0xfc100000-0xfc1fffff]
[    0.859027] pci 0000:03:00.0: [14e4:1659] type 00 class 0x020000
[    0.859045] pci 0000:03:00.0: reg 0x10: [mem 0xfc200000-0xfc20ffff 64bit]
[    0.859131] pci 0000:03:00.0: PME# supported from D3hot D3cold
[    0.859208] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.869204] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    0.874164] pci 0000:00:0c.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    0.874225] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    0.879244] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    0.884221] pci_bus 0000:00: on NUMA node 0
[    0.884322] ACPI: PCI Interrupt Link [LNKA] (IRQs *16 17 18 19)
[    0.890421] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 *17 18 19)
[    0.896528] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[    0.903796] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[    0.911069] ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled.
[    0.918359] ACPI: PCI Interrupt Link [LLAS] (IRQs 20 21 22 23) *0, disabled.
[    0.925621] ACPI: PCI Interrupt Link [LUOH] (IRQs 20 21 22 *23)
[    0.931719] ACPI: PCI Interrupt Link [LUEH] (IRQs 20 21 *22 23)
[    0.937823] ACPI: PCI Interrupt Link [LAUD] (IRQs 20 21 22 23) *0, disabled.
[    0.945099] ACPI: PCI Interrupt Link [LMOD] (IRQs 20 21 22 23) *0, disabled.
[    0.952375] ACPI: PCI Interrupt Link [LPA0] (IRQs 20 21 22 23) *0, disabled.
[    0.959632] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 *21 22 23)
[    0.965734] ACPI: PCI Interrupt Link [LSA1] (IRQs *20 21 22 23)
[    0.971839] ACPI: PCI Interrupt Link [LEMA] (IRQs 20 21 22 23) *0, disabled.
[    0.979102] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *0, disabled.
[    0.986369] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *0, disabled.
[    0.993639] ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    1.002140] ACPI: PCI Interrupt Link [LNIA] (IRQs 16) *0, disabled.
[    1.008567] ACPI: PCI Interrupt Link [LNIB] (IRQs 17) *0, disabled.
[    1.014997] ACPI: PCI Interrupt Link [LNIC] (IRQs 18) *0, disabled.
[    1.021434] ACPI: PCI Interrupt Link [LNND] (IRQs 19) *0, disabled.
[    1.028166] ACPI: Enabled 1 GPEs in block 00 to 1F
[    1.033231] vgaarb: setting as boot device: PCI:0000:01:04.0
[    1.038894] vgaarb: device added: PCI:0000:01:04.0,decodes=io+mem,owns=io+mem,locks=none
[    1.046981] vgaarb: loaded
[    1.049688] vgaarb: bridge control possible 0000:01:04.0
[    1.055148] PCI: Using ACPI for IRQ routing
[    1.059334] PCI: pci_cache_line_size set to 64 bytes
[    1.059388] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    1.059392] e820: reserve RAM buffer [mem 0xbff9a000-0xbfffffff]
[    1.059686] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    1.066732] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    1.071762] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    1.079808] Switched to clocksource hpet
[    1.095357] pnp: PnP ACPI init
[    1.098460] ACPI: bus type PNP registered
[    1.102970] pnp 00:00: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    1.103057] pnp 00:01: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[    1.103137] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.103209] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[    1.103246] pnp 00:04: [dma 2]
[    1.103280] pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
[    1.103311] pnp: PnP ACPI: found 5 devices
[    1.107408] ACPI: bus type PNP unregistered
[    1.118567] pci 0000:02:00.0: can't claim BAR 6 [mem 0x68400000-0x6840ffff pref]: no compatible bridge window
[    1.128510] pci 0000:00:09.0: PCI bridge to [bus 01]
[    1.133479] pci 0000:00:09.0:   bridge window [io  0x1000-0x1fff]
[    1.139568] pci 0000:00:09.0:   bridge window [mem 0xfc000000-0xfc0fffff]
[    1.146353] pci 0000:00:09.0:   bridge window [mem 0xf8000000-0xfbffffff pref]
[    1.153577] pci 0000:02:00.0: BAR 6: assigned [mem 0xfc110000-0xfc11ffff pref]
[    1.160802] pci 0000:00:0b.0: PCI bridge to [bus 02]
[    1.165767] pci 0000:00:0b.0:   bridge window [mem 0xfc100000-0xfc1fffff]
[    1.172551] pci 0000:00:0c.0: PCI bridge to [bus 03]
[    1.177514] pci 0000:00:0c.0:   bridge window [mem 0xfc200000-0xfc2fffff]
[    1.184300] pci 0000:00:0d.0: PCI bridge to [bus 04]
[    1.189266] pci 0000:00:0e.0: PCI bridge to [bus 05]
[    1.194231] pci_bus 0000:00: resource 4 [io  0x0d00-0x3fff]
[    1.194234] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[    1.194236] pci_bus 0000:00: resource 6 [mem 0xf8000000-0xfbffffff]
[    1.194239] pci_bus 0000:00: resource 7 [mem 0xfc000000-0xfc3fffff]
[    1.194241] pci_bus 0000:00: resource 8 [io  0x0000-0x0cf7]
