[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.36-1+deb8u1 (2016-09-03)
[    0.000000] Command line: BOOT_IMAGE=/live/vmlinuz boot=live components quiet splash initrd=/live/initrd.img
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bff97fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bff98000-0x00000000dfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041effffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: ASUS F2A85-M/F2A85-M, BIOS 4.5-771-gf3e2679-dirty 01/06/2017
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] AGP: No AGP bridge found
[    0.000000] e820: last_pfn = 0x41f000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-back
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000C0000000 mask FFFFE0000000 write-back
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 base 0000FF800000 mask FFFFFF800000 write-protect
[    0.000000]   7 disabled
[    0.000000] TOM2: 000000041f000000 aka 16880M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0xbff98 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f6ee0-0x000f6eef] mapped at [ffff8800000f6ee0]
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01af4000, 0x01af4fff] PGTABLE
[    0.000000] BRK [0x01af5000, 0x01af5fff] PGTABLE
[    0.000000] BRK [0x01af6000, 0x01af6fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x41ee00000-0x41effffff]
[    0.000000]  [mem 0x41ee00000-0x41effffff] page 2M
[    0.000000] BRK [0x01af7000, 0x01af7fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x41c000000-0x41edfffff]
[    0.000000]  [mem 0x41c000000-0x41edfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x400000000-0x41bffffff]
[    0.000000]  [mem 0x400000000-0x41bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0xbff97fff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x3fffffff] page 2M
[    0.000000]  [mem 0x40000000-0x7fffffff] page 1G
[    0.000000]  [mem 0x80000000-0xbfdfffff] page 2M
[    0.000000]  [mem 0xbfe00000-0xbff97fff] page 4k
[    0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
[    0.000000]  [mem 0x100000000-0x3ffffffff] page 1G
[    0.000000] RAMDISK: [mem 0x7e53a000-0x7fffffff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F70F0 000024 (v02 CORE  )
[    0.000000] ACPI: XSDT 0x00000000BFFAF0E0 00006C (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: FACP 0x00000000BFFB0B10 0000F4 (v04 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: DSDT 0x00000000BFFAF280 00188F (v02 ASUS   COREBOOT 00010001 INTL 20160831)
[    0.000000] ACPI: FACS 0x00000000BFFAF240 000040
[    0.000000] ACPI: FACS 0x00000000BFFAF240 000040
[    0.000000] ACPI: SSDT 0x00000000BFFB0C10 00008A (v02 CORE   COREBOOT 0000002A CORE 0000002A)
[    0.000000] ACPI: TCPA 0x00000000BFFB0CA0 000032 (v02 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: APIC 0x00000000BFFB0CE0 000072 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: HPET 0x00000000BFFB0D60 000038 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: HEST 0x00000000BFFB0DA0 0001D0 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: IVRS 0x00000000BFFB0F70 000070 (v02 AMD    AMDIOMMU 00000001 AMD  00000000)
[    0.000000] ACPI: SSDT 0x00000000BFFB0FE0 00051F (v02 AMD    ALIB     00000001 MSFT 04000000)
[    0.000000] ACPI: SSDT 0x00000000BFFB1500 000B9C (v01 AMD    POWERNOW 00000001 AMD  00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000041effffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x41effffff]
[    0.000000]   NODE_DATA [mem 0x41eff9000-0x41effdfff]
[    0.000000]  [ffffea0000000000-ffffea000e7fffff] PMD -> [ffff88040ee00000-ffff88041c7fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x41effffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0xbff97fff]
[    0.000000]   node   0: [mem 0x100000000-0x41effffff]
[    0.000000] On node 0 totalpages: 4058934
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10695 pages used for memmap
[    0.000000]   DMA32 zone: 782232 pages, LIFO batch:31
[    0.000000]   Normal zone: 44744 pages used for memmap
[    0.000000]   Normal zone: 3272704 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x818
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x10] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x11] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x12] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x13] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10228210 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xbff98000-0xdfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xffffffff]
[    0.000000] e820: [mem 0xe0000000-0xf7ffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88041ec00000 s80960 r8192 d21440 u524288
[    0.000000] pcpu-alloc: s80960 r8192 d21440 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 4003418
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/live/vmlinuz boot=live components quiet splash initrd=/live/initrd.img
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] AGP: Node 0: aperture [bus addr 0x00000000-0x01ffffff] (32MB)
[    0.000000] AGP: Your BIOS doesn't leave a aperture memory hole
[    0.000000] AGP: Please enable the IOMMU option in the BIOS setup
[    0.000000] AGP: This costs you 64MB of RAM
[    0.000000] AGP: Mapping aperture over RAM [mem 0xb4000000-0xb7ffffff] (65536KB)
[    0.000000] PM: Registered nosave memory: [mem 0xb4000000-0xb7ffffff]
[    0.000000] Memory: 15841464K/16235736K available (5237K kernel code, 947K rwdata, 1836K rodata, 1204K init, 840K bss, 394272K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS:33024 nr_irqs:712 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 3693.440 MHz processor
[    0.000022] Calibrating delay loop (skipped), value calculated using timer frequency.. 7386.88 BogoMIPS (lpj=14773760)
[    0.000024] pid_max: default: 32768 minimum: 301
[    0.000032] ACPI: Core revision 20140424
[    0.001433] ACPI: All ACPI Tables successfully acquired
[    0.001459] Security Framework initialized
[    0.001469] AppArmor: AppArmor disabled by boot time parameter
[    0.001471] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.002454] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.003033] spurious 8259A interrupt: IRQ7.