[    1.194244] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]
[    1.194246] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfc0fffff]
[    1.194249] pci_bus 0000:01: resource 2 [mem 0xf8000000-0xfbffffff pref]
[    1.194252] pci_bus 0000:02: resource 1 [mem 0xfc100000-0xfc1fffff]
[    1.194255] pci_bus 0000:03: resource 1 [mem 0xfc200000-0xfc2fffff]
[    1.194334] NET: Registered protocol family 2
[    1.199072] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    1.206709] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    1.214040] TCP: Hash tables configured (established 65536 bind 65536)
[    1.220638] TCP: reno registered
[    1.223888] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    1.230098] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    1.236830] NET: Registered protocol family 1
[    1.241568] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[    1.247633] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[    1.253524] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.259041] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.264528] pci 0000:00:0b.0: Found disabled HT MSI Mapping
[    1.270109] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.275631] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.281117] pci 0000:00:0c.0: Found disabled HT MSI Mapping
[    1.286690] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.292226] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.297717] pci 0000:00:0d.0: Found disabled HT MSI Mapping
[    1.303292] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.308823] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.314306] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[    1.319882] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    1.325398] pci 0000:01:04.0: Video device with shadowed ROM
[    1.325408] PCI: CLS 64 bytes, default 64
[    1.325508] Unpacking initramfs...
[    1.703506] Freeing initrd memory: 14028K (ffff88007f24c000 - ffff88007ffff000)
[    1.711360] PCI-DMA: Disabling AGP.
[    1.715009] PCI-DMA: aperture base @ b4000000 size 65536 KB
[    1.720585] PCI-DMA: using GART IOMMU.
[    1.724346] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    1.736179] platform rtc_cmos: registered platform RTC device (no PNP device found)
[    1.743995] microcode: CPU0: patch_level=0x01000084
[    1.748886] microcode: CPU1: patch_level=0x01000084
[    1.753883] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.762674] LVT offset 1 assigned for vector 0x400
[    1.767476] IBS: LVT offset 1 assigned
[    1.771247] perf: AMD IBS detected (0x00000007)
[    1.776235] futex hash table entries: 512 (order: 3, 32768 bytes)
[    1.782385] audit: initializing netlink subsys (disabled)
[    1.787815] audit: type=2000 audit(1490778958.532:1): initialized
[    1.794661] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.801061] zbud: loaded
[    1.803867] VFS: Disk quotas dquot_6.5.2
[    1.807815] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.814342] msgmni has been set to 9946
[    1.818698] alg: No test for stdrng (krng)
[    1.822852] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.830316] io scheduler noop registered
[    1.834242] io scheduler deadline registered
[    1.838564] io scheduler cfq registered (default)
[    1.843462] pcieport 0000:00:0b.0: irq 40 for MSI/MSI-X
[    1.843598] pcieport 0000:00:0c.0: irq 41 for MSI/MSI-X
[    1.843710] pcieport 0000:00:0d.0: irq 42 for MSI/MSI-X
[    1.843816] pcieport 0000:00:0e.0: irq 43 for MSI/MSI-X
[    1.843969] aer 0000:00:0b.0:pcie02: service driver aer loaded
[    1.843996] aer 0000:00:0c.0:pcie02: service driver aer loaded
[    1.844021] aer 0000:00:0d.0:pcie02: service driver aer loaded
[    1.844044] aer 0000:00:0e.0:pcie02: service driver aer loaded
[    1.844066] pcieport 0000:00:0b.0: Signaling PME through PCIe PME interrupt
[    1.851029] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[    1.857556] pcie_pme 0000:00:0b.0:pcie01: service driver pcie_pme loaded
[    1.857569] pcieport 0000:00:0c.0: Signaling PME through PCIe PME interrupt
[    1.864529] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[    1.871051] pcie_pme 0000:00:0c.0:pcie01: service driver pcie_pme loaded
[    1.871062] pcieport 0000:00:0d.0: Signaling PME through PCIe PME interrupt
[    1.878018] pcie_pme 0000:00:0d.0:pcie01: service driver pcie_pme loaded
[    1.878028] pcieport 0000:00:0e.0: Signaling PME through PCIe PME interrupt
[    1.884980] pcie_pme 0000:00:0e.0:pcie01: service driver pcie_pme loaded
[    1.885011] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.890605] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.897310] GHES: HEST is not enabled!