[    0.006623] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.008490] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.008509] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.008823] Initializing cgroup subsys memory
[    0.008829] Initializing cgroup subsys devices
[    0.008836] Initializing cgroup subsys freezer
[    0.008839] Initializing cgroup subsys net_cls
[    0.008843] Initializing cgroup subsys blkio
[    0.008847] Initializing cgroup subsys perf_event
[    0.008849] Initializing cgroup subsys net_prio
[    0.008871] tseg: 0000000000
[    0.008876] CPU: Physical Processor ID: 0
[    0.008877] CPU: Processor Core ID: 0
[    0.008879] mce: CPU supports 7 MCE banks
[    0.008890] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0
tlb_flushall_shift: 6
[    0.008959] Freeing SMP alternatives memory: 20K (ffffffff81a1b000 - ffffffff81a20000)
[    0.009699] ftrace: allocating 21697 entries in 85 pages
[    0.101079] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.140729] smpboot: CPU0: AMD A10-6700 APU with Radeon(tm) HD Graphics (fam: 15, model: 13, stepping: 01)
[    0.246814] Performance Events: Fam15h core perfctr, AMD PMU driver.
[    0.246818] ... version:                0
[    0.246819] ... bit width:              48
[    0.246820] ... generic registers:      6
[    0.246821] ... value mask:             0000ffffffffffff
[    0.246822] ... max period:             00007fffffffffff
[    0.246823] ... fixed-purpose events:   0
[    0.246824] ... event mask:             000000000000003f
[    0.248199] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.248307] x86: Booting SMP configuration:
[    0.248308] .... node  #0, CPUs:      #1 #2 #3
[    0.287596] x86: Booted up 1 node, 4 CPUs
[    0.287599] smpboot: Total of 4 processors activated (29547.52 BogoMIPS)
[    0.288359] devtmpfs: initialized
[    0.294022] pinctrl core: initialized pinctrl subsystem
[    0.294110] NET: Registered protocol family 16
[    0.294232] cpuidle: using governor ladder
[    0.294235] cpuidle: using governor menu
[    0.294287] ACPI: bus type PCI registered
[    0.294289] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.294376] PCI: Using configuration type 1 for base access
[    0.294377] PCI: Using configuration type 1 for extended access
[    0.307409] ACPI: Added _OSI(Module Device)
[    0.307411] ACPI: Added _OSI(Processor Device)
[    0.307413] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.307414] ACPI: Added _OSI(Processor Aggregator Device)
[    0.308322] ACPI: Executed 2 blocks of module-level executable AML code
[    0.310571] ACPI: Interpreter enabled
[    0.310593] ACPI: (supports S0 S1 S2 S3 S4 S5)
[    0.310594] ACPI: Using IOAPIC for interrupt routing
[    0.310608] HEST: Table parsing has been initialized.
[    0.310611] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.313013] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.313018] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.313100] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.313173] acpi PNP0A03:00: host bridge window expanded to [io  0x0000-0x0cf7]; [io  0x0000-0x0cf7] ignored
[    0.313366] PCI host bridge to bus 0000:00
[    0.313369] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.313371] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.313373] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.313374] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.313376] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[    0.313377] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xffffffff]
[    0.313384] pci 0000:00:00.0: [1022:1410] type 00 class 0x060000
[    0.313476] pci 0000:00:00.2: [1022:1419] type 00 class 0x080600
[    0.313586] pci 0000:00:02.0: [1022:1412] type 01 class 0x060400
[    0.313627] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[    0.313673] pci 0000:00:02.0: System wakeup disabled by ACPI
[    0.313728] pci 0000:00:11.0: [1022:7801] type 00 class 0x010601
[    0.313742] pci 0000:00:11.0: reg 0x10: [io  0x3010-0x3017]
[    0.313750] pci 0000:00:11.0: reg 0x14: [io  0x3020-0x3023]
[    0.313758] pci 0000:00:11.0: reg 0x18: [io  0x3018-0x301f]
[    0.313766] pci 0000:00:11.0: reg 0x1c: [io  0x3024-0x3027]
[    0.313773] pci 0000:00:11.0: reg 0x20: [io  0x3000-0x300f]
[    0.313781] pci 0000:00:11.0: reg 0x24: [mem 0xf3288000-0xf32887ff]
[    0.313878] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
[    0.313889] pci 0000:00:12.0: reg 0x10: [mem 0xf3284000-0xf3284fff]
[    0.313972] pci 0000:00:12.0: System wakeup disabled by ACPI
[    0.314016] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
[    0.314032] pci 0000:00:12.2: reg 0x10: [mem 0xf3289000-0xf32890ff]
[    0.314098] pci 0000:00:12.2: supports D1 D2
[    0.314100] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.314144] pci 0000:00:12.2: System wakeup disabled by ACPI
[    0.314188] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
[    0.314199] pci 0000:00:13.0: reg 0x10: [mem 0xf3285000-0xf3285fff]
[    0.314282] pci 0000:00:13.0: System wakeup disabled by ACPI
[    0.314327] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
[    0.314343] pci 0000:00:13.2: reg 0x10: [mem 0xf328a000-0xf328a0ff]
[    0.314409] pci 0000:00:13.2: supports D1 D2
[    0.314410] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[    0.314457] pci 0000:00:13.2: System wakeup disabled by ACPI
[    0.314501] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[    0.314624] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[    0.314641] pci 0000:00:14.2: reg 0x10: [mem 0xf3280000-0xf3283fff 64bit]
[    0.314694] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.314777] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[    0.314898] pci 0000:00:14.4: [1022:780f] type 01 class 0x060401
[    0.314957] pci 0000:00:14.4: System wakeup disabled by ACPI
[    0.314997] pci 0000:00:14.5: [1022:7809] type 00 class 0x0c0310
[    0.315008] pci 0000:00:14.5: reg 0x10: [mem 0xf3286000-0xf3286fff]
[    0.315090] pci 0000:00:14.5: System wakeup disabled by ACPI
[    0.315135] pci 0000:00:15.0: [1022:43a0] type 01 class 0x060400
[    0.315193] pci 0000:00:15.0: supports D1 D2
[    0.315240] pci 0000:00:15.0: System wakeup disabled by ACPI
[    0.315283] pci 0000:00:15.1: [1022:43a1] type 01 class 0x060400
[    0.315344] pci 0000:00:15.1: supports D1 D2
[    0.315391] pci 0000:00:15.1: System wakeup disabled by ACPI
[    0.315435] pci 0000:00:16.0: [1022:7807] type 00 class 0x0c0310
[    0.315446] pci 0000:00:16.0: reg 0x10: [mem 0xf3287000-0xf3287fff]
[    0.315529] pci 0000:00:16.0: System wakeup disabled by ACPI
[    0.315574] pci 0000:00:16.2: [1022:7808] type 00 class 0x0c0320
[    0.315591] pci 0000:00:16.2: reg 0x10: [mem 0xf328b000-0xf328b0ff]
[    0.315657] pci 0000:00:16.2: supports D1 D2
[    0.315658] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[    0.315703] pci 0000:00:16.2: System wakeup disabled by ACPI
[    0.315745] pci 0000:00:18.0: [1022:1400] type 00 class 0x060000
[    0.315820] pci 0000:00:18.1: [1022:1401] type 00 class 0x060000
[    0.315892] pci 0000:00:18.2: [1022:1402] type 00 class 0x060000
[    0.315967] pci 0000:00:18.3: [1022:1403] type 00 class 0x060000
[    0.316044] pci 0000:00:18.4: [1022:1404] type 00 class 0x060000
[    0.316116] pci 0000:00:18.5: [1022:1405] type 00 class 0x060000
[    0.316246] pci 0000:01:00.0: [10de:1380] type 00 class 0x030000
[    0.316258] pci 0000:01:00.0: reg 0x10: [mem 0xf2000000-0xf2ffffff]
[    0.316270] pci 0000:01:00.0: reg 0x14: [mem 0xe0000000-0xefffffff 64bit pref]
[    0.316282] pci 0000:01:00.0: reg 0x1c: [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.316290] pci 0000:01:00.0: reg 0x24: [io  0x1000-0x107f]
[    0.316298] pci 0000:01:00.0: reg 0x30: [mem 0xf3000000-0xf307ffff pref]
[    0.316408] pci 0000:01:00.1: [10de:0fbc] type 00 class 0x040300
[    0.316420] pci 0000:01:00.1: reg 0x10: [mem 0xf3080000-0xf3083fff]
[    0.326529] pci 0000:00:02.0: PCI bridge to [bus 01]
[    0.326536] pci 0000:00:02.0:   bridge window [io  0x1000-0x1fff]
[    0.326539] pci 0000:00:02.0:   bridge window [mem 0xf2000000-0xf30fffff]
[    0.326542] pci 0000:00:02.0:   bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[    0.326637] pci 0000:00:14.4: PCI bridge to [bus 02] (subtractive decode)
[    0.326645] pci 0000:00:14.4:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.326647] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.326649] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.326651] pci 0000:00:14.4:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.326652] pci 0000:00:14.4:   bridge window [mem 0xe0000000-0xffffffff] (subtractive decode)
[    0.326707] pci 0000:00:15.0: PCI bridge to [bus 03]
[    0.326793] pci 0000:04:00.0: [10ec:8168] type 00 class 0x020000
[    0.326814] pci 0000:04:00.0: reg 0x10: [io  0x2000-0x20ff]
[    0.326841] pci 0000:04:00.0: reg 0x18: [mem 0xf3104000-0xf3104fff 64bit pref]
[    0.326858] pci 0000:04:00.0: reg 0x20: [mem 0xf3100000-0xf3103fff 64bit pref]
[    0.326951] pci 0000:04:00.0: supports D1 D2
[    0.326953] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.338515] pci 0000:00:15.1: PCI bridge to [bus 04]
[    0.338523] pci 0000:00:15.1:   bridge window [io  0x2000-0x2fff]
[    0.338530] pci 0000:00:15.1:   bridge window [mem 0xf3100000-0xf31fffff 64bit pref]
[    0.338804] ACPI: PCI Interrupt Link [INTA] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.338851] ACPI: PCI Interrupt Link [INTB] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.338896] ACPI: PCI Interrupt Link [INTC] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.338941] ACPI: PCI Interrupt Link [INTD] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.338984] ACPI: PCI Interrupt Link [INTE] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.339028] ACPI: PCI Interrupt Link [INTF] (IRQs 9) *0
[    0.339069] ACPI: PCI Interrupt Link [INTG] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.339112] ACPI: PCI Interrupt Link [INTH] (IRQs 3 4 5 7 10 11 12 15) *0
[    0.339200] ACPI: Enabled 5 GPEs in block 00 to 1F
[    0.339325] vgaarb: setting as boot device: PCI:0000:01:00.0
[    0.339327] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.339329] vgaarb: loaded
[    0.339330] vgaarb: bridge control possible 0000:01:00.0
[    0.339397] PCI: Using ACPI for IRQ routing
[    0.339399] PCI: pci_cache_line_size set to 64 bytes
[    0.339449] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    0.339451] e820: reserve RAM buffer [mem 0xbff98000-0xbfffffff]
[    0.339452] e820: reserve RAM buffer [mem 0x41f000000-0x41fffffff]
[    0.339595] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.339598] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[    0.341678] Switched to clocksource hpet
[    0.348230] pnp: PnP ACPI init
[    0.348242] ACPI: bus type PNP registered
[    0.348408] system 00:00: [mem 0xfec10002-0xfec11001] has been reserved
[    0.348411] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.348453] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.348571] pnp: PnP ACPI: found 2 devices
[    0.348572] ACPI: bus type PNP unregistered
[    0.355303] pci 0000:00:02.0: PCI bridge to [bus 01]
[    0.355306] pci 0000:00:02.0:   bridge window [io  0x1000-0x1fff]
[    0.355310] pci 0000:00:02.0:   bridge window [mem 0xf2000000-0xf30fffff]
[    0.355313] pci 0000:00:02.0:   bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[    0.355316] pci 0000:00:14.4: PCI bridge to [bus 02]
[    0.355325] pci 0000:00:15.0: PCI bridge to [bus 03]
[    0.355333] pci 0000:00:15.1: PCI bridge to [bus 04]
[    0.355336] pci 0000:00:15.1:   bridge window [io  0x2000-0x2fff]
[    0.355341] pci 0000:00:15.1:   bridge window [mem 0xf3100000-0xf31fffff 64bit pref]
[    0.355346] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.355347] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.355349] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.355350] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[    0.355352] pci_bus 0000:00: resource 8 [mem 0xe0000000-0xffffffff]
[    0.355354] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]
[    0.355355] pci_bus 0000:01: resource 1 [mem 0xf2000000-0xf30fffff]
[    0.355356] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xf1ffffff 64bit pref]
[    0.355358] pci_bus 0000:02: resource 4 [io  0x0000-0x0cf7]
[    0.355360] pci_bus 0000:02: resource 5 [io  0x0d00-0xffff]
[    0.355361] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff]
[    0.355363] pci_bus 0000:02: resource 7 [mem 0x000c0000-0x000dffff]
[    0.355364] pci_bus 0000:02: resource 8 [mem 0xe0000000-0xffffffff]
[    0.355366] pci_bus 0000:04: resource 0 [io  0x2000-0x2fff]
[    0.355367] pci_bus 0000:04: resource 2 [mem 0xf3100000-0xf31fffff 64bit pref]
[    0.355486] NET: Registered protocol family 2
[    0.355791] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.356099] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.356307] TCP: Hash tables configured (established 131072 bind 65536)
[    0.356341] TCP: reno registered
[    0.356363] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.356441] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.356614] NET: Registered protocol family 1
[    0.410929] pci 0000:01:00.0: Video device with shadowed ROM
[    0.410945] PCI: CLS 64 bytes, default 64
[    0.411007] Unpacking initramfs...