[    1.901201] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.927787] 00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.955427] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[    1.963292] Linux agpgart interface v0.103
[    1.967550] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f03:MOU] at 0x60,0x64 irq 1,12
[    1.977697] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.982670] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.987911] mousedev: PS/2 mouse device common for all mice
[    1.993588] rtc_cmos rtc_cmos: RTC can wake from S4
[    1.998641] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[    2.005033] rtc_cmos rtc_cmos: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    2.012894] ledtrig-cpu: registered to indicate activity on CPUs
[    2.019077] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[    2.025518] AMD IOMMUv2 functionality not available on this system
[    2.031851] TCP: cubic registered
[    2.035228] NET: Registered protocol family 10
[    2.040055] mip6: Mobile IPv6
[    2.043020] NET: Registered protocol family 17
[    2.047554] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    2.056191] mpls_gso: MPLS GSO support
[    2.060431] registered taskstats version 1
[    2.065277] rtc_cmos rtc_cmos: setting system clock to 2017-03-29 09:16:00 UTC (1490778960)
[    2.073697] PM: Hibernation image not present or could not be loaded.
[    2.075629] Freeing unused kernel memory: 1204K (ffffffff818ee000 - ffffffff81a1b000)
[    2.083464] Write protecting the kernel read-only data: 8192k
[    2.092665] Freeing unused kernel memory: 924K (ffff880001519000 - ffff880001600000)
[    2.101226] Freeing unused kernel memory: 216K (ffff8800017ca000 - ffff880001800000)
[    2.132265] systemd-udevd[63]: starting version 215
[    2.137992] random: systemd-udevd urandom read with 3 bits of entropy available
[    2.176383] SCSI subsystem initialized
[    2.182844] ACPI: bus type USB registered
[    2.188649] FDC 0 is a post-1991 82077
[    2.193200] pps_core: LinuxPPS API ver. 1 registered
[    2.195285] usbcore: registered new interface driver usbfs
[    2.195301] usbcore: registered new interface driver hub
[    2.195361] libata version 3.00 loaded.