[    0.797549] Freeing initrd memory: 27416K (ffff88007e53a000 - ffff880080000000)
[    0.797576] AMD-Vi: Applying erratum 746 workaround for IOMMU at 0000:00:00.2
[    0.797848] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
[    0.797849] AMD-Vi:  Extended features:  PreF PPR GT IA
[    0.797852] AMD-Vi: Interrupt remapping enabled
[    0.797864] pci 0000:00:00.2: irq 40 for MSI/MSI-X
[    0.808471] AMD-Vi: Lazy IO/TLB flushing enabled
[    0.808895] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.808898] software IO TLB [mem 0xbbf98000-0xbff98000] (64MB) mapped at [ffff8800bbf98000-ffff8800bff97fff]
[    0.809120] perf: AMD NB counters detected
[    0.809183] microcode: CPU0: patch_level=0x00000000
[    0.809191] microcode: CPU1: patch_level=0x00000000
[    0.809196] microcode: CPU2: patch_level=0x00000000
[    0.809204] microcode: CPU3: patch_level=0x00000000
[    0.809281] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.809286] LVT offset 0 assigned for vector 0x400
[    0.809299] perf: AMD IBS detected (0x000000ff)
[    0.809607] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.809655] audit: initializing netlink subsys (disabled)
[    0.809676] audit: type=2000 audit(1483912766.624:1): initialized
[    0.810127] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.810151] zbud: loaded
[    0.810346] VFS: Disk quotas dquot_6.5.2
[    0.810366] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.810422] msgmni has been set to 30993
[    0.810739] alg: No test for stdrng (krng)
[    0.810768] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.810821] io scheduler noop registered
[    0.810823] io scheduler deadline registered
[    0.810863] io scheduler cfq registered (default)
[    0.810945] pcieport 0000:00:02.0: device [1022:1412] has invalid IRQ; check vendor BIOS
[    0.811065] pcieport 0000:00:02.0: irq 41 for MSI/MSI-X
[    0.811141] pcieport 0000:00:15.0: irq 42 for MSI/MSI-X
[    0.811215] pcieport 0000:00:15.1: irq 43 for MSI/MSI-X
[    0.811300] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[    0.811302] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    0.811304] pci 0000:01:00.1: Signaling PME through PCIe PME interrupt
[    0.811306] pcie_pme 0000:00:02.0:pcie01: service driver pcie_pme loaded
[    0.811321] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt
[    0.811325] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded
[    0.811339] pcieport 0000:00:15.1: Signaling PME through PCIe PME interrupt
[    0.811340] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[    0.811343] pcie_pme 0000:00:15.1:pcie01: service driver pcie_pme loaded
[    0.811360] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.811378] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.811435] GHES: Failed to enable APEI firmware first mode.
[    0.811561] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.831899] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.832239] Linux agpgart interface v0.103
[    0.832333] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    1.081158] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.081337] mousedev: PS/2 mouse device common for all mice
[    1.081378] rtc_cmos 00:01: RTC can wake from S4
[    1.081518] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    1.081548] rtc_cmos 00:01: alarms up to one day, 114 bytes nvram, hpet irqs
[    1.081572] ledtrig-cpu: registered to indicate activity on CPUs
[    1.081656] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[    1.081786] TCP: cubic registered
[    1.081853] NET: Registered protocol family 10
[    1.082042] mip6: Mobile IPv6
[    1.082046] NET: Registered protocol family 17
[    1.082051] mpls_gso: MPLS GSO support
[    1.082466] registered taskstats version 1
[    1.082899] rtc_cmos 00:01: setting system clock to 2017-01-08 21:59:27 UTC (1483912767)
[    1.082944] PM: Hibernation image not present or could not be loaded.
[    1.083713] Freeing unused kernel memory: 1204K (ffffffff818ee000 - ffffffff81a1b000)
[    1.083715] Write protecting the kernel read-only data: 8192k
[    1.084131] Freeing unused kernel memory: 896K (ffff880001520000 - ffff880001600000)
[    1.084871] Freeing unused kernel memory: 212K (ffff8800017cb000 - ffff880001800000)
[    1.094862] systemd-udevd[73]: starting version 215
[    1.095149] random: systemd-udevd urandom read with 4 bits of entropy available
[    1.106638] SCSI subsystem initialized
[    1.107024] ACPI: bus type USB registered
[    1.107053] usbcore: registered new interface driver usbfs
[    1.107066] usbcore: registered new interface driver hub
[    1.107153] usbcore: registered new device driver usb
[    1.107803] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.108042] libata version 3.00 loaded.