[    2.209009] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.218731] pata_amd 0000:00:06.0: version 0.4.1
[    2.220949] PTP clock support registered
[    2.230794] usbcore: registered new device driver usb
[    2.236194] tg3.c:v3.137 (May 11, 2014)
[    2.240064] tg3 0000:02:00.0: enabling device (0004 -> 0006)
[    2.246691] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.247073] scsi0 : pata_amd
[    2.256303] ACPI: PCI Interrupt Link [LNIB] enabled at IRQ 17
[    2.266438] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.272069] scsi1 : pata_amd
[    2.272170] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x3020 irq 14
[    2.272172] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x3028 irq 15
[    2.289469] sata_nv 0000:00:07.0: version 3.5
[    2.289758] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
[    2.289839] ehci-pci: EHCI PCI platform driver
[    2.319373] scsi2 : sata_nv
[    2.322476] scsi3 : sata_nv
[    2.325396] ata3: SATA max UDMA/133 cmd 0x3050 ctl 0x3070 bmdma 0x3030 irq 21
[    2.332534] ata4: SATA max UDMA/133 cmd 0x3058 ctl 0x3074 bmdma 0x3038 irq 21
[    2.337039] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM95721) rev 4201] (PCI Express) MAC address 00:1e:8c:51:61:a2
[    2.337042] tg3 0000:02:00.0 eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    2.337044] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.337046] tg3 0000:02:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.374175] tg3 0000:03:00.0: enabling device (0004 -> 0006)
[    2.380001] ACPI: PCI Interrupt Link [LNIA] enabled at IRQ 16
[    2.386062] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 20
[    2.392250] scsi4 : sata_nv
[    2.395174] scsi5 : sata_nv
[    2.398047] ata5: SATA max UDMA/133 cmd 0x3060 ctl 0x3078 bmdma 0x3040 irq 20
[    2.405175] ata6: SATA max UDMA/133 cmd 0x3068 ctl 0x307c bmdma 0x3048 irq 20
[    2.413548] ehci-pci 0000:00:02.1: EHCI Host Controller
[    2.419478] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 1
[    2.426888] ehci-pci 0000:00:02.1: debug port 1
[    2.431564] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[    2.431606] ehci-pci 0000:00:02.1: irq 22, io mem 0xfc303000
[    2.444482] tg3 0000:03:00.0 eth1: Tigon3 [partno(BCM95721) rev 4201] (PCI Express) MAC address 00:1e:8c:51:63:95
[    2.454736] tg3 0000:03:00.0 eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    2.464471] tg3 0000:03:00.0 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.472289] tg3 0000:03:00.0 eth1: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.479041] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    2.485037] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.491837] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.499054] usb usb1: Product: EHCI Host Controller
[    2.503929] usb usb1: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    2.510020] usb usb1: SerialNumber: 0000:00:02.1
[    2.514878] hub 1-0:1.0: USB hub found
[    2.518640] hub 1-0:1.0: 10 ports detected
[    2.523865] ohci-pci: OHCI PCI platform driver
[    2.529923] ohci-pci 0000:00:02.0: OHCI PCI host controller
[    2.535510] ohci-pci 0000:00:02.0: new USB bus registered, assigned bus number 2
[    2.542946] ohci-pci 0000:00:02.0: irq 23, io mem 0xfc300000
[    2.605327] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.612116] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.619332] usb usb2: Product: OHCI PCI host controller
[    2.624555] usb usb2: Manufacturer: Linux 3.16.0-4-amd64 ohci_hcd
[    2.630645] usb usb2: SerialNumber: 0000:00:02.0
[    2.635459] hub 2-0:1.0: USB hub found
[    2.639216] hub 2-0:1.0: 10 ports detected
[    2.691275] ata3: SATA link down (SStatus 0 SControl 300)
[    2.719253] ata5: SATA link down (SStatus 0 SControl 300)
[    2.735254] tsc: Refined TSC clocksource calibration: 1909.786 MHz
[    3.007153] ata4: SATA link down (SStatus 0 SControl 300)
[    3.323042] ata6: SATA link down (SStatus 0 SControl 300)
[    3.346520] FS-Cache: Loaded
[    3.354593] RPC: Registered named UNIX socket transport module.
[    3.361859] RPC: Registered udp transport module.
[    3.367943] RPC: Registered tcp transport module.
[    3.374032] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    3.387166] FS-Cache: Netfs 'nfs' registered for caching
[    3.403687] tg3 0000:02:00.0: irq 44 for MSI/MSI-X
[    3.451052] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    3.738984] Switched to clocksource tsc
[    6.577887] tg3 0000:02:00.0 eth0: Link is up at 1000 Mbps, full duplex
[    6.584498] tg3 0000:02:00.0 eth0: Flow control is on for TX and on for RX
[    6.591388] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.588891] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    7.602413] systemd[1]: Detected architecture 'x86-64'.
[    7.650051] systemd[1]: Inserted module 'autofs4'
[    7.656212] systemd[1]: Set hostname to <cb-test-tgt>.
[    7.805812] systemd[1]: Cannot add dependency job for unit dbus.socket, ignoring: Unit dbus.socket failed to load: No such file or directory.
[    7.818528] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    7.833902] systemd[1]: Expecting device dev-ttyS0.device...
[    7.849631] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    7.857434] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    7.865046] systemd[1]: Starting Remote File Systems (Pre).
[    7.881503] systemd[1]: Reached target Remote File Systems (Pre).
[    7.887641] systemd[1]: Starting Encrypted Volumes.
[    7.901489] systemd[1]: Reached target Encrypted Volumes.
[    7.906944] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    7.929488] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    7.938909] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[    7.946960] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    7.954890] systemd[1]: Starting Paths.
[    7.969467] systemd[1]: Reached target Paths.
[    7.973857] systemd[1]: Starting Swap.
[    7.985462] systemd[1]: Reached target Swap.
[    7.989749] systemd[1]: Starting Root Slice.
[    8.001459] systemd[1]: Created slice Root Slice.
[    8.006189] systemd[1]: Starting User and Session Slice.
[    8.021451] systemd[1]: Created slice User and Session Slice.
[    8.027216] systemd[1]: Starting Delayed Shutdown Socket.
[    8.041446] systemd[1]: Listening on Delayed Shutdown Socket.
[    8.047208] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[    8.065438] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    8.072411] systemd[1]: Starting Journal Socket (/dev/log).
[    8.089429] systemd[1]: Listening on Journal Socket (/dev/log).
[    8.095378] systemd[1]: Starting udev Kernel Socket.
[    8.109417] systemd[1]: Listening on udev Kernel Socket.
[    8.114755] systemd[1]: Starting udev Control Socket.
[    8.129413] systemd[1]: Listening on udev Control Socket.
[    8.134845] systemd[1]: Starting Journal Socket.
[    8.149404] systemd[1]: Listening on Journal Socket.
[    8.154404] systemd[1]: Starting System Slice.
[    8.169399] systemd[1]: Created slice System Slice.
[    8.174295] systemd[1]: Starting system-getty.slice.
[    8.189398] systemd[1]: Created slice system-getty.slice.
[    8.194808] systemd[1]: Starting system-serial\x2dgetty.slice.
[    8.209387] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    8.215696] systemd[1]: Starting Increase datagram queue length...
[    8.234206] systemd[1]: Starting udev Coldplug all Devices...
[    8.264392] systemd[1]: Starting Load Kernel Modules...
[    8.281415] systemd[1]: Started Set Up Additional Binary Formats.
[    8.287706] systemd[1]: Mounting Debug File System...
[    8.302659] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    8.326432] systemd[1]: Mounting POSIX Message Queue File System...
[    8.342140] systemd[1]: Mounting Huge Pages File System...
[    8.358039] systemd[1]: Starting Slices.
[    8.369344] systemd[1]: Reached target Slices.
[    8.373839] systemd[1]: Starting Remount Root and Kernel File Systems...
[    8.401411] systemd[1]: Mounted Huge Pages File System.
[    8.417321] systemd[1]: Mounted POSIX Message Queue File System.
[    8.433317] systemd[1]: Mounted Debug File System.
[    8.449337] systemd[1]: Started Increase datagram queue length.
[    8.465409] systemd[1]: Started Load Kernel Modules.
[    8.485394] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    8.505302] systemd[1]: Started Remount Root and Kernel File Systems.
[    8.521295] systemd[1]: Started udev Coldplug all Devices.
[    8.567931] systemd[1]: Started Various fixups to make systemd work better on Debian.
[    8.575802] systemd[1]: Starting Load/Save Random Seed...
[    8.590639] systemd[1]: Starting Create Static Device Nodes in /dev...
[    8.606120] systemd[1]: Starting Apply Kernel Variables...
[    8.622192] systemd[1]: Mounted Configuration File System.
[    8.627958] systemd[1]: Mounted FUSE Control File System.
[    8.633489] systemd[1]: Starting Syslog Socket.
[    8.649340] systemd[1]: Listening on Syslog Socket.
[    8.654349] systemd[1]: Starting Sockets.
[    8.669297] systemd[1]: Reached target Sockets.