[    1.108100] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.108313] ehci-pci: EHCI PCI platform driver
[    1.108473] QUIRK: Enable AMD PLL fix
[    1.108498] ehci-pci 0000:00:12.2: EHCI Host Controller
[    1.108504] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 1
[    1.108510] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.108520] ehci-pci 0000:00:12.2: debug port 1
[    1.108570] ehci-pci 0000:00:12.2: irq 17, io mem 0xf3289000
[    1.110117] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.110352] r8169 0000:04:00.0: irq 44 for MSI/MSI-X
[    1.110565] r8169 0000:04:00.0 eth0: RTL8168f/8111f at 0xffffc900018f6000, 50:46:5d:b3:56:ff, XID 08000800 IRQ 44
[    1.110568] r8169 0000:04:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.111662] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.116972] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[    1.117062] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.117065] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.117067] usb usb1: Product: EHCI Host Controller
[    1.117069] usb usb1: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    1.117070] usb usb1: SerialNumber: 0000:00:12.2
[    1.117235] hub 1-0:1.0: USB hub found
[    1.117244] hub 1-0:1.0: 5 ports detected
[    1.117586] ehci-pci 0000:00:13.2: EHCI Host Controller
[    1.117594] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 2
[    1.117598] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.117610] ehci-pci 0000:00:13.2: debug port 1
[    1.117646] ehci-pci 0000:00:13.2: irq 17, io mem 0xf328a000
[    1.129118] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[    1.129247] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.129251] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.129253] usb usb2: Product: EHCI Host Controller
[    1.129254] usb usb2: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    1.129256] usb usb2: SerialNumber: 0000:00:13.2
[    1.129484] hub 2-0:1.0: USB hub found
[    1.129497] hub 2-0:1.0: 5 ports detected
[    1.129822] ehci-pci 0000:00:16.2: EHCI Host Controller
[    1.129828] ehci-pci 0000:00:16.2: new USB bus registered, assigned bus number 3
[    1.129832] ehci-pci 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.129841] ehci-pci 0000:00:16.2: debug port 1
[    1.129871] ehci-pci 0000:00:16.2: irq 17, io mem 0xf328b000
[    1.141081] ehci-pci 0000:00:16.2: USB 2.0 started, EHCI 1.00
[    1.141197] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    1.141201] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.141203] usb usb3: Product: EHCI Host Controller
[    1.141204] usb usb3: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    1.141205] usb usb3: SerialNumber: 0000:00:16.2
[    1.141362] hub 3-0:1.0: USB hub found
[    1.141373] hub 3-0:1.0: 4 ports detected
[    1.141567] ahci 0000:00:11.0: version 3.0
[    1.141817] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 8 ports 6 Gbps 0xff impl SATA mode
[    1.141820] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck led clo pio 
[    1.141864] ohci-pci: OHCI PCI platform driver
[    1.143560] scsi0 : ahci
[    1.143708] scsi1 : ahci
[    1.143830] scsi2 : ahci
[    1.143960] scsi3 : ahci
[    1.144095] scsi4 : ahci
[    1.144213] scsi5 : ahci
[    1.144337] scsi6 : ahci
[    1.144462] scsi7 : ahci
[    1.144527] ata1: SATA max UDMA/133 abar m2048@0xf3288000 port 0xf3288100 irq 19
[    1.144530] ata2: SATA max UDMA/133 abar m2048@0xf3288000 port 0xf3288180 irq 19
[    1.144533] ata3: SATA max UDMA/133 abar m2048@0xf3288000 port 0xf3288200 irq 19
[    1.144536] ata4: SATA max UDMA/133 abar m2048@0xf3288000 port 0xf3288280 irq 19
[    1.144539] ata5: SATA max UDMA/133 abar m2048@0xf3288000 port 0xf3288300 irq 19
[    1.144541] ata6: SATA max UDMA/133 abar m2048@0xf3288000 port 0xf3288380 irq 19
[    1.144543] ata7: SATA max UDMA/133 abar m2048@0xf3288000 port 0xf3288400 irq 19
[    1.144545] ata8: SATA max UDMA/133 abar m2048@0xf3288000 port 0xf3288480 irq 19
[    1.144673] ohci-pci 0000:00:12.0: OHCI PCI host controller
[    1.144679] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 4
[    1.144712] ohci-pci 0000:00:12.0: irq 18, io mem 0xf3284000
[    1.200997] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.201001] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.201003] usb usb4: Product: OHCI PCI host controller
[    1.201004] usb usb4: Manufacturer: Linux 3.16.0-4-amd64 ohci_hcd
[    1.201005] usb usb4: SerialNumber: 0000:00:12.0
[    1.201173] hub 4-0:1.0: USB hub found
[    1.201180] hub 4-0:1.0: 5 ports detected
[    1.201440] ohci-pci 0000:00:13.0: OHCI PCI host controller
[    1.201446] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5
[    1.201470] ohci-pci 0000:00:13.0: irq 18, io mem 0xf3285000
[    1.260940] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    1.260944] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.260945] usb usb5: Product: OHCI PCI host controller
[    1.260947] usb usb5: Manufacturer: Linux 3.16.0-4-amd64 ohci_hcd
[    1.260948] usb usb5: SerialNumber: 0000:00:13.0
[    1.261122] hub 5-0:1.0: USB hub found
[    1.261130] hub 5-0:1.0: 5 ports detected
[    1.261391] ohci-pci 0000:00:14.5: OHCI PCI host controller
[    1.261396] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 6
[    1.261421] ohci-pci 0000:00:14.5: irq 18, io mem 0xf3286000
[    1.320882] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    1.320886] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.320888] usb usb6: Product: OHCI PCI host controller
[    1.320889] usb usb6: Manufacturer: Linux 3.16.0-4-amd64 ohci_hcd
[    1.320890] usb usb6: SerialNumber: 0000:00:14.5
[    1.321053] hub 6-0:1.0: USB hub found
[    1.321061] hub 6-0:1.0: 2 ports detected