[    8.673898] systemd[1]: Starting Journal Service...
[    8.697303] systemd[1]: Started Journal Service.
[    8.772607] systemd-udevd[161]: starting version 215
[    8.897802] systemd-journald[160]: Received request to flush runtime journal from PID 1
[    8.940120] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.951019] i2c i2c-0: nForce2 SMBus adapter at 0x2c80
[    8.959521] i2c i2c-1: nForce2 SMBus adapter at 0x2cc0
[    8.967097] acpi-cpufreq: overriding BIOS provided _PSD data
[    8.974661] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    8.989939] ACPI: Power Button [PWRB]
[    8.999885] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    9.021086] ACPI: Power Button [PWRF]
[    9.026351] k10temp 0000:00:18.3: unreliable CPU thermal sensor; monitoring disabled
[    9.049450] k10temp 0000:00:19.3: unreliable CPU thermal sensor; monitoring disabled
[    9.059525] input: PC Speaker as /devices/platform/pcspkr/input/input4
[    9.070427] EDAC MC: Ver: 3.0.0
[    9.084707] MCE: In-kernel MCE decoding enabled.
[    9.094967] AMD64 EDAC driver v3.4.0
[    9.100774] EDAC amd64: DRAM ECC enabled.
[    9.112597] EDAC amd64: F10h detected (node 0).
[    9.113215] kvm: Nested Virtualization enabled
[    9.113218] kvm: Nested Paging enabled
[    9.125358] EDAC MC: DCT0 chip selects:
[    9.125360] EDAC amd64: MC: 0:     0MB 1:     0MB
[    9.130106] EDAC amd64: MC: 2:     0MB 3:     0MB
[    9.134814] EDAC amd64: MC: 4:     0MB 5:     0MB
[    9.139551] EDAC amd64: MC: 6:  2048MB 7:  2048MB
[    9.144254] EDAC MC: DCT1 chip selects:
[    9.144257] EDAC amd64: MC: 0:     0MB 1:     0MB
[    9.149125] EDAC amd64: MC: 2:     0MB 3:     0MB
[    9.153841] EDAC amd64: MC: 4:     0MB 5:     0MB
[    9.158561] EDAC amd64: MC: 6:  1024MB 7:  1024MB
[    9.163271] EDAC amd64: using x4 syndromes.
[    9.170689] EDAC amd64: CS6: Registered DDR2 RAM
[    9.176515] EDAC amd64: CS7: Registered DDR2 RAM
[    9.186972] EDAC MC0: Giving out device to module amd64_edac controller F10h: DEV 0000:00:18.2 (INTERRUPT)
[    9.199331] EDAC amd64: DRAM ECC enabled.
[    9.204087] EDAC amd64: F10h detected (node 1).
[    9.208667] EDAC MC: DCT0 chip selects:
[    9.208670] EDAC amd64: MC: 0:  1024MB 1:     0MB
[    9.213382] EDAC amd64: MC: 2:     0MB 3:     0MB
[    9.218091] EDAC amd64: MC: 4:     0MB 5:     0MB
[    9.222799] EDAC amd64: MC: 6:     0MB 7:     0MB
[    9.227503] EDAC MC: DCT1 chip selects:
[    9.227505] EDAC amd64: MC: 0:     0MB 1:     0MB
[    9.232207] EDAC amd64: MC: 2:     0MB 3:     0MB
[    9.236912] EDAC amd64: MC: 4:     0MB 5:     0MB
[    9.241615] EDAC amd64: MC: 6:     0MB 7:     0MB
[    9.246320] EDAC amd64: using x4 syndromes.
[    9.250507] EDAC amd64: MCT channel count: 1
[    9.254896] EDAC amd64: CS0: Registered DDR2 RAM
[    9.259687] EDAC MC1: Giving out device to module amd64_edac controller F10h: DEV 0000:00:19.2 (INTERRUPT)
[    9.269465] EDAC PCI0: Giving out device to module amd64_edac controller EDAC PCI controller: DEV 0000:00:18.2 (POLLED)
[    9.357701] random: nonblocking pool is initialized
[   39.494117] *****RAPTOR ENGINEERING AUTOMATED TEST BOOT SUCCESS*****