[    1.321284] ohci-pci 0000:00:16.0: OHCI PCI host controller
[    1.321289] ohci-pci 0000:00:16.0: new USB bus registered, assigned bus number 7
[    1.321315] ohci-pci 0000:00:16.0: irq 18, io mem 0xf3287000
[    1.380830] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    1.380833] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.380835] usb usb7: Product: OHCI PCI host controller
[    1.380837] usb usb7: Manufacturer: Linux 3.16.0-4-amd64 ohci_hcd
[    1.380838] usb usb7: SerialNumber: 0000:00:16.0
[    1.381003] hub 7-0:1.0: USB hub found
[    1.381010] hub 7-0:1.0: 4 ports detected
[    1.460736] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.460763] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.460789] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.460816] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.460838] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.460859] ata7: SATA link down (SStatus 0 SControl 300)
[    1.460884] ata5: SATA link down (SStatus 0 SControl 300)
[    1.461910] ata4.00: ATA-8: WDC WD10JPVT-22A1YT0, 01.01A01, max UDMA/133
[    1.461914] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    1.461925] ata6.00: ATA-8: WDC WD10JPVT-22A1YT0, 01.01A01, max UDMA/133
[    1.461928] ata6.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    1.461937] ata3.00: ATA-8: WDC WD10JPVT-22A1YT0, 01.01A01, max UDMA/133
[    1.461939] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    1.462687] ata2.00: ATAPI: PIONEER DVD-RW  DVR-218L, 1.02, max UDMA/100
[    1.463031] ata4.00: configured for UDMA/133
[    1.463043] ata6.00: configured for UDMA/133
[    1.463053] ata3.00: configured for UDMA/133
[    1.463342] ata2.00: configured for UDMA/100
[    1.464719] ata8: SATA link down (SStatus 0 SControl 300)
[    1.472955] ata1.00: ATA-8: OCZ-VERTEX3, 2.25, max UDMA/133
[    1.472958] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.482845] ata1.00: configured for UDMA/133
[    1.483109] scsi 0:0:0:0: Direct-Access     ATA      OCZ-VERTEX3      2.25 PQ: 0 ANSI: 5
[    1.485833] scsi 1:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-218L 1.02 PQ: 0 ANSI: 5
[    1.494933] scsi 2:0:0:0: Direct-Access     ATA      WDC WD10JPVT-22A 1A01 PQ: 0 ANSI: 5
[    1.495106] scsi 3:0:0:0: Direct-Access     ATA      WDC WD10JPVT-22A 1A01 PQ: 0 ANSI: 5
[    1.495279] scsi 5:0:0:0: Direct-Access     ATA      WDC WD10JPVT-22A 1A01 PQ: 0 ANSI: 5
[    1.498674] sd 0:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB)
[    1.498791] sd 0:0:0:0: [sda] Write Protect is off
[    1.498795] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.498828] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.499243]  sda: sda1
[    1.499526] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.510708] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.510712] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.510942] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.511214] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    1.511218] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[    1.511221] sd 5:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    1.511223] sd 5:0:0:0: [sdd] 4096-byte physical blocks
[    1.511232] sd 3:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    1.511233] sd 3:0:0:0: [sdc] 4096-byte physical blocks
[    1.511264] sd 2:0:0:0: [sdb] Write Protect is off
[    1.511266] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.511280] sd 5:0:0:0: [sdd] Write Protect is off
[    1.511283] sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[    1.511285] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.511298] sd 3:0:0:0: [sdc] Write Protect is off
[    1.511300] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    1.511314] sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.511383] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.511654] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.511708] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.511817] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    1.511862] sd 3:0:0:0: Attached scsi generic sg3 type 0
[    1.511906] sd 5:0:0:0: Attached scsi generic sg4 type 0
[    1.555291]  sdc: sdc1
[    1.555548] sd 3:0:0:0: [sdc] Attached SCSI disk
[    1.557559]  sdd: sdd1
[    1.557791] sd 5:0:0:0: [sdd] Attached SCSI disk
[    1.561056]  sdb: sdb1
[    1.561372] sd 2:0:0:0: [sdb] Attached SCSI disk
[    1.804381] tsc: Refined TSC clocksource calibration: 3693.280 MHz
[    1.948291] usb 2-4: new high-speed USB device number 2 using ehci-pci
[    2.028687] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    2.081014] usb 2-4: New USB device found, idVendor=0781, idProduct=5530
[    2.081018] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.081019] usb 2-4: Product: Cruzer
[    2.081021] usb 2-4: Manufacturer: SanDisk
[    2.081022] usb 2-4: SerialNumber: 20053045400CB8F07F6E
[    2.082441] usb-storage 2-4:1.0: USB Mass Storage device detected
[    2.082630] scsi8 : usb-storage 2-4:1.0
[    2.082710] usbcore: registered new interface driver usb-storage
[    2.182181] random: nonblocking pool is initialized
[    2.471765] usb 4-3: new full-speed USB device number 2 using ohci-pci
[    2.644736] usb 4-3: New USB device found, idVendor=03f0, idProduct=a407
[    2.644739] usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.644741] usb 4-3: Product: HP Link-5 micro dongle
[    2.644743] usb 4-3: Manufacturer: HP
[    2.647942] hidraw: raw HID events driver (C) Jiri Kosina
[    2.657036] usbcore: registered new interface driver usbhid
[    2.657039] usbhid: USB HID core driver
[    2.657784] input: HP HP Link-5 micro dongle as /devices/pci0000:00/0000:00:12.0/usb4/4-3/4-3:1.0/0003:03F0:A407.0001/input/input1
[    2.657844] hid-generic 0003:03F0:A407.0001: input,hidraw0: USB HID v1.11 Keyboard [HP HP Link-5 micro dongle] on usb-0000:00:12.0-3/input0
[    2.658196] input: HP HP Link-5 micro dongle as /devices/pci0000:00/0000:00:12.0/usb4/4-3/4-3:1.1/0003:03F0:A407.0002/input/input2
[    2.658316] hid-generic 0003:03F0:A407.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [HP HP Link-5 micro dongle] on usb-0000:00:12.0-3/input1
[    2.803546] Switched to clocksource tsc
[    2.907353] usb 4-4: new full-speed USB device number 3 using ohci-pci
[    3.068335] usb 4-4: New USB device found, idVendor=0557, idProduct=8021
[    3.068338] usb 4-4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.070376] hub 4-4:1.0: USB hub found
[    3.072326] hub 4-4:1.0: 4 ports detected
[    3.079954] scsi 8:0:0:0: Direct-Access     SanDisk  Cruzer           1.02 PQ: 0 ANSI: 2
[    3.080266] sd 8:0:0:0: Attached scsi generic sg5 type 0
[    3.081638] sd 8:0:0:0: [sde] 7813120 512-byte logical blocks: (4.00 GB/3.72 GiB)
[    3.082592] sd 8:0:0:0: [sde] Write Protect is off
[    3.082595] sd 8:0:0:0: [sde] Mode Sense: 03 00 00 00
[    3.083640] sd 8:0:0:0: [sde] No Caching mode page found
[    3.083694] sd 8:0:0:0: [sde] Assuming drive cache: write through
[    3.088383]  sde: sde1
[    3.091945] sd 8:0:0:0: [sde] Attached SCSI removable disk
[    3.317131] ISO 9660 Extensions: Microsoft Joliet Level 3
[    3.319710] ISO 9660 Extensions: RRIP_1991A
[    3.326702] aufs: module is from the staging directory, the quality is unknown, you have been warned.
[    3.327521] aufs 3.16-20140908+setfl
[    3.335708] loop: module loaded
[    3.347735] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    3.362913] usb 4-4.1: new full-speed USB device number 4 using ohci-pci
[    3.484849] usb 4-4.1: New USB device found, idVendor=046d, idProduct=c326
[    3.484853] usb 4-4.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.484855] usb 4-4.1: Product: USB Keyboard
[    3.484857] usb 4-4.1: Manufacturer: Logitech
[    3.503214] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb4/4-4/4-4.1/4-4.1:1.0/0003:046D:C326.0003/input/input3
[    3.504789] hid-generic 0003:046D:C326.0003: input,hidraw2: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-0000:00:12.0-4.1/input0
[    3.538897] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb4/4-4/4-4.1/4-4.1:1.1/0003:046D:C326.0004/input/input4
[    3.539022] hid-generic 0003:046D:C326.0004: input,hiddev0,hidraw3: USB HID v1.10 Device [Logitech USB Keyboard] on usb-0000:00:12.0-4.1/input1
[    4.043121] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    4.043271] systemd[1]: Detected architecture 'x86-64'.
[    4.099964] systemd[1]: Inserted module 'autofs4'
[    4.102979] systemd[1]: Set hostname to <localhost.localdomain>.
[    4.103171] systemd[1]: Initializing machine ID from random generator.
[    4.197922] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    4.198213] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    4.198267] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    4.198275] systemd[1]: Starting Remote File Systems (Pre).
[    4.198299] systemd[1]: Reached target Remote File Systems (Pre).
[    4.198312] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[    4.198343] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    4.198350] systemd[1]: Starting Paths.
[    4.198357] systemd[1]: Reached target Paths.
[    4.198382] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    4.198455] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    4.198464] systemd[1]: Starting Encrypted Volumes.
[    4.198471] systemd[1]: Reached target Encrypted Volumes.
[    4.198477] systemd[1]: Starting Swap.
[    4.198485] systemd[1]: Reached target Swap.
[    4.198491] systemd[1]: Starting Root Slice.
[    4.198512] systemd[1]: Created slice Root Slice.
[    4.198518] systemd[1]: Starting User and Session Slice.
[    4.198550] systemd[1]: Created slice User and Session Slice.
[    4.198556] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[    4.198588] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    4.198595] systemd[1]: Starting Delayed Shutdown Socket.
[    4.198614] systemd[1]: Listening on Delayed Shutdown Socket.
[    4.198621] systemd[1]: Starting Journal Socket (/dev/log).
[    4.198649] systemd[1]: Listening on Journal Socket (/dev/log).
[    4.198659] systemd[1]: Starting udev Control Socket.
[    4.198677] systemd[1]: Listening on udev Control Socket.
[    4.198686] systemd[1]: Starting udev Kernel Socket.
[    4.198701] systemd[1]: Listening on udev Kernel Socket.
[    4.198709] systemd[1]: Starting Journal Socket.
[    4.198734] systemd[1]: Listening on Journal Socket.
[    4.198745] systemd[1]: Starting System Slice.
[    4.198771] systemd[1]: Created slice System Slice.
[    4.198779] systemd[1]: Starting system-getty.slice.
[    4.198815] systemd[1]: Created slice system-getty.slice.
[    4.198833] systemd[1]: Starting Increase datagram queue length...
[    4.199219] systemd[1]: Mounting Huge Pages File System...
[    4.199556] systemd[1]: Mounting POSIX Message Queue File System...
[    4.200026] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    4.200456] systemd[1]: Mounting Debug File System...
[    4.203722] systemd[1]: Started Set Up Additional Binary Formats.
[    4.203769] systemd[1]: Starting live-config contains the components that configure a live system during the boot process (late userspace)....
[    4.234426] systemd[1]: Starting Load Kernel Modules...
[    4.234877] systemd[1]: Starting udev Coldplug all Devices...
[    4.235266] systemd[1]: Starting Slices.
[    4.235279] systemd[1]: Reached target Slices.
[    4.236223] systemd[1]: Started Increase datagram queue length.
[    4.238537] systemd[1]: Starting Syslog Socket.
[    4.238569] systemd[1]: Listening on Syslog Socket.
[    4.238582] systemd[1]: Starting Journal Service...
[    4.239006] systemd[1]: Started Journal Service.
[    8.089064] systemd-udevd[755]: starting version 215
[    8.312636] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.363934] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
[    8.363939] ACPI: Power Button [PWRB]
[    8.363994] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[    8.363996] ACPI: Power Button [PWRF]
[    8.391270] systemd-journald[493]: Received request to flush runtime journal from PID 1
[    8.397914] ACPI: acpi_idle registered with cpuidle
[    8.418576] acpi-cpufreq: overriding BIOS provided _PSD data
[    8.441003] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    8.441042] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[    8.488287] input: PC Speaker as /devices/platform/pcspkr/input/input7
[    8.607330] AVX version of gcm_enc/dec engaged.
[    8.616820] [drm] Initialized drm 1.1.0 20060810
[    8.623343] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[    8.626677] snd_hda_intel 0000:01:00.1: Disabling MSI
[    8.626687] snd_hda_intel 0000:01:00.1: Handle VGA-switcheroo audio client
[    8.636902] alg: No test for crc32 (crc32-pclmul)
[    8.681634] sound hdaudioC0D0: autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[    8.681642] sound hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    8.681645] sound hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[    8.681647] sound hdaudioC0D0:    mono: mono_out=0x0
[    8.681648] sound hdaudioC0D0:    dig-out=0x11/0x1e
[    8.681650] sound hdaudioC0D0:    inputs:
[    8.681652] sound hdaudioC0D0:      Front Mic=0x19
[    8.681655] sound hdaudioC0D0:      Rear Mic=0x18
[    8.681656] sound hdaudioC0D0:      Line=0x1a
[    8.683574] wmi: Mapper loaded
[    8.696219] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/sound/card0/hdaudioC0D0/input8
[    8.700429] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
[    8.700677] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
[    8.701282] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
[    8.701553] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
[    8.701808] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input13
[    8.702074] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input14
[    8.703175] input: HD-Audio Generic Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input15
[    8.703455] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input16
[    8.710346] kvm: Nested Virtualization enabled
[    8.710350] kvm: Nested Paging enabled
[    8.752009] nouveau  [  DEVICE][0000:01:00.0] BOOT0  : 0x117000a2
[    8.752012] nouveau  [  DEVICE][0000:01:00.0] Chipset: GM107 (NV117)
[    8.752014] nouveau  [  DEVICE][0000:01:00.0] Family : NV110
[    8.752035] nouveau  [   VBIOS][0000:01:00.0] checking PRAMIN for image...
[    8.752043] nouveau  [   VBIOS][0000:01:00.0] ... signature not found
[    8.752044] nouveau  [   VBIOS][0000:01:00.0] checking PROM for image...
[    8.792668] nouveau  [   VBIOS][0000:01:00.0] ... appears to be valid
[    8.792670] nouveau  [   VBIOS][0000:01:00.0] using image from PROM
[    8.792774] nouveau  [   VBIOS][0000:01:00.0] BIT signature found
[    8.792777] nouveau  [   VBIOS][0000:01:00.0] version 82.07.32.40.47
[    8.793134] nouveau 0000:01:00.0: irq 45 for MSI/MSI-X
[    8.793143] nouveau  [     PMC][0000:01:00.0] MSI interrupts enabled
[    8.793172] nouveau  [     PFB][0000:01:00.0] RAM type: GDDR5
[    8.793173] nouveau  [     PFB][0000:01:00.0] RAM size: 2048 MiB
[    8.793175] nouveau  [     PFB][0000:01:00.0]    ZCOMP: 0 tags
[    8.794135] nouveau  [     CLK][0000:01:00.0] 07: core 405 MHz memory 810 MHz 
[    8.794370] nouveau  [     CLK][0000:01:00.0] 0f: core 270-1398 MHz memory 5400 MHz 
[    8.794448] nouveau  [     CLK][0000:01:00.0] --: core 405 MHz memory 810 MHz 
[    8.799898] nouveau  [  PGRAPH][0000:01:00.0] using external firmware
[    8.799947] nouveau 0000:01:00.0: firmware: failed to load nouveau/nv117_fuc409c (-2)
[    8.800002] nouveau 0000:01:00.0: Direct firmware load failed with error -2
[    8.800004] nouveau 0000:01:00.0: Falling back to user helper
[    8.800726] nouveau 0000:01:00.0: firmware: failed to load nouveau/fuc409c (-2)
[    8.800788] nouveau 0000:01:00.0: Direct firmware load failed with error -2
[    8.800791] nouveau 0000:01:00.0: Falling back to user helper
[    8.801268] nouveau E[  DEVICE][0000:01:00.0] failed to create 0x18000717, -22
[    8.801333] nouveau E[     DRM] failed to create 0x80000080, -22
[    8.802623] nouveau: probe of 0000:01:00.0 failed with error -22
[    8.884128] r8169 0000:04:00.0: firmware: failed to load rtl_nic/rtl8168f-1.fw (-2)
[    8.884191] r8169 0000:04:00.0: Direct firmware load failed with error -2
[    8.884194] r8169 0000:04:00.0: Falling back to user helper
[    8.884794] r8169 0000:04:00.0 eth0: unable to load firmware patch rtl_nic/rtl8168f-1.fw (-12)
[    8.896639] r8169 0000:04:00.0 eth0: link down
[    8.896659] r8169 0000:04:00.0 eth0: link down
[    8.896701] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    9.079455] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input17
[    9.079711] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input18
[    9.080022] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input19
[    9.357176] RPC: Registered named UNIX socket transport module.
[    9.357179] RPC: Registered udp transport module.
[    9.357180] RPC: Registered tcp transport module.
[    9.357181] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    9.369527] FS-Cache: Loaded
[    9.390070] FS-Cache: Netfs 'nfs' registered for caching
[    9.438243] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   11.331313] r8169 0000:04:00.0 eth0: link up
[   11.331328] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready